Tender For Special Repair To Old Rusted Pipeline, Valve Pit,Sluice Valves And Provn Of Fol Dump At Sigar Mil Stn Under Ge 872 Ews
Tender Value
40.80 Lakhs
Estimated cost
Bid Submission
23 Sep 2026
16 days left
EMD
82000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Siang → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Old Rusted Pipeline, Valve Pit,Sluice Valves And Provn Of Fol Dump At Sigar Mil Stn Under Ge 872 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 2 | Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, cable etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed. |
| 4 | Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 5 | M & L gravel filling in floors or pavings, laid in layers n exc. 15 cm thick, spread,levelled, and blinded with earth and rammed including watering all as specified & directed. |
| 6 | M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 7 | M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed. |
| 8 | M & L Reinforced Cement Concrete 1:2:4, Type B-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed.(Note : Reinforcement will be measured & paid seperately) |
| 9 | &L for 40mm thick damp proff course to horizontal or vertical surfaces in cement concrete 1:2:4, type B-0 using 12.5mm graded stone aggregate including necessary formwork over and including 50 micron thick polythene film, laid on a coat of bitumen primer @ 0.30 to 0.50 Kg per Sqm and applying a coat of blown type bitumen evenly at the rate of 1.50 Kg per square metre and blinding with clean dry sand @ 0.05 Cum per Sqm complete all as specified and directed. |
| 10 | M & L for Pre-cast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), block masonry with solid blocks of size 300x200x200mm or 300x200x100mm, having compressive strength of not less than 100 Kg/Sq Cm (As per IS-2185) exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed. |
| 11 | M&L Use and waste for Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed. |
| 12 | S&F steel window with side hung shutter including projection type hinges with steel handles, and steel peg stay with glazing bars dovetailed or welded incl taking out old window complete all as specified. |
| 13 | S&F 4.00mm thick sheet glass, selected quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 14 | S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 15 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screw complete all as specified and directed. |
| 16 | M&L Mild Steel Work in Tubular Trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conform-ing to IS:1161-1979 grade St.-240, complete all as specified and as directed. |
| 17 | M & L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete(FE290(Grade E-165) all as specified & directed. |
| 18 | S & F 0.80 mm Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified & directed. |
| 19 | S & F high strength TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. |
| 20 | S & F high strength Mild steel TMT bars 5mm dia and over upto and including 8mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed. |
| 21 | M & L for 40 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in flooring, etc and finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 22 | M & L 75 mm thick cement concrete 1:2:4 type B -2( using 40 mm graded stone aggregate) using extra cement finishing cement concrete surface even and smooth complete all asspecified & directed. |
| 23 | M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed. |
| 24 | M&L Rendering 15mm thick in Cement Mortar 1:4 on other than fair faces of Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and Smooth without using Extra Cement complete all as specified and as directed. |
| 25 | M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and smooth without using extra cement complete all as specified and as directed. |
| 26 | S & F water proofing compound (as approved), conforming to IS : 2645-2003, complete all as specified & directed. |
| 27 | M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed. |
| 28 | M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed. |
| 29 | M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed. |
| 30 | Supply & fix in repair 3- layer PP-R Polypropylene random copolymer pipes having 25 mm outer diameter with SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain polypropylene random fittings as per site requirement i.e. tees, bends, elbow, reducer, enlarger, union, socket etc laid in trenches complete in all respect as specified or directed.Note : (i) Necessary earth work for laying in trench/underground will be measured and paid separately.(ii) Cost of T&P and any type of PP-R fittings required at site for branch connections/fixing of water pipe line deemed to be included in the unit rate quoted by the contractor. |
| 31 | Supply & fix in repair 3- layer PP-R Polypropylene random copolymer pipes having 75 mm outer diameter with SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain polypropylene random fittings as per site requirement i.e. tees, bends, elbow, reducer, enlarger, union, socket etc laid in trenches complete in all respect as specified or directed.Note : (i) Necessary earth work for laying in trench/underground will be measured and paid separately.(ii) Cost of T&P and any type of PP-R fittings required at site for branch connections/fixing of water pipe line deemed to be included in the unit rate quoted by the contractor. |
| 32 | M&L for Making connection of PP-R distribution branch with PP-R/GI mains of upto 75 mm size by providing and fixing tee including cutting and making fusion joint etc.complete all as specified & directed. |
| 33 | S&F Cast Iron sluice valve 65 mm bore dia, long body type, both ends flanged & drilled all as per ISI standard (IS:14846-2000 & Class PN 1.6) having cast iron operating hand wheel, brass spindle, cheek nuts and sliding gate having mild steel body, suitable bolts, washers & nuts complete in all respect including testing against any leakage/defect/operating mulfunctioning if any by taking out/down unserviceable sluice valve complete all as specified and as directed. Old unserviceable sluice valve be kept in safe custody for further disposal or to issue under schedule of credit to the contractor. Note : (i) Contractor must visit the site to check the noof holes, width of the existing sluice valve, so that purchase new one can be fixed properly without any addition / alteration in water supply network.(ii) Cost of minor spares such as rubber packin material, cotton waste etc deemed to be included in the quoted unit rates. Please Enable Macros to View BoQ information |
| 34 | S&F Cast Iron sluice valve 65 mm bore dia, long body type, both ends flanged & drilled all as per ISI standard (IS:14846-2000 & Class PN 1.6) having cast iron operating hand wheel, brass spindle, cheek nuts and sliding gate having mild steel body, suitable bolts, washers & nuts complete in all respect including testing against any leakage/defect/operating mulfunctioning if any by taking out/down unserviceable sluice valve complete all as specified and as directed. Old unserviceable sluice valve be kept in safe custody for further disposal or to issue under schedule of credit to the contractor. Note : (i) Contractor must visit the site to check the noof holes, width of the existing sluice valve, so that purchase new one can be fixed properly without any addition / alteration in water supply network.(ii) Cost of minor spares such as rubber packin material, cotton waste etc deemed to be included in the quoted unit rates. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysSep 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender