Tender For Construction of Type-Ll-4 Nos. Quarter At Kamle.
Tender Value
1.36 Crore
Estimated cost
Bid Submission
10 Sep 2026
5 days left
EMD
1.36 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Lower Subansiri → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction of Type-Ll-4 Nos. Quarter At Kamle.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in rough excavation,banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with 1/2 tonne roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonne and dressing up in embankd banks, marginal banks and guide banks filling up grounddepressions lead upto 50mm and lift upto 1.50m. for site development A). Ordinary Soil @ 70% |
| 2 | Hard Soil/Ordinary Rock |
| 3 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 4 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 5 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. (Foundation) |
| 6 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.(Wall) |
| 7 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 8 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone shingle 20 mm nominal size). |
| 9 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 10 | Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with M20 (1cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 11 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 12 | Providing reinforced cement concrete eaves board 25 mm thick and 15 cm to 30 cm wide inM 20 mix (1 cement : 1.5 coarse sand : 3 stone aggregate 10 mm nominal size) up to floor two level including finishing and plastering with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm on exposed surfaces to give smooth and even surface, centring and shuttering but excluding cost of reinforcement. |
| 13 | Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:3 (1 cement : 3 fine sand). |
| 14 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 15 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc, including welding,grinding, buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accesories & stainless steel dash fasteners, stainless steel bolts etc, of required size, on the top of the floor or the side of waist slab with suitbale arrangements as per approval of Engineer- in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accesories such as nuts, bolts, fasteners etc.) |
| 16 | Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.b) Ornamental grill. |
| 17 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. (Foundation) |
| 18 | Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 (cement : 2 coarse sand : 4 stone aggregate 10 mm nominal size) |
| 19 | Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. a)50 mm thick |
| 20 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including Grouting the joints with white cement and matching pigments etc, complete. d). Size of tiles 500 x 500 mm |
| 21 | Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: b) Medium shade using approximately 50% white cement and 50% ordinary cement. |
| 22 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 23 | Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete. |
| 24 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 25 | Providing and fixing plain timber Door and steel angle 45x45x5mm fasten with steel strip of 25mmx4mm, including steel chowkat and necessary iron fittings and screws including painting with smoke grey paint two or more coat above priming coat. |
| 26 | Providing and fixing Glazed window in steel frame of angle 25mmx 25mmx4mm in frame of 30x30x4mm fastened with bead/putty including steel chowkhat ,Gril& necessary fittings & screws as per design and drawing including painting with Red Oxide paints. |
| 27 | Centring and shuttering including strutting, propping etc and removal of form work for :- a) Foundation, footings, bases of columns etc. and mass concrete. =2*(1.4+1.4)=5.6 mtr |
| 28 | b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 29 | c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).Timber used 8 times |
| 30 | d) Lintels, beams, girders, bressumers and cantilevers etc.Timber used 8 times |
| 31 | Main Column |
| 32 | 12 mm cement plaster 1 : 3 (1 cement : 3 fine sand). |
| 33 | Neat cement punning. |
| 34 | Finishing walls with wall putty of approved brand and manufactured and required shade on new work (three or more coats) to give and even shade. |
| 35 | Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. |
| 36 | Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.(Outside & inside wall as Direction by Engineer In charge) |
| 37 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete. |
| 38 | Applying priming coat with ready mixed primer of approved brand and manufacture on steel work. |
| 39 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade. |
| 40 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade. |
| 41 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone shingle 20 mm nominal size). |
| 42 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 43 | Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with M20 (1cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 44 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 45 | Providing reinforced cement concrete eaves board 25 mm thick and 15 cm to 30 cm wide inM 20 mix (1 cement : 1.5 coarse sand : 3 stone aggregate 10 mm nominal size) up to floor two level including finishing and plastering with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm on exposed surfaces to give smooth and even surface, centring and shuttering but excluding cost of reinforcement. |
| 46 | Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:3 (1 cement : 3 fine sand). |
| 47 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 48 | Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. (b) Ornamental Grill. |
| 49 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including Grouting the joints with white cement and matching pigments etc, complete. d). Size of tiles 500x 500 mm |
| 50 | Providing and fixing plain timber Door and steel angle 45x45x5mm fasten with steel strip of 25mmx4mm, including steel chowkat and necessary iron fittings and screws including painting with smoke grey paint two or more coat above priming coat. |
| 51 | Providing and fixing Glazed window in steel frame of angle 45mmx 45mmx5mm in frame of 30x30x4mm fastened with bead/putty including steel chowkhat ,Gril& necessary fittings & screws as per design and drawing including painting with Red Oxide paints. |
| 52 | Centring and shuttering including strutting, propping etc and removal of form work for :- c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).Timber used 8 times |
| 53 | d) Lintels, beams, girders, bressumers and cantilevers etc.Timber used 8 times |
| 54 | e) Column, pillars, posts and struts etc. |
| 55 | 12 mm cement plaster 1 : 3 (1 cement : 3 fine sand). |
| 56 | Finishing walls with wall putty of approved brand and manufactured and required shade on new work (three or more coats) to give and even shade. |
| 57 | Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. |
| 58 | Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.(Outside & inside wall as Direction by Engineer In charge) |
| 59 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete. |
| 60 | Applying priming coat with ready mixed primer of approved brand and manufacture on steel work. |
| 61 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade. |
| 62 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade. |
| 63 | Construction of Septic Tank 3.8 mx2.8m x1.8m as per complete standard drawing & design. |
| 64 | Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design. |
| 65 | Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. a) Inside size 90 X 80 cm and 45 X 45 cm deep including CI cover with frame (light duty) 455 X 610 mm internal dimensions total weight of cover and frame to be not less than 38Kg (weight of cover and frame not less than 38kg, weight of cover 23 kg and weight of frame 15kg). |
| 66 | Providing and fixing white vitreous china water closet squating pan (Indian types WC Pan) size 580 mm with 100 mm and sand iron P or S Trap, 12.5 litre high level CI Flushing cistern (of approved make) with fittings RS or CI Brackets,32 mm dia galvanized steel telescopic flush pipe with fittings and clamps, 20 mm GI overflow pipe with specials and mosquito proof coupling of appeoved municipal design and GI chain and pull complete including painting of cistern and fitting, cutting making good the walls and floors where required. a). Long pan patten WC Pan |
| 67 | Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.(250mmX130mmx30mm) |
| 68 | Providing and fixing 12.5 litres high level CI flushing cistern of approved make with intergral fittings such as ball valve, bell, lever, GI chain and pull Complete. |
| 69 | Providing and fixing in position 32 mm dia galvanized steel telescopic flush pipe complete including cutting and making good the walls and floors. |
| 70 | Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.Size 75mm Dia |
| 71 | Providing and fixing 100 mm sand CI 'P' or 'S' trap. |
| 72 | Providing and fixing best quality PVC Elbow 110mm. |
| 73 | Best quality PVC Connecting Pipe 110mm dia 30cm length. |
| 74 | Terminal Guard with Clamp(PVC) |
| 75 | Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc.b) 100 mm diameter |
| 76 | Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 100 mm dia SW pipes |
| 77 | Providing fixing and laying of PVC 110mm for sewage under ground and filled with cc 1:12 ( 1 Cement : 12 Mixed sand Shingles) |
| 78 | Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required. a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality. |
| 79 | Providing and fixing CP brass waste for wash basin and sinks.( From wash basin shink at every floor to drain at ground including all fittings.) a)32 mm dia. |
| 80 | Providing and fixing kitchen sink including making all connection excluding cost of fittings.(White vitreous china sink size(600 x 450 x 150) |
| 81 | Construction of cc juntion box 50cm x 50cm x 50cm (overall) at the spacing of 6m distance alobg Pvc pipe line or at every junctoin including Rcc cover complete |
| 82 | Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers. |
| 83 | Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls. a)15 mm nominal bore |
| 84 | b) 20 mm nominal bore(internal work). |
| 85 | b) 20 mm nominal bore(External work). |
| 86 | c) 25 mm nominal bore(Externall work). |
| 87 | Providing and fixing brass stop cock of approved quality.15 mm nominal bore |
| 88 | a) 20 mm nominal bore(Internal) |
| 89 | b) 25 mm nominal bore(external) |
| 90 | Providing and fixing brass bib cock of approved quality.a)15 mm nominal bore |
| 91 | providing and fixing in position sintex for water supply |
| 92 | Providing ,Fixing ,commissioning & testing of 1 H.P. 1 Phase pump(SWJ 1 ) including control Panel and all accesories or as directed by Engg. i/c |
| 93 | Construction of Under Ground Water Tank of clear dimension (Size 4.5 m x 3 m x 2 m) with wall thickness of 230mm after plaster including GI Fittings and RCC Slab or as Directed by the engineer in charge. |
| 94 | Manufacturing and supply of wooden coat made of A class Timber including,moisquito stand and finishing with varnish of approved brand or as may be directed by Engineer incharge. (Medium size.) |
| 95 | Manufacturing and supply of wooden coat made of A class Timber including,moisquito stand and finishing with varnish of approved brand or as may be directed by Engineer incharge. (Single size.) |
| 96 | PVC Chair of best quality. |
| 97 | PVC or Wooden Dinning Table of best quality. |
| 98 | Dinning Chair of best quality. |
| 99 | Filter 30 ltr capacity. |
| 100 | Transportation charges for carrying of building materials:- a) Cement |
| 101 | b) Steel |
| 102 | c) Bricks |
| 103 | d) Aggregate |
| 104 | e) Sand Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysSep 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender