Tender For Construction Of District Panchayat Resourse Centre (Dprc) Building At Kullu, Distt. Kullu, (Himachal Pradesh). (Sub Head:- Civil Work In Ground Floor And First Floor, Water Supply & Sanitary Installations And Construction of Septic Tank Et
Tender Value
1.55 Crore
Estimated cost
Bid Submission
17 Sep 2026
3 days left
EMD
3.10 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kullu → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of District Panchayat Resourse Centre (Dprc) Building At Kullu, Distt. Kullu, (Himachal Pradesh). (Sub Head:- Civil Work In Ground Floor And First Floor, Water Supply & Sanitary Installations And Construction of Septic Tank Etc.)
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in soil in Hilly area by mechinical /Manual means in all heights and depths all kinds of soil such as a pick work , jumper work , blasting work both in soft and hard rock with chiesling / wedging out rock (where blasting is prohibited ) and other intermediate classification of soil including cutting and trimming of side slopes and disposal unserviceable material by mechnical transport to designated dumping site and stacking the serviceable/ useful material as directed by the Engineer -in - Charge, muttams shall be left at suitable place as directed by Engineer- in - Charge and shall be removed only after attaining the formation level and after final checking of Engineer-in- Charge. The work shall be executed in workman like manner and avoid any damage to the private / Govt. property in the vicinity of work site , if any damage occurs to any property during the course of execution shall be the absolute responsibility of the contractor , which shall have to be duly compensated by him in all cases, including carriage of materials with in all leads, lifts and other incidentals. |
| 2 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete as per the direction and to the entire satisfaction of Engineer-in-Charge. |
| 3 | Providing and laying, mechanically mixed and vibrated cement concrete 1:4:8 (one cement : four sand : eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) in foundation and plinth including curing complete excluding the cost of form work but including carriage of material with in all leads, lift, and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 4 | Providing and laying, mechanically mixed and vibrated cement concrete 1:5:10 (one cement : Five sand : Ten graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing complete excluding the cost of form work above plinth level up to floor all level including carriage of material within all leads, lifts and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 5 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm nominal size) over 75 mm (seventy five milimetre) thick bed of dry brick ballast 40 mm (forty mimi metre) nominal size, well rammed and consolidated and grouted with fine sand, including carriage of materials with in all leads, lifts and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge. |
| 7 | Reinforced cement concrete work in walls any thickness including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level excluding the cost of centering, shuttering, finishing and reinforcement in secified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge. |
| 8 | Reinforced cement concrete work in Beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all levels excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge. |
| 9 | Reinforcement cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° (fifteen degree) up to all floor level excluding the cost of centring, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed vibrated and curing complete including carriage of materials with in all leads, lift and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 10 | Providing form work with steel plates 3.15 mm ( three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5 mm (Thirty millimetre x Thirty millimetre x five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in: |
| 11 | Foundation ,footing basis of columns etc. and mass concrete. |
| 12 | Flat surfaces, such as soffits of the suspended floors roofs , landings, balconies and access platform and the like floors etc. up to any thickness. |
| 13 | Beams cantilever girders and lintels, side and soffits of beams, beams haunchings, cantilevers, bressumers and lintels any depth in all heights from floor. |
| 14 | Columns, pillars, posts and struts square, rectangular or polygonal in plan as required. |
| 15 | Stair case with sloping or stepped soffits excluding landing as per direction of the Engineer-in Charge |
| 16 | Small lintels note xceeding1.5 m clearspan, mouldingas incornices, windowsills, string courses, bandsds, copings, bedplates, anchor blocks and the like |
| 17 | Form work in edges of slab and breaks in floor and walls under 20 cm wide as required. |
| 18 | Providing tor steel reinforcement TMT bars of grade Fe-500 D or more ISI make high yield strength for reinforced cement concrete work including straightening, cutting ,bending, binding and placing in position and cost of binding wire complete up to floor all levels including carriage of material with in all leads, lifts and other incidentals complete as per direction and to the entire satisfaction of Engineer-in-Charge |
| 19 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in cement mortar 1:6 (one cement : six sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 20 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in cement mortar 1:4 (one cement : four sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 21 | Random rubble masonry with hard stone of approved quailty in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including curing complete and carriage of materials with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 22 | Boulder filling under floors over preparing surface complete. including carriage of materials with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 23 | Providing and fixing 18 mm thick granite stone, gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all level. Area of slab over 0.50 sqm. including carriage of materials with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 24 | Providing edge moulding to 18 mm thick granite stone, marble or kota stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. |
| 25 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete including carriage of materials with in all leads, lifts and other incidentals. |
| 26 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) complete including carriage of materials with in all leads, lifts and other incidentals. |
| 27 | Providing second class deodar wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position, as required including carriage of materials with in all leads, lifts and other incidentals. |
| 28 | Providing and fixing second class deodar wood 40 mm (forty millimeters ) thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows, including black enameled iron butt hinges with necessary screws including carriage of material with in all leads , lifts and other incidentals . |
| 29 | Providing and fixing second class deodar wood 40 mm wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws including carriage of material with in all leads , lifts and other incidentals . |
| 30 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick complete including carriage of materials with in all leads, lifts and other incidentals. |
| 31 | 5 mm thick glass pans (weight not less then 12.5 kg/sqm) |
| 32 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). including carriage of materials with in all leads, lifts and other incidentals. |
| 33 | Providing and fixing ISI marked flush door shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws etc. conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including carriage of materials with in all leads, lifts and other incidentals. |
| 34 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws etc. |
| 35 | Providing extra for lipping with 2nd class teak wood battens 25 mm (twenty-five milimetre) minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)complete including carriage of materials with in all leads, lifts and other incidentals. |
| 36 | Providing and fixing 50x20 mm wooden moulded beading to door and window frames in 2nd class teak wood with iron screws, plugs and priming coat on unexposed surface etc. complete including carriage of materials with in all leads, lifts and other incidentals. |
| 37 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including carriage of materials with in all leads, lifts and other incidentals. |
| 38 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete including carriage of material with in all leads, lifts and other incidentals. |
| 39 | Providing and fixing bright finished stainless steel sliding door bolts, ISI marked with nuts, bolts & screws complete with in all leads, lifts and other incidentals. |
| 40 | 300 x 16 mm (three hundred X sixteen mili metres) |
| 41 | 250 x 16 mm (two hundred fifty X sixteen mili metres) |
| 42 | Providing and fixing bright finished stainless steel tower bolts, ISI marked with screws complete with in all leads, lifts and other incidentals. |
| 43 | 200 x 10 mm (two hundred X ten mili metres) |
| 44 | 100 x 10 mm (one hundred X ten mili metres) |
| 45 | Providing and fixing 50 cm long Stainless Steel kicking plate of size 100x3.15 mm, to required colour or shade, with necessary screws etc. complete with in all leads, lifts and other incidentals. |
| 46 | Providing and fixing stainless steel handles, ISI marked with screws complete with in all leads, lifts and other incidentals. |
| 47 | 150 mm (one hundred fifty milimeter) |
| 48 | 100 mm (one hundred milimeter) |
| 49 | Providing and fixing twin rubber stopper Stainless Steel hanging floor door stopper, ISI marked, with necessary screws etc. complete. with in all leads, lifts and other incidentals. |
| 50 | Providing and fixing 200 mm weighing not less than 240gms bright finished Stainless Steel casement stays (straight peg type) , with necessary screws etc.complete with in all leads, lifts and other incidentals. |
| 51 | Providing and fixing aluminium work for doors, windows ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portion, Powder coated aluminium (minimum thickness of powder coating 50 micron) including carriage of material with in all leads, lifts and other incidentals. |
| 52 | Providing and fixing glazing with float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm) in aluminium door, window,ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item) including carriage of material with in all leads, lifts and other incidentals. |
| 53 | Providing and fixing double action hydraulic floor spring with stainless steel cover plate minimum 1.25 mm thickness of approved brand and manufacture conforming to IS :6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 54 | Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer as required including carriage of materials with in all leads, lifts and other incidentals as per direction by the Engineer-in-Charge. |
| 55 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of materials with in all leads, lifts and other incidentals as per direction by the Engineer-in-Charge. |
| 56 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 57 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 58 | Providing and fixing 1st quality ceramic glazed wall tiles of size 300mm x 600mm conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 59 | Providing and laying vitrified floor tiles 600 mm x 600 mm x 10 mm with water absorption less than 0.08 % and conforming to IS: 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours and shades, laid on 20 mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 60 | Providing and laying Vitrified tiles 600 mm x 600 mm x 10 mm with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (one cement : three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 61 | 25 mm thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 oarse sand ) including carriage of material with in all leads, lifts and other incidentals. |
| 62 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including carriage of material with in all leads, lifts and other incidentals. |
| 63 | Providing and fixing 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws complete with all accesoriees as per the directon of engineer in charge including carriage of material with in all leads, lifts and other incidentals. |
| 64 | Providing and fixing M.S BP sheet 1.66 mm to 2 mm thick in eaves board / facia / soffit / ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of engineer in charge ( base members of steel work shall be measured and paid separtely including carriage of material with in all leads lifts in all floors as required as per the direction of Engineer-in-charge. |
| 65 | Providing and fixing 110 mm dia (one hundred ten mili metre) with minimum pressure of 4.5 kg/sqm on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage of materials with in all leads, lifts and other incidentals. |
| 66 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories of working pressure 4 Kgf/sq cm for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of material in all leads & lifts and other incidentals. |
| 67 | 110 mm bend (one hundred ten mili metres) |
| 68 | 110 mm shoe (one hundred ten mili metres) |
| 69 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty X fifty X fifty mili metres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete. including carriage of material with in all leads, lifts and other incidentals. |
| 70 | 110 mm diameter (one hundred ten mili metres) |
| 71 | 6 mm (six millimeter) thick cement plaster to ceiling in cement mortar 1:3 (one cement : three sand) including carriage of material with in all leads, lifts and other incidentals. |
| 72 | 15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete / stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and / or rounded angles not exceeding 80 mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement : six sand ) including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 73 | Providing and applying white cement based putty of average thickness 1 mm (one milimeter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 74 | Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 75 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 76 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 77 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10sqm) including carriage of material with In all leads, lifts in all floors and other incidentals completes as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 78 | Providing and laying 40 mm thick cement concrete flooring 1:2:4 (one cement : two sand : four crushed stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of a neat cement including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 79 | Supplying and fixing C.I. cover without frame for manholes complete in all respect including carriage of material with in all leads, lifts and other incidentals. |
| 80 | 455 mm x 610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg. |
| 81 | Providing M.S. foot rests With 20 mm x 20 mm square bar including fixing in manholes with 20 cm x 20 cm x 10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design complete in all respect including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 82 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 83 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) cera/hindware/parryware make with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 84 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) cera/hindware/parryware make with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china orissa pattern W.C. pan of size 580x440 mm with integral type foot rests as required including carriage of material with in all leads, lifts and other incidentals. |
| 85 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin cera/hindware/parryware make of 430 x 260 x 350 mm (four hundred thirty X two hundred sixty X three hundred fifty milimeters) and 340 x 410 x 265 mm (three hundred forty X four hundred ten X two hundred sixty five milimeters) sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 lt. white P.V.C automatic flushing cistern as required including carriage of material with in all leads, lifts and other incidentals. |
| 86 | Providing and fixing White Vitreous China Wash basin cera/hindware/parryware make size 550 x 400 mm (five hundred fifty X four hundred mili meters) with a pair of 15 mm C.P. brass pillar taps wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of material with in all leads, lifts and other incidentals. |
| 87 | Providing and fixing white vitreous china pedestal for wash basin cera/hindware/parryware make completely recessed at the back for the reception of pipes and fittings as required including carriage of material with in all leads, lifts and other incidentals . |
| 88 | Providing and fixing Stainless Steel ISI 304 (18/8) kitchen sink 510 mm x 1040 mm bowl depth 225 mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 89 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. The sample of heavy duty jet should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 90 | Providing and fixing 32 mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 91 | Providing and fixing 100 mm stainless steel grating heavy duty for gully trap. complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 92 | Providing and fixing 600 x 450 mm beveled edge mirror of heavy dutysuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 93 | Providing and fixing 600 x 120 x 5 mm heavy duty of approved quality glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 94 | Providing and fixing CP brass heavy duty toilet paper holder complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 95 | Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete in all respect (cost of water meter and stop cock to be paid separately). |
| 96 | Providing and fixing uplasticised PVC connection pipe 45 cm long with brass unions complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 97 | 15 mm nominal bore |
| 98 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of jaquar/jal/ess ess make of approved quality conforming to IS:8931 : The sample quality & series should be got approved from Engineer - in - charge before use. |
| 99 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 810 gms. The sample quality & series should be got approved from Engineer - in - charge before use. |
| 100 | Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 690 gms. The sample quality & series should be got approved from Engineer - in - charge before use. |
| 101 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use. |
| 102 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use. |
| 103 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 104 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.The sample quality & series should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals. |
| 105 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 106 | For 455 mm x 610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 107 | For 500 mm x 700 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 108 | For 600 mm x 850 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 109 | Extra for depth beyond 45 cm of brick masonry chamber including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 110 | Inside dimensions 455 cm x 610 cm and 45 cm deep for single pipe line : |
| 111 | Inside dimensions 500 cm x 700 cm and 45 cm deep for pipe line with one or two inlets : |
| 112 | Inside dimensions 600 cm x 850 cm and 45 cm deep for pipe line with three or more inlets: |
| 113 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. Internal work - Exposed on wall. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge including carriage of material with in all leads, lifts and other incidentals. |
| 114 | 15 mm nominal outer dia Pipes. |
| 115 | 20 mm nominal outer dia Pipes. |
| 116 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge as required Concealed work, including cutting chases and making good the walls etc. including carriage of material with in all leads, lifts and other incidentals. |
| 117 | 15 mm nominal outer dia Pipes. |
| 118 | 20 mm nominal outer dia Pipes. |
| 119 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge for external work including carriage of material with in all leads, lifts and other incidentals. |
| 120 | 15 mm nominal outer dia Pipes. |
| 121 | 20 mm nominal outer dia Pipes. |
| 122 | Providing and fixing 20 mm PPR unions. The sample quality should be got approved from Engineer - in - charge before use. |
| 123 | Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x 1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe). complete including carriage of material with all leads ,lifts and other incidentals. |
| 124 | External work work for providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 125 | 15 mm dia nominal bore. |
| 126 | 20 mm dia nominal bore. |
| 127 | Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the walls and floors complete. |
| 128 | 110 mm x 90 mm |
| 129 | 110 mm x 75 mm |
| 130 | Providing and fixing PVC Poly plast sewerage & drain pipe of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete including carriage of material with in all leads, lifts and other incidentals. |
| 131 | 75 mm dia. |
| 132 | 110 mm dia. |
| 133 | Providing and fixing PVC Poly plast sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme / centimeter metre square) fitting & accessories including filling the joints with approved adhesive complete. \\"PVC Plain Bend\\" |
| 134 | 75 mm dia. |
| 135 | 110 mm dia. |
| 136 | Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. \\"PVC Door Bend\\" |
| 137 | 75 mm dia. |
| 138 | 110 mm dia. |
| 139 | Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. \\"PVC Collar\\" |
| 140 | 75 mm dia. |
| 141 | 110 mm dia. |
| 142 | Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. \\"PVC Plain Tee\\" |
| 143 | 75 mm dia. |
| 144 | 110 mm dia. |
| 145 | Single equal branch of required with oval access door insertion rubber washer 3mm thick bolts and nuts. \\"PVC Door Tee\\" |
| 146 | 75 mm dia. |
| 147 | 110 mm dia. |
| 148 | Providing and fixing PVC Poly plast sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. \\"PVC Y Tee\\" |
| 149 | 75 mm dia. |
| 150 | 110 mm dia. |
| 151 | Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. \\"PVC Offset\\" |
| 152 | 75 mm dia. |
| 153 | 110 mm dia. |
| 154 | Providing and fixing sewerage & drain pipe line fitting of working pressure not less than 4 kgf/ centimeter metre square (Four kilogramme centimeter metre square) including filling the joints with approved adhesive complete. \\"PVC Cowel\\" |
| 155 | 75 mm dia. |
| 156 | 110 mm dia. |
| 157 | Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixd to wooden cleats with C.P. Brass screws complete including carriage of material with in all leads, lifts and other incidentals. |
| 158 | Providing and fixing C.P. Brass towel rail of size 600 mm x 20 mm complete with C.P. Brass brackets fixed to wooden plugs with CP brass screws complete including carriage of material with all leads and lifts. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysSep 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender