Tender For Special Repairs To Gate And Parking Area For Air Force School At Afac Coimbatore
Tender Value
23.75 Lakhs
Estimated cost
Bid Submission
23 Sep 2026
17 days left
EMD
47500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Coimbatore → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Gate And Parking Area For Air Force School At Afac Coimbatore
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed. |
| 2 | Returning ,filling in ,including spreading ,levelling,watering and well ramming in layers not exceeding 25cm in hard dense soil complete all as specified and directed. |
| 3 | Removing surplus excavated soil to a distance exceeding 5 km but not exceeding 15 km and depositing where directed |
| 4 | Material & Labour for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed |
| 5 | Material & Labour for Plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations ,fillling and mass concrete complete all as specified and directed |
| 6 | Demolition of reinforced cement concrete in other than ground floors landings, columns and similar work (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 7 | Material & Labour for RCC design mix M-25 (20mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed |
| 8 | Material & Labour for RCC design mix M-25 (20mm graded aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed |
| 9 | Material & Labour for flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete complete all as specified and directed |
| 10 | Material & Labour for flat formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete complete all as specified and directed. |
| 11 | Material & Labour for TMT bars 10 mm dia over cut to length,bent to shape required, including cranking ,bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed |
| 12 | All as above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders |
| 13 | Material & Labour for brick work with flyash bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 complete all as specified and directed. |
| 14 | Material & Labour for Rendering with WPC in CM 1:4, 15mm thick on othe than fair faces of brick work or concrete surfaces all as specified and directed. Note : WPC shall be measured and paid separately |
| 15 | Supply only Intergral waterproofing compound |
| 16 | Material & Labour preparation newly plastered of wall surfaces and applying two coats of acrylic smooth exterior paint of required shade (applied @ 1.67ltr/10 Sqm) over and including priming coat of exterior primer @2.20 Kg/10 Sqm) all as specified . |
| 17 | Supply & Fixing for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 18 | Supply & Fixing for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed. |
| 19 | Supply & Fixing for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 20 | S &F Granite 20mm thick work for wall lining (veneering to wall) 12mm thick in cement mortar(1:3) and pointing with white cement (1:2) using marble dust withadmixture of pigment to match with shade of granite complete all as specified and directed. |
| 21 | Surface excavation not exc 30 cm and averaging 15 cm deep and getting out in Hard/Dense soil, complete all as specified and directed. |
| 22 | Material & Labour for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface |
| 23 | M & L for Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in CM 1:4 |
| 24 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 25 | Supply & Fixing for Chequered cement concrete tiles 300 x300 x 25mm/ 200 x 200 x 25 mm thk, set, jointed and pointed in neat cement slurry in floors with white cement and pigments complete all as specified and directed. |
| 26 | Supply & Fixing for heavy duty parking tiles 300 x300 x 10mm, laid and and jointed complete all as specified and directed complete all as specified and directed. |
| 27 | M&L for Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in any type of soil complete all as specified and directed. |
| 28 | M&L for cement concrete Type B2 1:2:4 (40mm graded aggregates) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases), complete all as specified and directed. |
| 29 | S & F of Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-240 complete all as specified and directed. |
| 30 | Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and directed. |
| 31 | Material & Labour for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 32 | Supply & Fixing for Plain, galvanised, mild steel sheeting 1 mm thick, in ridge & valley gutters (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed. |
| 33 | Supply & Fixing in repairs 110mm dia PVC (SWR) pipe single sockted in any length with rubber ring joints fixed to wall with clamp complete all as specified and directed. |
| 34 | S&F 110mm radius PVC (SWR) bends complete all as specified and directed. |
| 35 | Material & Labour for plain cement concrete 1;4:8, type D-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified and as directed. |
| 36 | Demolition of brick work built in cement mortar or cement lime mortar complete all as specified and directed. |
| 37 | Material & Labour for Brickwork with sub-class 'B' bricks (old size), straight or curved on plan exceeding. 6m in mean radius, built in cement mortar 1:6 including flush pointing to hidden surfaces in same mortar as work proceeds, complete all as specified and directed. |
| 38 | Material & Labour for PCC 1:3:6, type C1 (using 20 mm graded stone aggregate) for coping and benching inside the manholes including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed. |
| 39 | Taking down cement or cement lime plaster any description on brick or stone walls, etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed |
| 40 | Material & Labour for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick wall surfaces, finished even and smooth with out using extra cement complete all as specified and directed. |
| 41 | Returning, Felling Including spreading, levelling, watering & well ramming in layers not exceeding 25 cm thick in any type of soil, complete all as specified and directed. |
| 42 | Removing excavated materials to a distance not exc. 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 43 | Material & Labour Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. |
| 44 | Material & Labour for Providing Precast Reinforced cement concrete 1:2:4 type B-I (using 20mm graded crushed stone aggregate) as in manhole covers, set in cement mortar 1;4 including necessary form work and moulds complete all as specified and as directed. (Note: Steel reinforcement shall be measured and paid for separately under respective item.) complete all as specified and directed. |
| 45 | Supply & Fixing for Framed work such as grills, grating, etc. with ends of bars shouldered and/or riveted, or forged into spikes; frmed balusters, walk ways, railings, framedwork of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 46 | Supply & fix 610 mm dia CONSEC-ZAL super Razor punched Barb Tape (SRBT) Aluminium base helix coil with and including necessary GI fixing clips for securing complete all as specified and as directed with following specifications :- (i) Dia of coil (unstretcherd)- 610 mm (ii) No.of circles -51 turn per coil (iii) Weight of each coil with hessain pack- 8.50 Kg (+0.50Kg) (iv) Coverage per coil- 8 RM (v) Central core wire - Made from 2.60 mm dia GI-HTSS wire as per IS-4454 galvanised as per IS-2629 (vi) Razor punched strip Razer punched tape is CONSEC-ZAL stell comprising of aluminium base with zinc alloy@150 gm/Sqm conforming to ASTM-A 792/A-792M with additional primer treated of Epoxy/ polyuretherane and final paint top coat of calicified green shade (BSL-139) by Hot dipping process all as specified and as directed. Note- Runing lenght of the wall shall be measured for the payment purpose. |
| 47 | Dismantling of structural steel work including doors, gates but excluding framed truss etc.complete all as specified and directed. |
| 48 | Material & Labour for Framed work using mild steel having grade of GDE Fe- 410W (Gde E-250) Quality A as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge. |
| 49 | Material & Labour for preparing new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 50 | Providing, fabricating and fixing double leaf gate shutters made of SS 304 grade stainless steel of approved design and size, comprising outer frame of 75×50×2 mm thick rectangular SS304 hollow section and inner supporting framework of 40×40×1.6 mm thick square SS 304 hollow section, including providing and fixing 3 mm thick MS CNC laser cut sheet in approved pattern with matte black powder coated background, and fixing of 1.5 mm thick SS 304 mirror finish CNC laser cut logo/pattern (including Air Force insignia) over the base panel, complete with necessary backing supports, stiffeners and fixing arrangements. The work includes providing and fixing heavy duty SS 304 barrel/bullet hinges of 150 mm length, 25 mm diameter, 3 mm body thickness with solid SS pin of 10–12 mm diameter, minimum 6 numbers, properly aligned and fixed to existing RCC/steel columns. The work also includes providing and fixing locking arrangement comprising SS drop bolt of 300 mm length and 16 mm diameter at bottom, complete with necessary sockets/receivers, all fittings and fixtures.All welding shall be carried out by TIG welding process with proper grinding and smooth finish. The exposed SS surfaces shall be finished in mirror polish (No.8 finish), and MS surfaces shall be properly prepared and powder coated in approved matte black shade with minimum coating thickness of 60–80 microns. The item includes all materials, labour, consumables, tools & tackles, loading/unloading, transportation, alignment, installation and all incidental charges, complete in all respects as directed by Engineer-in-Charge |
| 51 | Removal of debris/building material out side the campus including loading and unloading, etc to a distance exc 5Km but n exc 10 km out side the MD land complete all as specified and directed. Note:- Location and permission of depositing the building materials/debris disposal outside the MD land shall rest with contractor at his own arrangement. |
AI Tender Summary
Tender Timeline
Sep 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysOct 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender