Tender For Special Repairs To Distribution Pipe Line And Connected Items At Rajbari Pump House At Dimapur
Tender Value
43 Lakhs
Estimated cost
Bid Submission
23 Sep 2026
5 days left
EMD
86000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Wokha → Nagaland
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Distribution Pipe Line And Connected Items At Rajbari Pump House At Dimapur
BOQ
| Sl. No. | Item Description |
| 1 | Supply, laying in trenches, connecting/jointing, testing and commissioning of DN 100 mm Ductile Iron Pressure pipes, centrifugally cast (spun), Class \\"K-9\\" with socket and spigot ends conforming to IS-8329 in standard length suitable for Push-On Rubber gasket jointing with inside cement mortar lining and with black bitumen external coating including taking up old CI water mains (including all fittings), with spigot and socketed ends jointed with run lead joints including burning out joints and recovering leads and removing unserviceable pipe lines from site complete, all as specified and as directed by Eng-in-charge.Note :(i) Necessary PCC supports for pipe line will be measured and paid seperately.(ii) DI fittings shall be measured and paid seperatly respective items here-in-after.(iii) Rate quoted is inclusive of site clearance i.e vegetation clearance/ jungle clearance. (iv) Rates quoted by tenderer including jointing material like Rubber gasket etc, including necessary welding work.(v) Earthwork shall be measured and paid separately |
| 2 | Supply, laying, in repairs GI tubing medium grade of size 100 mm bore with and including all fitting in trenches complete all as specified and as directed. |
| 3 | Supply, laying, in repairs GI tubing medium grade of size 80 mm bore with and including all fitting in trenches complete all as specified and as directed. |
| 4 | Supply, laying, in repairs GI tubing medium grade of size 50 mm bore with and including all fitting in trenches complete all as specified and as directed. |
| 5 | Supply, laying, in repairs GI tubing medium grade of size 40 mm bore with and including all fitting in trenches complete all as specified and as directed. |
| 6 | Supply, laying, in repairs GI tubing medium grade of size 25 mm bore with and including all fitting in trenches complete all as specified and as directed. |
| 7 | Supply, laying, in repairs GI tubing medium grade of size 20 mm bore with and including all fitting in trenches complete all as specified and as directed. |
| 8 | S&F in repairs GI tubing medium grade of size 100 mm bore with and including all fitting fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 9 | S&F in repairs GI tubing medium grade of size 80 mm bore with and including all fitting fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 10 | S&F in repairs GI tubing medium grade of size 50 mm bore with and including all fitting fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 11 | S&F in repairs GI tubing medium grade of size 40 mm bore with and including all fitting fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 12 | S&F in repairs GI tubing medium grade of size 25 mm bore with and including all fitting fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 13 | S&F in repairs GI tubing medium grade of size 20 mm bore with and including all fitting fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 14 | Supply, install, connecting and testing in repairs/replacement of sluice valve, of size 100mm dia,class PN-1.6 double flanged with CI body, wheel operated and brass spindle and gun metal nuts etc.,ISI marked conforming to IS- 14846-2000,fixed in position including jointing materials i.e. rubber gaskets, nuts, bolts, washers complete all as specified and as directed. |
| 15 | Supply, install, connecting and testing in repairs/replacement of sluice valve, of size 80mm dia,class PN-1.6 double flanged with CI body, wheel operated and brass spindle and gun metal nuts etc.,ISI marked conforming to IS- 14846-2000,fixed in position including jointing materials i.e. rubber gaskets, nuts, bolts, washers complete all as specified and as directed. |
| 16 | S&F in repairs/replacement, new butterfly valve of size 100 mm dia cast iron body ISI marked conforming to 14846, class PN-1.6, single eccentric, double flanged short body type with all fittings, nuts bolts and washers and necessary rubber gaskets complete all as specified and as directed. |
| 17 | S&F in repairs/replacement, new butterfly valve of size 80 mm dia cast iron body ISI marked conforming to 14846, class PN-1.6, single eccentric, double flanged short body type with all fittings, nuts bolts and washers and necessary rubber gaskets complete all as specified and as directed. |
| 18 | S&F Non Return Valve of size 100 mm dia cast iron body, as per IS-5312, class PN-1.6, double flanged with nitrile reinforced ball fittings with ISI mark and fixed in position with rubber gasket joints, bolts nuts and washers etc including taking out old unserviceable Non return valve complete all as specified and as directed. |
| 19 | S&F Non Return Valve of size 80 mm dia cast iron body, as per IS-5312, class PN-1.6, double flanged with nitrile reinforced ball fittings with ISI mark and fixed in position with rubber gasket joints, bolts nuts and washers etc including taking out old unserviceable Non return valve complete all as specified and as directed. |
| 20 | S&F in repairs/replacement, Cast Iron foot valves flanged type of size 150 mm bore, ISI marked (flange drilling) with necessary rubber packing nuts, bolts and washers complete all as specified and as directed. |
| 21 | S&F in repairs/replacement, Cast Iron foot valves flanged type of size 100 mm bore, ISI marked (flange drilling) with necessary rubber packing nuts, bolts and washers complete all as specified and as directed. |
| 22 | S&F Ductile Iron fittings, specials (K-12) such as bends, tapers, collars, reducers, tee pieces (single or double branch) any type, angle/radius and straight connecting pieces etc (ISI marked) conforming to IS-9523 for flanged/socket and spigot ends suitable for DI pipe upto 200 mm bore complete all as specified and as directed. |
| 23 | M&L for MS fitting/specials suitable for 80mm to 200mm dia pipes such as bends, , tappers, etc any type and angle and straight connected pieces any type joint all flange ends including necessary cutting,welding, bending , drilling holes for bolts, in any shape or size as indicated or directed including necessary jointing materials such as nut bolts washers packings and welding including dismantling existing fittings of any description and testing for leekage etc to the entire satisfaction of Engineer-in-Charge complete all as specified and as directed. |
| 24 | M&L for construction of brick masonnary with full brick wall chamber size of 1200x1200x1200 mm (internal diemension) with earth work on any type of soil , PCC (1:3:6) type C-2 (using 20mm graded stone aggregate ) as in foundation concrete bed/ floor coping , sub class 'B' bricks (using old size burnt bricks) built in CM (1:4), 15mm thick rendering in CM (1:4) on internal and exposed external surfaces, external plaster shall be upto 15 cm below ground level and mixed with water proofing compound @ 3% by weight of cement , flush pointed in same mortar as work proceeds , 75mm thick PCC coping all around (1:3:6) type C-2 (using 20mm graded stone aggregate ) , flooring shall 40mm thick PCC M-15 (Nominal Mix ) laid over 75mm thick hard core. Top cover shall be made out of 3.15mm thick MS black sheet fixed in angle iron frame made out of angle iron size 45x45x6mm with two numbers of hinges on one side and locking arrangement at other side complete including painting with two coats of synthetic enamel paint over and including a coat of redoxide primer complete all as specified and directed including demolition of old existing Abandoned valve pits complete all as specified and as directed. |
| 25 | M&L for construction of brick masonnary with full brick wall chamber size of 900x900x900 mm (internal diemension) with earth work on any type of soil , PCC (1:3:6) type C-2 (using 20mm graded stone aggregate ) as in foundation concrete bed/ floor coping , sub class 'B' bricks (using old size burnt bricks) built in CM (1:4), 15mm thick rendering in CM (1:4) on internal and exposed external surfaces, external plaster shall be upto 15 cm below ground level and mixed with water proofing compound @ 3% by weight of cement , flush pointed in same mortar as work proceeds , 75mm thick PCC coping all around (1:3:6) type C-2 (using 20mm graded stone aggregate ) , flooring shall 40mm thick PCC M-15 (Nominal Mix ) laid over 75mm thick hard core. Top cover shall be made out of 3.15mm thick MS black sheet fixed in angle iron frame made out of angle iron size 45x45x6mm with two numbers of hinges on one side and locking arrangement at other side complete including painting with two coats of synthetic enamel paint over and including a coat of redoxide primer complete all as specified and directed including demolition of old existing Abandoned valve pits complete all as specified and as directed. |
| 26 | M&L for Earthing complete with GI earth plate 60cm x 60cm x 6mm thick electrode, burried directly in ground (earth pit not less than 2.70 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to GI strip 32X6mm size up to test point by means of nuts, bolts, check nuts and washers of copper ,including excavation and earth work, PCC (1:3:6) type C-1 pit, GI pipe 15mm dia medium grade for watering arrangement and 40mm bore dia GI pipe medium grade for protection of earth lead, 50mm thick RCC (1:2:4) type B-1 cover, reinforced with 8mm dia TMT bars @ 15cm C/C both ways and with handle made out of 10mm dia bars, funnel, wire mesh etc. as shown in electrical Plate No. 03 of SSR Part-I connected to earthing test point including taking down old unserviceable material and testing on completion including dismantling of old earthing complete all as specified and as directed.Note : (a) The earthing value of each earthing pit should be below 1 Ω (Ohm)(b) Copper strip beyond 7.5 m shall be measured and paid seperately. |
| 27 | Supply and laying 32X6 mm GI strip at 0.50 metre below ground/fixed with cremics /porcelain spacers,including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) including taking down old strip complete all as specified and as directed . |
| 28 | S & F for Pressure gauge 8'' dial type meter range 0-14 Kg/sqcm in delivery line of pumpset etc including removal of old unserveceable one completed all as specified and directed by Engr-In-Charge. |
| 29 | M& L for Mild steel Base plate made out of stractural steel i.e MS channel heavy duty as per manufacture design and proper alignment including and necessary cutting, welding as required suitable for pump set as per existing base plate as conforming to Fe.290, Gde-E-165,and connection with nut and bolts, including painting with two coats of synthetic enamel black colour paint over and including a coat of Zinc red oxide primer to the base plate including dismantling of old unsv one complete all as specified and directed by Engr-in-Charge. |
| 30 | M&L for Pump set details information sign board made out of 3.0 mm thick acrylic sheet of size 600 mm x 900 mm for printing the details of Centifugal pump set including Motor details, DG Sets etc for Water supply installation of Pump House, Filtration Plant, Electrical Sub Station with navy Blue Background & white colour letters suitable for 40 mm width of each letter existing information & other information as provided by Engr-in- Charge including necessary fixing arrangements to the wall of pump house with suitable screws including taking down old unsv board complete all as specified and directed by Engr-in-Charge. |
| 31 | S&F in repairs Perforated cable tray GI 1.6mm thick of size 100mm x 50mm for cable laying alongwith nylon tie/ clip duly fixed with proper clamping material complete all as specified and as directed. |
| 32 | Supply, laying, jointing, testing 16 sqmm,3 core, PVC Insulated and PVC Sheathed Industrial Copper Conductor cable, 1100 Volts grade laid in trenches, pipe, ducts,cable tray with cable tie properly including electric connection taking down existing damaged cable complete all as specified and directed. |
| 33 | Supply, laying, jointing, testing 10 sqmm,3 core, PVC Insulated and PVC Sheathed Industrial Copper Conductor cable, 1100 Volts grade laid in trenches, pipe, ducts,cable tray with cable tie properly including electric connection taking down existing damaged cable complete all as specified and as directed. |
| 34 | Supply, installation, testing and commissioning of indoor type single door Front & Back Openable LT Panel of suitable shape & size to accommodate the following accessories,made out of outer Body & Door 2mm and Inner Door & Cover 2mm thick CRCA sheet with modular hinges, fabrication with 7 tanks process, IP-55 with coloured insulation sleeve, rubber, insulator indoor type totally enclosed weather dust and vermin proof as per IS with front & Back opening suitable aldrop bolt locking arrangement with insulators, including connecting incoming and outgoing cables necessary PCC (1:3:6) in foundation and made out of 50 x 50 x 6 mm angle iron grouted at ground above 45 cm from ground level and 30 cm in PCC below ground level Comprising the following complete all as specified and as directed:- Please Enable Macros to View BoQ information |
| 35 | Supply, installation, testing and commissioning of indoor type single door Front & Back Openable LT Panel of suitable shape & size to accommodate the following accessories,made out of outer Body & Door 2mm and Inner Door & Cover 2mm thick CRCA sheet with modular hinges, fabrication with 7 tanks process, IP-55 with coloured insulation sleeve, rubber, insulator indoor type totally enclosed weather dust and vermin proof as per IS with front & Back opening suitable aldrop bolt locking arrangement with insulators, including connecting incoming and outgoing cables necessary PCC (1:3:6) in foundation and made out of 50 x 50 x 6 mm angle iron grouted at ground above 45 cm from ground level and 30 cm in PCC below ground level Comprising the following complete all as specified and as directed:- Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysSep 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender