Tender For Interior Works For New Head Office Building For Malabar Milma (Mrcmpu Ltd.)
Tender Value
2.55 Crore
Estimated cost
Bid Submission
28 Sep 2026
21 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
7500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kozhikode → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Interior Works For New Head Office Building For Malabar Milma (Mrcmpu Ltd.)
BOQ
| Sl. No. | Item Description |
| 1 | Partition works |
| 2 | Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with AlZn coating of 150 gsm (Gypserra or equivalent), consisting of floor and ceiling channel 72 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and true ceiling at the spacing of 610 mm centre to centre with Gyproc® Rawl plug Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} /Hilti X-GN20MX anchor fasteners or equivalent anchor fastners and the studs 70 mm wide having flange of 40 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre, including fixing of studs along both ends of partition fixed flush to wall, and fixing of boards to both side of frame work by 25/35 mm long dry wall screws (Gyproc®Drywall Screw or equivalent) on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks and angle beads at corners. The board shall be jointed and finished to have a flushed look by filling and finishing with proprietary supplied jointing tape & joint compound and two coats of dry wall coats as per manufacturer's specification. Joints to be sand papered to achieve a smooth and seamless finish as per engineer's approval. 98 mm overall thickness partition with 13 mm thick double skin tapered edged high impact resistant Gypsum board (Gyproc Rigiroc or equivalent) including providing and applying two coat putty. (Total front elevation area of the partition (one side) will be measured in square meter for payment) |
| 3 | Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with AlZn coating of 150 gsm (Gypserra or equivalent), consisting of floor and ceiling channel 72 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and true ceiling at the spacing of 610 mm centre to centre with Gyproc® Rawl plug Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} /Hilti X-GN20MX anchor fasteners or equivalent anchor fastners and the studs 70 mm wide having flange of 40 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre, including fixing of studs along both ends of partition fixed flush to wall, and fixing of boards to both side of frame work by 25/35 mm long dry wall screws (Gyproc®Drywall Screw or equivalent) on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks and angle beads at corners. 50mm Glasswool of density 20kg/m3 shall be placed in Metal framework with the help of holding Clip.The board shall be jointed and finished to have a flushed look by filling and finishing with proprietary supplied jointing tape & joint compound and two coats of dry wall coats as per manufacturer's specification. Joints to be sand papered to achieve a smooth and seamless finish as per engineer's approval. 98 mm overall thickness partition with 13 mm thick double skin tapered edged high impact resistant Gypsum board (Gyproc Rigiroc or equivalent) including providing and applying two coat putty. (Total front elevation area of the partition (one side) will be measured in square meter for payment) |
| 4 | Providing, fabricating and fixing in position glazed full partition work as per the drawing, in well seasoned ash wood frame work of 100mmx75mm (corner joints - 100mmx100mm) panelled with 10mm thick toughened plain glass and natural rattan finish sandwitched between two 4mm toughended plain glasses as per the drawing including cutting grooves, providing and fixing reapers, EPDM/neoprene etc. All the wood surfaces shall be polished with 1 coat epoxy insulator, 2 coat melamine sealer and 2 coat melamine interior matt as per manufacture recommendations. The fabricated partition shall be securely fixed to the position. (Total front elevation area of the partition (one side) will be measured in square meter for payment) |
| 5 | Description same as that of the above (Serial No 4), but with 10mm thick etched toughened glass as per the approved design. |
| 6 | Providing and fixing half-height decorative partition wall up to 1200mm height from finished floor level and 75mm overall thickness, comprising an internal rigid framework of seasoned hardwood timber sections or built-up BWP plywood (IS 710 grade) strips securely glued and screwed together, anchored to the floor and adjacent walls with approved fasteners, clad on both sides with 16mm thick BWP plywood (IS 710 grade), finished on all exposed surfaces with 1mm thick decorative laminate of approved shade and texture, and incorporating 8mm thick clear toughened glass fixed in grooves/rebates with approved quality silicone sealant and EPDM rubber gaskets, complete in all respects as per approved drawings and specifications, including all materials, hardware, adhesives, fasteners, sealants, cutting and fitting, transportation, scaffolding, labour, tools, wastage, and all. (Total front elevation area of the partition (one side) will be measured in square meter for payment) |
| 7 | False ceiling works |
| 8 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 150 gms/ sqm as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts (Hilty/equiv), other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of Gyproc® Rawl Plug- Ø8x45mm {Material-IS 513 CR2 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} or equivalent rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, suspension points and clips shall be able to take a minimum safe load of 50 kgs including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound (Conforms to ASTM C475), jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, making of cove all complete as per drawings, specification and direction of the Engineer in Charge including two coat putty: 12.5 mm thick tapered edge gypsum plain board. (gI frame: Gypserra/equivalent, gypsm board : Gyproc/equivalent) |
| 9 | Description same as that of the above (Serial No 8), but with 12.5 mm thick tapered edge non-paper faced gypsum boards reinforced with glass mats. (gi frame: Gypserra/equivalent, gypsm board : Gyproc Glasroc H/equivalent) instead of gypsum plain board. |
| 10 | Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24 kg/ m3, 50 mm thcik, wrapped in 200 G Virgin Polythene bags placed over existing false ceiling and held in position by crisscrossing GI wire. |
| 11 | Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile size 595x595 mm made of Gypsum plasterboard , manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyster on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyster film so as to make the tile a completely sealed unit. (gyproc/ equivalent) |
| 12 | Providing and fixing Perforated false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 150 gms/ sqm as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts (Hilty/equiv), other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of Gyproc® Rawl Plug- Ø8x45mm {Material-IS 513 CR2 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} or equivalent rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, suspension points and clips shall be able to take a minimum safe load of 50 kgs including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound (Conforms to ASTM C475), jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge including two coat putty: Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.9. The ceiling shall be backed with 50mm thick 1000GSM polyester wool OR 50mm thick Polyester Wool having 48Kg/m3 density. |
| 13 | Providing and fixing factory-manufactured PVC fluted panels of size 3000 mm × 300 mm × 20 mm thickness, with flutes spaced at 15 mm c/c, fixed over 12 mm thick BWP plywood (IS 710 grade). The plywood shall be supported on a base framework identical to that specified under Item No. 2.001. The exposed surface of the PVC fluted panels shall be finished with approved shade and quality PU paint, complete as per the Architect's drawings and instructions. The rate shall include the cost of PVC fluted panels, 12 mm BWP plywood backing, supporting framework, all necessary fasteners, adhesives, PU painting, labour, scaffolding, cutting, fitting, wastage, etc complete. (The actual finished surface area executed shall be measured and paid for). |
| 14 | Supply & Installation of Aluminium Baffle ceiling and cladding consists of Baffle Panel of U profile of size 25 (w) x 100 (h) x 1.0mm thickness @ 50mm center to center spacing. These Baffle panels are powder coated in approved wooden finish (as per Architect approval). The Baffle panels are fixed on to the \\"C\\" type GI Carrier of 0.8mm thickness in Black color which has slots of definite spacings as per the design requirement. This way the Baffle panels are fixed at definite spacings as per design using Bolt and Nut. The C Carrier is then suspended at every 1mtr with 6mm threaded rod, where one end is connected to the carrier and the other end with anchor fastner fixed on true ceiling. The rate shall also include the cost of providing and fixing 12mm BWP plywood (IS 710 grade) back panel behind the aluminium baffle ceiling painted with approved colour. |
| 15 | Door works |
| 16 | Providing and fixing 40 mm thick premium block board flush double door shutter with teak wood frame and vision panel complete for the specified opening size, conforming to IS: 2202 (Part 1), comprising first-class teak wood frame of size 100 mm × 75 mm with necessary rebates fixed in position using approved dash fasteners of required size; shutter made of well-seasoned preservative-treated hardwood/pine wooden battens bonded under high pressure with Boiling Water Proof (BWP) phenol formaldehyde synthetic resin, faced on both sides with 1.0 mm thick premium decorative teak wood veneer of approved shade and grain; including providing precision machine-cut opening for vision panel of specified size and securely fixing 8 mm thick clear toughened glass as per approved drawings; providing a neatly machined meeting rebate at the center; finishing all exposed wooden surfaces with one coat epoxy wood insulator, two coats melamine sealer and two coats interior-grade matte melamine polish of approved shade; including supplying and fixing heavy-duty stainless steel butt hinges, premium mortise lock with handles, stainless steel tower bolt, door stopper, dash fasteners, screws, adhesives, sealants and all other necessary fittings, fixtures, accessories, labour, transportation, polishing, tools and tackles, complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge. The door shall have minimum 30 year warrantee. |
| 17 | Opening size = 200 x 240 cm |
| 18 | Opening size = 160 x 210 cm |
| 19 | Providing and fixing 40 mm thick premium block board flush door shutter to existing frame with vision panel complete for the specified opening size, conforming to IS: 2202 (Part 1); shutter made of well-seasoned preservative-treated hardwood/pine wooden battens bonded under high pressure with Boiling Water Proof (BWP) phenol formaldehyde synthetic resin, faced on both sides with 1.0 mm thick premium decorative teak wood veneer of approved shade and grain; including providing precision machine-cut opening for vision panel of specified size and securely fixing 8 mm thick clear toughened glass/fluted glass as per approved drawings; finishing all exposed wooden surfaces with one coat epoxy wood insulator, two coats melamine sealer and two coats interior-grade matte melamine polish of approved shade; including supplying and fixing heavy-duty stainless steel butt hinges, premium mortise lock with handles, stainless steel tower bolt, door stopper, dash fasteners, screws, adhesives, sealants and all other necessary fittings, fixtures, accessories, labour, transportation, polishing, tools and tackles, complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge. The door shutter shall have minimum 30 year warrantee.Door size = 100 x 210 cm (Chairman, MD, GMs rooms) |
| 20 | Providing and fixing 35 mm thick premium block board flush door shutter with teak wood frame and vision panel complete for the specified opening size, conforming to IS: 2202 (Part 1), comprising first-class teak wood frame of size 100 mm × 75 mm with necessary rebates fixed in position using approved dash fasteners of required size; shutter made of well-seasoned preservative-treated hardwood/pine wooden battens bonded under high pressure with Boiling Water Proof (BWP) phenol formaldehyde synthetic resin, faced on both sides with 1.0 mm thick premium decorative teak wood veneer of approved shade and grain; including providing precision machine-cut opening for vision panel of specified size and securely fixing 8 mm thick clear toughened glass as per approved drawings; finishing all exposed wooden surfaces with one coat epoxy wood insulator, two coats melamine sealer and two coats interior-grade matte melamine polish of approved shade; including supplying and fixing heavy-duty stainless steel butt hinges, premium mortise lock with handles, stainless steel tower bolt, door stopper, dash fasteners, screws, adhesives, sealants and all other necessary fittings, fixtures, accessories, labour, transportation, polishing, tools and tackles, complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge. The door shutter shall have minimum 30 year warrantee. |
| 21 | Opening size = 100 x 210 cm |
| 22 | Opening size = 100 x 220 cm |
| 23 | Opening size = 100 x 240 cm |
| 24 | Providing and fixing 35 mm thick premium block board flush door shutter with teak wood frame complete for the specified opening size, conforming to IS: 2202 (Part 1), comprising first-class teak wood frame of size 100 mm × 75 mm with necessary rebates fixed in position using approved dash fasteners of required size; shutter made of well-seasoned preservative-treated hardwood/pine wooden battens bonded under high pressure with Boiling Water Proof (BWP) phenol formaldehyde synthetic resin, faced on both sides with 1.0 mm thick premium decorative teak wood veneer of approved shade and grain; finishing all exposed wooden surfaces with one coat epoxy wood insulator, two coats melamine sealer and two coats interior-grade matte melamine polish of approved shade; including supplying and fixing heavy-duty stainless steel butt hinges, premium mortise lock with handles, stainless steel tower bolt, door stopper, dash fasteners, screws, adhesives, sealants and all other necessary fittings, fixtures, accessories, labour, transportation, polishing, tools and tackles, complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge. The door shutter shall have minimum 30 year warrantee. |
| 25 | Opening size = 90 x 210 cm |
| 26 | Opening size = 100 x 210 cm |
| 27 | Opening size = 100 x 220 cm |
| 28 | Opening size = 120 x 210 cm |
| 29 | Opening size = 120 x 220 cm |
| 30 | Providing, fabricating and fixing in position fully glazed glass door in well seasoned ash wood outer frame work of 100mmx75mm and shutter frame of well seasoned ashwood frame of size 55mmx100mm panelled with 10mm thick toughened plain glass and natural rattan finish sandwitched between two 4mm toughended plain glasses as per the drawing including cutting grooves, EPDM/neoprene etc. All the wood surfaces shall be polished with 1 coat epoxy insulator, 2 coat melamine sealer and 2 coat melamine interior matt as per manufacture recommendations including supplying and fixing heavy-duty stainless steel butt hinges, premium mortise lock with handles, stainless steel tower bolt, door stopper, dash fasteners, screws, adhesives, sealants and all other necessary fittings, fixtures, accessories, labour, transportation, polishing, tools and tackles, complete in all respects as per approved drawings, specifications and the directions of the Engineer-in-Charge.Opening size = 100x240 cm |
| 31 | Providing, fabricating and fixing powder coated fully glazed four track four panelled sliding doors made of powder coated aluminium extruded architectural sections of Jindal Deluxe or equivallant series having outer frames 184x47mm or nearest and 65x28 mm or nearest shutter frame all having wall thickness of 1.4 mm or above and glazing with 8mm thick toughened glass including necessary glazing bead of appropriate dimension, handle, lock, EPDM/ Neoprene gasket, ss screws, fastners etc. as per drawings and/or directions of Engineer in charge. The gap between aluminium frame and adjacent rcc/brick/stone work shall be sealed by weather silicon sealant over backer rod of approved quality. (Out to out area of the outer frame shall be measured in sqm for payment.) |
| 32 | Providing, fabricating, supplying, and installing fire doors with vision panel with outer frame made from minimum 1.5mm to 1.6mm thick glavanized steel (confrming to IS 277/BS standards), with mitred corners and securely fixed using heavy duty anchor fasterners. The door shutter shall be 46 mm thick double skin flush construction fabricated from 0.8mm to 1 mm thick glavanized steel sheets. 300mmx300mm vision panel shall be provided with 6mm clear float glass. High density mineral wool, rockwool or honeycomb core shall be used as the infill material for insulation including continuous gasket, heavy-duty hinges, locking arrangement, and all necessary fixing accessories. The door assembly shall be tested and certified to maintain the fire rating of minimum 60 mins. The exposed steel surfaces shall be finished with epoxy or PU powder coating of approved colour and shade. |
| 33 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge. With stainless steel cover plate minimum 1.25 mm thickness |
| 34 | Supply and installaiton of heavy-duty concealed hydraulic door closer, completely concealed within the top rail of the door leaf with two speed adjustment for closing speed and latching speed including all necessary mortising, heavy duty screws, channel, guide arm and all associated accessories required. |
| 35 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 36 | Wall panelling works |
| 37 | Supply and fixing of 12mm Acoustic Panels on 12mm BWP plywood partition for reducing and controlling Reverberated noise upto NRC of 0.50mm, Panel composition 100% pet to be minimum 50% Recycled PET with LOW VOC and greentag Level A certification which addresses life cycle impacts such as Toxicity.To be fixed using approved adhesives as per manufacture specifications. To have necessary cutout provisions for TV, switches, sockets etc including grooves as per the drawing. The rate shall also include the cost of providing and fixing 12mm BWP plywood (IS 710 grade) back support panelling including necessary framing, studding and backing.(Basic rate : 165/sqft) |
| 38 | Providing and fixing laminated panel work using 4 mm thick MDF board (exterior grade (Grade-I) IS:14587:1998) bonded with 1mm thick decorative laminate using hydraulic press. The panelling shall be of approved colour and shade with grooves, lines and patterns on specified area as instructed by Eic or drawing including cost of necessary hardwares, adhesives, wastages etc. The rate shall also include the cost of providing and fixing 12mm BWP plywood (IS 710 grade) back support panelling including necessary framing, studding and backing.(Basic rate of laminate : 2500/sheet) |
| 39 | Providing and fixing 1 inch half rounded well seasoned ash wood reaper finished in approved 3 coat melamine polish as per the drawing and directions by EIC. |
| 40 | Carpet flooring works |
| 41 | Supplying and laying of Nylon Carpet tiles as per following specifications and Appd. Mock-up's including necessary approved adhesives. :Brand - divine,myfloor Carpet Name / Model - As per design approvalPile Type - Multi level Patterned loopDye Method - 100% Solution DyedPile Thickness - 3 mmTile Size - 25*100 CM / 60*60 CMOunce - 18-20Yarn / Fiber - NylonBasic rate of Carpet : 190/Sft |
| 42 | Providing and fixing powder coated aluminium transition profile junction of carpet / granite / vitrified tile floor etc., including SS screws and fixing complete to include levelling the floor between SS angle and power float concrete for carpet to proper line, level and making ready to lay carpet. |
| 43 | Curtain works |
| 44 | Providing & fixing pelmet of 200mm Width and 200mm height (size may vary as per site conditions), formed of 16 mm BWP plywood (IS 710 grade) with 1 mm laminate . Pelmet to have necessary supports from the true ceiling(gypsum boxing from true ceiling to pelmet top) as per details. To have necessary grooves and to be fixed with necessary sealant as per architects instructions. Pelmet to accommodate curtains as per details. (Front length of the pelmet in running meter will measured for payment. |
| 45 | Providing and fixing heavy duty dia iron or steel curtain rod of minimum 1.5 inch diameter inside the existing pelmet including fittings, brackets, screws and all necessary accessories etc complete. |
| 46 | Supply, fabrication, and installation of manually operated sheer curtains inside the existing pelmet, in the approved style, shade, and fabric including all necessary accessories and fittings, complete in all respects. ( Area of finished fabric will be measured in sqm and paid for)Basic price of Sheer - 250(Rft-350) |
| 47 | Supply, fabrication, and installation of manually operated fabric curtains inside the existing pelmet, in the approved style, shade, and fabric, including all necessary accessories and fittings, complete in all respects. ( Area of finished fabric will be measured in sqm and paid for)Basic price of fabric - 250/sqft |
| 48 | Supply, fabrication, and installation of roller blinds of approved design, colour, and fabric, complete with all necessary operating mechanisms, brackets, fittings, and accessories, complete in all respects.Basic price of roller blind - NL-120 /SQFT, AD- 180 /SQFT |
| 49 | Storage and Furniture units |
| 50 | Chairman cabin shelf : Providing and fixing panelling and storage units of 400mm deep with skirting made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade on both side. The storage unit shall have combination of open & closed type with intermediate shelves with shutters as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. The wall panelling shall be done with 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on all exposed surfaces with necessary framing, studding and backing. This also includes providing and fxing necessary hardwares like push to latch arrangement for shutters, heavy duty auto closing-soft closing hinges, multi locks, ss tower bolts etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. (Area of the front elevation in square feet shall be measured for payment.) Approx. Size : 6000LX400MMDX3000MM HEIGHT |
| 51 | MD cabin shelf : Providing and fixing panelling and storage units of 350mm deep with skirting made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade on both side. The storage unit shall have combination of open & closed type with intermediate shelves with shutters as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. The wall panelling shall be done with 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on all exposed surfaces with necessary framing, studding and backing. This also includes providing and fxing necessary hardwares like push to latch arrangement for shutters, heavy duty auto closing-soft closing hinges, multi locks, ss tower bolts etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. (Area of the front elevation in square feet shall be measured for payment.) Approx. Size : 6000LX350MMDX3000MM HEIGHT |
| 52 | TV bottom Cabinet : Providing and fixing low height storage units of 350mm deep with legs made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade on both side. The storage unit shall have combination of open & closed type with intermediate shelves and shutters as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. This also includes providing and fxing necessary hardwares like knobe handles, heavy duty auto closing-soft closing hinges, multi locks, ss tower bolts etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. The storage unit shall be fixed with required number of M.S ready made legs for the safe positioning. (Area of the front elevation in square feet excluding the height of the legs shall be measured for payment.) SIZE : 2000LX350MMDX450MM HEIGHT |
| 53 | Open storage : Providing and fixing open type storage units of 350mm deep with skirting made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade on both side. The intermediate shelves as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. (Area of the front elevation in square feet shall be measured for payment.) Approx. Size : 1100LX350MMDX2400MM HEIGHT |
| 54 | Shelf : Providing and fixing storage units of 350mm deep with skirting made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade on both side. The storage unit shall have combination of open & closed type with intermediate shelves and shutters as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. This also includes providing and fxing necessary hardwares like knobe handles, heavy duty auto closing-soft closing hinges, multi locks, ss tower bolts etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. (Area of the front elevation in square feet shall be measured for payment.) Approx. Size : 3000LX350MMDX2400MM HEIGHT |
| 55 | Printer table : Providing and fixing low heght storage units of 350mm deep with skirting made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade on both side. The storage unit shall have combination of open & closed type with intermediate shelves and shutters as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. This also includes providing and fxing necessary hardwares like knobe handles, heavy duty auto closing-soft closing hinges, multi locks, ss tower bolts etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. (Area of the front elevation in square feet shall be measured for payment.) Approx. Size : 1800LX350MMDX1000MM HEIGHT |
| 56 | Display shelf : Providing, fabricating and fixing display shelf with glass shutters; of 400mm deep made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade. The storage unit shall have intermediate shelves as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides and shutters with 10mm thick framless toughened glass shutters. This also includes providing and fxing necessary hardwares like handles, locking facility, ss patch fittings etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. The storage unit shall be securely fixed to the wall or floor. (Area of the front elevation in square feet shall be measured for payment.) |
| 57 | Library Shelf : Providing and fixing storage units of 350mm deep with skirting made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade. The storage unit shall have combination of open & closed type with intermediate shelves and shutters as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. This also includes providing and fxing necessary hardwares like knobe handles, heavy duty auto closing-soft closing hinges, multi locks, ss tower bolts etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. (Area of the front elevation in square feet shall be measured for payment.) Approx. Size : 2100LX350MMDX2200MMHEIGHT |
| 58 | Wall hung shelf : Providing, fabricating and fixing wall hung storage units of 350mm deep made in 16mm thick BWP plywood (IS 710 grade) finished with 1mm thick decorative laminate of approved shade. The storage unit shall have combination of open & closed type with intermediate shelves and shutters as per the drawings made of 16mm thick BWP plywood (IS 710 grade) finished in 1mm thick laminate of approved shade on both sides. This also includes providing and fxing necessary hardwares like knobe handles, heavy duty auto closing-soft closing hinges, multi locks, ss tower bolts etc of approved make. The edges shall be lipped with approved edge bending tapes of minimum 2mm thick. The lamination shall be done by hydraulic press. The storage unit shall be securely fixed to the wall. (Area of the front elevation in square feet shall be measured for payment.)In Library |
| 59 | Providing, fabricating and fixing the work station table in the labrary made of well seasoned ash wood ash wood as per the drawing. Necessary storages with ashwood shutter shall be provided as per the drawing including soft-closing-auto-closing hinges, approved knobs/handles, multi-purpose locks, stainless steel tower bolts, table grommet and other fittings as approved. All the wood surfaces shall be polished with 1 coat epoxy insulator, 2 coat melamine sealer and 2 coat melamine interior matt as per manufacture recommendations. |
| 60 | Providing, fabricating, assembling and fixing reception counter table complete as per approved drawing and design, using 16 mm thick BWP plywood conforming to IS 710, finished on all exposed surfaces with 1 mm thick approved decorative laminate of selected shade and texture, including natural rattan finish as specified in the drawing. The counter shall be provided with all required storage compartments, shutters, drawers as shown in the approved drawing. The rattan finished portions shall be protected with 4 mm thick toughened clear glass, neatly fixed on the front face. The item shall include supply and fixing of all necessary hardware and accessories, including heavy-duty telescopic drawer slides/channels, soft-closing-auto-closing hinges, approved knobs/handles, multi-purpose locks, stainless steel tower bolts and other fittings required for proper functioning, all of approved make and quality. All exposed plywood edges shall be finished with minimum 2 mm thick matching PVC/ABS edge banding, neatly machine-applied and finished, and all exposed and visible surfaces, including shutters, drawer fronts, shelves and counter panels, shall be uniformly laminated with 1 mm thick approved laminate. The item shall include all necessary cutting, drilling, jointing, levelling, alignment, supports, fixing accessories, adhesives, screws, fasteners and finishing works, complete in all respects, ready for use and as directed by the Engineer-in-Charge/Architect. |
| 61 | Providing, fabricating, supplying, and fixing custom designed fixed seating in the reception area as per the approved drawings, using 16 mm thick BWP grade plywood conforming to IS 710, including all necessary framing, supports, hardware, adhesives, and accessories required for complete installation. The exposed plywood surfaces shall be finished with 1.0 mm thick decorative laminate of approved shade and make, while the seating shall be upholstered with approved D'Decor/Asian Paints fabric over cushioning comprising 32 kg/m³ density super soft polyurethane foam on the top layer and 40 kg/m³ density high-density polyurethane foam on the bottom layer, with a total cushion thickness of 100 mm. The item shall also include providing and laying polished natural pebbles in the designated areas as shown in the drawings and as directed by the Engineer-in-Charge, complete in all respects, including all labour, materials, cutting, edge finishing, polishing, wastage, transportation, and installation to achieve a finished work as per the approved drawings and specifications. |
| 62 | Providing and fixing 18mm thick WPC panels (having 0.60g/cm3 to 0.70 g/cm3 density) on the existing G.I structure as per the drawings for the wash basin cabinet including shutter with knobe handles, multilock, soft closing hinges etc complete. The visible portion of the WPC shall be finished with PU paint of approved shade. (The area of the finished WPC panels in square feet will be measured for payment). |
| 63 | Miscellaneous works Please Enable Macros to View BoQ information |
| 64 | Miscellaneous works Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysSep 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender