Tender For Special Repair To Boundary Wall Under Age B/R-I At Mil Stn Yol
Tender Value
43.70 Lakhs
Estimated cost
Bid Submission
26 Sep 2026
18 days left
EMD
87400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Boundary Wall Under Age B/R-I At Mil Stn Yol
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of stones or brick masonry or block walling, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete including removal of debris to a distance exc 1.5 km but n.exc 2 Km, complete all as specified and as directed. |
| 2 | PCC 1:3:6 type C-2, using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. |
| 3 | Reinforced cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns etc; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. |
| 4 | Reinforced cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts, complete all as specified and directed. |
| 5 | Reinforced cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed. |
| 6 | Formwork to sides of concrete foundations, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter, rough finished surfaces of concrete flat, complete all as specifed and directed. |
| 7 | Form work to sides of pillars, posts, struts, pier, columns, square, rectangular or polygonal rough finished surface of concrete, complete all as specified and directed. |
| 8 | Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc.; to rough finished surface of concrete flat complete all as specified and as directed. |
| 9 | Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified. |
| 10 | All as item No. 9.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders. |
| 11 | Brick work with fly ash bricks straight or curve on plan exceeding 6m radius, built in CM 1:4 complete all as specified and directed by Engr-in-Charge |
| 12 | All as item No. 11.00 above but except bricks |
| 13 | Walling of random rubble stone masonry , uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and directed. |
| 14 | Rendering cement plaster 15mm thick in cement mortar 1:4 in two layers on brick surffaces or stone masonry surfaces, finished the surface even and smooth without using extra cement, mixed with WPC as per manufacture instruction, complete all as specified and directed.Note : Water proofing compound shall be measured and paid for separately as Supply only . |
| 15 | Supply only integral water proofing compound . |
| 16 | Preparation of newly plastered wall surfaces and finishing walls with acrylic smooth exterior paint of required shade two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and as directed by Engr-in-Charge |
| 17 | Mild steel work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 18 | Preparation of new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-Charge. |
| 19 | Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed by Engr-in-Charge. |
| 20 | Plain cement concrete 1:2:4, type B- 0 (using 12.50mm graded crushed stone aggragate), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and holdfast and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs n, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including use of form work complete all as specified and directed. |
| 21 | Punched tape concertina coil as per latest IS 6745-1972 with galvanised coating and punched type material as per IS deep drawn quality with galvanised coating having medium barbs fixed in position and secured to fence posts/straining Y- arm stretched to a length so as to achieve 600mm dia as in fencing including fixing with special galvanised fasteners such as J clips, C clips, U clips fixed at any height of security fence including necessary scaffolding complete all as directed.Size of Coil: 600mm dia and 2.5mm core wire thick.Type of strip: Heavy galvanised conforming to IS 1730 (1989).Type of core wire: Heavy galvanised conforming to IS 280-2006. Zinc coating to strip : 200GSM/SqmmZinc coating to line wire: 18 micronsTensile strength of wire: 1620 N/Sqmm.Weight: 9.00 Kg/per coil (± 5% tolerance).Stretchable length of each coil: 6m. Type of clip: Steel grade 'A' as per IS 2060 finished hot dip galvanised 20 micron.Steel strip: Width -19mm and thickness 0.5mm |
| 22 | Deduction to be made from BOQ for Sch 'A' Part-II (Schedule of credit) Note: Tenderers shall not quote for this schedule. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysSep 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender