Tender For Supply Of Pet Preforms For 1000Ml Packaged Drinking Water Bottle For Our Plant At Aruvikkara Thiruvananthapuram And At Thodupuzha Idukki

Sharing tender

Tender for Supply Of Pet Preforms For 1000Ml Packaged Drinking Water Bottle For Our Plant At Aruvikkara Thiruvananthapuram And At Thodupuzha Idukki , Appendix A , Supply Of 28 Mm Neck Size Pet Preforms As Per The Following Technical Specifications: Weight: 19.5 Gms ± 0.20 Gms, The Preforms For 1000Ml Drinking Water Bottle. Raw Material: Polyethylene Terepthalate Resin With Iv 0.80+/- 0.02. Only Virgin Raw Material Shall Be Used . Proof For The Quality Shall Be Produced, If Asked For. Material (Pet-Resin) Should Be As Per Bis Standards; 12252:1987, 12229:1987 As Suitable For Packing Mineral Water/ Food Stuff. Overall Migration Should Be As Per Is- 14543: 2004. Neck: 28Mm, Three Start / Half Twist Thread, Colour Of Preform: Clear. Length: 110 Mm ± 2 Mm, Max. Weight. Weight: 13.5 Gms +/ - 0.20 Gms , Max. Neck: 28 Mm, Three Start/ Half Twist Thread. Length 74 Mm +/- 2Mm, Max Deviation, However Preforms With Minus Grammage Deviation In 1000Nos Shall Be Limited To 5% Foreign/ Black Particles: Preforms Should Be Fully Free From Any Foreign Or Black Particles. Flashes Are Not Acceptable. Fused Preforms: Preforms Should Not Be Stuck Together. Crystallinity: Crystallinity At The End Of The Preform Shall Not Exceed More Than 10Mm From The Gate. Bubbles Are Not Acceptable. Scratches: Scratches Should Not Be Visible To The Naked Eye. Acetaldehyde Content 3 Ppm. The Product Should Be In Line Or Superior In Quality Comparing With The Leading Soft Drink And Mineral Water Manufacturers. It Is Desirable To Have Plastic Bottles Made Of Polyethylene Terepthalate Resin Containing Only A Very Low Lwvel Of Aldehyde Or Of Any Other Material That May Give A Taste To A Drink Bottled Therin. Cost Shall Be Inclusive Of All Conveyance And Delivery At The Factory At Aruvikkara And Shall Be Inclusive Of All Unloading Charges At Site. , Supply Of 28 Mm Neck Size Pet Preforms As Per The Following Technical Specifications: Weight: 19.5 Gms ± 0.20 Gms, The Preforms For 1000Ml Drinking Water Bottle. Raw Material: Polyethylene Terepthalate Resin With Iv 0.80+/- 0.02. Only Virgin Raw Material Shall Be Used . Proof For The Quality Shall Be Produced, If Asked For. Material (Pet-Resin) Should Be As Per Bis Standards; 12252:1987, 12229:1987 As Suitable For Packing Mineral Water/ Food Stuff. Overall Migration Should Be As Per Is- 14543: 2004. Neck: 28Mm, Three Start / Half Twist Thread, Colour Of Preform: Clear. Length: 110 Mm ± 2 Mm, Max. Weight. Weight: 12.5 Gms +/ - 0.20 Gms , Max. Neck: 28 Mm, Three Start/ Half Twist Thread. Length 74 Mm +/- 2Mm, Max Deviation, However Preforms With Minus Grammage Deviation In 1000Nos Shall Be Limited To 5% Foreign/ Black Particles: Preforms Should Be Fully Free From Any Foreign Or Black Particles. Flashes Are Not Acceptable. Fused Preforms: Preforms Should Not Be Stuck Together. Crystallinity: Crystallinity At The End Of The Preform Shall Not Exceed More Than 10Mm From The Gate. Bubbles Are Not Acceptable. Scratches: Scratches Should Not Be Visible To The Naked Eye. Acetaldehyde Content 3 Ppm. The Product Should Be In Line Or Superior In Quality Comparing With The Leading Soft Drink And Mineral Water Manufacturers. It Is Desirable To Have Plastic Bottles Made Of Polyethylene Terepthalate Resin Containing Only A Very Low Lwvel Of Aldehyde Or Of Any Other Material That May Give A Taste To A Drink Bottled Therin. Cost Shall Be Inclusive Of All Conveyance And Delivery At The Factory At Thodupuzha And Shall Be Inclusive Of All Unloading Charges At Site.