Tender For Beautification Work At Kachhari Chauraha, Including Renovation And The Installation Of A Lighting System.
Tender Value
35.75 Lakhs
Estimated cost
Bid Submission
24 Sep 2026
0 days left
EMD
3.57 Lakhs
Bank guarantee accepted
Document Fee
4218
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jhansi → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Beautification Work At Kachhari Chauraha, Including Renovation And The Installation Of A Lighting System.
BOQ
| Sl. No. | Item Description |
| 1 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. As per DSR 15.3 |
| 2 | Demolishing Brick work Manually/ by mechanical means Including Stacking of Serviceable material and disposal of unseviceable material within 50 metres lead as per direction of Engineer -in-charge.Cement Mortar |
| 3 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more. |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kind of soil |
| 5 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 7 | 12 mm cement plaster on plinth of mix : 1:4 (1 cement: 4 coarse sand). F.M.-1.25 |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Providing & applying white cement based putty of average thickness 1 mm, of approved brand & manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. As Per DSR 13.80. |
| 10 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand & manufacture, including applying additional coats wherever required, to achieve even shade & colour. As per DSR 13.82.2 |
| 11 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). As Per DSR 16.69 |
| 12 | (Road Signage)- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per som area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC 35-2015 The finished surface to be level, uniform and free from streaks and holes. |
| 13 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67 upto date made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with PCC M-25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date. Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.3.7 . Proof of the same in form of government report shall be uploaded while quoting tender.(For Main Road) 60cm circular with definition plate (20cmx660cm). |
| 14 | 60 cm equilateral triangle with definition plate (20cm X 60cm) |
| 15 | 60 mm x 45 mm rectangular with diffinitation plate (20cm X 60cm) |
| 16 | x) 30X90 cm (Left/Right) Object Hazard |
| 17 | Direction and place Identification signs up to 0.90 sqm size Board 8.5) Providing & erecting direction and place identification retro-reflectorised sign as per IRC-67 made of high intensity grade sheeting The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility. liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation,the Employer/ Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012. Legends, letters, numerals & borders etc should be as per MoRTH specification No-801.3.7 Sheet fixed over aluminium sheeting 2 mm thick with area not exceeding 0.9 sqm. Supported on a mild steel single angle iron post 75x75x6 mm firmly fixed to the ground by means of property designed foundation with M-15 grade cement concrete 45x45x60 cm., below ground level as per approved drawing, complete. |
| 18 | Reflective Raised Pavement Markers (Cat Eye/ Road Stud) Supply and fixing of raised pavement marker with Made of Plastic body of RPM/ Road Stud shall be moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High-Impact Polystyrene) or Acrylonitrile Butadien Styrene (ABS) or Any other suitable material approved by the Engineer.The Marker shall support a load of 13,635 kg tested in accordance with ASTM D4280.The Reflective panels shall consist of number of lenses contatning single or dual prismatic cubes capable of providing total internal reflection of the light entring the lens face.Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 or equivalent.The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro -reflecting surface shall not be less than 13.00 sq.cm. marker height shall not be less than 10 mm and shall not exceed 20 mm & Width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm all road studs shall be legibly marked with the name,trade or other means of identification of the manufacture. epoxy installations,excess adhesive around the edge of the marker,excess adhesive on the pavement & adhesive on the exposed surfaces of the markers shall be immediately removed. The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel ,to the Engineer . In addition , a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers. In case the markers are displaced , damaged , get worn out or lose their reflectivity compared to stipulated standards , the contractor would be required to replace all such markers within 15 days of the intimation from the Engineer , at his own cost. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge.As per SOR ch-26 SI no.-5RPM with Shank |
| 19 | The solar studs shall be made of Aluminium alloy and poly carbonate material which shall be absolutely weather resistant and strong enough to support a load of 13,635 kg tested in accordance with ASTM D4280. Its colour may be white , red , yellow , green or blue or combination as directed by the Engineer . Its water resistance shall meet the requirements of IP 65 in accordance with IS:12063:1987 category 2 for protection against water ingress.The dimensions of solar studs shall not be less than 100 mm X 100 mm X 10 mm . It shall have super bright LEDs so as to provide long visibility from a distance of more than 800 m. Its flashing rate shall not be less than 1 Hz . Its should be able to give the prescribed performance in the temperrature range of - 400C to +550C. Its life shall be not less than 3 Years. The rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in-Charge. |
| 20 | Aluminum-backed flexible prismatic sheeting shall be made of yellow colored flexible prismatic sheeting with non-metallic prismatic lens formed in a transparent, synthetic resin as retro reflective elements. This flexible prismatic sheeting shall have black and yellow stripes with aluminum backed flexible prismatic Type VI sheeting conforming to ASTM: D4956 . specifications and standards of coefficient of retro reflectivity, flexibility and impact resistance applicable for reboundable devices. This flexible prismatic sheeting shall have screen printed arrow/slant line pattern in black colour in a continuous roll format. Width of object marker shall be 300 mm. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. |
| 21 | Flexible Median Marker (FMM) should be used for improving median visibility during dark hours. , Use of Median Marker provides safety against collision happening with medians during night time , or severe weather. Flexible Median Markers shall be provided with fluorescent yellow colour retro-reflective sheeting Type XI as per IRC:67. Flexible Median Marker shall be of tough, high impact resistant, injection-molded, thermoplastic body with property of flexibility to provide high durability 'and U shape structure having rebound / bounce back property. the sheeting shall be of Type XI conforming to IRC:67 and it should be on both .the faces whereby providing maximum reflectivity at l,anger distances with adequate durability. The logo of the manufacturer shall be embossed on either side of the body during the injection molding process. FMM shall be fixed by a combination bf epoxy adhesive and grouting/ drilling on concrete medians or properly constructed solid medians. Height: The marker height shall be a minimum of 180 mm. width 120 mm & Body Thickness: 6.5 mm. the shanks shall not be less than 20 mm and depth shall not be less than 30 rnm Reflective Area: Shall not be less than 90 cm square . Proof of the same Report shall be uploaded which quoting tender. The body of FMM shall bounce back to its original position of after 750 number of hits using pendulum of 1.8 kg conforming 40 ASTM D256 adhesion between the body and outer casing body of FMM shall with stand 50 kg f Tensile loads conforming to ASTM D638 method. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. |
| 22 | S/F of plastic Tubular bollards having 450 mm to 700 mm Height, shall be attached to the pavemet to display the minimum 50 mm width of reflective bands to the approaching road users including labour, material, T&P etc. for propar completion of the work. |
| 23 | \\"Decorative Railing made of MS Pannel which provide a classic and timeless architectural appeal. These ornamental sections are securely framed by a 6mm thick FRP Panel border, creating a sleek, clean-edged perimeter that transitions the decorative core into a modern, structured silhouette. The entire assembly is anchored by vertical poles on either side, providing the necessary lateral stability and heavy-duty support required for safety. This combination of materials ensures a high-strength barrier with a slim profile, often finished with a powder coating or matte paint to protect against corrosion while highlighting the contrast. The Cost Includes Transportation, and all other labour cost are included. Make in or Equivalent. |
| 24 | LOGO PILLAR is a rectangular, freestanding pillar or bollard, likely functioning as an outdoor light fixture or decorative boundary marker. It features a dark brown FRp Sheet 5mm of thickness with intricate CNC cutting designs, backed by a translucent Acrylic white panel intended to diffuse light, often finished with a powder coating or matte paint to protect against corrosion. The full name \\" DEVELOPMENT AUTHORITY\\" is engraved or cut out in an arc along the bottom half of the circle on one side and other side logo is engraved. The Cost Includes CNC FRP Fabrication,Transportation, and all other labour cost are included. Make in or Equivalent.(900MM) |
| 25 | (Horticulture)-Providing and stacking Alternanthera species of height 15 cm to 20 cm,full of branches and foliage in 15 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge. |
| 26 | Providing, stacking and Displaying Ixora dwarf different colour having 10 cm to 15 cm ht., well developed with fresh & healthy foliage with bloom in 15 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. |
| 27 | Providing and stacking of Zinnia in different colour with fresh and healthy bud stage in polybag of size 10 cm and as per direction of the officer-incharge. |
| 28 | Providing and stacking of Portulaca Hybrid in different colour with fresh and healthy bud stage in polybag of size 10 cm and as per direction of the officer-in-charge. |
| 29 | Providing and stacking of Petunia hybrid in different colour with freshand healthy bud stage in polybag of size 10 cm and as per direction of the officer-in-charge. |
| 30 | Providing and stacking of Dianthus hybrid in different colour with fresh and healthy bud stage in polybag of size 10 cm and as per direction of the officer-in-charge. |
| 31 | Providing and stacking Duranta Golden, having ht.12 cm to 15 cm bushyshape with fresh and healthy leaves in Poly Bag and as per direction of the officer-in-charge. |
| 32 | (Abstract of Light work). Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (GroupC) |
| 33 | Providng and laying and installation of electrical cable |
| 34 | Supple & FIxing of decorative type led focus/pathway/uplightslight with die cast aluminium housing built with driver set conforming to IP 66 water resistant protection complete in all respect |
| 35 | Providing and fixing of Spike Light in Graphite grey powder coated integral aluminium housing Die-cast aluminium housing comprises Warm White (WW) COB LED and reflector COB LED colour temperature: 3000K+250K COB LED housing covered with die-cast aluminium ring with weatherproof gasket and toughened glass Adjustable mounting bracket with spike is provided for easy focus on the object 2 nos. Ø8mm holes also provided on adjustable mounting bracket for surface mounting Highly efficient constant current electronic driver having operating voltage range from 140-280 Volt AC; provided with high voltage, open and short circuit protection Luminaire is wired with inbuilt driver with 4.5kV surge protection Degree of protection: IP65 as directed by Engineer-in- charge |
| 36 | Providing and Fixing of The luminaire comprises of a white powder coated cast aluminium body Low power White LEDS (WH) covered with heat resistant frosted glass fixed to the housing with frame protection grill LED colour temperature: 5700K +300K Highly efficient constant current electronic driver having operating voltage range from 140-280 Volt AC; provided with high voltage, open and short circuit protection Degree of protection: IP54 |
| 37 | Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required |
| 38 | P&F cage of size 300mm x 300mm x 350mm using MS bars welded together to form a strong case. The cost includes moulding, welding, fixing, etc. all complete using all necessary screws, bolts, etc. |
| 39 | Add Consultancy @1.5% on Rs.35.62 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodaySep 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
TodayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender