Tender For Comprehensive Maintenance For Petty Repair Complaint Alongwith Complaint Mgt System In The Area Of repair renovation Colony, Kandhar Line & Uri Enclave And Adjoining Area Under Ge (Central) Delhi Cantt-10
Tender Value
60 Lakhs
Estimated cost
Bid Submission
02 Oct 2026
22 days left
EMD
1.15 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Maintenance For Petty Repair Complaint Alongwith Complaint Mgt System In The Area Of repair renovation Colony, Kandhar Line & Uri Enclave And Adjoining Area Under Ge (Central) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) all as specified and directed. |
| 2 | Taking down chowkhats of frames exc 1.50 sqm but n. exc 4.0 sqm with shutters (without taking off shutters from the frames) all as specified and directed. |
| 3 | Taking down door shutters of any description exc 1 Sqm & n.exc 2 Sqm each complete all as specified and directed |
| 4 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, all as specified. |
| 5 | M&L for ceramic coloured tiles (square /recetangular) polished, area of each tiles not exc 0.36 sqm as in floors etc, over 15mm thick screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in coloured cement, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), all as specified and directed. |
| 6 | Ditto- as per item No 5 but in vertical surface as skirting, dado and risers to steps over and including10 mm thick backing coat in cement mortar 1:4 etc. |
| 7 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick joint free area of each tile exceeding 0.09 sqm but not exceeding 0.11 sqm as in floors over 15mm thick screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in coloured cement. including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), all as specified and directed. |
| 8 | Ditto- as per item No 7 but in vertical surface as skirting, dado and risers to steps over and including10 mm thick backing coat in cement mortar 1:4 etc. |
| 9 | M&L glazed ceramic coloured tiles in vertical surface 350x250x7mm / 450x350x7mm/600x300mm thick, , set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick in CM (1:4) and finished rough, complete including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), all as specified & directed.(Note - Tiling work to be done in patches including forming hole in tiles where required over making good wall surface. |
| 10 | M&L 20 to 25 mm thick pre-polished machine cut Kota stone slab as in flooring over and including 15mm thick screed bed in cement mortar 1:6, laid over cement slurry @ 3 Kg/Sqm and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge of slab complete all as specified and as directed. |
| 11 | M&L 20 to 25 mm thick pre-polished machine cut Kota stone slab as in riser or vertical surface over and including 10 mm thick rendering in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge where as specified and as directed. |
| 12 | Demolition of Brick work of stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles |
| 13 | M & L Brickwork with subclass 'B' Brick straight or curved on plan exc 6m mean radius, built in, built in cement mortar 1:6 complete including demolition of the the brick work at any position all as specified. |
| 14 | Taking down existing cement plaster or grit finished or complete removal of existing pointing and finishes including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 15 | M&L 15 mm thick Rendering in cement mortar 1:4 on faces of brick work or concrete external surfaces of wall finished even and smooth without using extra cement all as specified and directed by Engineer-in-Charge. |
| 16 | M&L 10mm thick rendering in cement mortar 1:6 on faces of brick work or concrete internal surfaces of wall finished even and smooth without using extra cement all as specified and directed by Engineer-in-Charge. |
| 17 | M&L 5 mm thick rendering in cement mortar 1:3 on concrete surfaces in ceiling, finished fair & even and smooth complete. |
| 18 | M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse stone dust) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) white cement in place of ordinary cement to be used in the work, panels with groove all around as per approved pattern or design and colour including scrubbing and washing the tip layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately). |
| 19 | M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nails to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-Charge |
| 20 | M&L for preparation of new/old plastered surfaces of wall and applying two coat apex paint over a coat of primer over one coat of putty all as sepcified and directed |
| 21 | M&L for Preparing new/old plastered surfaces of wall and applying two coats of oil bound distemper white or tinted over and including a coat of 2mm thk wall care putty on plastered surfaces preparatory to distempering complete. |
| 22 | M&L for Preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete. |
| 23 | M&L for preparation of new or old plastered surfaces of wall and applying two or more coat of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489;2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surface. |
| 24 | S&F MILD steel frames, tank staging post struts etc for doors with one or more rebates including necessary fixing lugs, 3x hinges of 100mm, lock strike plate, filling hollow of frame and hold fast fixed with plain cement concrete 1:2:4 type B0 (using 12.5mm stone aggregate) and applying two coat of synthetic enamel paint, colour as approved over a coat of redoxide etc, complete, as specified, |
| 25 | S&F Pressed steel frames of size 105mmx60mm for doors with one or more rebates including necessary fixing lugs, 3x hinges of 100mm, lock strike plate, filling hollow of frame and hold fast fixed with plain cement concrete 1:2:4 type B0 (using 12.5mm stone aggregate) and applying two coat of synthetic enamel paint, colour as approved over a coat of redoxide etc, complete, as specified, |
| 26 | S&F Flush shutters 30-35 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides with leaping and beading complete. |
| 27 | S&F for 35mm thick 2nd class hard wood plain, framed pannelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board wiyh commercial veneering on both faces. The size of rail and stile as per (IS : 1003 part-I , kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 28 | S & F for 35 mm thick factory made, 2nd class hard wood glazed and skeleton shutters open rebeated and prepared to received glass, gauzed, with out sash bar edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, size of member of shutter as per specified in SSR Part-I Section 8, clause 8.24 (a) and for door and fixed with chowkats, chemically pressure treated complete all as specified and as directed. |
| 29 | S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, fixed with stainless steel wire staples beads, tinned tacks to steel windows and wooden doors shutters complete. |
| 30 | S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and directed. |
| 31 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. |
| 32 | S&F Factory Made double rebated extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65 x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made |
| 33 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as specified and directed. |
| 34 | M & L for applying two coat of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth complete all as specified and as directed. |
| 35 | S&F 100 mm long mild steel butt hinges, cold rolled, medium weight complete all as specified and directed. |
| 36 | S&F for 125mm long stainless steel tower bolt of extruded section complete all as specified and directed. |
| 37 | S&F 150mm long stainless steel handles, cast type complete all as specified and directed. |
| 38 | S&F 300mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed. |
| 39 | S&F Stainless Steel Cromium Plated tubing of 25 mm dia curtain rod fancy type including fancy type CP brabs brackets (wall to wall or flush to wall) with finials or end caps decorative type as approved by GE for securing to curtain rod to wall in position, fixed in repair complete. |
| 40 | M&L for disconnecting existing PVC tanks, of capacity exc 250 ltr and nexc 500 ltr and setting aside (or lowering if required) for roof treatment, etc and hoisting if required reconnecting and refixing in postion |
| 41 | M&L for disconnecting existing PVC tanks, of capacity exc 500 ltr and nexc 1000 ltr and setting aside (or lowering if required) for roof treatment, etc and hoisting if required reconnecting and refixing in postion |
| 42 | Demolition Bricks (laid flat or on edge) or brick tiles in floors, roof, channels, kerbs, aprons, etc. (each layer all as specified and directed. |
| 43 | Demolition Mud in roofs, any thickness, including plastering and lapping (whether full thickness removed or only a part thereof) all as specified and directed. |
| 44 | Removing soil excavated material exc. 1.5Km but n exc 5km and depositing where directed at above the starting point all as specified and directed. |
| 45 | M&L for cement concrete 1:2:4 type B1 (using 12.5mm graded stone aggregate) on roof padding surface finished even and smooth without using extra cement complete all as spd & directed. |
| 46 | M&L providing and applying the plaster with single component ready to use repair mortar (SMART CARE REPAIR MORTAR or equivalent) capable of applying 15mm average thickness in single layer and finishing with trowel with a bond coat: SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area mixed with specified portion of AP SMARTCARE or equivalent Repair Polymer, complete all as specified land as directed. |
| 47 | M&L providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajas in multiple coats @2.0 litre/sqm. Primary [coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge.Notes: (1) The work shall be executed through authorised applicator of manufacturer only.(2) Authrised Applicator shall be approved by GE before starting of work.(3) All materials shall be procured directly form manufacturer. The purchase voucher shall be produced to the Engineer-in-Charge for his verification of material.Engineer-in-Charge shall deface the original purchase vouchers.(4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor's dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer. |
| 48 | S & F rotational moulded 500 lit capacity polythelene water storage tanks ( cylindrical verticle with closed top) hoisted and fixed in position all as specified |
| 49 | S & F rotational moulded 1000 lit capacity polythelene water storage tanks ( cylindrical verticle with closed top) hoisted and fixed in position all as specified |
| 50 | S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors including taking up or down steel tubing and connections complete. |
| 51 | S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors including taking up or down steel tubing and connections complete. |
| 52 | Supply and laying of 20mm outer dia of CPVC pipe SDR 11 and plain CPVC SDR 11 fittings on wall/ceiling or laying in floors complete including brass CPVC fittings (i.e elbow, Tee, MTA/MBTA,FTA/FBTA, Tank adaptor, Union, etc suitable for 15mm bore bath fittings). (Note- length of pipe with fittings to be measured for payment, no extra payment should be made for fittings). |
| 53 | S & F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete. |
| 54 | S & F in repair float valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic wall, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210gms), complete. |
| 55 | Cutting chases in brick walls, pinning in, making good any thickness up to wall tile to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting exceeding 20cm girth complete. |
| 56 | S & F in repair Brass CP wall mixer for mixing hot & cold water screwed down high pressure, with all necessary fittings, screwed for pipe 15 mm bore with all fittings complete. |
| 57 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or in floor 75mm bore including demolition/taking down PVC/ drain/Rain water pipe complete. |
| 58 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm bore including demolition/taking down PVC/ drain/Rain water pipe complete. |
| 59 | S&F PVC (SWR) bends any radius, 75 mm bore, complete. |
| 60 | S&F PVC (SWR) bends in repair with access door any radius, 75 mm bore, complete. |
| 61 | S&F PVC (SWR) bends any radius, 110 mm bore, complete. |
| 62 | S&F PVC (SWR) bends with access door any radius, 110 mm bore, complete. |
| 63 | S&F PVC (SWR) vent cowl, 75 mm bore complete. |
| 64 | S & F in repair Stainless steel plate rack (utensil rack) of size (600 mm x 750 mm) and depth 300 mm made with 0.55 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts complete. |
| 65 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 66 | S & F in repair Soap dish disc (oval) type, mild steel chromium plated of approximate size 100 x 50 x 10 mm, complete. |
| 67 | S & F in repair sheet Glass shelf assembly consisting up to 4 mm thick sheet glass self 12 cm wide with chromium plated bracket guard and railing 60 cm long. |
| 68 | S&F in repair 75 mm PVC (SWR) floor trap, plain with grating doom including jointing with solvent cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate mix with WPC complete all as specified and as directed. |
| 69 | S & F in repair stainless steel sink with drainage board, made out of 1.00 mm thick sheet with plug, washers, waste pipe, cast iron cantilever brackets, connecting union over all size 915 mm X 460 mm with bowl size 410 mm x 330mm x 160 mm complete. |
| 70 | S & F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete. |
| 71 | S & F in repair Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete. |
| 72 | S & F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15 mm bore complete. |
| 73 | S&Fixed in repair 90 to 125 mm size chromium plated shower rose with siwel joint suitable for 15 mm bore GI pipes comlete all as directed.. |
| 74 | S&F in repair 10 litre capacity PVC low level flushing cistern ‘ white’ with inlet, float valve including bracket with 32mm dia PVC waste/flush bend pipe appx 600 mm long complete. |
| 75 | S & F in repair PVC connection 600mm long and15 mm dia with brass fly nut at both ends complete. |
| 76 | S&F in repair Vitreous china wash down water closet pan including trap, white including fixing bolts, flushing cistern and flush pipe connection to trap and to flushing pipe in bend cluding provn of cement concrete beading complete all as specified and directed. |
| 77 | S & F vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete. |
| 78 | Supply only EWC Seat cover white colour as approved of PVC closed pattern with flat bottom and mild steel lchromium plated or aluminised hinging device complete all as specified and directed. |
| 79 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 80 | S&F in repair CP Crome Jet for 15 mm dia with pipe crome plated 1.25 Mtr long flexible tube and complete all as specified and directed. |
| 81 | S&F in repair Chromium plated brass angle valve concelled type for 15mm bore pipe, fixed in repairs complete all as specified and directed. |
| 82 | S&F in repair sheet glass ordinary quality, 4-5 mm thick and glazing with aluminium glazing clip, rubber gasket etc in aluminium window any type in square complete all as specified and directed. |
| 83 | S & F in repair Stainless steel, wire cloth 0.56 mm nominal dia of wire, and average width of aperature 1.18mm and fixed to steel or wooden window or doors with necessary fixing arrangement complete all as specified. |
| 84 | Mild steel conforming to Fe 410-0 or Fe 310-0 in framed work such as grills, gratings, door frame etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete. |
| 85 | S&F Mild steel, plain, black sheet of 1.60 mm thick in wall cladding steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up mitred angles etc as required |
| 86 | Labour for repair in carpenter door, kitchen cupboard window wiremesh etc related to carpenter up to 9 story bldg with using safety belt or jhula work included repair in building etc |
| 87 | Labour for repair in plumbing shaft / duct up to 9 story bldg with using safety belt or jhula work included repair to PVC pipe incl PVC fittings, fixing of MS clamp / bracket, RCC Jali, MS ring / foot rest etc |
| 88 | M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 89 | M&L for two coats of synthetic enamel paint on old steel painted surfaces including preparation of surfaces of any description not otherwise descriped over 10 cm width or grith complete all as specified and directed. Please Enable Macros to View BoQ information |
| 90 | M&L for two coats of synthetic enamel paint on old steel painted surfaces including preparation of surfaces of any description not otherwise descriped over 10 cm width or grith complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender