Tender For Lis Delina Ghat- Construction Of Pump House, Sump And Construction Of Cement Concrete Channel From Rd 200-500 Mtrs (Amount Of Work:- Rs 89.36 Lacs)
Tender Value
89.36 Lakhs
Estimated cost
Bid Submission
18 Sep 2026
12 days left
EMD
1.78 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Baramulla → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Lis Delina Ghat- Construction Of Pump House, Sump And Construction Of Cement Concrete Channel From Rd 200-500 Mtrs (Amount Of Work:- Rs 89.36 Lacs)
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil |
| 2 | Dumping stone including cost of stones. in Horizontal on level |
| 3 | Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 4 | Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with: (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 5 | Providing and laying cement concrete in kerbs, steps and the like at or near ground levelincluding curing, excluding the cost of centring, shuttering, and finishing.(1 cement : 2 coarse sand :4 graded stone aggregate 20 mmnominal size) |
| 6 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, buttresses, plinth andstring courses etc. |
| 8 | 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 9 | Structural steel work in single section, fixed with or without connectingplate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 10 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 infoundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 11 | Extra for brick work with common burnt clay bricks/cement concrete bricks insuperstructure above plinth level upto floor five level |
| 12 | Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. complete First class Budloo/Fir wood |
| 13 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete 0.50 mm thick with zinc coating not less than 275 gram/m2 |
| 14 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Kiln seasoned and chemically treated hollock wood |
| 15 | Providing and fixing glazed shutters for doors, windows and clerestory windowsusing 4mm thick float glass panes including ISI marked M.S. pressed butthinges bright finished of required size with necessary screws.Kiln seasoned and chemically treated hollock wood |
| 16 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze ofaverage width for aperture 1.4 mm in both directions with wire of dia. 0.63 mmfor doors, windows and clerestory windows with ISI marked M.S. pressed butthinges bright finished of required size with necessary screws as per direction ofEngineer-in-charge :Kiln seasoned and chemically treated hollock wood |
| 17 | Supply of Bathroom accessory |
| 18 | Handles 16 Nos |
| 19 | Hinges 32 Nos |
| 20 | Trawl bolt 32 Nos |
| 21 | Providing and applying Plaster of Paris putty of 2mm thickness overplastered surface to prepare the surface even and smooth complete |
| 22 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats |
| 23 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.With water thinnable cement primer on wall surface havingVOC content less than 50 grams/liter |
| 24 | Providing and fixing high profile ribbed colore coated roffing on supported structure 0.5mm thick |
| 25 | Providing and fixing 250 mm eaves board of approved quality HDHMR/Exterior Grade BWP plywood, 18 mm thick, fixed to timber/steel roof members with suitable galvanized screws, including primer and two coats of exterior-grade synthetic enamel paint of approved shade, complete in all respects. |
| 26 | Finishing with Deluxe multi surface paint system for interiors andexteriors using primer as per manufacturers’ specifications:Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture |
| 27 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover |
| 28 | Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately) Size of tile 600x600 mm |
| 29 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88gms. |
| 30 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 |
| 31 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.110 mm |
| 32 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. |
| 33 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :510x1040mm bowl depth 250mm |
| 34 | Providing/ laying PVC pipes and accessory jobs |
| 35 | 100m dia |
| 36 | 75mm dia |
| 37 | 25mm dia |
| 38 | Tee,elbow,value,etc |
| 39 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank |
| 40 | Providing /fixing of Trash Guard: |
| 41 | Carriage of material by Mechanical Transport including loading, unloading and stacking up to site of work. |
| 42 | Stone soiling Quarry for an avg. lead of 17 kms |
| 43 | Aggregate. 20mm for an average lead of 35 kms |
| 44 | Aggregate. 40mm for an avg. lead 35 kms |
| 45 | Sand for an Avg. lead 05 kms |
| 46 | Cement for an avg. lead 15 km |
| 47 | Bricks from Budgam for an Avg. lead 60 kms |
| 48 | Carriage of material By Manual Labour including loading, unloading and stacking for lead 100 mtrs |
| 49 | Stone soiling Quarry |
| 50 | Aggregate. 20mm |
| 51 | Aggregate. 40mm |
| 52 | Cement |
| 53 | Mechanical Part :-Providing, Installation, Testing, and Commissioning of single stage submersible pump set with non clogging impeller. The pump to have stationary arrangement and shall be supplied with pump connector /pedestal unit connected to pump support bracket with suitable diaphragm to make a leak proof joint. The pump connector to be fitted / grouted on the sump floor on suitable concrete foundation laid up to the suitable depth as per site requirements (The weight of concrete foundation to be approximately 3 times the weight of pumping unit). Providing and fitting of pump reducer / Expander as per site requirements for proper positioning and connection of the pump with the delivery pipe is included in the job. The Job Further includes complete dewatering of sump for proper installation of the equipment using proper dewatering equipment. The specifications of the pump set are as follows :SPECIFICATION OF UNIT: A) PUMP:- i) Discharge :142 LPS(05cusec) ii)T.D.H :14Mtrs iii) Type : Non Clog end Centrifugal volute type Submersible pump. iv) Solid Handling size ≥ 50mm. v)Speed : 960rpm vi)Pump Efficiency ≥ 63% at duty point vii)Impeller : Stainless Steel impeller with three to four vane design viii)Shaft : Stainless steel ix) Bearings : Roller/Ball bearings. x)Pump Casing : Cast iron, Volute type xi)Sealing : Mechanical double seals independent of Direction of rotation. xii) Acceptable Make : Kirloskar /KSB / M&P / WIPIL / Flow more/ or as approved in EOI SE mechanical I&FC kashmir B)MOTOR:- i)Rating : 50HP ii)speed : 960rpm iii)Rated Voltage : 415±10%Volts,3 phase A.C iv)Rated Frequency : 50±3%HZ v) Class of Insulation : C or above vi)Protection : IP68 or above vii) Efficiency : 90% or above v)Temperature rise : 75° over an ambient of 40°C vii)Bearings a)Type :Ball Bearings b)method of Lubrication :Grease packed maintenance free C)ACCESSORIES: i) Rail guide/Hoist: - Providing, Installation, Testing, and Commissioning of Vertical guide rails two numbers connected to the duck foot pedestal to enable lowering and hoisting the pump with ease, the pump to be guided up to the walk way near the pump house and to be suitably coupled with pedestal with suitable arrangement. (sump depth from working plate form= 18.5 feet) ii)Cable:- Providing, Installation, Testing, and Commissioning 1.1KV grade electric submersible cable having annealed tinned copper conductor, sheathed with rubber and chloroprene elastomeric compound conforming to IS 9968 Part I (40 Mtr/ unit total for two job as 80 mtr) to be laid from two starter to two pumping units. The job includes all cost of material , welding work, modification, Flanges if any required during the fitment of the pumping unit. Note: Manufacturer’s test certificate is mandatory and Third-Party Inspection is mandatory. |
| 54 | Supply, installation, laying and handling of 250 mm dia., 5.6mm thick MS delivery pipe for two pumping unit which includes the charge of fabrication of long radius mitered bends, off sets, welding work, nuts & bolts, washers etc. for the completion of work. (40 Mtr) SPECIFICATIONS:Nominal diameter of pipe = 250 mmOuter Diameter = 273mmThickness of pipe = 5.6 mm Length of each pipe = 4 -6Mtr Pipe manufacturing process = ERW TypeThe job also includes Supply, installation, testing of 250 mm Nominal dia. M.S flanges fabricated out of 16 mm Ms Plate for delivery pipe with nuts, bolts, washers & allied works (20 No’s), Any modification like reducer/ expansion etc required during execution of work shall be arranged within quoted price. The job also include fabrication of Y junction out of 250 mm dia MS pipe and joining one end with existing MS rising main. |
| 55 | Supply, Installation, Testing and Commissioning of 250 mm dia CI Sluice valve for two pumping units of VAG/AVK/ Kirloskar/or equivalent as approved in EOI SE Mechanical I&FC Kashmir of below mentioned specification:. Nominal Dia: 250mm. Body: Cast Iron.. Rating: PN-1.6. Hinge Disc: Cast iron. Hinge Pin: AISI 410. Body Ring: Leaded gun. Disc Face: Natural Rubber. The job also includes providing and fitting of RI cloth, Nuts & Bolts, matching flanges, Washer, welding work for the completion of work for the completion of work. |
| 56 | Supply, Installation, Testing and Commissioning of 250mm dia CI swing-type flanged Non return valve for two pumping unit of VAG/AVK/ Kirloska or equivalent as approved in EOI SE Mechanical I&FC Kashmir of below mentioned specification:. Nominal Dia: 250 mm. Body: Cast Iron.. Rating: PN-1.6. Hinge Disc: Cast iron. Hinge Pin: AISI 410. Body Ring: Leaded gun. Disc Face: Natural Rubber. Included Suitable size of bypass arrangement. with a bolted cover for easy internal maintenance and a renewable nitrile-rubber flapThe job also includes providing and fitting of RI cloth, Nuts & Bolts,matching flamges, washer, welding work for the completion of work. |
| 57 | Internal Travelling Gantry:Design, manufacture, supply, erection, & commissioning of 02-ton capacity with monorail and chain-pulley block suitable for handling a load of 02-ton capacity in both directions i.e. long-travel movement and cross-travel movement.Major components of the crane structure comprise of following items:(a)RUNWAY GIRDERS: fabricated out of ISMB 150 (5 Mtr) (02no), the girder beams fitted on tie-plates as per site requirement. The upper flange of the runway girder is to be fitted with 30x30 mm sq bar along their length over with the end carriage with bridge be fabricated for long movement by means of manually driven gear & pulley mechanics.(b) END CARRIAGE: it shall be fabricated out of ISMC 150 suitably fitted as per requirement, for manufacturing of 02 no end carriages to be rested on runway girder structure by means of 250 mm dia mild steel wheel with gear and pinion mechanism. The end carriages are run by gear mechanism by means of spindle of suitable dia over which the pulley with endless chain to facilitate long travel movement of crane bridge manually through the machine floor.BRIDGE GIRDER: The bridge girder fabricated out of ISMB 300 (5 Mtr) (01 No)as per site requirement. The bridge girder rests over the end carriage fitted as per site requirement.Monorail Block: one unit of 02-ton capacity heavy duty monorail block of globe with ISI mark suitable to operate inside the pump house shall be mounted on the lower flange girder to facilitate the cross-travel movement.Chain pulley Block Manually Operated: one unit of 02-ton capacity globe make shall be provided. Minimum hoist shall be 6.00 mtrs.The job also includes painting of entire structure with two coats of A grade enable yellow paint after proper surface preparation and application of metal primer cot (Make: Asian/Berger/Neurolac). |
| 58 | Fabrication, providing and fitting of working platform which includes providing and fitting of ISMC 100 = 37mtrs, (13' x 5 No + 15'x01 no+5'x08 No) to form a rectangle frame over sump B) Providing and fitting of chequered plate to the rectangular ISMC frame of (width 4 feet , length 17 feet) + (width 4 feet , Length 8 feet) and thickness 6mm. The job also includes the formation of rectangular opening at the requisite spots for installation of suction pipes. The working platform shall be painted with steel primer and two coats of enamel paint of black shade ( make : Asian/ Berger/ Neurolac/equivalent make), Any modification during execution of work shall be carried out as per site requirement. |
| 59 | Sump Gantry Specifications:Fabrication, Providing, Installation and testing of 02 Ton capacity Sump Gantry. The job comprises of the following process and involvement of materials.Specifications: Capacity ………………………………2 Ton Length of beam ………..........................4000 mm Height of vertica post ............................3000mm Column supports for Gantry:Fabrication, Providing and Fitting of 2 No’s column supports for the sump gantry. The column supports shall have to be installed at two sides of the sump on which the beam of the sump Gantry rest. The column supports fabricated out of ISMB 250 . The height of each MS post is 3000 mm. The column supports grouted in cement concrete block of 2’x2’x2.5’ in 1:2:4 mix. The two ends of the column support have provided with MS plate of size 300x300x10mm by way of welding. The plates are drilled with 4 No. of holes so that plate of column supports and plates of I beam shall be joined with the help of nuts and bolts and welding as well. Fabrication and fitting of ladder steps fab. out of ISA 30x30x5mm (1.5 feet long) on both of the vertical columns supports at intervals of 2 feet c/c. The job also include p/f of ISMC 100 channels for support to vertical support ( 10 Mtr) Main I beam of sump Gantry:One No. I beam of size ISMB-300 have laid horizontally on the vertical column supports. The two ends of the I beam have provided with MS plate of size 300x300x10mm by way of welding. The plates also drilled with 4 No. of holes as same of plates of vertical supports and joined with each other with the help of nuts and bolts and welding as well. Movement:The gantry comprises providing/ hoisting of chain block of 02 Ton capacity inbuild over load protection device, with 6 mtr vertical lift on one No. travelling mono rail of 02 Ton capacity. The make of the chain pulley block and mono rail is Globe/elephant or equivalent make with ISI mark. The sump gantry shall be painted with steel primer and two coats of enamel paint of yellow shade for I beam and black shade for vertical supports. (Make: Asian/Berger/Neurolac), The work shall be executed as per the site requirement. |
| 60 | Dismantling Joint:Fabrication, Installation, Testing and commissioning of 250mm dia M.S Dismantling joint three piece type fabricated out of M.S flat plate. The thickness of the body of dismantling joint shall be 6.3mm and thickness of flanges shall be 16 mm thick (06 No.). The job also includes P/F of Nuts, Bolts, Packing, tie rods & Washers required for the completion of work. |
| 61 | Channels:Supply of two no channels fabricated out of ISMC 100 for helping in shifting of electro- mechanical items in load carrier during breakdown of items in future. (20 feet- 10 feet each channel) |
| 62 | Flap Valve:Fabrication, installation, testing & commissioning of M.S flap valve of 250 mm dia. fabricated out of M.S flat plate and thickness of flap plate shall be 16mm. The job includes the charge of hinge, nuts, bolts, washer, D.G set, Welding set, highly skilled labours and other tools & tackles for the completion of work. It also includes applying red oxide primer & then applying two coats of silver paint of reputed make. |
| 63 | Tool set:- |
| 64 | Providing and testing of open ended spanner Set from 6x7 to 34x36- (Taparia/ Skil/ Stanley) |
| 65 | Providing and testing of open ring Spanner Set from 6x7 to 34x36 (Taparia/ Skil/ Stanley) |
| 66 | Providing and testing of screw driver (2 in 1) short length (Taparia/ Skil/ Stanley) |
| 67 | Providing and testing of Screw driver (2 in 1) long (Taparia/ Skil/ Stanley) |
| 68 | Providing and testing ofClub Hammer with handle (01 kg) (Taparia/ Skil/ Stanley) |
| 69 | Providing and testing of Heavy duty Pipe wrench 18\\" (Taparia/ Skil/ Stanley) |
| 70 | Providing and testing of Heavy duty Pipe wrench 36\\" (Taparia/ Skil/ Stanley) |
| 71 | Providing and testing of Grease gun (lever type 450 cubic capacity) |
| 72 | Providing and testing of heavy duty 5.5 meter / 18 feet compact and foldable telescopic ladder having load bearing capacity 150 kg |
| 73 | Providing and testing of hydraulic crimping tool with standard die sizes (min 10 nos.) from 25 to 500 sqmm(Jainsons/ Dowells/ Breeze Shears) |
| 74 | Providing and testing of Digital Altimeter/ barometer altitude range upto 8000 Mtr, accuracy: 1m & pressure accuracy 1mbar (Make: BARIGO / HTC) |
| 75 | Electrical Work: Supply installation, testing and commissioning of 11/0.433kV, 3-phase 100 Kva Distribution Transformers with Bimetallic Terminal Connectors Energy Level-2, Al wound, and with LV Cable Box having detachable Al. Gland plate with LV Bimetallic terminal connection suitable for vertical takeoff , The job also include providing and filling of transformer oil upto the required level of transformer , make : Castrol/Hp/Servo as per IS 335, The Toil shall be filled in Transformer at site |
| 76 | Supply, installation, testing & commissioning of 3.5 core 50 sq mm PVC insulated aluminum cable unarmoured laid from distribution transformer to main control panel of below mentioned specification:Voltage: 1100VInsulation: PVC insulated double sheathed Make of cable: National/Havells Polycab or equivalent make as approved in EOI of SE Mechanical I&FC Kashmir, the cable shall be thimbled at each end. |
| 77 | Supply, Installation, testing & commissioning of single core 50 sq mm PVC insulated double sheathed copper cable to be laid from Main Control Panel to two voltage stabilizersto two starter of below mentioned specification SPECIFICATIONS: Voltage: 1100V Insulation:PVC Insulated double sheathedMake of cable: Gloster/Havells/Finolex/National/as approved in EOI SE Mechanical kashmir Thimble: Dowell Make. |
| 78 | Manufacturing, providing, installation, testing & commissioning of 200 A 3 Phase LT Main control panel. The panel shall be of following specifications & shall compromise of the equipment detailed below: The LT panel shall be totally enclosed free standing type sheet metal enclosed dust and vermin proof, indoor type fabricated out of 14-gauge sheet and painting with suitabe colour, shall be suitable to work on 415+ 10% volts, 50 HZ, and three phase AC supply. The panel shall compromise of one incoming and two independently out going compartments for two pumping units and one auxiliary compartments for local load, Incoming feeder panel shall consist of 200 A incommer, 2 No. 125 A outgoing feeders and an auxiliary feeder. INCOMMING FEEDER: One No. incoming feeder consisting of 200 A Copper bus bar arrangement. The incoming feeder shall house: • 200 Amp 04 pole MCCB with enclosure and having breaking capacity 50 KA at 415 V. The MCCB should shall be four pole and having adjustable thermal & magnetic setting & shall be of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. • Four air insulated copper bus bar of suitable Amps. • One 0- 500 Amp 96 mm sq flash arrestor pattern industrial types CT operated digital ampere meter to register the phase current. • 0-500 Volts voltmeter 96 mm sq digital flash arrestor pattern industrial types CT operated digital volt meter to register the phase voltage. • Digital frequency meter, selector switches, copper wiring & other accessories as per requirement /design should be included. • Three no 240–600-volt neon indicating lamps. OUTGOING FEEDER:Two 125 Amp MCCB with enclosure and having breaking capacity 36 KA at 415 V. The MCCB should shall be three pole and having adjustable thermal & magnetic setting & shall be of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. • Three air insulated copper bus bar of suitable Amps • One 0- 250 Amp 96 mm sq flush type pattern industrial types CT operated digital ampere meter to register the phase current. • One 0-500 Volts voltmeter 96 mm sq flash arrestor pattern industrial types CT operated digital meter to register the phase voltage • One hour meter to register the individual working of each pumping unit capable to register 10000 working hours. • Three no 240–500-volt neon indicating lamps. AUXILLIARY FEEDER: One 63 Amp MCCB with enclosure and having breaking capacity 36 KA at 415 V. The MCCB should shall be four pole and having adjustable thermal & magnetic setting & shall be of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. • Four air insulated copper bus bar of suitable Amp • One 0- 200 Amp 96 mm sq flash arrestor pattern industrial types CT operated digital ampere meter to register the phase current. • 0-200Volts voltmeter 96 mm sq flash arrestor pattern industrial types CT operated digital meter to register the phase voltage. • Three no 240–500-volt neon indicating lamp.Note: The job also includes the charge of proper earthing with G.I strip to Main control panel at site.Control Panel should be fully inbuilt with all devices for smooth operation of 2 No. pumping unit. |
| 79 | Voltage Stabilizer Supply, Installation, Testing & Commissioning of 100 Kva capacity copper wound voltage stabilizer of below mentioned specifications: Capacity: 100 Kva Three phase Type: Manually controlled Cooling: Oil Cooled Make: Reputed make Input Voltage: 300-500 volts (phase to phase), 200-270 volts (phase to Neutral) Output Voltage: 415 volts +10 % (phase to phase) 240 volts + 10 % (phase to Neutral) Suitable for: 100 % BALANCED Application: Indoor type Phase: 3-Ph, 4 wiresFrequency: 50 HZ + 3 % Response time: Instantaneous (millisecond) Mode of operation: Manual Suitability: Suitable for all Power Factors Duty Cycle: Continuous 24 Hrs. Efficiency: 98 % at full load. Losses at No Load: As per standards Losses at Full Load: As per standardsLaminations used: Imported low Losses CRGO Laminations – M4 GradeClass of Insulation: Class-A. Greater Than 6 M ohms Break Down Strength: 500-volt AC for 1 minute (for whole unit) Transformer winding: Copper strip.Container: 2-3mm thick MS steel with enameled paint Voltage regulator: 8/6 steps with suitable amperageADDITIONAL FEATURES:1. Earth fault protection. 2. High Grade CRGO Lamination. 3. 99.9% pure copper. 4. High efficiency. INSTRUMENT ACCESSORIES:1. Main “ON” indicating lamps in each phase.2. Voltmeter with input & output sides.3. Selector switch 03 no.Transformer Oil upto required level of the stabilizer Make = Castrol , Servo, Hp conforming to IS 335The T-oil shall be filled in stabilizer at siteGENERAL ARRANGEMENTS:The container shall have cooling radiators & mounted on sliding wheels, other fittings would include as follows: Lifting Lugs, Earthing Terminals-2 nos. Oil Level indicators, Rating Plate, Name plate, draining valve at appropriate place.The Job also include painting of voltage stabilizer by way applying one coat of epoxt primer and two coats of epoxy paint (preferable make: Neurolac, Berger, Asian), All tools and tackles, skilled labour required for the completion of work shall be arranged by the firm it self. |
| 80 | Manufacturing, Providing, installation, testing at site & commissioning of 50 HP capacity Star Delta auto transformer starter. The Starter shall be of following specifications and shall compromise of equipment’s detailed below: Specifications: a. Main contractor assembly having a range of 140 A L&T/ABB/Schnider/Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. b. Delta contractor assembly having a range of 140 A L& T/ABB/SChnider Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. c. Star contractor assembly having a range of 110 A, L&T/ ABB/Schnider Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. d. Thermal overload relay of suitable capacity MN series of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. e. Motor protection relay of suitable capacity MN series of L&T/ ABB / Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. f. Double timer assembly (electro pneumatic) having a range of 0-60 second of L& T /ABB / Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. g. Single phase preventer of suitable capacity with selectable under & over voltage of L&T/ABB Equivalent make as approved in EOI of SE mechanical circle Kashmir I&FC Department Srinagar. h. Control MCB of suitable capacity amperes range. i. Electrolytic copper bus bar strips of suitable size & capacity duly tinned air insulated and mounted on suitable Bakelite insulation j. One number Digital voltmeter 0-500V & one no. Ammeter digital type along with 3 No. CT coils having range 0- 500A fitted in each bus bar.Make L&T/ABB/AE/EE make. k. ON/OFF LED push button type RED & Green color of 5A-415V, 50HZ, L&T/ABB/Equivalent make. l. Frequency Meter, C.T coils and other accessories as per requirement/Design should be included.m. Complete internal wiring of the control panel for operating equipment by using adequate capacity single core copper wire of Havells/polycab/equivalent make. The wiring shall be fitted with plastic washers for identification of each wire at various joints. n. Panel for housing of all the equipment fabricated out 14 SWG gauge sheet metal of adequate size to house all the equipment with enough space to reach out to any equipment for repair/replacement. The panel shall have hinged door at the front with proper locking arrangements. The housing shall be provided with a base frame fabricated out of ISMC & welded /bolted at the bottom. The housing shall be provided with necessary cut out spaces for fitment of meters, push buttons actuator incoming & out coming connections. The panel shall be free standing, floor mounted, totally enclosed, vermin proof, spray enamel panted in two coats of conventional shade over a coat of red oxide primer both externally & internally. The panel shall have air vents for proper ventilation. Auto Transformer coil shall be made out of 1st class electrolytic copper strips having suitable capacity for the above starter. The coil shall be provided with F class insulation tape.The coil shall have tapings taken out at 50%, 65% and 80% The Core of the auto transformer shall be fabricated out of 1st class silicon 90 grade pota sheets cut to size and then tightening of the same adequately. The auto-transformer tank shall be fabricated out of MS sheet of suitable thinness to make the tank leak proof. which shall have a lid at the top provided with holes for tightening the same of the tank. The tank shall have to be painted in two coats of red oxide primer. The job includes providing and fitting of high-grade low viscosity transformer oil of reputed make up to the required level in the tank so that the auto-transformer coils get fully immersed. Adequate capacity electrolytic copper bus strips or cables shall be fitted for internal connections. The tank shall have to be fitted at back side of the starter |
| 81 | RUBBER MATS: Providing &laying of checkered shock proof rubber mating of IS mark of reputed make. The electrical mats are used as floor covering in areas of high voltage applications for the safety of the workers generally caused due to leakage of electric current. Construction: Insulating mats made from highly electrical resistant elastomer, free from any insertions. Surface: upper surface is having small anti-skid aberration marks to avoid slippery effects and lower is plain. Usage: The rubber mats can be placed in front of HT/LT electrical control panel, voltage stabilizer, starters, motors, bus bars for safety of workers. Specifications: Size: 1M Width X 2Mtr Length Colour: Black Thickness: 19mm |
| 82 | Electrification of Pump House: |
| 83 | Providing and fitting of 1.5 sq. mm PVC insulated Copper wire of (Havells/anchor/ Polycab make) |
| 84 | Providing and fitting of PVC channel 1\\" size along with bend connections and other supports, square blocks, etc. |
| 85 | Providing and fitting of angle holders with ceiling rose. |
| 86 | Providing and fitting of 5 W LED bulbs (Havells/Eveready/syska or any other reputed make) |
| 87 | Providing , Fitting, Testing and Commissioning of 50 watt LED flood lights of Following Secifications.Specification:Type: LED flood lightMake: Havells/Crompton/Philips/BajajRated Power: 50 watt.Mounting : WallIP Rating : IP65/66Body Material : AluminiumUsage/Application : Outdoor |
| 88 | Providing and fitting of Switches (Anchors/SSK)06 A rating |
| 89 | Providing and fitting of lighting indicator (Anchor/ SSK) -06A rating |
| 90 | Providing and fitting of fan regulator with rotary step (SSK/Anchor) |
| 91 | Providing and fitting of 6A-2/3 pin-universal socket, 240V, 50 Hz, AC. |
| 92 | Enclosing box for switches (Topsun/ Anchor) |
| 93 | Providing and fitting of 2.5 sq. mm PVC insulated Copper wire (Havells/anchor/ Polycab/Finolex make) |
| 94 | Providing and fittingof SS combine box type at specified heating points. (Anchor/ SSK) |
| 95 | Providing and fitting MCB 6A SP (Havells/IndoAsian/ Anchor) for lighting circuits |
| 96 | Providing and fitting MCB 20A DP (Havells/IndoAsian/Ancor) for heating circuit |
| 97 | Providing and fitting of 12-way MCB end boxBenlo/ Anchor/ Havells/ SSK/ HPL) |
| 98 | Providing,fitting and testing of ceiling fan \\"Orpat/Orient/bajaj\\" make having sveep of 1200mn (48\\"). working on 230V, 50Hz, 16A.C. |
| 99 | Providing of korean blanket of ultra-soft and cozy double type for workers deputed at site having weight 8 kg |
| 100 | Providing of rechargeable 10W LED torch of Havells make for workers deputed at site |
| 101 | Fire extinguishers (ABC type) 06 kg capacity as per IS 15683 |
| 102 | Safety gadgets including helmets, gloves, shock proof shoes, etc. |
| 103 | GI strip for earthing:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysSep 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender