Tender For Upgradation Of Existing Medical College & Teaching Hospital, Existing 100 Ug Seats Upgradation To 250 Ug Seats To 200 Pg Seats & 16 Post Pg Seats To 50 Post Pg Seats Along With Other Allied Infrastructure & Services (Part-2) Under Proposed
Tender Value
Ref. Documents
Estimated cost
Bid Submission
24 Sep 2026
21 days left
EMD
86.21 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhanbad → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Upgradation Of Existing Medical College & Teaching Hospital, Existing 100 Ug Seats Upgradation To 250 Ug Seats To 200 Pg Seats & 16 Post Pg Seats To 50 Post Pg Seats Along With Other Allied Infrastructure & Services (Part-2) Under Proposed Snmmch College & Teaching Hospital, Dhanbad : Holistic Augmentation & Redevelopment At Dhanbad
BOQ
| Sl. No. | Item Description |
| 1 | Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I |
| 2 | Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B) |
| 3 | Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume). |
| 4 | Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge |
| 5 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor. With Chlorpyriphos EC 20% with 1% concentration |
| 6 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 7 | CONCRETE WORK |
| 8 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 9 | Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size) |
| 10 | R C C WORK |
| 11 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of layinh but excluding the cost of centering ,shuttering finishing and reinforcement including admixtures in recommended proportions as per IS : 9103 to accelerate rated srtting of concrete, improve workability without impaiting strenth and durability as per direction of engineer in charge (note :- Cement content considered in this item is 330 kg/cum excess/ less cement used as per design mix is payable/ recoverable seperataly ). |
| 12 | All works uptp plinth level |
| 13 | All works above plinth level upto floor V level |
| 14 | Add for using extra cement in the items of design mix over and above the specified cement content therein. |
| 15 | Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. |
| 16 | Providing Tor steel reinforcement as per approved design & drawing |
| 17 | Providing Tor steel reinforcement of 8mm. dia.TMT rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 18 | Providing Tor steel reinforcement of 10mm,28/32mm dia. TMT rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 19 | Providing Tor steel reinforcement of 12/16mm. & 20/25mm. dia. TMT rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 20 | Centering and shutteing including struting, propping etc and removal of form for Foundations, footings, bases for columns, etc for mass concrete |
| 21 | Centering and shutteing including struting, propping etc and removal of form for Suspended floors, roof , landings , balconies and access platform |
| 22 | Centering and shutteing including struting, propping etc and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 23 | Centering and shutteing including struting, propping etc and removal of form for Columns, Pillars, Piers, abutments, Posts and struts |
| 24 | BRICK WORK |
| 25 | providing designation 75 B brickwork in C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l. |
| 26 | Providing designation 75A brickwork in CM (1:3) in superstructure with approved quality of clean coarse sand of FM 2 to 2,5 including providing 10mm thick mortar joints , cost of screening, materials, scaffolding, raking out joints to 15mm depth curing, taxes and royalty all complete as building specification and direction of E/I |
| 27 | providing designation 75 B brickwork in C M ('1 :6 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l. |
| 28 | Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9\\"x4.5\\"x3\\") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 29 | Providing designation 112 mm thick reinforced designation 100 A brick work vuith fly ash lirne brick (FLAG)confirming to lS 12894-1990 (9\\"x4'5\\"x3\\" ) in C.M. ( 1 . 4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials,n caffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specificationand direction of E/|. |
| 30 | Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary |
| 31 | WOOD WORK |
| 32 | Supplying, fiiting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors windows skylights fanlights and C/W celetial window opening including wedge over all clamps complete including application of two coats of wood preservative of approved quility onthe surface buttling walls and lintels all complete as per building specification anddirection of E/I. |
| 33 | Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutter door and windows with black board core blended with high quality phenol formal clehydes synihetic resin both side commercial veneered of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l. |
| 34 | Supplying fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter door and windows with black board core blended with high quality phenol formal clehydes synihetic resin both side commercial veneered of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l. |
| 35 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.0 mm thick |
| 36 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : |
| 37 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 38 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 39 | Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating not less than 120 gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed Door Shutters. The frame shall be filled with mineral wool Insulation having density minimum 96Kg/sqm. The frame will have a provision of G.I. anchor fastners 14 nos (5 each on vertical style & 4 on horizontal style of size M10 x 80) suitable for fixing in the opening along with factory made template for SS ball bearing hinges of size 100x89x3 mm for fixing of fire rated glazed shutter. The frame shall be finished with an approved fire resistant primer or powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- Charge. (Cost of SS ball bearing hinges is excluded). |
| 40 | Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (paneling to be paid for separately). |
| 41 | STEEL WORK |
| 42 | Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. |
| 43 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with carbon steel galvanised dash fastenerof required dia and size (to be paid for separately |
| 44 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 45 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 46 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 47 | Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer. Using M.S. angle 40x40x6 mm for diagonal braces |
| 48 | Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. |
| 49 | FLOORING WORK |
| 50 | providing and laying, Doublecharge vitrified floor tiles in different sizes (thickness to be specified by lhe manufacturer) with water absorption less than 0.08% and conforming to lS 15622/ISO 13009 of approved make in all cotours and shades, laid on 20mm thick cement mortar 1 4 (1 cement:4 coarse sand) jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of tile 600x600 mm |
| 51 | Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 SQM |
| 52 | Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 53 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 54 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 55 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1 : 3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specificaton and directon and E/I. |
| 56 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 :: 4 (1 cement: 4 coarse sand): 25 mm thick |
| 57 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 58 | Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand): Medium shade pigment using 50% white cement, 50%ordinary cement |
| 59 | ROOFING & WATER PROOFING WORK |
| 60 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase |
| 61 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 62 | Roof/Terrace Water proofing: |
| 63 | Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :- |
| 64 | (a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete. |
| 65 | (b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured.\\" |
| 66 | (c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl.\\" Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal |
| 67 | (d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be charrmfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface slrould be packed properly with rich concrete and the peripheral mouih to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose ofrreasurement the entire treated surface will be measured.\\" |
| 68 | (e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years. |
| 69 | Covering of treated surface wrth PCC :- Providing 50mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr |
| 70 | Providing and mixing Liquid lntergral water proofing compound in Conctrete or plaster as per rnanufacturer specificatioqand as per cjirection of Eng - in Charge Brand- Sika Plastocrate plus, MYK proof WP 1 0, Fosroc-Cc.rnplast X4211 C, Dr fixit Pidiproof LW+ or Equivalent |
| 71 | Providing and filling of 6 mm groove between 50mm PCC panels with 6 mm thick deep thermocol strip and filling the rest 25mm with polysulphide sealant (poring grade)as per drawing and technical specification and direction of E in charge (with 18 % GST ). Brand:- sika - polysulshide,fosroc- thioflex 600, dr fixit pidi seal PS (42P) ,MYK seal PS or euivalent. |
| 72 | Toilet/Kitchen Water proofing: |
| 73 | 1) Surface preparation by grinding machine, cleaning , crack filling etc. complete |
| 74 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : |
| 75 | (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. |
| 76 | (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry |
| 77 | FINISHING WORK |
| 78 | Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 79 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 80 | Providing 12 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l. |
| 81 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper apllyingh putty whenever required scaffolding washing of floors and taxes all complete as per building specfication and direction Of E/I. |
| 82 | Providing two coats of snowcem of approved shade and make over old surface including washing cleaning and preparing the walls, scaffolding , curing and taxes all complete as per building specification and direction of E/I. |
| 83 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 84 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 85 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 86 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. |
| 87 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface |
| 88 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l. |
| 89 | ALUMINIUM WORK |
| 90 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid .in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 91 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 92 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 93 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design(b) Providing, fabricating and supplying and fixing panels of aluminiumcomposite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall becoil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot DipGalvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of allmaterial & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 94 | Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600 Upto 10 mm depth and 10 mm width |
| 95 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading |
| 96 | Providing and fixing of 16 Passenger Lift/ 1088Kgs / 1.25 Speed / 13Floors / 13 Stops / Stainless Steel (1.5MM) car cabin |
| 97 | Providing and fixing of 20 Passenger Lift/ 1360 / 1.25 Speed / 13 Floors / 13 Stops / Stainless Steel (1.5MM) car cabin |
| 98 | CARRAIGE OF MATERIALS |
| 99 | SAND (UPTO 10KM LEAD) |
| 100 | CHIPS (UPTO 22KM LEAD) |
| 101 | BRICKS (UPTO 8KM LEAD) |
| 102 | ELECTRICAL WORK |
| 103 | Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required. Group C |
| 104 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C |
| 105 | Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required. |
| 106 | Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 107 | Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required |
| 108 | 2x2.5 sq mm + 1x2.5 sq mm earth wire |
| 109 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire. |
| 110 | 2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire |
| 111 | 4 x 10 sq.mm. + 2 x 6 sq.mm. Earth wire |
| 112 | 4 x 16 sq.mm. + 2 x 6 sq.mm. Earth wire |
| 113 | S/F light plug point Modular Type Accessories :- |
| 114 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections painting etc. as required. (For light plugs to be used in non residential buildings). |
| 115 | S/F power plug point modular Type Accessories :- |
| 116 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections painting etc. as required. (For light plugs to be used in non residential buildings). |
| 117 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 118 | Rewiring for light point/fan point/exhaust fan point/call bell point 1.5 sqmm FR PVC insulated copper conductor singe core cable in existing surface/recessed steel/PVC conduit including dismantling as required Group B |
| 119 | Supply and drawing following size of FR PVC insulated copper conductor single core cable in existing surface/recess steel/PVC conduit including dismantling as required. |
| 120 | 3 x 2.5 sqmm |
| 121 | 3 x 4 sqmm |
| 122 | DISTRIBUTION BOARDS & MCB's |
| 123 | Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA \\"C\\" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required. |
| 124 | 6/32 amps, Single pole |
| 125 | 40 amps DP |
| 126 | 50/63 amps, TPN |
| 127 | Supplying and fixing Single pole blanking plate in the existing MCB DB complete etc. as required. |
| 128 | Supplying and fixing following ways, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 129 | 6 Way (4 + 18), Double Door Horizontal Type |
| 130 | 8 Way (4 + 24), Double Door Horizontal Type |
| 131 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 132 | 12 way , Double door |
| 133 | S/F DP MCB Isolator |
| 134 | Supplying and fixing following Rating, Double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 40 Amps |
| 135 | S/F 4P MCB Isolator |
| 136 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 63 Amps |
| 137 | S/F DP (RCCB) |
| 138 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 40 Amps |
| 139 | TELEPHONE, TELEVISION & DATA SYSTEM (socket,wiring & conduting only) |
| 140 | S/F MODULAR BOXES, BASE & COVER PLATE :- |
| 141 | Supplying and Fixing Following Size/ Modules, GI Box Alongwith Modular Base & Cover Plate for Modular Switches in Recess etc. as Required. 1 or 2 Module (78mm x 78mm x 45mm) |
| 142 | S/F MODULAR TYPE SWITCH / SOCKET :- |
| 143 | Supplying and Fixing Following Modular Switch/ Socket on The Existing Modular plate & Switch Box including connections But Excluding Modular Plate etc. as required. |
| 144 | Telephone Socket outlet. |
| 145 | TV Antenna socket outlet. |
| 146 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm. |
| 147 | Supplying and drawing following pair 0.5 mm dia FR PVC insulated copper conductor, Unarmored Telephone cable in the existing surface/recessed steel/ PVC conduit as required. 2 Pair |
| 148 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 149 | Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non Plenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required. |
| 150 | Supplying & Fixing Modular Type Computer jack RJ 45 ISI mark 1 Module on existing Mounting plate and box Complete with all accessories as required. |
| 151 | INTERNAL LIGHTING FIXTURES & FANS |
| 152 | SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required. |
| 153 | 12W LED Round Down Light |
| 154 | 15 / 16 W LED Round Down Light |
| 155 | 18 /20 W LED Round Down Light |
| 156 | Bulk Head fitting with 9/10Watt LED. |
| 157 | Supply of LED Mirror Light with power 8/10W rated voltage 230V 50 Hz aluminium/ PC body with rauuning life minimum 30000 Hours |
| 158 | S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required. 20/22 W LED Tube Light |
| 159 | SITC LED Batten light (System lumen efficacy ≥105 <120 lm/Watt) 40 watt |
| 160 | SITC LED Panel light 2x2 ft. (System lumen efficacy ≥105 <120 lm/Watt) |
| 161 | 36 watt |
| 162 | 40 watt |
| 163 | Supply & Installation, testing and commissioning of 9-15W LED Bracket Light fitting suitable for 9-15 Watt LED Light with all accessories as required. (Havells Cat no LHFOECE1TZ1O01/ Philips model no 31425/wipro make/ similar to BAJAJ make) |
| 164 | Supply insttalation , testing and commisioning of following size ceiling fan 3 balde confirming to IS : 374:2019 incuding wiring thedown roads of standed lenth ( upto 30 cm ) with 1.5 sqmm PR PVC, insulated copper wire suitable for 230V 50Hz single phase supply etc. compleyte as required. 1200mm (48 Degree) BLDC 5 star rating 32W ceiling fan |
| 165 | Supply and fixing of step type electronic fan regulator on existing modular plate switch box including connection but excluding modular plate etc as required. |
| 166 | Installation, testing and commissioning of ceiling fans/bracket fan of all sizes including wiring the down rod .of standard length (up to 30 cm ) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required. |
| 167 | SITC of 300 mm (12\\") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required |
| 168 | SITC 450 mm (18\\") Metal Body Wall Fan with Speed Regulator Suitable for Single Phase 220V, 50Hz AC Supply complete as required |
| 169 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing |
| 170 | FLOOR PANEL 1 |
| 171 | SITC of cubicle Panel suitable for 415V, 3 phase, 4 wire 50 HZ Ac supply system, fabricated in conmpartmentalized (preferbly) design from CRCA sheet of 2mm thick for frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable Amp capacity extensible type TPN aluminium alloy bus bars of high conductivity, DMC/SMC bus bar supports, , bottom base channel of MS section not less than 50mm x 50mm x 5mm thick, entire pannel shall have a common copper earth bar 25mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of AI. bus bars and control wiring with 2.5 sq.mm. FRLS PVC insulated copper conducter S/C cable, cable alleys, cable gland plates in two half. i/c providing following switch gears :- |
| 172 | INCOMER : 125 AMP 25KA FP MCCB |
| 173 | BUS BAR : 160 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. |
| 174 | digital voltmeter with selecter switch 1 no. digital Am meter with slecter switch required C/T, LED indicating lamp (RYB)- 1no. |
| 175 | OUT GOINGS : |
| 176 | 10 Nos 63 AMP 4P MCB Including 1 set of Indication Lamp |
| 177 | 4 Nos 40 AMP DP MCB Including 1 set of Indication Lamp |
| 178 | complete panel as above and complete |
| 179 | FLOOR PANEL 2 |
| 180 | SITC of cubicle Panel suitable for 415V, 3 phase, 4 wire 50 HZ Ac supply system, fabricated in conmpartmentalized (preferbly) design from CRCA sheet of 2mm thick for frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable Amp capacity extensible type TPN aluminium alloy bus bars of high conductivity, DMC/SMC bus bar supports, , bottom base channel of MS section not less than 50mm x 50mm x 5mm thick, entire pannel shall have a common copper earth bar 25mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of AI. bus bars and control wiring with 2.5 sq.mm. FRLS PVC insulated copper conducter S/C cable, cable alleys, cable gland plates in two half. i/c providing following switch gears :- |
| 181 | INCOMER : 125 AMP 25KA FP MCCB |
| 182 | BUS BAR : 160 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. |
| 183 | digital voltmeter with selecter switch 1 no. digital Am meter with slecter switch required C/T, LED indicating lamp (RYB)- 1no. |
| 184 | OUT GOINGS : |
| 185 | 10 Nos 63 AMP 4P MCB Including 1 set of Indication Lamp |
| 186 | 4 Nos 40 AMP DP MCB Including 1 set of Indication Lamp |
| 187 | complete panel as above and complete |
| 188 | BASEMENT PANEL |
| 189 | Design, manufacture, supply, installation, testing and commissioning of Floor Mounting Panel cubicle type panel fabricated out of CRCA sheet steel , floor mounted totally enclosed switchbaord suitable for use of 415 volts , 3 phase, 50 HZ complete with aluminium bus bar and all accessories including supply and fixing of following incoming and outgoing switchgears, Panel Should Have Double Earthing Provision which connected to the nearest earth grid. |
| 190 | INCOMER : 125 AMP FP MCCB |
| 191 | BUS BAR : 160 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 0.8 sq mm /amp. |
| 192 | The Maximum allowable temperature for the Bus bar to be restricted to 90 deg C. The temperature rise should be restricted to 45 deg C above ambient temperature. |
| 193 | OUT GOINGS : |
| 194 | 3 No 63 AMP 4P MCB Including Indication Lights |
| 195 | 2 No 40 AMP DP MCB Including Indication Lights |
| 196 | complete panel as above and complete |
| 197 | UPS PANEL 1 & 2 |
| 198 | Design, manufacture, supply, installation, testing and commissioning of cubicle type panel fabricated out of CRCA sheet steel , floor mounted totally enclosed switchbaord suitable for use of 415 volts , 3 phase, 50 HZ complete with aluminium bus bar and all accessories including supply and fixing of following incoming and outgoing switchgears, Panel Should Have Double Earthing Provision which connected to the nearest earth grid. |
| 199 | INCOMER : 1 Nos 100 AMP 25KA FP MCCB |
| 200 | BUS BAR : 125 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. |
| 201 | OUT GOINGS : |
| 202 | 3 Nos 63 AMP FP MCB Including 1 set of Indication Lamp |
| 203 | 3 Nos 40 AMP DP MCB Including 1 set of Indication Lamp |
| 204 | complete panel as above and complete |
| 205 | EXTERNAL LIGHT FEEDER PILLAR |
| 206 | Design, Manufacture, Supply, Installation, Testing and Commissioning of Panel Fabricated out of 16 SWG CRCA sheet steel, IP 54, wall / floor mounting type with rain canopy The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes 415 /240 V electrolitic Aluminium Bus Bar, removable gland plates, cable glands, including connection with outgoing feeders complete in all respect, Panel Should Have Double Earthing Provision Which Connected to the Nearest Earth Grid. |
| 207 | INCOMER: |
| 208 | 1 no. 125A, 25KA 4P MCCB with microprocessor based releases, ON indication, 1 no. multifunction meter (showing all power parameters), with Selector Switch, Matching Cast Resin CT's. + 3 Nos 63A DP MCB For each Phase.with 3 Nos Astronomical Weekly programmable time switch (SST- 1min) ON Phase for automaitc switching of landscape light fixtures at sun set and sun rise or twilight (auto on/ auto off and auto mode) with manual override faiclity with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site. |
| 209 | BUS BAR |
| 210 | TPN Aluminium bus bar with heat Shrink Sleeve rated for 125A. |
| 211 | OUTGOING |
| 212 | 18 nos 20A SPN MCB |
| 213 | 2 nos 63A 4P MCB |
| 214 | 2 nos 40A 4P MCB |
| 215 | Other items such as |
| 216 | 1 Set of control wiring |
| 217 | 1 Set of designation plates |
| 218 | complete panel as above and complete |
| 219 | CABLES & ACCESSORIES |
| 220 | SUPPLY OF L.T. CABLE: |
| 221 | Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I). |
| 222 | 3.5 core, 95 sq.mm. |
| 223 | 3.5 core, 70 sq.mm. |
| 224 | 3.5 core, 50 sq.mm. |
| 225 | 3.5 core, 35 sq.mm. |
| 226 | 3.5 core, 25 sq.mm. |
| 227 | LT CABLE LAYING |
| 228 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 229 | LT CABLE JOINTING & END TERMINATION |
| 230 | Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. |
| 231 | 3½ X 25 sq. mm (28mm) |
| 232 | 3½ X 35 sq. mm (32mm) |
| 233 | 3½ X 50 sq. mm (35mm) |
| 234 | 3½ X 70 sq. mm (38mm) |
| 235 | 3½ X 95 sq. mm (45mm) |
| 236 | EARTHING & LIGHTNING CONDUTOR |
| 237 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required. |
| 238 | Earthing with Copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required. |
| 239 | Providing and fixing 25 mm X 5 mm GI strip in 40mm dia GI Pipe from earth electrode including connection with GI nut bolt, spring, washer, excavation and refilling etc as required |
| 240 | Providing and fixing 25 mm X 5 mm Copper strip in 40mm dia GI Pipe from earth electrode including connection with brass nut bolt, spring, washer, excavation and refilling etc as required |
| 241 | Providing and fixing 25 mm X 5 mm Copper strip on surface or in recess for connections etc. as required |
| 242 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required |
| 243 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 244 | Providing and fixing of lighting conductor finial made of 25 mm dia 300 mm long, GI tube having single prong at top with 85 mm dia 6mm thick G.I Base plate including hole etc. as required |
| 245 | Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. ( for Horizental Run) |
| 246 | Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. ( for Vertical Run) |
| 247 | Providing and fixing testing Jointing made of 20mmx 3mm thick G.I Strip 125 mm Long. With 4 nos of G.I bolts. Nuts chuck nuts and spring washers etc. as required |
| 248 | Providing and Laying G.I tape 32mm x 6mm from earth electrode directoly in ground as required. |
| 249 | CABLE TRAYS & RACEWAYS |
| 250 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Cable Tray Bends as per Requirement) |
| 251 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 252 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 253 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 254 | EXTERNAL LIGHTING |
| 255 | S.I.T.C of Following rating LED Post Top lamp made in die cast aluminium housing with decorative clear / opel acrylic diffuser on existing pipe including connection with 1.5sq.mm coppwr conductor etc all complete as required. 20/25W LED Post top lamp clear |
| 256 | S.I.T.C of Following rating LED Street Lighting luminare with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole / pipe for supply voltage 100-270 AC 50Hz Luminare shall be confirm to IS :10322 part 5/ section-3 and shall be complete with all nessessary accessories as required.(Approved Make:- Havells / Philips / Crompton / Wipro). 70/72W LED Street Light |
| 257 | Supplying & installation of 7 mtr. Height Octagonal Hot Dip galvanized pole (BOP. 7030) with top dia 70 mm bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12 mm (LxBxT) including suitable size of foundation bolt all complete as required (without Arm). |
| 258 | 1M Single Arm Suitable for 70MM Top |
| 259 | Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I). 2 core, 6 sq.mm. |
| 260 | Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 2 X 6 sq. mm (19mm) |
| 261 | Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required. 3x2.5 sq mm |
| 262 | Supply of 12mtr High Mast Light in one section construction S355 grade as per BS - EN 10 025 top dia 100 mm, boittom dia 360mm, plate thickness 3mm 12 side polygon galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI Single spike lighting protection, maximum wind speed 47m/s as per IS : 875 (part III) with 6 nos foundation bolt of PCD 445mm TS 600/24mm dia /850mm long. luminarie carriage : material for 40 NB ERW Class B - MS Pipe, dia of carriage ring 450mm (ID) with 8 arm, welded, 2 sections having carring capacity upto 8 luminaries. Trailing cable : 5core 2.5 sqmm. PVC flexible copper conductor winch/power tool : double drum, SWL 750 kg with 0.75HP 6 Pole single speed integral motor rope : Grade AISI 304, 7/19 Construction, dia 5mm, BLC 1450 x 2 having 2 no of continuos rope. aviation obstruction light: twin dome aviation obstruction lights LED type as required. (but excuding feeder pillar) |
| 263 | Installation, Testing, Commissioning of High Mast and Light fixture with help of suitable tools and plants, wiring of luminaries with all wiring material like PVC insulated PVC Sheathed flexible cable of suitable copper conductor lugs, MCB and all labour & construction of shallow foundation with M25 Grade concrete for the high mast considering safe soil bearing capacity of 10T/mtrs sq for 12 mtr High mast |
| 264 | MANHOLE & HUME PIPE |
| 265 | Providing and laying non pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixtures of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete |
| 266 | 150 mm dia |
| 267 | 250 mm dia |
| 268 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 269 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 200 mm dia (OD-200 mm & ID-175 mm nominal) |
| 270 | Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable in existing conduit/ on surface, Category 6 Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C. Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg 1 Run of cable |
| 271 | Supplying, Installation, Testing and commissioning of CAT6 Copper Information Outlet (IO) with face plate of color as per site requirement, should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to mainitain compatibility and interopertability. |
| 272 | Supply, Installation, Testing & Commissioning of 24 port Cat6 Patch Panel loaded. Must be of 1U height with clear label holders and white label with the panel. 24 Ports Cat-6 Patch Panel should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D |
| 273 | Supplying, Installation, Testing and commissioning of following CAT6 Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D Copper Patch Cords of length 1m (3ft) |
| 274 | Supplying, Installation, Testing and commissioning of following CAT6 Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D Copper Patch Cords of length 3m (10ft) |
| 275 | Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side. |
| 276 | Supplying Installation Testing and Commissioning of 5/6MP IP IR Dome Camera having following spcifications and features Type of Camera: Dome Camera Image Sensor: 1/2.8\\" or better progressive Scan CMOS get color image even at night condition Signal System: PAL/NTSC Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0 lux with IR or better Imaging: 1/3s to 1/30000s Shutter Support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. On Screen Display: Camera should display Camera title, Date & Time in live & recorded video both. Signal to Noise Ratio: > 50 dB 5/6MP ((3200 × 1800)@20 fps or better) IP IR 2.7mm ~13.5mm Motorized lens, Vari Focal Dome Camera,Angle of View: H: 104°–32°, V: 54°–18°, D: 125°–36° or better |
| 277 | Supplying Installation Testing and Commissioning of 5/6 MP IP Type of Camera: Bullet Camera Image Sensor: 1/2.8\\" or better progressive Scan CMOS get color image even at night condition Signal System: PAL/NTSC Minimum Illumination: 0.006Lux@ F1.4, AGC ON, 0 lux with IR or better Imaging: 1/3s to 1/30000s, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. On Screen Display: Camera should display Camera title, Date & Time in live & recorded video both. Signal to Noise Ratio: > 50 dB IR Bullet Camera having following spcifications and features 5/6MP ((3200 × 1800)@20 fps or better) IP IR 2.7mm ~13.5mm Motorized lens, Vari Focal outdoor Bullet Camera,Angle of View: H: 104°–32°, V: 54°–18°, D: 125°–36° or better |
| 278 | 5MP IP IR motorized PTZ @25/30fps or better camera, Triple streaming , configurable on resolution:- Main stream: 5MP@25/30 fps Sub treams:1080p@25/30 fps, varifocal lens 3.95mm (±5mm) ~ 177.75mm (±5mm) or better with Automatic & manual Focus Adjustment provisions, 45x Optical zoom and 16x Digital zoom with angle of view H: 65.7°–1.9°V: 39.4°–1.1°D: 73.1°–2.1, PAN Travel: Pan: 0° ~ 360° endless,Manual Pan: 260° /s, Preset : 300° /s, Tilt Travel: Tilt: -20° ~ 90°, auto flip 180°, Manual Tilt: 120° /s, Preset : 200° /s |
| 279 | Supply, installation, testing and commissioning of 64 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16/25/36/64, 2nd screen: 1/4/8/9/16 |
| 280 | Supplying, Installation, Testing and Commissioning following capacity Serveillance grade Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL certifications. 10TB (Terabytes) |
| 281 | Supply, Installation, Testing and Commissioning of Full HD 55\\" LED Professional Display Panel. |
| 282 | Supply, Installation, Testing & Commissioning of L2+ managed industrial PoE switch with 4*10/100/1000M RJ45 ports and 2*100/1000M SFP slot ports, Port 1-4 can support IEEE802.3af/at PoE. Switching capaticy of 128Gbps, forwarding Rate 8.93 Mpps, having 4 x 10/100/1000BASE-T PoE-plus(RJ45) with maximum PoE output power is 60W (at-120W) , with 2*100/1000Base-X uplink SFP slot ports., 8K MAC address. Should have Static Routing , system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), and IPv6 features from day 1. |
| 283 | 8 port PoE Layer 2 Network Switch with PoE Support of 130W or higher with each copper port supporting 802.3at PoE+. |
| 284 | Supply, Installation, Testing & Commissioning of L2+ managed industrial PoE switch with 24*10/100/1000M RJ45 ports and 4*1/10G SFP+ fiber slot ports, Port 1-24 can support IEEE 802.3af/at PoE standard, switching capaticy of 598 Gbps, forwarding performance 95.23 Mpps, maximum PoE output power is 400W(at-600W), with 32K MAC address. Should have Static Routing , system logging, Telnet, SSH2.0, SNMP V1/V2C/V3, Network Time Protocol (NTP), FTP, TFTP, Xmodem |
| 285 | Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5\\" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest. |
| 286 | PLUMBING WORK |
| 287 | SANITARY INSTALLATIONS |
| 288 | Supplying , fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I 'p' trap 15 liters C.I.pull and let go flushing cistren of names or other I.S.S. equivalent make , complete with all fitting , C.I.or C.C. brackets 32mm alkathene/P.V.C telescopic flush , pipe about 2 M long with one brass coupling and clamps GI ,chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less thane 50grms. 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coats of red oxide primer etc. all complete as per specification and direction of E/I. |
| 289 | (A) 580 mm. long |
| 290 | (c) With 10 lit. low level PVC Cistem |
| 291 | Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all completeas per specification and direction of E/I. |
| 292 | (ii) E.W.C. with 'S' trap |
| 293 | (b) 10 lit. low level PVC Cistem |
| 294 | (b)Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. |
| 295 | (i) 600mm x 450mm size |
| 296 | (c)(iii) C.P. brass liquid soap container |
| 297 | Provinding and fixing wash basin wih C.I brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereever required : White Vitreous China Wash basin size 550x400 mm with a 15mm CP Brass single hole basin mixer |
| 298 | Providing and fixing white vitreous china laboratory sink with CI brackets , C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets , cutting and making good the wall wherever required : Size 600x450x200 mm |
| 299 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge. |
| 300 | Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete Flexible Pipe 32/40 mm Dia |
| 301 | Providing and fixing toilet paper holder : C.P. brass |
| 302 | Providing and fixing PTMT Bottle Trap for Wash basin. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms. |
| 303 | Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms |
| 304 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore |
| 305 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 306 | Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms |
| 307 | Providing and fixing CP brass single lever low flow Sink mixer with 15 mm CP brass single lever pillar cock with pop up and waste complete including cutting and making good the walls where required |
| 308 | Providing,Fixing satin finish stainless steel AISI 316 grade wall mounted coat hook on door complete. The rate include cost of all material & labour involved in the item complete and all as per direction of engineer incharge. |
| 309 | DRAINAGE INSTALLATIONS |
| 310 | Providing, fixing, testing and commissioning of UPVC SWR pipe type 'B' conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps etc. conforming to IS:14735-1999 and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint as required/applicable. 110 mm (OD) |
| 311 | Providing, fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of self cleansing design having 50 mm water seal with or without horn conforming to IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20 mm nominal size) including cost of cutting and making good the walls & floors wherever required. 110 mm inlet x110 mm outlet. |
| 312 | Providing, fixing, testing and commissioning of UPVC inlet fittings (hopper) receive waste from fixture waste with maximum 3 inlets 40, 50 & 63 mm OD size, fabricated from 110 OD UPVC SWR pipe, UPVC sockets, fixed to UPVC traps including solvent weld joint/rubber ring joint, complete with all civil work set in cement concreate 1:2:4 as required including cost of cutting and making good the walls & floors wherever required. |
| 313 | Providing, fixing, testing and commissioning of UPVC waste Pipe conforming to IS : 4985-2000 class III including all moulding fittings conforming to IS : 7834 (Part-1 - Part -7) 1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded joint as per manufacturer recommendation including cutting and making good the walls, floors, R.C.C. work etc. (For fixtures waste). |
| 314 | 40 mm (OD) |
| 315 | 50 mm (OD) |
| 316 | Providing and fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect. 110 mm OD x 63 mm OD |
| 317 | Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. For 100mm dia. Pipe |
| 318 | Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole |
| 319 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 320 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 321 | Coupler 110 mm |
| 322 | Bend 87.5° 110 mm bend |
| 323 | Shoe (Plain) 110 mm Shoe |
| 324 | Providing, fixing, testing and commissioning of UPVC rain water pipes (IS : 4985-1983 class-III ) including injection moulded fittings (heavy duty) (plain or door) e.g. bends, junction, cowls, tees, offsets, access pieces etc. Clamps/Supports jointing with rubber ring/solvent cement joints including cutting chase or holes in walls and floors and making good as required at Site [For Balcony Drain + Terrace Rain Water Downtake Pipe]. 160 OD |
| 325 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 326 | WATER SUPPLY INSTALLATIONS |
| 327 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 328 | Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (Exposed on wall Terrace) |
| 329 | 32 mm dia, nominal bore |
| 330 | 40 mm dia, nominal bore |
| 331 | Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. 25 to 40 mm nominal bore |
| 332 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) |
| 333 | 25 mm dia, nominal bore |
| 334 | 32 mm dia, nominal bore |
| 335 | 40 mm dia, nominal bore |
| 336 | Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality |
| 337 | 32 mm dia, nominal bore |
| 338 | 40 mm dia, nominal bore |
| 339 | Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete. |
| 340 | 20mm nominal bore |
| 341 | 25mm nominal bore |
| 342 | 32mm nominal bore |
| 343 | 40mm nominal bore |
| 344 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 15mm nominal bore |
| 345 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm dia nominal bore |
| 346 | Provide and fixing PTMT ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P/H.P.H.D. plastic ball 50 mm dia NB, 242mm long. Weighing not less than 1240 gms. |
| 347 | Providing and fixing chlorinated poly vinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fitting, including fixing the pipewith clampsat 1 m spacing. This includesjointing of pipes &fittingwith one step CPVC solvent cement and cost ofcutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge.(Concealed work including cutting chases and making good the walls etc.) |
| 348 | 15mm nominal outer dia. Pipes. |
| 349 | 20mm nominal outer dia. Pipes. |
| 350 | 25mm nominal outer dia. Pipes. |
| 351 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 50mm diameter |
| 352 | Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified 100 mm nominal bore 50 mm dia. |
| 353 | Providing, laying, Jointing, Testing and commissioning of uPVC pressure pipes of 10Kg/Sqcm pressure rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per standard design. 32 OD mm. |
| 354 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 355 | Constructing masonry Chamber 60x45x50 cm,inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. With F.P.S. bricks |
| 356 | SEWERAGE & DRAINAGE INSTALLATIONS UPTO MAIN ROAD FIRST MANHOLE |
| 357 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete: |
| 358 | 150 mm diameter |
| 359 | 200 mm diameter |
| 360 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : |
| 361 | 150 mm diameter S.W. pipe / RCC pipe |
| 362 | 200 mm diameter S.W. pipe / RCC pipe |
| 363 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 364 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe |
| 365 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 366 | Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5 |
| 367 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 368 | Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 369 | Extra for depth for manholes: Size 90 x 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 370 | Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 371 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 372 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : |
| 373 | For pipes 100 to 250 mm diameter |
| 374 | For pipes 350 to 450 mm diameter |
| 375 | Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 376 | FIRE FIGHTING WORK |
| 377 | (WET RISER SYSTEM - PUMPING EQUIPMENTS) |
| 378 | Supply, Installation, Testing and Commissioning of Electric Driven Main Fire Pump suitable for auto operation & consisting of following: complete in all respect as required.The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% of the rated head. The shut off head shall not exceed 120% of the rated head. (Sprinkler & Hydrant Pump) |
| 379 | a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520. |
| 380 | b) Suitable HP squirrel cage induction motor, TEFC synchronous speed 2900 RPM (with permissible slip), suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, confirming to IS-325. |
| 381 | c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications. |
| 382 | Supply, Installation, Testing and Commissioning of Diesel Engine Driven Main Fire Pump suitable for auto operation and consisting of following: complete in all respect as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head. The shut off head shall not exceed 120% of the rated head. |
| 383 | a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520. |
| 384 | b) Suitable HP 1500 RPM, 4 stroke, cold starting type Diesel Engine with Heat Exchanger confirming to relevant BIS & IS Standards, complete with all required accessories / system, fuel oil filter, lubricant oil pump with filter, 2 Nos. starting batteries of 180 AH capacity each with suitable angle iron stand, engine starting panel having all the controls meters, gauges, tachometer, hour meters, starting switch with keys for manual starting, auto starting mechanism, Including inbuilt electrical panel which will be activate by pressure switch, Including cables etc., 24 Volts electric starting equipment, Diesel Tank for 8 hrs continuous running of diesel engine, having minimum capacity of 200 Ltrs. (tank made out of 3mm thick M.S. Sheet with filling Cap, drain Cock, diesel indicator duly mounted on M.S. angle) exhaust pipe extended upto 1 mtr. outside pump house, duly insulated with 50 mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, exhaust residential silencer, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. |
| 385 | c) M.S. fabricated Common base frame, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation (minimum 6\\" above from ground floor) duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications. |
| 386 | Supplying, Installation, Testing and Commissioning of Electric Driven Pressurization Pump (Jockey Pump) suitable for auto operation and consisting of following: complete in all respects as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head. |
| 387 | a) Horizontal type, centrifugal end suction type pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal, gland packing and flow of 180 Ipm at 88Mtr. head confirming to IS:1520. |
| 388 | b) Suitable HP (Minimum 4.0-5.0 HP) squirrel cage induction motor TEFC type 2900 RPM suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP-55 class of protection for enclosure, horizontal foot mounted type with Class - 'F' insulation, confirming to IS:325. |
| 389 | c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications. |
| 390 | Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 6 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes 1.2 Meter high and 250 mm dia |
| 391 | Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 8 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes 2 Meter high and 450 mm dia suitable to operate Jockey Pump, Main Fire Pump , Sprinkler pump & Diesel Engine Driven Fire Pump |
| 392 | HYDRANTS SYSTEM |
| 393 | Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS : 5290 (Type A), with 80 mm dia flanged inlet, with ABS cap and chain complete with all accessories etc. as required. |
| 394 | Supply, Installation, Testing and Commissioning of 63 mm dia. 15 Mtr. Long RRL hose pipe with 63 mm dia. male and female stainless steel couplings duly binded with GI wire rivets etc. ISI marked, IS 636 (type-A) as required. |
| 395 | Supplying and fixing 63 mm dia. Stainless Steel branch pipe with 20mm dia nozzle conforming to IS:903. suitable for instantaneous connections to hose pipe coupling etc. as required. |
| 396 | Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction, spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required. |
| 397 | 30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585 |
| 398 | 20 mm dia. ball valve & nozzle. |
| 399 | Drum and brackets for fixing the equipments on wall. |
| 400 | Connection from riser with 25 mm dia (Gun metal) stop valve & M.S. Pipe. |
| 401 | Supplying, installation, testing and commissioning of weather proof M.S cabinet size 1200 mm x 2100 mm x 600mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following. |
| 402 | Gunmetal single headed Hydrant valve - 1 No. |
| 403 | Fire Hoses 63mm, 15 M long with accessories - 2 Nos. |
| 404 | Short branch - 1 No. |
| 405 | First Aid hose Reel - 1 No. |
| 406 | Fire Extinguisher - 2 Nos. |
| 407 | Fireman's Axe - 1 No. |
| 408 | Pressure Gauge - 1 No. |
| 409 | The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade. |
| 410 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male & female instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : |
| 411 | 2 way - 100 mm dia M.S. Pipe |
| 412 | 4 way - 150 mm dia M.S. Pipe |
| 413 | PIPING, VALVES AND ACCESSORIES |
| 414 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of requiredshade complete as required : |
| 415 | 150 mm dia |
| 416 | 100 mm dia |
| 417 | 80 mm dia |
| 418 | 65 mm dia |
| 419 | 50 mm dia |
| 420 | 40 mm dia |
| 421 | 32 mm dia |
| 422 | 25 mm dia |
| 423 | Supplying, Installation, Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with EPDM rubber lining seat and CF-8 stainless steel disc duly ISI marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required. |
| 424 | 150 mm dia |
| 425 | 80 mm dia |
| 426 | 65 mm dia |
| 427 | Supplying and fixing Orifice Plate made of 6 mm thick, stainless steel with orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 Kg / cm2 complete as per specifications as required. |
| 428 | Providing, Installation, Testing and Commissioning of double flanged cast iron Dual Plat Check Valve (Non-Return Valve), PN 1.6 of following sizes confirming to IS : 5312 complete with EPDM rubber lining seat and stainless steel disc, rubber gasket, Gl bolts, nuts, washers etc. as required. |
| 429 | 150 mm dia |
| 430 | 65 mm dia |
| 431 | Supplying, Installation, Testing and Commissioning of CI body flanged (both ends) type serviceable suction / Y strainer with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. complete as required. 150 mm dia |
| 432 | Providing & fixing double flanged Metallic expansion with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications. |
| 433 | 150 mm dia |
| 434 | 65 mm dia |
| 435 | Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centrigade with required accessories : |
| 436 | Pendent Sprinkler |
| 437 | Sidewall Sprinkler |
| 438 | Providing & fixing of pressure gauge in M.S. pipe line including connection etc. as required. |
| 439 | Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150mm dia |
| 440 | Providing, fixing, testing & commissioning of installation control valve of cast irom body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulic driven mechanical gong bell to sound continous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency release, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice pate, gasket etc of following sizes as required 150mm dia |
| 441 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes coplete as required. |
| 442 | 700mm |
| 443 | 1000mm |
| 444 | Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926. |
| 445 | FIRE EXTINGUISHERS |
| 446 | Powder Fire Extinguisher (Stored Pressure type) Capacity 09 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609, ISI marked ABC powder complete with squeeze grip release valve, discharge pipe locking arrangement, pressure gauge, operation manual and bracket. Operating Temperature: - 10ºC to + 55ºC. Brand LIFEGUARD |
| 447 | Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006 4.5kg capacity cylinder |
| 448 | Providing and fixing in position approved make fire bucket of 24 gauge, galvanized steel, standard 9 liters capacity and of round bottom shape, panted white inside and red outside and black on bottom dome with letters ‘FIRE’ in black and gold with all mounting bracket and screws. |
| 449 | Providing and fixing of fire Bucket Stand including sheet metal (16 gauge) shade for 2 buckets. Platform and associated civil works complete. |
| 450 | ELECTRICAL CABLES |
| 451 | Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium / Copper conductor armoured cables as per specification as required. PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Aluminium conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1) |
| 452 | 3.1/2 core 120sq. mm. |
| 453 | 3.1/2 core 50sq. mm. |
| 454 | 4 core 10 sq. mm. |
| 455 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 456 | Above 35 sq. mm and upto 95 sq. mm |
| 457 | Above 95 sq. mm and upto 185 sq. mm |
| 458 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required Upto 35 sq. mm |
| 459 | Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade. |
| 460 | 3.1/2 core 120sq. mm. |
| 461 | 3.1/2 core 50sq. mm. |
| 462 | 4 core 10sq. mm. |
| 463 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Powder coated shall be of Siemens Grey Colour- RAL 7032) |
| 464 | 100 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 465 | 150 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 466 | Providing and fixing 6 SWG dia. GI wire on surface or in recess for loop earthing along with the existing surface / recessed conduits / submain wiring / cable as required. |
| 467 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc, as required |
| 468 | FURNITURE WORK |
| 469 | Single Bed Supplying, and placing in position of newton single bed premium metal material moder design guest room single bed size is Size: 2005Lx987Wx914H mm. square + rectangle shaped framing makes it warp and scratch resistant, comfortable designed keeping modern Indian lifestyle in mind, material used black metal powder coated ,the headboard and mattress frame encourage room, designed with modern & elegance, choose the option that suits your home.construction structure are made in metal in black powder coating colour, headboard have a unique semi-circle shape top tube of headboard 19.05 x 0.7 mm thick metal frame structure are made in metal 50.8 x 0.9 mm thick below that exclusive design metal pipes 15.88 x 0.8 mm thick. Bed stead main frame structure are made in metal rec tube 50.8 x 25.4 x 0.9 thick and the main mattress panel structure are made in metal square tube 19.05 x 0.8 mm thick, mattress central panel structure are made in metal rec tube 40 x 20 x 0.8 mm thick.bed based on semi-circle shape tube structure are made in metal 50.8 x 0.9 mm thick.all metal parts should be finishing with epoxy polyester black powder coated to the thickness of 50-60 microns(+/-5 micron). The main mattress panel structure is made in 1 mm MS sheet.The Seller / Company should be ISO 9001:2015, ISO-14001:2015, ISO-37001:2016, OHSAS 18001:2007, ISO-45001:2018, ISO-50001:2018, GRIHA, GREENPRO, GREEN GUARD, INDIAN DESIGN MARK, AIOTA, FSC, BIFMA Level- 1 certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL-1 certified and an official product link/screenshot of the product listing's must be provided from www.bifma.orgall complete as per specifications and direction of Engineer-in-Charge. |
| 470 | Office Desk Size: 900Wx600Dx750H mm.Supplying and placing in position of primary work surface 18mm thick table top made of 18mm thick prelaminated particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. modesty panel made of 18mm thick. under structure made of 18mm thick. Construction below table top right side on 1 drawer with lock right & left side table top based on a 18mm thick side panel .1 drawer, in provided with lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with facia of drawers. three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest. The Seller / Company should be ISO 9001:2015, ISO-14001:2015, ISO-37001:2016, OHSAS 18001:2007, ISO-45001:2018, ISO-50001:2018, GRIHA, GREENPRO, GREEN GUARD, INDIAN DESIGN MARK, AIOTA, FSC, BIFMA Level- 1 certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL-1 certified and an official product link/screenshot of the product listing's must be provided from www.bifma.orgall complete as per specifications and direction of Engineer-in-Charge. |
| 471 | Premium Leatherette Chair, Low Back Supplying, and placing in position of Jewel, Premium Leatherette Chair, Low Back. Dimension: (W) 470mm X (D) 400mm X (H) 890mm. Seating Height: 490mm, Seat depth: 400mm, Back Height: 400mm. The chair made of full leatherette in black colour .it will comes in matte finsih in contemporary style .details :arms : with out arms.use of ply: seat & back plywood made of 12 mm hot pressed.seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support seat height is @ 490mm . base : four chrome legs .The Seller / Company should be ISO 9001:2015, ISO-14001:2015, ISO-37001:2016, OHSAS 18001:2007, ISO-45001:2018, ISO-50001:2018, GRIHA, GREENPRO, GREEN GUARD, INDIAN DESIGN MARK, AIOTA, FSC, BIFMA Level- 1 certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL-1 certified and an official product link/screenshot of the product listing's must be provided from www.bifma.orgall complete as per specifications and direction of Engineer-in-Charge. |
| 472 | 2 Door Wardrobe in Frosty White Supplying, and placing in position of Juda, 2 Door Wardrobe Material & Subtype Laminate, Engineered Wood - Particle Board, Frame Material, Engineered Wood, Laminate, Finish Matte, Colour & Colour Family White - Frosty, Dimension (W) 800mm X (D) 550mm X (H) 1950mmThe Seller / Company should be ISO 9001:2015, ISO-14001:2015, ISO-37001:2016, OHSAS 18001:2007, ISO-45001:2018, ISO-50001:2018, GRIHA, GREENPRO, GREEN GUARD, INDIAN DESIGN MARK, AIOTA, FSC, BIFMA Level- 1 certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL-1 certified and an official product link/screenshot of the product listing's must be provided from www.bifma.org all complete as per specifications and direction of Engineer-in-Charge. |
| 473 | King Size Bed in Walnut Finish with LED Light Supplying, and placing in position of Alister, King Size Bed Material & Subtype Solid Wood - Steam Beech Wood, Engineered Wood - Particle Board, Headboard Material Engineered Wood, Frame Material Engineered Wood, Leg Material Solid Wood, Finish Matte, Colour & Colour Family Brown - Walnut, Dimension (W)1945mm X (D)2170mm X (H)980mm, Headboard Height 680mm, Seating Height 320mm, Function LED Light Strip The Seller / Company should be ISO 9001:2015, ISO-14001:2015, ISO-37001:2016, OHSAS 18001:2007, ISO-45001:2018, ISO-50001:2018, GRIHA, GREENPRO, GREEN GUARD, INDIAN DESIGN MARK, AIOTA, FSC, BIFMA Level- 1 certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL-1 certified and an official product link/screenshot of the product listing's must be provided from www.bifma.org all complete as per specifications and direction of Engineer-in-Charge. |
| 474 | 2 Door Wardrobe with External Drawer Supplying, and placing in position of Alister, 2 Door Wardrobe Material & Subtype Engineered Wood - Particle Board, Solid Wood - Steam Beech Wood, Laminate, Frame Material Laminate, Engineered Wood, Finish Matte, Colour & Colour Family Brown - Walnut, Dimension (W)900mm X (D)550mm X (H)1950mm The Seller / Company should be ISO 9001:2015, ISO-14001:2015, ISO-37001:2016, OHSAS 18001:2007, ISO-45001:2018, ISO-50001:2018, GRIHA, GREENPRO, GREEN GUARD, INDIAN DESIGN MARK, AIOTA, FSC, BIFMA Level- 1 certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL-1 certified and an official product link/screenshot of the product listing's must be provided from www.bifma.orgall complete as per specifications and direction of Engineer-in-Charge. |
| 475 | Queen Size Bed in Walnut Finish with LED Light Supplying, and placing in position of Alister,Queen Size Bed Material & Subtype Solid Wood - Steam Beech Wood, Engineered Wood - Particle Board, Headboard Material Engineered Wood, Frame Material Engineered Wood, Leg Material Solid Wood, Finish Matte, Colour & Colour Family Brown - Walnut, Dimension (W)1645mm X (D)2170mm X (H)980mm, Headboard Height 680mm, Seating Height 320mm, Function LED Light Strip The Seller / Company should be ISO 9001:2015, ISO-14001:2015, ISO-37001:2016, OHSAS 18001:2007, ISO-45001:2018, ISO-50001:2018, GRIHA, GREENPRO, GREEN GUARD, INDIAN DESIGN MARK, AIOTA, FSC, BIFMA Level- 1 certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL-1 certified and an official product link/screenshot of the product listing's must be provided from www.bifma.org all complete as per specifications and direction of Engineer-in-Charge. |
| 476 | Add GST 18 % |
| 477 | Add Labour cess 1% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 03, 2026
11:30 IST
Tender Published
Tender notice published.
TodaySep 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysSep 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender