Tender For Construction Of Road Works Under Pradhan Mantri Gram Sadak Yojana I.E. Pmgsy-Iv (Batch-I) L323-Pwd Road To Bandhapai
Tender Value
66.33 Lakhs
Estimated cost
Bid Submission
18 Sep 2026
13 days left
EMD
1.32 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Rayagada → Odisha
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of Road Works Under Pradhan Mantri Gram Sadak Yojana I.E. Pmgsy-Iv (Batch-I) L323-Pwd Road To Bandhapai
BOQ
| Sl. No. | Item Description |
| 1 | BT Road Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness as per MORD technical specification cluase 201.1. & direction of Engineer-in-charge (by manual means). |
| 2 | Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking theunserviceable material with all lifts and lead of 1000m as per clause202.1of MORD specification for Rural roads & as per direction of the Engineer-in-charge.. |
| 3 | cement concrete |
| 4 | Rainforced cement concrete |
| 5 | Brick / Stone Masonary |
| 6 | Above 600 mm dia to 900 mm dia |
| 7 | Above 900mm dia |
| 8 | Construction of embankment with approved material obtained from borrow pits with all leads and lifts, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 by mechanical means as per Technical Specification Clause 301.5 and as per the direction of the Engineer in charge. |
| 9 | Excavation for roadway in hard soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, inaccordance with requirements of lines, grades and cross sections, and transporting to the embankement location with a lift of up to 1.5m and lead up to 1000m as per techincal specification clause 302.3 of MoRD and as per direction of Engineer-In-Charge. |
| 10 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 and as per the direction of the Engineer in charge. |
| 11 | Excavation for roadway in hard rock (blasting prohibited) by Mechanical Means with rock breakers including breaking rock, loading in tippers and disposal with a lift upto 1.5 m and lead upto 1000 metres, trimming bottom and side slopes in accordance with requirements of lines, grades and cross- sections by mechanical means as per Technical Specification Clause 302.3.5 and as per the direction of the Engineer in charge. |
| 12 | Excavation for roadwork including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with all lifts and lead upto 1000 m as per Technical Specification Clause 302.3 and as per the direction of the Engineer-in-chargeExcavation in Hard Rock (Requiring blasting) |
| 13 | Construction of soil aggregate sub-base by providing well graded material of nominal maximum size grading 20 mm as per table 2.3 of IRC sp 77 2008, spreading in uniform layers with tractor mount appropriate grading arrangement on prepared surface, mixing by mix in place method at OMC with tractor mount appropriate rotavator attachment and compacting with three wheeled 80- 100 KN static roller to achieve the desired density as per the specification contained in para 2.2.3.6 and 3.7 of IRC sp 77 2008 and as per the direction of Engineer In Charge |
| 14 | Providing, laying, spreading and compacting stone aggregates of specific sizes to Water Bound Macadam specification including spreading in uniform thickness hand packing, rolling with three wheel 80-100 KN static roller in stages to proper grade & camber, applying & brooming, crushable screening / stone screening to fill up the interstices of coarse aggregate, watering & compacting to the required density as per Clause 405 of MORD Specification for Rural roads including cost,conveyance,royalty, taxes, labour and T&P required for the work and as per direction of Engineer in Charge. |
| 15 | W.B.M G-II |
| 16 | W.B.M G-III |
| 17 | Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 of MoRD for low porosity surface. and as per direction of Engineer-In-Charge. |
| 18 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503 of MoRD. and as per direction of Engineer-In-Charge. |
| 19 | Providing, laying and rolling of close-graded premix carpet (Mix Seal Surfacing) of 20 mm thickness composed of 13.2 mm to 0.9 mm (type-B) aggregates using S-65 penetration grade bitumen @ 19 kg/10 sqm to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable hot mix plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed as per Technical Specification Clause 509 of MoRD and as per direction of Engineer-in-Charge |
| 20 | Fine dressing &Turfing including transportation of turfs by mechanical means with all leads & lifts and placing of turfs in position and ramming with thapies including watering and cost of labour & all materials etc. complete as per direction of Engineer - in - charge. |
| 21 | CROSS DRAINAGE WORKSEarthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 of MoRD including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material and as pr the direction of the Engineer in charge |
| 22 | Fillling sand in foundation trenches as per drawing and technical specification Clause 305.3.9 & as per direction of Engineer in charge |
| 23 | Prividing & laying Plain Cement Concrete M-15 Nominal Mix (1:2.5:5)in open foundation as per drawings & Technical Specification clauses 802,803,1202 & 1203 of MORD and as per direction of Engineer-In-Charge. |
| 24 | Prividing & laying Plain Cement Concrete M-15 Nominal Mix (1:2.5:5) in substructure as per drawings & Technical Specification clauses 802,804, 805,806, 807,1202 & 1204 of MORD and as per direction of Engineer-In-Charge. |
| 25 | Construction of un-reinforced, plane cement concrete pavement of desired, thickness as per thee design, over a prepaired sub base, with 43 grade cement or any other type as per cluse 1501.2.2 M30 (Grade), course and fine aggregate conforming to IS:383, maximum size of course aggregate not exceeding 25mm, mixed in a concrete mixture of not less the 0.2 cum capacity and appropriate weight batcher using the approved mix design, laid in approved fixed side form work (steel channel, laying and fixing of 25mm micro thick polythene film, wedges steel plates including levelling the form work as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrator and finished in the contineous operation includion provision of construction and expansion, construction joint, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixture as approved, curing of concrete slabs for 14-days, water finishing to lines and grade as per drawing and Technical Specification cluse 1501.panels are to be made by cuttion grooves of 3 to 5 mm thick and 25 to 30 mm deep in CC Slab. The grooves are to be filled with VG-30 Bitumen with a spray of fine sand at top. |
| 26 | Prividing & laying Reinforced Cement Concrete M-25 in Open Foundation as per drawings & Technical Specification clauses 802,803, 1202, 1203 of MORD and as per direction of Engineer-In-Charge. |
| 27 | A) Superstructure |
| 28 | Supplying, fitting and placing HYSD bar reinforcement in substructure complete as per drawings and technical specification Clauses 1002, 1010 & 1202 and as per the direction of the Engineer in charge |
| 29 | Providing and laying reinforced cement concrete pipe NP3 for culverts on cement concrete bedding including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. and as per the direction of the Engineer in charge |
| 30 | 600 mm dia HPC (Single row) |
| 31 | 1000 mm dia HPC (Single row) |
| 32 | 1200 mm dia HPC (Double row) |
| 33 | Providing and laying boulder appron for bed protection with stone boulders of minimum size and weight as per table 1300.1,no fragment weighing not less than 25kg laid dry complete as per drawing and Technical Specification clause1301. |
| 34 | Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 and as per the direction of the Engineer in charge |
| 35 | ROAD APPURTENANCESProviding and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 and as per the direction of the Engineer in charge |
| 36 | Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing as per Clause 1701.2.2 of MoRD and as per direction of Engineer-In-charge |
| 37 | Providing and fixing of typical Citizen Informatory sign board with Logo as per MoRD specification and drawing. Two nos MS Plate of 1.6 mm thick, top and bottom plate duly welded with MS flat iron 25mm x 5m size on back on edges. The flat iron frame of both plates with be welded to 2 Nos. 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. Lettering and printing arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.00 of MoRD and as per direction of Engineer-In-Charge. |
| 38 | Supplying and installing of measurement stones including painting, lettering in accordance with the specifications and as approved by the engineer and as per direction of Engineer-In-Charge and as per clause 1703 of MoRD. |
| 39 | i) 200 mtr Stone |
| 40 | Reinforced Cement Concrete M15 grade boundary pillars / local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification Clause 1704. |
| 41 | Construction fo RCC guard posts of 200 mm dia M15 grade cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC posts not to exceed 1 in 500 as per drawing and Technical Specification Clause.and as per the direction of the Engineer-in-charge |
| 42 | Maintenance Routine Maintenance after completion of construction works 1st Year |
| 43 | 2nd Year |
| 44 | 3rd Year |
| 45 | 4th Year |
| 46 | 5th Year Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysSep 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender