Tender For Bid No. Dm/Ms/Cpm-Gz/318: Various Enabling Works, Development Works, Commuter Amenities, Security Related Works And Other Miscellaneous Works For The Delhi-Meerut Namo Bharat Corridor.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
30 Sep 2026
22 days left
EMD
19.77 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Bid No. Dm/Ms/Cpm-Gz/318: Various Enabling Works, Development Works, Commuter Amenities, Security Related Works And Other Miscellaneous Works For The Delhi-Meerut Namo Bharat Corridor.
BOQ
| Sl. No. | Item Description |
| 1 | NATIONAL CAPITAL REGION TRANSPORT CORPORATION LTD. Bid No. DM/MS/CPM-GZ/318: Various Enabling works, development works, commuter amenities, security related works and other miscellaneous works for the Delhi-Meerut Namo Bharat Corridor. Price Bid NATIONAL CAPITAL REGION TRANSPORT CORPORATION LTD Gatishakti Bhawan INA, New Delhi –110 023 Preamble Name of Work: Bid No. DM/MS/CPM-GZ/318: Various Enabling works, development works, commuter amenities, security related works and other miscellaneous works for the Delhi-Meerut Namo Bharat Corridor. S.No. Description |
| 2 | The Price bid shall be read in conjunction with the Bidding Documents. |
| 3 | There are Two Schedules in the Financial Bid as follows : (i) Schedule - A (DSR/Civil-2023, DSR/E&M-2025, DSR/Horticulture-2025 Items)(ii) Schedule - B (Non DSR Items)The bidder is required to quote a flat percentage \\"Excess\\" (+) / \\"Less\\" (-) / \\"At par\\" with respect to the amount of the Schedules in the \\"BoQ1\\" Sheet and further discount if any may be Quoted in the \\"BOQ2\\" Sheet along with methodology of discount if any. The percentage quoted by the Bidder in \\"BoQ1\\" sheet and discount (if any) quoted by the Bidder in the \\"BoQ2\\" will be applied on the individual rate for the respective schedules for the purpose of payment to the Contractor. |
| 4 | The quantities for various items provided in the Price Bid are estimated quantities and are given to provide a common basis for Bidding. During the execution of works, the same may vary based upon \\"Good for Construction\\" (GFC) drawings approved by the Engineer and as per the site conditions. The basis of the payment will be the actual quantities of the work executed and accepted by the Engineer or quantities as per the GFC drawings whichever is less and shall be paid / valued as per the accepted rates. |
| 5 | The quoted rates for various items are for completed and finished items of work complete in all respects. It will be deemed to include all the cost involved in the execution of the items and shall include all duties, taxes [except Goods and Service Tax (GST) and Custom Duty] royalties, cess, overheads, profit and other levies payable by the Bidder under the Contract, or for any other cause etc. The Bidder shall be required to consider this aspect while quoting rates. It shall include all general risks, liabilities and obligations set out or implied in the Contract shall and including remedy of any defects during the Defect Liability Period, unless otherwise provided in the Contract. The whole cost of complying with the provisions of the Contract shall be deemed to have been included in the quoted rates. GST as prevalent will be paid extra. |
| 6 | Bidder may please note that to perform this contract nothing extra shall be payable on account of field constraints, non-availability of uninterrupted front, cost of project management, monitoring, coordination and supervision, cost of adhering to quality requirements (QA/QC), cost of adhering to SHE requirements, cost of preparing drawings and documents, as-built records and documentation, preparation of detailed scheme for taking necessary clearance and approval from the concerned authority and other local bodies etc. |
| 7 | Income Tax and any other statutory taxes to be deducted at source will be deducted by the Employer from the due payments of the contractor in accordance with the prevailing rules in force. |
| 8 | Bidder should not tamper the Price Bid. If the Price Bid is found to be modified by the bidder, then the same will be treated as incomplete and non-responsive and may result in the rejection of the Bid. |
| 9 | Method of Quoting the Price in the Price Bid:The Price Bid is in Excel Format and the Quoting the Price in the Price Bid should be as Follows: (i) Whole Excel Worksheet is Locked except the Cells which are highlighted in Blue. (ii) Bidders are required to fill these cells which are highlighted in Blue only. (iii) Bidder is required to quote a flat percentage Excess/Less/At par on 'Individual Amount for EACH SCHEDULE SEPARATELY' in \\"BOQ1'' Sheet of Price Bid and further discount if any in BOQ2 of Price Bid along with methodolodgy of discount if any. (iv) All 'blanks' in the Pricing Document, where the Bidder is permitted to quote shall be filled in. (v) If some % is quoted inspite of marking 'At par' that % will not be considered and it will be taken as \\"At par\\" on basic amount. Failure to quote the % in case of excess or less for the \\"Total amount of Schedule\\" shall be treated as \\"At Par\\" and shall be evaluated accordingly. (vi) Bidder is required to quote Rates in INR only. |
| 10 | Errors will be corrected by the Employer for any arithmetic errors in computation or summation as per contract conditions. |
| 11 | For Calculation of rates (excluding GST) of DSR 2023 Civil & Civil finishing items, following Methodology issued by CPWD vide Office Memorendum (OM) dated 08.08.2024 have been adopted:As per CPWD OM the rates of individual items of DSR 2023 has been multiplied with correction factor on account of GST @ 0.973 to the existing rate of DSR 2023 item in order to achieve modified DSR rate and then reduced the corrected rate by 18% for making DSR item excluding GST.Note:The above Methodology shall be applicable for calculating the rate of Individual Items of DSR 2023 in Schedule A.Based on the above Methodology and price quoted by the bidder payment shall be made for the individual items executed under Lump Sum amount of DSR 2023 in Schedule A. For Calculation of rates of Schedule - A (DSR/E&M-2025, DSR/Horticulture-2025 Items) (excluding GST), reduced the rate by applicable GST% for the item for making DSR item excluding GST. Note:The above Methodology shall be applicable for calculating the rate of Individual Items of Schedule A (to be executed under Lump Sum amount). NOTE FOR THE BIDDERS: |
| 12 | BIDDERS TO NOTE THAT THE WORK MAY BE REQUIRED TO BE CARRIED OUT IN LIMITED HOURS DURING NON OPERATIONAL HOURS IN THE STATION PREMISES/VIADUCT/ TUNNEL AS PER DIRECTIONS OF ENGINEER IN CHARGE AND NOTHING EXTRA SHALL BE PAYABLE ON THIS ACCOUNT. BIDDERS TO CAREFULLY REFER CLAUSE 2.1.1 OF 'SCOPE OF WORK', EMPLOYERS' REQUIREMENTS (6A) FOR DETAILS. |
| 13 | BIDDERS TO NOTE THAT THE WORK SHALL BE CARRIED OUT AS PER THE 'TASK ORDERS' ISSUED FOR DIFFERENT WORKS BY ENGINEER IN CHARGE. THE CONTRACTOR SHALL BE REQUIRED TO CARRY OUT THE WORK WITHIN THE TIME STIPULATED IN THE TASK ORDER. BIDDERS TO CAREFULLY REFER CLAUSE 2.1.3 OF 'SCOPE OF WORK', EMPLOYERS' REQUIREMENTS (6A) FOR DETAILS. |
| 14 | SCHEDULE-A |
| 15 | SCHEDULE-B Letter of Price Bid Bid No.: DM/MS/CPM-GZ/318 To National Capital Region Transport Corportation Limited GatiShakti Bhawan,INA, New Delhi- 110023 We, the undersigned, declare that: (a) We have examined and have no reservations to the Bidding Documents, including Addenda issued in accordance with Instructions to Bidders (ITB) 8. (b) We offer to execute in conformity with the Bidding Documents and the Technical Bid submitted for the following Works: Name of Work: DM/MS/CPM-GZ/318: Various Enabling works, development works, commuter amenities, security related works and other miscellaneous works for the Delhi-Meerut Namo Bharat Corridor. miscellaneous works incl. road works. (c) The total price of our Bid, below is: [amount in INR in figures] 0.0 (g) If our Bid is accepted, we commit to obtain a performance security in accordance with the Bidding Documents. (h) We understand that this bid, together with your written acceptance thereof included in your notification of award, shall constitute a binding contract between us, until a formal contract is prepared and executed. (i) We understand that you are not bound to accept the lowest evaluated bid or any other bid that you may receive. Name of the authorized representative of the bidder Desiganation of the authorized representative Name of the Bidder/ Bidding Firm / Company : 0.0 Date: (DD/MM/YYYY) ESTIMATE Name of Work: Various enabling works, development works, commuter amenities, security related works and other miscellaneous works for the Delhi - Ghaziabad - Meerut Namo Bharat Corridor. S. No. DSR 2023Item No. Description of Item Unit Rate(incl. GST @ 18%) Corrected Rate(incl. GST @ 18%) Rate(excl. GST @ 18%) Quantity Amount(excl. GST @ 18%) Remarks (1) (2) (3) (4) (5) (6) (7) (8) (9) [Col.7 x Col. 8] (10) Schedule - A (DSR-2023 Items for Civil works) 1.0 CARRIAGE OF MATERIAL |
| 16 | 1.1 a 1.1.2 Earth - up to 1 km cum 217.55 211.68 179.39 100.0 17939.0 104.4037 Total of Carriage of Material 17939.0 2.0 EARTH WORK |
| 17 | 2.6 a 2.6.1 All kinds of soil cum 177.5 172.71 146.36 500.0 73180.0 |
| 18 | 2.8 a 2.8.1 All kinds of soil. cum 260.3 253.27 214.64 75.0 16098.0 |
| 19 | 2.1 - 2.10.1 All kinds of soil a 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia metre 352.15 342.64 290.37 75.0 21777.75 |
| 20 | 2.26 a 2.26.1 All kinds of soil cum 126.8 123.38 104.56 100.0 10456.0 |
| 21 | 2.3 a 2.30.1 All kinds of soil each 82.45 80.22 67.98 250.0 16997.5 Total of Earth Work 434843.25 4.0 CONCRETE WORK |
| 22 | 4.1 a 4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) cum 7878.5 7665.78 6496.42 100.0 649642.0 b 4.1.5 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) cum 7294.7 7097.74 6015.03 35.0 210526.4 |
| 23 | 4.2 a 4.2.2 1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). cum 10357.55 10077.9 8540.59 35.0 298920.65 b 4.2.3 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) cum 9895.2 9628.03 8159.35 35.0 285577.25 |
| 24 | 4.2 - 4.20.1 All works upto plinth level : a 4.20.1.2 Concrete of M15 grade with minimum cement content of 240 kg /cum cum 8986.15 8743.52 7409.76 20.0 148195.4 Total of Concrete Work 1592861.7 5.0 REINFORCED CEMENT CONCRETE |
| 25 | 5.9 a 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 392.15 381.56 323.36 200.0 64672.0 b 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. sqm 842.5 819.75 694.7 150.0 104206.5 c 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 927.25 902.21 764.58 150.0 114688.5 d 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 736.4 716.52 607.22 150.0 91083.0 e 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 961.3 935.34 792.66 100.0 79267.0 f 5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 764.95 744.3 630.76 40.0 25230.4 - 5.9.16 Edges of slabs and breaks in floors and walls g 5.9.16.1 Under 20 cm wide metre 208.55 202.92 171.97 40.0 6878.8 |
| 26 | 5.11 a 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) sqm 384.3 373.92 316.88 100.0 31688.0 |
| 27 | 5.22 a 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 107.85 104.94 88.93 2000.0 177860.0 |
| 28 | 5.22A a 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 107.85 104.94 88.93 3000.0 266790.0 |
| 29 | 5.33 - 5.33.1 All works upto plinth level a 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 9504.75 9248.12 7837.39 20.0 156747.8 - 5.33.2 All works above plinth level upto floor V level b 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 9860.4 9594.17 8130.65 20.0 162613.0 |
| 30 | 5.35 Total of Reinforced Cement Concrete Work 1372449.5 6.0 MASONRY WORK |
| 31 | 6.1 a 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 7132.25 6939.68 5881.08 100.0 588108.0 |
| 32 | 6.15 Total of Masonry Work 605392.0 7.0 STONE WORK |
| 33 | 7.8 a 7.8.1 Masonry work (first sort), in cement mortar 1:6 (1 cement : 6 coarse sand) cum 10741.6 10451.58 8857.27 50.0 442863.5 Total of Stone Work 442863.5 8.0 CLADDING WORK |
| 34 | 8.2 - 8.2.2 Granite stone slab of colour black, Cherry/Ruby red a 8.2.2.2 Area of slab over 0.50 sqm sqm 5136.3 4997.62 4235.27 38.0 160940.26 |
| 35 | 8.3 a 8.3.2 Granite work metre 510.95 497.15 421.31 130.0 54771.6 |
| 36 | 8.2 a 8.20.1 Red sand stone - 30mm thick gang saw cut stone sqm 2902.65 2824.28 2393.46 100.0 239346.0 |
| 37 | 8.31 Total of Cladding Work 695957.21 10.0 STEEL WORK |
| 38 | 10.16 a 10.16.1 Hot finished welded type tubes kg 194.4 189.15 160.3 1100.0 176330.0 |
| 39 | 10.25 a 10.25.1 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete kg 123.6 120.26 101.92 500.0 50960.0 b 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 172.6 167.94 142.32 100.0 14232.0 |
| 40 | 10.28 Total of Steel Work 982557.0 11.0 FLOORING |
| 41 | 11.3 a 11.30.1 Red sand stone sqm 1647.0 1602.53 1358.08 250.0 339520.0 |
| 42 | 11.41 a 11.41.2 Size of Tile 600x600 mm sqm 1553.46 1511.52 1280.95 300.0 384285.0 |
| 43 | 11.41A - 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size a 11.41A.3.1 Size of Tile 600 x 600 mm sqm 1464.85 1425.3 1207.88 150.0 181182.0 |
| 44 | 11.46 a 11.46.2 Size of Tile 600x600 mm sqm 1623.05 1579.23 1338.33 100.0 133833.0 |
| 45 | 11.48 a 11.48.2 Size of Tile 600x600 mm sqm 309.05 300.71 254.84 500.0 127420.0 |
| 46 | 11.54 - - (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. - - (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. - - (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. a 11.54.2 450 mm Finished Floor Height (FFH). sqm 5977.35 5815.96 4928.78 35.0 172507.3 Total of Flooring Work 1338747.3 12.0 ROOFING |
| 47 | 12.45 a 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) sqm 1355.8 1319.19 1117.96 200.0 223592.0 |
| 48 | 12.54 a 12.54.2 GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation. sqm 2354.65 2291.07 1941.58 200.0 388318.0 Total of Roofing Work 611910.0 13.0 FINISHING |
| 49 | 13.4 a 13.4.2 1:6 (1 cement: 6 coarse sand) sqm 343.65 334.37 283.36 500.0 141685.0 |
| 50 | 13.5 a 13.5.2 1:6 (1 cement: 6 coarse sand) sqm 395.35 384.68 326.0 500.0 163000.0 |
| 51 | 13.11 |
| 52 | 13.41 a 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre sqm 185.65 180.64 153.08 200.0 30616.0 |
| 53 | 13.45 a 13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm sqm 223.6 217.56 184.37 3000.0 553140.0 |
| 54 | 13.52 a 13.52.1 On steel work sqm 241.75 235.22 199.34 3000.0 598020.0 b 13.52.2 On concrete work sqm 235.15 228.8 193.9 1000.0 193900.0 |
| 55 | 13.63 a 13.63.1 Two or more coats on new work sqm 146.8 142.84 121.05 3000.0 363150.0 |
| 56 | 13.65 a 13.65.1 Two or more coats on new work sqm 140.25 136.46 115.64 1000.0 115650.0 |
| 57 | 13.81 a 13.81.1 Old work (one or more coats) sqm 62.7 61.01 51.7 10000.0 517000.0 |
| 58 | 13.99 a 13.99.1 One or more coats on old work sqm 102.8 100.02 84.76 10000.0 847700.0 |
| 59 | 13.1 a 13.100.1 One or more coats on old work sqm 96.0 93.41 79.16 15000.0 1187400.0 |
| 60 | 13.11 a 13.110.1 Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm. sqm 169.2 164.63 139.52 10000.0 1395200.0 Total of Finishing 6384997.0 14.0 REPAIRS TO BUILDING |
| 61 | 14.1 a 14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) sqm 560.5 545.37 462.18 1500.0 693270.0 |
| 62 | 14.23 |
| 63 | 14.72 - - Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. Total of Repairs to Building 816421.0 15.0 DISMANTLING AND DEMOLISHING |
| 64 | 15.2 a 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) cum 2434.25 2368.53 2007.23 30.0 60216.6 Total of Dismentling and Demolishing 60216.6 16.0 ROAD WORK |
| 65 | 16.18 a 16.18.1 With G.I. barbed wire metre 22.1 21.5 18.22 10000.0 182200.0 |
| 66 | 16.3 a 16.30.1 On W.B.M. @ 0.75 Kg / sqm sqm 60.5 58.87 49.89 1000.0 49890.0 b 16.30.2 On bituminous surface @ 0.50 Kg / sqm sqm 48.2 46.9 39.75 3000.0 119220.0 |
| 67 | 16.48 a 16.48.1 New work (Two or more coats) sqm 288.9 281.1 238.22 2000.0 476440.0 b 16.48.2 Old work (One or more coats) sqm 189.85 184.72 156.54 4000.0 626200.0 |
| 68 | 16.53 |
| 69 | 16.54 a 16.54.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. cum 11129.55 10829.05 9177.16 50.0 458858.0 b 16.54.2 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity. cum 11032.2 10734.33 9096.89 50.0 454844.5 |
| 70 | 16.55 a 16.55.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.50% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. cum 8505.65 8276.0 7013.56 50.0 350678.0 |
| 71 | 16.57 a 16.57.1 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. cum 12126.2 11798.79 9998.97 50.0 499949.0 |
| 72 | 16.62 |
| 73 | 16.68 |
| 74 | 16.69 |
| 75 | 16.78 a 16.78.1 With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 cum 2784.0 2708.83 2295.62 150.0 344343.0 |
| 76 | 16.79 |
| 77 | 16.91 a 16.91.1 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. sqm 1045.65 1017.42 862.22 250.0 215555.0 |
| 78 | 16.93 Total of Road Work 7446223.6 MISCELLANEOUS DSR ITEMS |
| 79 | - Total of DSR 2023 Civil Items = 27803378.66 |
| 80 | Total of Schedule - A = 30803378.66 Name of Work: Bid No. DM/MS/CPM-GZ/318: Various Enabling works, development works, commuter amenities, security related works and other miscellaneous works for the Delhi-Meerut Namo Bharat Corridor. Schedule - B (NDSR Items) NDSR Item No. Description of Item Unit Rate (excl. GST) Quantity Amount(excl. GST) Remark (2) (3) (4) (5) (6) (7) [Col.5 x Col. 6] (8) |
| 81 | Providing fixing and jointing UV stabilized SWR(Type-A) pipes conforming to IS:13592 at Pier cap/Porta for drainage of Rain Water including all fitting such as bends, clamps, tees, cow , clean out plugs, offsets, Y-Tees, tees, door fitting, clips clamps stays etc. Conforming to I:14735, including jointing with rubber gasket fixing in sunk areas, fixing at all /ceiling level supported by steel camps & hangers etc., including Cutting, chases/holes in floors /wal /slab and making good the same after pipe have been duly laid and testing complete in all respects. |
| 82 | Shear Keys & Segments making gaps by breaking and/or chipping the shear key and finishing the same with the approved structural binding materia .The item includes providing the Manlifter, Impact Protection Vehicle, all Safety precautions, Hilti breaker and providing the structutal binding materia of FOSROC or BASF or any other equivalent make for the repairing of concrete etc as per the direction of Engineer-in-charge. |
| 83 | Providing, fixing and jointing of GI Spout in Segments/Deck Slabs for drainage work |
| 84 | Cleaning of Vertical Drainage Pipe inside Pier in Viaduct by Core Cutting and other means.(1)The item includes fixing of Core Cutting Machine over Pier Cap for Core cutting in Central drain Pipe & shifting of core cutting Machine from one Pier to another Pier by suitable means.(2) Use of Chain pulley for handling movement of Diamond core cutter which is fixed on a long and heavy pipe as per site requirement. (3) 50 mm dia core cutting on initial stage. (4) After 50 mm core cutting, it follows 100 mm dia and then 150 mm dia core cutting in Central Pipe.(5) Cleaning of horizontal Pipe of Central Drain (by core cutting & other suitable means). All works include the night charges, wastage of labours due to less working hours, block hours, shifting of labours, machines, generator, fuel, maintenance and mobilisiation and demobilisation of machinery etc. from one location to another location. The work should be executed as per the directions of Engineer-in-Charge. The rate shall comprise all taxes and contractor profit, etc. |
| 85 | Making of cutout(Core Cutting) of 100mm Dia, upto 200 mm long in all grades of RCC structures for various services |
| 86 | Making of cutout(Core Cutting) of 150-200 mm Dia, upto 350 mm long in all grades of RCC structures for various services |
| 87 | Grinding & Finishing of the concrete/RCC Surface to make them even for putty and other finishing work in soffits of slabs at RRTS stations |
| 88 | Providing and laying 30mm thick mirror polished Sadarhalli Grey/ Jhalore Beige granite stone work of upto and including sizes of 1200mmX600mm of approved colour/ pattern with 4mm groove all around at all leve for wall linings/ columns/ skirtings (veneer work) by mechanical arrangement with SS cramps/ brackets, anchor bolts, 6 mm vertical SS pins of approved make and inserts as per drawings and specifications. The cost of making necessary grooves all around stone pieces, chamfering of corner edges and polishing are included. |
| 89 | Providing & Fixing Polished Granite Coping of Jet Black or any other dark granite stone, bull-nosed over 20 mm thick cement mortar 1:4(1 cement: 4coarse sand) with joint treated with white cement mixed with matching pigment including Rubbing, Curing , Moulding & polishing to edge to give high gloss finish etc., complete. |
| 90 | 30 mm thick |
| 91 | Providing and laying 30mm thick prepolished Sadarahlli grey/cheema pink/Jhalore beige granite slab of sizes upto and inclusing 1200 x 600 on floor using 5mm thick approved thick bed adhesive as per specification over prepared base on 20mm (average) thick base of cement mortar 1:4 using 43 grade cement, water reducing admixture as per ISO 9103:1999 and jointing with white cement with matching colour pigment all complete (color of granite as approved by engineer) in levelling course laid to proper slopes over screed base including base preparattion, movement joint in screed as per specification with 10mm thick compressible filter to edge of screed/blockwork jucntion with two parts polysulphide sealant to top edge,drainage gullies as per approved section, curing,testing etc. all complete as per speciifcations and relevant drawings. Screed shall be measured and paid extra as per DSR 2023 item no. 4.20.2.1. |
| 92 | Extra for red/raw silk/jet black/tan brown/kashmir yellow/ikon brown/multi red/blue pearl granite |
| 93 | Providing and operating Diesel Boom Lifter for 25-28 Meter height for working at height below soffit of viaduct and stations. Rate shall be include diesel charges and operator with all safety precautions complete and mobilisation and demobilisation and movement of man lifter at site. |
| 94 | Providing, Supply, fixing & installation of Toughened Laminated glass cladding/Panel in station lifts at Stations. System designed to withstand the wind pressure as per requirement. The suspended system held with spider fitting of SS-316 steel of approved manufacturer with glass panel having 13.52 mm (6+1.52+6) laminated glass of approved make or as directed by the Engineer-in-Charge held together with SS-316 grade stainless steel four arm spider, three arm spider, two arm spider, single arm spider of Dorma or equivalent approved make including route and fixed bolt for glass, supported on steel structure with adjustable adaptor bush to make level in glass for lateral support as per design. The joints b/w glass pane (6 to 8 mm) and gaps at the perimeter & in u- channel of the assembly to be filled with sealant of approved make. |
| 95 | Providing, Fixing and Installation of Lacquered Glass Cladding at Stations. The item includes all necessary arrangements for fixing i.e., plyboard, sealant etc. |
| 96 | W.C pan with ISI marked white solid plastic seat and lid. |
| 97 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting,of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etccomplete. |
| 98 | Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the wal and floors wherever required: |
| 99 | White vitreous china Orissa pattern W.C. pan of size 580 x 440 mm. with integral type foot rests. |
| 100 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the wal and floors wherever required |
| 101 | Range of two urinal basins with 5 litre white P.V.C.automatic flushing cistern |
| 102 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
| 103 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. Brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wal wherever require: |
| 104 | White Vitreous china Wash basin of size 630 x 450mm with a pair of 15mm C.P brass pillar taps. |
| 105 | White Vitreous china Flat Back Wash basin of size 550 x 400mm with single 15mm C.P brass pillar taps. |
| 106 | Providing and fixing toilet paper holder. |
| 107 | CP Brass |
| 108 | Providing & Fixing in position precast RCC bollards of size 950mm (Height) 150mm dia. vibro compacted accurately designed moulds appropriate reinforced with drawing plastic spacer & concrete grade M25 as per approved design and drawing. The bollards shall be fixed in cement concrete block of mix 1:2:4 and pit size of 30x30x30 cm including earthwork excavation etc. complete as per direction and instruction of Engineer in charge |
| 109 | Providing laying of Granular Texture paint of required make of approved vendor consisting of all coats all complete as per specification and direction of engineer in charge and incl. the expenses of excess provision by manliftapproved vendor. |
| 110 | Supplying and installing SS perforated trash pedal bin of capacity 35 ltr in station building a various locations and levels |
| 111 | Supply and installing of steel pole rounded dustbin with cap of capacity 60 ltr in stations building at various locations and leve |
| 112 | Extra for Finishing the top concrete surface of flooring laid under above item by providing vacuum dewatering system ”Trimix” including finishing the top using power trowe to a smooth and fair surface. |
| 113 | Cutting of grooves on concrete /surface within 4 days after completion of laying of concrete as above using a power driven cutting machine and filling the grooves with piolysulphide sealant as approved all complete and as directed. The width & depth of the groove shall be 5mm & 30 mm respectively |
| 114 | Providing and laying PCC/RCC for flooring on prepared sub grade with/without reinfrcement as directed, the rares quoted shall be inclusive of lateral formwork.the floor shall be cast in alternate strips and the concrete shall be vibrated and finished smooth by power trowelling and finished as specified and as directed.Required level or slope shall be maintained on the top surface, Care shall be taken to prevent local depressions. Only steel sections such as channe , angles will be allowed to be used as form work.The top level of form work shall be flushed with required finished floor level.Under any circumstances form work shall not be allowed to project above FFL.(Reinforcement/Steel wire mesh if ordered will be paid separately under respective items).Concrete of M25 grade with minimum qty. of cement. 360kgs/cum. |
| 115 | Providing and laying 30mm thick prepolished with 25%-35% quantity flamed as per pattern Granite Stone flooring in treads and landings (including bull nosing, rounding the nose and making groove) of steps of approved colour, size and pattern, (sample of granite stone shall be approved by Engineer-in-charge) over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coresand) laid and jointed with neat cement slurry mixed with pigment to match the shade of granite stone complete as per specifications and architectural drawings. |
| 116 | Extra for Jet Black, Icone Brown, Lakha red or Red Silk, Blue Pearl granite |
| 117 | Providing and laying 20 mm thick mirror polished Granite Stone in Risers/skirting of steps of approved colour, size and pattern, (sample of granite stone shall be approved by Engineer-in-charge) over 12 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of granite stone complete as per specifications and relevant drawings. |
| 118 | Extra for Jet Black, tan Brown,red or Red Silk or any other color granite |
| 119 | Vitrified Flooring: Providing and laying matte finish vitrified tile of 1st quality in all colors as per control sample at all leve in public & back-of house areas and toilet floor and skirting over 20mm thick bed of cement mortar1:4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigments all complete as per relevant drawings and specifications laid over screed/foam concrete as per relevant architectural drawings. Rates include coordination for cutouts, holes and finishing of the same. |
| 120 | Size of tile 600x600x10 ( for toilets) |
| 121 | Providing and fixing 1st quality Vitrified wall tiles of approved make, shade, colour and finish in all colours, shades, size in skirting, wall cladding, border tiles and dados over 20/12 mm thick bed of cement mortar 1:4 (1 cement : 3 coarse sand) and jointing with approved grouting material with pointing in white cement mixed with pigment of machine shade complete. |
| 122 | Providing and installing counters of MS (with primer and 2 coats of enamel paint) carcass in TOM, EFO etc with 30mm polished & moulded Jet Black Granite top with all cutouts/ openings including providing and fixing over 19mm thick commercial board & 19 x 3 mm teak wood lipping all complete of approved quality as per specifications and approved drawings (Plan area shall be considered for measurement) |
| 123 | Granite Flooring: Providing and fixing flamed finish Sadarahalli grey granite stone (bull nosed) of size 1200x600x60mm at platform edge level using 5mm thick approved thick bed adhesive as per specification over prepared base on 20mm ( average) thick base of cement mortar in1:4(1cement:4total aggregate-sand and 10mm single sized aggregate) using 43 grade cement, water reducing admixture as per ISO 9103:1999 and jointing with white cement with matching colour pigment all complete in levelling course laid to proper slopes over screed base including, base preparation including movement joint in screed as per specification with 10mm thick compressible filler to edge of screed with two parts polysulphide sealant to top edge as per approved drawing and directions of engineer-in-charge. |
| 124 | Extra for Honed finish |
| 125 | Providing and laying Honed Granite stone in required design and patterns complete as per the architectural drawings with 30mm thick stone slab over notched drain channel cover. all complete as specified and as directed by the Engineer-in-Charge : |
| 126 | Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 18 mm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. |
| 127 | Granite Stone of approved shade |
| 128 | Providing and laying Foam Concrete of Versatile low density free flowing, self levelling and self compacting under raised floor as having density 1200 kg/m3. The concrete shall be laid in proper slope to maintain the required level to receive the specified flooring as mentioned in the relevant architectural drawings. The rate shall include cleaning, levelling to maintain in proper slope as per specification, appoved architectural drawing and as directed by Engineer-in-charge. Note: The rates includes all necessary Materia , Labour, Too and plant, equipments etc. Nothing shall be paid extra on this items. |
| 129 | 30mm thick Honed finish granite on treads - Providing and fixing 30mm thick Honed Granite Stone on Staircase treads and landings including bull nosing, (rounding the nose and making groove intread) of steps not exceeding 32 cm in width of any approved colour and shade (Jeerawal white/ P white etc or any), size and pattern, (sample of granite stone shall be approved by Engineer-in-chrage) backing filled with chemical adhesive of approved make (BAL Endura / Duo-Bond / Laticrete / Bafer of Diamond rated / Star) complete as per specifications and relevant architectural drawings. There should be minimum gap between stones, and the gap should be grouted with higher polymer epoxy grout of make (BAL Endura / Duo-Bond / Laticrete / Bafer - mappal of diamond rated / Star),. The Rates include all materia (Granite Stone, Chemical Adhesive, Epoxy grout and all necessary materia required to complete the job), labour, too , paint and equipments. Nothing shall be paid extra |
| 130 | Providing and fixing in expansion joints of beams/columns/slab SILFIL (Armour Board) expanded Polythelene expansion joint filler material (manufactured by M/s. Supreme Industries Ltd., New Delhi or other approved manufacturer as per Engineer in Charge) of specified thickness - 50 mm thick |
| 131 | Filling sunken areas with cinder(Density not exceeding 900 kg / cum and 12.50 mm Nominal size) cement concrete 1:15(1cinder:15cement), including watering ramming to required consolidation complete at any level. |
| 132 | Providing and fixing chicken wire mesh (26 gauge) at the junctions of RCC & brick work fixed with wire nail in cement mortar 1:4 (1 cement : 4 fine sand) etc complete. |
| 133 | Providing and filling conbextra GP-2 non-shrink grout under base plates or holes or around bolts as per direction of Engineer-in-charge |
| 134 | Providing and fixing in position stainless steel Grade SS304L glossy finish sheet 3mm thick for covering work in between escalator and staircase/ wall over a frame of SS Angle frame work of size 50 x50 x 5mm all along the escalator and staircase/ wall including all necessary harwares, fabrication, buffing, fixing , including necessary scaffolding, red oxide primer of approved make and quality to the MS Angle frame work etc. complete as per approved drawings and specifications and as directed by Engineer In Charge. |
| 135 | Providing and fixing 6mm tinted toughened float glass in aluminium door, window, ventilator shutters and partitions etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) |
| 136 | Providing and fixing of toughened laminated glass door in EFO (6mm + 1.52mm + 6mm) including stainless steel door handles, deadlock and Floorspring complete necessary cutting in granite flooring for housing of floor spring as/drawing |
| 137 | Providing & installing fixed glazed wall assembly with specified fixing & finish to Ticket Office and EFO using of 2 sheets of 6mm thick toughened glass with nominal gap silicon sealant joint. Glass shall be clear, toughened and laminated with 1.52mm thick poly vinyl butyral layer. Glass held with SS patch fittings - all complete as per relevant architectural drawings and specification with cut out & holes. |
| 138 | Providing and installing fixed glazed security wall assembly {Security Barriers (approx 2100mm high)} of stainless steel with specified fixings and finish using 2 sheets of 6mm thick toughened glass with nominal gap silicone sealant joints. Glass shall be clear, toughened and laminated with 1.52mm thick polyvinyl butyral layer- all complete as per relevant architectural drawings and specification. |
| 139 | Providing and fixing swing and folding single shutter with MS louvers steel door of required size as per approved drawings, designs, specifications and directions as per the following detai . Outer frames with 50 x 50 x 5 mm MS angle frame and 4 leaved MS shutters and each leaf is made out of 40 x 40 x 1.25 mm thick MS square section all round 40 x 4 mm MS flats louvers fabricated as per the drawings with all necessary arrangements like pivot , hinges, with ball bearing movement, handles, stoppers, tower bolts and locking arrangements etc. including applying priming coat of red lead paint cost of materia , labour , HOM of machineries complete as per specifications including fixing to the wal as approved by the Engineer. |
| 140 | Providing and fixing aluminium mill finish sub frame work with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285 fixed with raw plugs and stainless steel screws etc. |
| 141 | Providing and fixing 8mm thk High Pressure Laminate panel as per EN 438-6 type eds manufactured using specially treated acrylic resins, hardened & competed under high pressure and temperature thus providing all weather protection and light fastness with fixing of power coated substructure sqm aluminium box section of 50mm x 25mm or 7smmx25mm suitable sized with maximum fastening gap between 340mm-600mm using special stainless steel screw fastener and HPL should be fixed to aluminium channel using powder coated dome head blind rivet. |
| 142 | Aluminium metal louvers: providing and fixing Aluminum louvers of 84r sections with pvdf coating of approved colour. The system shall consist of panel 84 mm wide x 16mm deep x 0.6mm thick with round edges panel length upto 6 mtrs. The panel shall be coil coated on a continuous paint line double baked and roll formed enamelled corrosion resistance aluminium alloy aa5050 (al. Mg.) For higher strength and good roll forming characteristic. The panel shall be clipped to aluminium sl-4 panel stringer of size: 33mm wide and 86mm deep x 0.95mm thick in a standard length of 5 mtrs, made of double baked enamelled aluminium alloy aa 5050 (al. Mg.) In white colour with cutouts to hold the panel in a module of 86mm c/c. The prongs on sl–4 stringers shall be to accommodate an angle of 21.30 degrees between two pane . The first stringers shall be fixed at 150mm from both ends & thereafter at a distance of 0.75 to1 mtr, depending on wind load. The stringer shall be fixed to a suitable sub-structure with nut/bolt & washer. All properties and specifications shall comply with ecca directives and more specifically en 1396:1996 |
| 143 | Supplying, fabricating, Matt Finish, errection of required height (900 to 1100) mm high SS hand railing system. System comprising of 50mm OD Stainless Steel Grade 304, 3.15 mm thick, 25mm dia Jointing pin, SS Spider fittings, SS Base plate, pipe adjuster M16 X 200mm SS Fasteners for fixinf railing in floor/staircase by cutting hole of required dia covering with SS cover plate complete in all respect with 1 no. 12mm thick toughened glass and fixed with SS brackets and hinges and making good the flooring as per specifications and architectural drawings. |
| 144 | Fabrication, supply and erection of matte finish grade 304L SS sump covers of size 600mm X 600mm suitably supported & fixed over MS frame along with granite stone matching with relevent floor finish, lifting hooks/keys etc complete as per architectural drawing. |
| 145 | Fabrication, Supply & Installation of Stainless Steel gutters/ tray (Conforming to SS-304 L Grade) consisting of 2 mm thk sheets moulded to form tray with base width 200mm and flanges of 100mm ( total girth 400mm). The tray to be installed at the bottom of the expansion joints, anchored to the base slab with SS fasteners at regural interva all complete as per the Architectural drawings and satisfaction to the Engineer-in-charge. |
| 146 | Fabrication, supply and erection of Hot dip galvanized MS cover plate, fabricated from minimum 6 mm thick M S chequered plate fixed over cleats,stiffeners,runners using 40 X 40 X 6 mm MS angle grouted in position etc.complete as per directions of engineer-in-charge (only galvanized chequered plate is covered under this item. Other items shall be paid by weight separately. ) |
| 147 | Proma seal acrylic intumescent sealant 2 hours fire rated in accordance with BS 476-Part 20, IS 1530 Part 4 to seal gap & joint in fire rated wal and floors and around service penetration for 25 mm gap and 12 mm depth. |
| 148 | Providing and installation of ANTI SKID STRIPS 50MM WIDE with correct and final position proper line and level complete as per approved drawings, specification and direction of Engineer - Incharge. |
| 149 | GMS / GI TRENCH COVER - Fabrication, supply and erection of Hot dip galvanized MS channel cover plate, fabricated from 6mm thick MS chequered plate fixed over cleats, stiffeners, runners using 40x40x6 mm MS angle grouted in position etc complete as per directions of engineer-in-charge (only 6mm galvanized chequered plate is covered under this item. Other items shall be paid by weight separately) |
| 150 | TRAP DOOR(1200X1200)-Hingeable & sliding trap door system manufactured according to EN13964 TAIM Quality standard consisting of unit size 1200mm x 1200mm comprising 2 pane of size 600 mm x 1200mm in one unit made up of 0.6 GMS in RAL 9016 (Matt White colour) or as specified by Engineer, polyester powder coated finish and approx 95 % humidity resistance, fire performance Class A2-S1, d0. Substructure consisting of roburst hinging technology with visible U 1091 G shaped or equivalent profiles which are mounted along the width of the pane . The U 1091 G profiles or equivalent are fixed using L shaped primary carriers U 1040 or equivalent of 1.0mm thick GMS, which runs perpendicular to the U 1091 G profiles. This is suspended rigidly from the bare ceiling with M6 or equivalent threaded rods and fasteners. All components are made of galvanized steel .The rectangular pane can be swing down using spring loaded pins and hung from bolted sleeves provided on the sides. Once all the pane are swung down, they can be pushed to either side of the opening and stacked together in order to carry out any kind of work. |
| 151 | TRAP DOOR(600X600)-Hingeable & sliding trap door system manufactured according to EN13964 TAIM Quality standard consisting of unit size 600mm x 600mm made up of 0.6 GMS in RAL 9016 (Matt White colour) or as specified by Engineer, polyester powder coated finish and approx 95 % humidity resistance, fire performance Class A2-S1, d0. Substructure consisting of roburst hinging technology with visible U 1091 G shaped or equivalent profiles which are mounted along the width of the pane . The U 1091 G profiles or equivalent are fixed using L shaped primary carriers U 1040 or equivalent of 1.0mm thick GMS, which runs perpendicular to the U 1091 G profiles. This is suspended rigidly from the bare ceiling with M6 or equivalent threaded rods and fasteners. All components are made of galvanized steel .The rectangular pane can be swing down using spring loaded pins and hung from bolted sleeves provided on the sides. Once all the pane are swung down, they can be pushed to either side of the opening and stacked together in order to carry out any kind of work. |
| 152 | TRAP DOOR(450X450)-Hingeable & sliding trap door system manufactured according to EN13964 TAIM Quality standard consisting of unit size 450mm x 450mm made up of 0.6 GMS in RAL 9016 (Matt White colour) or as specified by Engineer, polyester powder coated finish and approx 95 % humidity resistance, fire performance Class A2-S1, d0. Substructure consisting of roburst hinging technology with visible U 1091 G shaped or equivalent profiles which are mounted along the width of the pane . The U 1091 G profiles or equivalent are fixed using L shaped primary carriers U 1040 or equivalent of 1.0mm thick GMS, which runs perpendicular to the U 1091 G profiles. This is suspended rigidly from the bare ceiling with M6 or equivalent threaded rods and fasteners. All components are made of galvanized steel .The rectangular pane can be swing down using spring loaded pins and hung from bolted sleeves provided on the sides. Once all the pane are swung down, they can be pushed to either side of the opening and stacked together in order to carry out any kind of work. |
| 153 | Providing and fixing 120 minutes fire rated glazing at Station Control Room. The glass shall be clear, toughened and non-wired having 120 minutes fire rating. Fire rating certification BS or equivalent shall be provided.The fire rating certification shall be composite in nature for glazing, profiles, frame, beading, etc all complete.The glazing shall be as per relevant architectural drawings and the directions of engineer-in-charge. Powder coating shade as approved by the engineer-in-charge. |
| 154 | Toilet Mirrors - Providing and fixing toilet mirror in 6 mm thick clear float glass with bevelled and polished at edge and copper coating on rear side. Fixed on wall with 6mm thick plywood and kraft paper backing fixed to wooden cleats with 8mm dia 38mm long stainless steel stud complete. |
| 155 | 5 mm thick and 30mm deep SS strips at material joint location for VDC flooring |
| 156 | Providing and installing suspended ceiling systems / vertical fascia as per controlled sample for concourse, 12mm thick Calcium Silicate Board pane with paint as per specifications including supply of suspension system of galvanised steel as per manufacturer's recommendation, top fixing of SS expanding anchor bolts, rigid hangers, accessories inclusive of providing opening for electrical fixtures / fittings, fixed framing to support fixtures / fittings and providing secondary supporting system for cable tray and duct and all complete as per relevant drawings and the direction of Engineer-in-charge. |
| 157 | BAFFLE CEILING SYSTEM: Providing and fixing 50x100 baffle ceiling ( 50mm Width & 100mm Height) system comprising of U shape pane . Baffle pane shall be made out of 0.5 mm thick electro galvanized steel material in lengths of up to 4000mm. The Coil should be stove enamelled on a continuous application for pre-treatment. The coi to go through 4 stages of pre-treatment, three times oven baked through conversion coating, priming and finish coat ensuring superior adhesion, high corrosion resistance and good colour stability. The coi to be painted on both sides after degreasing. Inside surface to have a primer of 5 microns and a coat of natural colour of 5 microns, exposed surface to have a primer of 5 microns, binder of 5 microns and topcoat of approved colour of 15 microns. Baffle Ceiling pane shall be mounted on slotted galvanized grid profile of minimum 2mm thickness in a module of 150mm. Baffle grid shall be suspended and supported by means of 6mm dia threaded suspenders at a distance of 150mm from the edge and 1200mm c/c. Baffle fixing brackets shall be used to keep the ceiling in correct place for the leveling purpose. Baffle pane shall be coil coated in a desired specification. Baffle ceiling system shall be installed in compliances with manufacturer’s technical installation brochure and manual. |
| 158 | Providing and applying two coats (maximum 8 sqm/litre per coat with minimum 125 micron wet film thickness per coat) of two-part, high build, solvent free , water emu ified epoxy resin based anti- dust concrete sealer coating on fair-faced blockwork / brickwork and concrete surfaces inclusive of surface preparation, over primer coat / initial coat as per manufacturer's recommendation- all complete as per specification. |
| 159 | Cutting chases for conduiting in wal as per direction and marking by the E & M site-in-charge to the required depth with a machine cutter & covering the same with galvanized wire mesh after installation of conduit by E & M and making ready for plastering works. |
| 160 | 20 mm water proofing cement plaster of mix 1:4 (1 cement : 4 coarse sand) in two coats for lining the drains, mixed with approved water proofing admixture for sunken areas of toilets, balconies or wherever directed by engineer in charge, including the neat cement punning over the base surface. |
| 161 | Providing and painting acrylic polyurethane enamel paint of approved brand and shade, on new work (plaster, wood or metal) two or more coats, to give an even shade, including one coat of primer, preparation of surface using automotive putty, thinners etc.surface duly emery papered to give a perfectly smooth and even prepared surface before painting etc. complete. |
| 162 | On steel work |
| 163 | On Concrete work |
| 164 | Extra for Galvanizing over structural steel as per the drawings & Specifications etc. complete in all respect. |
| 165 | Anti Carbonation paint: Providing and applying primer + two coats of 100% acrylic breathable, anti-carbonation, heat insulating,decorative external paint-sunext-8 of Sunanda or equivalent.Before giving this treatment the entire surface shall be thoroughly cleaned to remove dust,dirt,oil etc. The cracks, if any shall be filled with acrylic polymeric non shrink auto suction crack filler putty polyfill AR of Sunanda or equivalent, anti carbonation waterproof, heat insulating, decorative external paint-Sunext-8 as per manufacturer's specifications, Acrylic paint shall be spray/brush/roller applied and shall conform to the following properties:1-Carbon dioxide diffusion eqivalent air layer thickness(DIN EN 1062-6)>100m.2-Carbon dioxide diffusion resistance co-efficient (DIN EN 1062-6)>105.3-Chloride ion diffusion(ASTM C 1202)=zero panetration.4-Adhesion (ASTM D 4541_>2 N/mm2.5-Solar Reflectance Index (ASTM E 1980-11, EN 673:2011, EN 410:2011)>104. |
| 166 | Providing & Fixing Polished Granite Coping of Jet Black or any other dark granite stone, bull-nosed over 20 mm thick cement mortar 1:4(1 cement: 4coarse sand) with joint treated with white cement mixed with matching pigment including Rubbing, Curing , Moulding & polishing to edge to give high gloss finish etc. complete. |
| 167 | 30 mm thick |
| 168 | Providing & Fixing 3 mm thick tile Spacer in the joints and Grouting the joints using white cement and matching pigment mix including filling/ grouting and finishing complete as per direction of Engineer-in-charge. |
| 169 | Providing and laying of solvent-free, cast, cast in situ Epoxy Terrazzo over completely cured & levelled concrete. Fixing divider strips as per archietect's design, application pf solvent -free epoxy primer followed by approx 10mm thick solvent-free epoxy terrazzo screed of approved colour and design. Grindinh, grouting and application of acrylic sealer and polishing as per per manufacture's guidelines, complete with tool and tackles to provide durable, wear resisrtant, aesthetic flooring. |
| 170 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 171 | Providing and fixing SS handle 32mm dia X 600mm long 'H' shape fixed to glass door. |
| 172 | Providing and fixing SS Lock to glass door. |
| 173 | Providing and Installing approved silicon sealant for 75 mm width expansion joint and wherever required as per direction of Engineer-in-charge Including necessary back up all complete. |
| 174 | Providing and laying yellow visibily vitrified tile as per controlled sample of size 200x100x8 mm thick at platform level using approved thick bed adhesive over min. 65 mm thick trowel finished bonded concrete screed in 1:4 (1 cement : 4 total aggregate sand and 10 mm, single sized aggregate) using 43 grade cement water reducing admixture as per IS: 9103-1999 in levelling coarse laid to proper slope all complete as per drawing |
| 175 | Providing and laying 12 mm (minimum) thick with 3 mm- (minimum)-thick projection on surface yellow colored directional vitrified tile as per specification ) laid on floor with Laticrete 111 crete filler powder mixed with Latecrete 73 latex admix and applied to minimum thickness of 4.5 mm. The mixing ratio shall be as follow: 20 kg bag (Laticrete 111): 5.5 litre (Laticrete 73 ), Spacer of 3 mm shall be used between tile and joint filled using Laticrete latapoxy SP-IOO epoxy grout in Inca Gold colour. The joint depth shall be 6 mm. Laticrete product shall be as manufactured by Laticrete India pvt Ltd /Laticrete International Inc over 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) in levelling coarse laid to proper slope over screed base including base preparation including movement joint in screed as per specification with 10 mm thick compressible filler to edge of screed with two part of poly sulphide sealant to top edges as per approved drawing and direction of Engineer in charge. Screed shall be measured and paid extra as per DSR- 2018 item no. 4.18 |
| 176 | 300x300 hazard warning and directional tactiles as per approved drawing. |
| 177 | Supply of canter on hire charges basis for carriage DG set, pump set etc. of material, shifting of material from here and there as per requirement. For ten hours one shift shall be paid. The rate are inclusive of operator, helper and consumables etc. Nothing shall be paid extra. |
| 178 | Providing and fixing 10 mm thick poly carbonate sheet make CE or equivalent and make confirming to IS 14443:1987, of required colour, fasteners, silicon sealent, EPDM gaskets and shade including self drilling/self taping screw as per requirement. |
| 179 | Providing, supplying, erecting and fixing in position 3 mm thick poly carbonate sheet of approved color and texture. Cost to include jointing, sealing with butul adhesive and tape etc as per manufactures specification and cover all cost of labours too , plants, temporary works. etc. all complete. |
| 180 | Supply 5-7.5 HP submersible pump of discharge capacity 50-60 kL-hrs including cost of operation etc. complete. |
| 181 | Oiling and greasing of rolling shutter With H.P.equipment greasing including cleaning of oil and scrapping of grease including labours and materia during night time as per direction of Engineer-ln-Charge. For rolling shutter up to 4.5m height. |
| 182 | Reparing and maintenance of exisiting rolling shutter incl dismantaling the shutter and refixing the same and fixing of new items as per requirement including cleaning, oiling, greasing, alignment and testing complete the cost of new items will be paid separetely except small hardware like nut/bolt and nail which are included in this items. The scope of wort includes checking of Shutter for smooth funtioning quarterly or as & when required in emergency. |
| 183 | Providing and fixing Clear Vision Panel of 200mmx 300mm complete in all respect. |
| 184 | Providing and fixing Eurofile Mortice Lock- 240 with double pin cylinder having master arrangement and ss handles comlete in all respect. |
| 185 | Providing and fixing Concealed SS finish tower bolts (300mm) complete in all respect. |
| 186 | Providing and fixing SS Handles Dorma or equivalent make for double leaf door complete in all respect. |
| 187 | PVC PIPE 160mm : Providing and laying 160mm dia 6kg pressure PVC pipe for drainage all work complete as directed by Engineer-In-Charge (make- as per approved list) |
| 188 | Providing and fixing of wash basin with abulation tap and all other accessories of approved make as per direction of Engineer-In-Charge. |
| 189 | Providing and fixing Angle Valve (Make- Jaguar) Code FLR-5053N or approved equivalent as per directions of Engineer in Charge |
| 190 | Providing and fixing waste coupling (Make- Jaguar) Code ALD-705 or approved equivalent as per directions of Engineer in Charge |
| 191 | Providing and fixing Floor trap Stainless Steel jali over existing floor trap. |
| 192 | Urinal concealed cocl (CTQ_23083) or approved equivalent as per directions of Engineer in Charge |
| 193 | Hand shower (Health faucet) (ABD body) with 1meter long easy flex tube in chrome finish & wall hook model No - ALD - IVY - 585 |
| 194 | Providing and fixing of hand assembly i.e. phase fitting (made of volga Marc Parko or approved quality) of bib cock, pillar cock and angle valve by taking out of defunct badly damaged bib cock, piller cock and angle valve. |
| 195 | Providing and installing MS nipple / NRV of size of 14mm x 100mm into RCC plinth of track or any structure including the holes and sealing of openings. |
| 196 | Providing and injecting microfine injection grout panel ZL - 10 or equivalent in the RCC plinth of track or any structure under high pressure upto 30 bar as per site requirement during traffic/ non traffic hours. |
| 197 | Providing and laying of micro concrete for of small damaged patches in RCC plinth or track or structure during traffic or non traffic hours. |
| 198 | Supplying fabricating fitting & fixing Of GI Sheet 18 SWG sheet tray fixing with dash fastener of 100mm x100 mm with the help of supporting MS flat clamp 50x4 mm and clamp will be fixed on beam by dash fastener. Tray will be made/fabricated by the way of rivets, Nut/Bolts, M-Seal sealant throughly provided to make the joint of tray perfect water proof. Rate are Inclusive of all too and plants such as cutter, welding set, power hammer, driller, drilling machine etc scaffolding, transportation of materia to the site or work and rate a o inclusive of all skilled and unskilled labours. Work Shall be carried out as per directions of Engineer. Rates are a o inclusive of all lead lift ascent and descent etc, complete as per instruction of Engineer-In-Charge. |
| 199 | Applying 2 coat of crystalline coating a cementations, brush applied, water proofing treatment for concrete. When It is mixed with water and applied to concrete, it penetrates into the concrete mass protecting against the passage of water ( 5 part powder 2 part water) on dry concrete. The rate are inclusive of cut and fillet with cement mortar 1:2 mixed with polymer base water proofing compound in proportion as as specified and finish smooth. |
| 200 | Providing and fixing 300 mm SS gating of length as per architectural drawing with 3 mm thick 304 Grade SS pressed plate with 6 mm wide slits @ 15 mm with 35 mm x 35 mm x 5mm SS grade 304 tube section welded all round edges and at suitable interval for support, flushed with floor finished including providing and fixing necessary MS angle frame etc complete as in drawing (for payment purpose only SS item Shall be measured.) |
| 201 | Providing and fixing SS Grating with 3 mm thick 304 grade SS pressed plate with 6 mm perforation @ 12 mm c/c over grade 304 SS frame of size 35mmx35mm x 5mflushed with floor finish including providng ard fixing necessary MS. angle frame etc. complete as per drawing (for payment purpose only SS Item shall be measured ) |
| 202 | 300mmX300mm/200mmX200mm/150mmx150mm |
| 203 | Polishing and buffing of SS 304 railing/ SS surface of provided in RRTS stations with minor grinding (as required) and removing stains/blemish with proper rubbing and polishing the surface with suiatable material & finally buffing the surface with high speed buffing machine using buffing material as per direction oo Engineer-in-charge. The work will be carried out In non revenue hours and rates are inclusive of all taxes, man power, material, too and plants, CO and OH etc all complete. |
| 204 | Cleaning of chocked drains including removing of covers, cleaning of silt, mud, rubbish etc and refixing of top cover. All work complete including removing and disposal of silt as per direction of Engineer-In-charge for size width (300 to 450mm) depth upto 500 mm. |
| 205 | Cleaning of chocked drains including removing of covers, cleaning of silt, mud, rubbish etc and refixing of top cover. All work complete including removing and disposal of silt as per direction of Engineer-In-charge for size width (500 to 1000mm) depth upto 600 to 1200mm. |
| 206 | Cleaning of septic tank as per direction of Engineer-In-Charge. |
| 207 | Patch work of exterior texture paint GRANULES FINISH of approved brand and texture including repoval of pid work. Preparation of surface prime and base coat. Complete as per direction of Engineer-In-Charge (work upto 4m height). |
| 208 | Extra for texture painting and coating for work above 4m height and upto 20m height. |
| 209 | Providing and applying poly urathene (PU) coating on concrete floor.1. Surface preparations: Mechanical cleaning of surface using wire brush as required to clean minor debris/dust/dirt from the surface including repair of concrete/base surface wherever required.2. Epoxy Primer: Application of high viscocity, solvent free fast curing epoxy primer by brush/roller covering the prepared surface. 3. Top coat: Application of two componant polyurthane coating in 2 coat of min 75 microns each. |
| 210 | Providing and fixing 6 lever/pin cylinder mortice lock cylinder as per direction of Engineer-In-Charge. |
| 211 | Providing and fixing 6 lever/pin cylinder mortice cylinder/latch set complete with door strike/lever/handle/screw etc. complete in stainless steel of approved manufacture for the on panel/solid and g;azed door etc. including all fixing and other accessories as required and as per drawing/specifications and as directed complete. |
| 212 | Providing and fixing 800mm dia TO mirror covered with powder coating covering having sunshade of 45mmx45mmx2mm thick squared tube as hanging member and 50mmx50mmx2mm tubular parts as adjust with welding and V Shaped welded support to station roof at the location as per direction of Engineer-In-Charge the rate are inclusive of all taxes duty etc. Nothing extra shall be paid. |
| 213 | Providing and fixing of 2 mm thick SRBG/aluminium sheet cautionary retro reflective sheet on RCC pier with all T&P, staging, destaging, fasteners, manpower, PPE's etc. all complete and as per direction of engineer in charge. |
| 214 | Core cutting work at viaduct deckslab/OHE parpaet location as per requirement with HILTI machine diamond cutter in RCC str., complete in all respect as per direction of engineer in charge. |
| 215 | 75 mm dia upto 200 mm |
| 216 | 52 mm dia upto 250 mm |
| 217 | 150 mm dia upto 200 mm |
| 218 | Providing and fixing of Bottle trap of approved make as per directions of engineer in charge. |
| 219 | Restoring water supply in toilet and bath room or kitchen or any other place by using pressure machine pump/other equipment by clear the lockage etc. in line. |
| 220 | Repairing of broken/cracked PVC water tank of capacity 6000-10000 litre by plastic welding with same tank material, removing of tank connection and refiting of same tank after repair work and other charges all work complete as per direction of engineer in charge. |
| 221 | Providing and fixing of PVC water tank cover with all fittings complete as per direction of engineer in charge. |
| 222 | Repairing of bib cock or angle valve by taking out rusted damanged knob and fixing of new knob assembly of Parko make or equivalent as per direction of engineer in chage. 15 mm nominal bore. |
| 223 | Providing and fixing Dorma or equivalent make Panic bar for double leaf door. |
| 224 | Supplying, fabrication, fitting and fixing FRP sheet 4 mm thick. Rates are inclusive of all too , plants such as cutter, welder, generator set supply, drill power hammer, drilling mcahine, cutting scaffolding, tranportation of material to site of work and rate a o inclusive of all skilled and unskilled labour work & to be carried out as per direction of enginner in charge. Rates are inclusive of all night charges, lead, ascent and descent all complete. FRP sheet will be fire retardant and certificate is to be submitted. Work includes scaffolding charges for removing of old MS sheet & submission at designatged place and duties complete. |
| 225 | Deployment of Tractor mounted Broomer for cleaning of Roads |
| 226 | Supply and filling Diesel in Tractor mounted Broomer for cleaning of Roads (Diesel actually consumed as per log book shall be measured for payment) |
| 227 | Providing and installing Omega Joint for expansion of 50 mm confirming to IRC-83 Part-II in ramp and at grade portion all complete and directions of engineer-in-charge |
| 228 | Design, supply, fabricating and installing in position Glass Canopy using 13.52 mm (6+1.52+6 mm) thick laminated glass over SS 304 grade sections / beam / frame /tubes of fixed to RCC structure using, SS/GI M-16 and M12 approved make fasteners and Nut Bolts as per approved design and drawings. Glass shall be clear, toughened and laminated with 1.52 mm thick polyvinyl butyral layer fixed to SS frame using 4 way / 2 way SS 304 grade spider fittings, tensile cable, other fittings etc as per specifications, including filling non-staining water resistant clear silicon filling at glass joints and other gaps etc. complete as per approved design and drawing and as per directions of Engineer in Charge akin to Glass Canopy in Admin Building Entrance |
| 229 | Design, supply, fabricating and installing in position Glass Canopy using 13.52 mm (6+1.52+6 mm) thick laminated glass over SS 304 grade sections / beam / frame /tubes of fixed to RCC structure using, SS/GI M-16 and M12 approved make fasteners and Nut Bolts as per approved design and drawings. Glass shall be clear, toughened and laminated with 1.52 mm thick polyvinyl butyral layer fixed to SS frame using 4 way / 2 way SS 304 grade spider fittings, tensile cable, other fittings etc as per specifications, including filling non-staining water resistant clear silicon filling at glass joints and other gaps etc. complete as per approved design and drawing and as per directions of Engineer in Charge akin to Glass Canopy in Admin Building West Side |
| 230 | Design, supply, fabricating and installing in position Glass Canopy using 13.52 mm (6+1.52+6 mm) thick laminated glass over SS 304 grade sections / beam / frame /tubes of fixed to RCC structure using, SS/GI M-16 and M12 approved make fasteners and Nut Bolts as per approved design and drawings. Glass shall be clear, toughened and laminated with 1.52 mm thick polyvinyl butyral layer fixed to SS frame using 4 way / 2 way SS 304 grade spider fittings, tensile cable, other fittings etc as per specifications, including filling non-staining water resistant clear silicon filling at glass joints and other gaps etc. complete as per approved design and drawing and as per directions of Engineer in Charge akin to Glass Canopy in Depot Station Entrance |
| 231 | LUXALON® 300C Curved Aluminium Ceiling System with standard perforation: Supply & Installation of Luxalon® 300C Curved Aluminium with standard perforation Ceiling system in Polyester Coil Coated Finish in approved RAL code color, consisting of Panel 300mm wideX 30mmdeepX 0.7mmthick made up from corrosion resistant aluminium AlloyAA3105 with bevelled edges having panel length upto 6mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed for higher strength and good roll forming characteristics. The29mm high upstands at the panel ends are to provide enhanced rigidity. Panel shall be fixed to a baked enamelled aluminium carrier of 41.5mmwide x 62mm deep x 0.95 mm thick in standard length of 5mtrs. made of double baked stove enamelled aluminium manganese alloy AA3005/3000series/5000series by locking clips to hold the pane , providing a rigid system which is able to withstand wind pressure. TheConsultant/Client should provide the design windpressure/load of the project to decide the panel and carrier span. TheCarrier shall be fixed directly on MS/GI substructure which shall be provided by the MainContractor/Client.300C Ceiling product should be GreenproCertified: For LEED certification by Indian Green Building council(IGBC).Ceiling manufacturer should provide GreenProCertification of the product. The manufacturer should be ISO9001:2015 Quality Management System Certifications compliant with in house testing facility and should have their own manufacturing plant in India. The coated coil is passed thru SixHi configuration roller leveling process to ensure the flatness of the coil. Measurements shall be wall to wall without any deductions for lights, diffusers, columnset. PaintFinish: (item desc. contd...) |
| 232 | Paint Finish: Aluminun panels shall be chromatised for maximum bond between metal and paint enamel twice under high temperature, one side with a full primer and finish coat, the otherside (innerside with a primer coating and skin coat on a continuous paint line. The coils from which the aluminum panels are to be cold rolled formed shall be stove enameled on continuous coil coating paint line with dried in place roller coated application for pretreatinent The coils to go through four stages of pretreatment, three times oven baked through conversion coating, priming and finishing coat, ensuring superior adhesion, high corrosion resistance and good colour retention. The coils shall be painted on both sides after being degreased. Prime coat of at least 5 microns to be applied at both sides, and a black coat of 5 microns of neutral colour to be put on the inner surface and 5 microns of binder and 15 microns of top coat of desired colour shall be additionally provided on the expose surface etc. complete as per directions of Engineer-in-charge. Measurements shall be for exposed ceiling surface without any deductions for lights, diffusers, columns etc |
| 233 | Fabricating and supply of stainless steel (conforming to grade SS 304L satin finish) four seater bench without backrest as per drawing. |
| 234 | Providing and fixing of PU tactile tiles of approved brand and manufacture in standard tile size of 300x300x2.5mm |
| 235 | Providing & fixing C.P. brass towel rail 24\\" as per approved makes |
| 236 | Providing & fixing C.P. Brass twin robe hooks as per approved makes |
| 237 | Providing & fixing SS hinged grating, 6 mm thk with frame (near Cat No NRG 7009 approved equivalent) including setting in floor with cement mortar 1:3 |
| 238 | Providing and fixing of Parryware brass Health faucet Slimline wth hose and hook (Chrome Finish) E8383A1 of approved make |
| 239 | Providing & fixing of Parryware Trigon Angle Valve T9828A1 With Wall Flange (Chrome Finish), Silver |
| 240 | Providing and fixing of Parryware Bottle Trap Set with Outlet Pipe for Bathroom base kitchen sink Wash basin T3201A1 (Chrome Finish) |
| 241 | Providing and fixing white vitreous china extended wall mounting water closet make Hindware Cora Vortex Catalogue part no.92569 |
| 242 | Providing and fixing of Parryware CISTERN LINEA PLUS E812099-WHITE of approved make |
| 243 | Complete arrangement for lifting and lowering the span for replacement of confined elastomeric pressure pads/Pot PTFE bearing/repairing and replacement of installed Pot PTFE bearings with suitable anchoring mechanism including removing & tightening of bolts etc. by providing and operating suitable hydraulic jacks ( manual/ motorise) of minimum capacity 250T-300T with check nut, tilting saddle and hydraulic power pack ( as approved by NCRTC),MS steel stool/ wooden blocks of hard wood ( Saal/ Teak), packing plates as per requirement including cleaning of pier caps after completion of lifting work. The rates include all other items i/c too , water.electricity, safety net all around etc. complete in all respect as direction of in-charge. The entire work shall be executed within approved method statement or any modification as directed by engineer in charge. The rates include the complete cost of providing & operating diesel operated skylift of required boom length required for this work.The sky lift shall be provided till the completion of work and no fixed hours are specified. The safety and security of all equipment/machinery/material will lie with agency. The lifting work will be done in block hours.Note: The payment under this item shall cover lifting of one end of span for repairing of one or more bearings /pedesta at that end. The payment of scaffolding around the pier/pier cap shall be paid extra as per relevant DSR 2023 item. |
| 244 | Providing & fixing Pink vinyl sheet taping/signage, as per directions of Engineer in Charge |
| 245 | Providing and applying silicon as per the instructions of Engineer in Charge including cleaning of required surface, taping, removal of lapping, all too lie gun etc. all complete |
| 246 | Desilting of open drains, covered drains pipe drains, etc by taking out silt, building rubbish earthmix, dead anima , plastic bags and all type of semi solid malba/rubbish from flowing water including opening and closed of drain cover stacking within a lead of 50m and lift upto 1.5 m in foul condition including pumping out water as per direction of engineer in charge quantity measured in stack shall be reduced by 8% for voids for payment (all other temporary work are inclusive) |
| 247 | Providing & fixing in position precast Concrete Jali along with green area on road of size 1500 mm (height), nun (width) 65 mm (Thick) concrete grade M25, Minimum reinforcement of 3-7 kg steel, 3 sides shuttering steel compacted accurately designed molds appropriately reinforced with M-25 grade Concrete as per approved design & drawing. Complete as per direction of engineer-in charge |
| 248 | Supply and Erection of Precast Prestressed Boundary Wall by using columns of size 150 x 150 mm H-Section with 7 bars of 4 mm HT Steel and precast planks of size 2100 x 300 x 50 mm with 3 bars of 4 mm HT Steel of up to 2.40 mts height with Columns and Planks using M-30 grade of concrete including transportation, loading, unloading etc. (Excavation for foundation and foundation concrete shall be paid separately under relevant BOQ Item) |
| 249 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 1200x600 mm. |
| 250 | Grouting the joints of flooring/wall tiles having joints of 5mm width, using epoxy grout, including filling/ grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 1200x600 mm. |
| 251 | Providing and laying full body Vitrified tiles in floor of minimum thickness 15 mm with water absorption less than 0.06% and conforming to IS: 15622, of approved brand & manufacturer,laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints.The slab must be cut with the zero chipping diamond cutter only. Laying of slab will be done with the help of notch trowel, weddge, clip of required thickness, vacuum cups for lifting, leveling system and rubber mallet for placing the slab gently and easily. Size of tile 800x2400 mm of all colours and shades. |
| 252 | Providing and fixing Glazed Vitrified tiles premium quality (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in Wall, skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 1200x2400 mm |
| 253 | Providing and fixing wash basin with C.I. brackets, 15 mm CP Brass pillar cock, 32 mm CP Brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the wal wherever required. White Vitreous China Flat back wash basin size 580x430 mm of approved make of hindware Cat. No.10080,with single 15 mm CP Brass pillar cock. |
| 254 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in Full Body Vitrified slab of 15 mm including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 255 | Providing edge Nosing /moulding to 15 mm thick Full Body Vitrified slab counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-inCharge. |
| 256 | Deployment of manpower for various enabling, repair works in priority section including housekeeping, plumbing, multi tasking works etc.Note - Payment of wages shall be made as per rates mentioned in latest order of the CLC office. |
| 257 | Supply, transportation and installation in the position of fall arrest/ horizontal lifeline on roof sheeting for upto 3 users at a tine with shock aborbers, intermediate support post @10m interval, length & width of post 400mm, height 100 mm and material shall be SS 316 grade and its base plate shall be 3 mm thick GI with 400 gsm &600 kg capacity, including all required accessories with complete finish as per IS 3521:2021 (Part 8) as per directions of Engineer-in-charge |
| 258 | Providing Finishing and painting with Floor paint two or more coats including Cleaning the surface and removing dirt, dust, bird dropping etc.(1)on Paver Blocks work. |
| 259 | Providing ,Finishing and painting floor top coating on Paver blocks, Stone and tile Topcoat of approved brand and manufacture after drying of surface with necessary cordoning or area complete. |
| 260 | Providing and fixing 12mm thick clear toughened glass including all fittings & fixtures all complete including all leads & lifts up to the required location as per drawing and direction of engineer in charge. |
| 261 | Supplying and Installation of steel pole rounded Dustbin with cap of capacity 60 litre in station building at various locations and levels. |
| 262 | Cutting of RCC wall , slab by diamond cutting system wire saw/wall saw method including lowering & lifting of cut segments |
| 263 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 12 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.a) 12x150mm |
| 264 | Constructing brick masonry road gully chamber 60x60x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 600x600 mm pre-cast SFRC Cover and frame complete as per standard design : (With common burnt clay F.P.S. (non modular) bricks of class designation 7.5) |
| 265 | Constructing brick masonry road gully chamber 90x80x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 900x800 mm pre-cast SFRC Cover and frame complete as per standard design : (With common burnt clay F.P.S. (non modular) bricks of class designation 7.5) |
| 266 | Providing and fixing vertical grating of Cast Iron size (300x300mm) for Bell mouth of Drainage including finishing with cement mortar 1:3 (1 cement : 3 Coarse sand) as per Direction of Engineer-in charge : |
| 267 | Supplying and laying of door Mat 3M 7150 at entrance gates at Entry exit PD level and Concourse lvl at NCRT stations. |
| 268 | Providing and Fixing 110 mm dia. SWR(Type-B) pipes conforming to IS: 13592 including all fitting such as bends junctions, cowls, clean out plugs, offsets,etc. jointing with solvent cement including fixing at all level/ celling level with man lifter supported by steel camps & hangers etc. including cutting chases and making good the same after pipe have been duly laid complete in all respects. |
| 269 | Providing Fixing and jointing 200 mm dia. SWR(Type-A) pipes conforming to IS: 13592 including all fitting such as bends junctions, clamp, anchor fastener,hanger rod, plugs, offsets, etc. jointing with solvent cement including fixing at all/ celling level with man lifter supported by steel camps & hangers etc. complete in all respects. |
| 270 | Fixing of modified viaduct central railing including shifting from casting yard, Loading, unloading, lifting to viaduct, placing in position etc. all complete during block hours (4-5 hours) as per direction of engineer-in-charge |
| 271 | Painting with Dekguard paint at welded joint with surface cleaning/preparation and applied (two coats) as per manufacturer's specifications complete.On Railing. |
| 272 | Grinding, Finishing, Cleaning of all Bearing Pedestals including the removal of extra grout/concrete from the pedestals and minor repair with the approved structural binding materials.The item also includes the cutting of extra steels from Pier Caps & their finish,Cleaning of all seleeves in pier Caps and their Grout, Minor Repair of shear Keys, Segment, Recess Filling, Pier caps etc. complete in all respects as per the direction of engineer in charge. |
| 273 | Cleaning & buffing of kota and granite stone including labour, material, all complete in all respect as per the direction of Engineer in charge. |
| 274 | Providing filling of pigments of same colour of stone in joints of granite after removal of existing grout matirial including. |
| 275 | Design, Supply, fabricating, installing in position Stainless steel material SS 304 grade sections/ beam / frame /tubes of fixed to RCC structure using, SS/GI M-24 approved make fasteners and Nut Bolts as per approved design and Drawings for fixing of 12mm thk UV protected polycarbonate sheet complete as per approved design and drawing and as per direction of Engineer in Charge (The cost of fixing of polycarbonate sheet and SS/GI M-24 fasteners will be paid in separate item ) |
| 276 | Drilling of holes 30 mm dia. In Reinforced cement concrete with power driven drill machineto a depth of 200 mm in RCC beams, lintails , columns and slabs to introduce M24 X300 anchor fasteners of Hilti make for errection of PEB members for FOB& staircases incl. fixing the anchar fasteners in position using injectable mortar of HILTI make (Model no. HY 200-R v3), all complete as per directors of Engineer-IN-Charge. Rate is including the cost of the HILTI make anchor fasteners and all materials, machinary and labour and fuel all complete as per directions of Engineer-in-charge. |
| 277 | Providing and fixing 12 mm thick Solid clear UV2 coated polycarbonate sheet in canopy at Ground level over S.S frame as per specifications, drawings and direction of Engineer-in-charge complete. |
| 278 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required..Group C |
| 279 | Supply, laying, testing and commissioning of 1100 V grade, armoured, FRLS, XLPE, Aluminium (Al) / Copper (Cu) Conductor cables on existing trays/ walls/ columns /indoor /trenches including the cost of supports with suitable clamps, saddles, hooks, bolts etc. and including the cost of proper dressing of cables, markers providing identification tags, earthing of glands armouring etc. complete as per specifications, 3 core 6 sq mm Cu Conductor . |
| 280 | Providing and fixing single/multistage submersible tubewell pump of 3 HP,suitable for 150 mm bore with stainless steel casing, noryl impeller, stainless steel shaft built in non return valve coupled with submersible squirrel cage motor suitable for 145V +/- 10% volts, AC supply . |
| 281 | Providing and fixing 8mm thick Solid white colour polycarbonate sheet with 50 Mic. both side UV coating in vertical façade of required size by suitable arrangement at Concourse level over existing Structural M.S frame as per specifications, drawings and direction of Engineer-in-charge complete. |
| 282 | Providing and fixing Wood Polymer Composite (WPC) Louver Panels size 12mm thick as per approved color and fixing as per manufecture specifications all are complete as per direction of Engineer-in-charge. |
| 283 | Providing and fixing Laminated Wooden Flooring (approved shade make, made, color amd texture) on the floor and skirting (Plank Type) size of tile 1285mmx191mm as per approved, AC-3, core-HDF, the thickness of tile 9mm, tile fixing with tong and groove systems, as per manufecturer specification and direction of Engineer-incharge. |
| 284 | Providing Fixing and jointing 160 mm dia swr (Type-A) UPVC Pipes conforming to IS:4985 Class-5 including all fiting such as bends junctions,clamp,anchor fastener,hanger rod,plugs,offsets,etc,jointing with solvent cement including fixing at all/celling level supported by steel camps & hangers etc,including cutting, chases/holes in floors /walls /slab and making good the same after pipe have been duly laid complete in alll respects. |
| 285 | Hire charges for supply of boomlift of 120 feet on monthly basis, i.e. 10hrs. Shift for 26 days with one operator. The rate shall be include diesel charges and operator with all safety precautions complete and mobilisation and demobilisation and movement of manlifter at site. |
| 286 | Design, Supply and Execution of Hand painted work (Graffiti Art) on Piers, Walls and Pier arm/caps. With approved make of paint, including preparation of surface like putty, plaster,cleaning, trowel etc. and inculding all accessories, scaffolding, safety harness etc. Complete in all respects as per direction of EIC |
| 287 | Providing of Impact Protection Vehicle including maintenance and operator. |
| 288 | Providing and fixing signage plate of required size at different places inside & outside the building (at any height in the existing building). Signage plates shall be 2mm thick white colour acrylic sheet printed text/ graphics or vinyl pasted text graphics as per approved design font text size and quality complete as per direction of engineer in charge. |
| 289 | supply and installation of face mounted signage made from 8mm clear acrylic sheet digita l print install with 20mm SS Studs 1800mmx1200mm (payment to be made as per surface area) |
| 290 | Pin board 3'x2' |
| 291 | Pin board 6'x4' |
| 292 | Providing and fixing of high intensity micro prismatic retro reflective market sign boards as per ASTM-D-4956-09 of required size (600mmx900mm) for tunnel plaque made out of minimum 2mm thick aluminium/ACP sheet , face to be fully covered with yellow colour high intensity micro prismatic retro reflective market sign boards as per ASTM-D-4956-09 with MS support frame. the support frame shall be made of MS angle/Flats/tube /Channel/built up section as suitable for installation of board on concrete surface. the MS support frame shall be properly painted with a coat of anti-rust primer synthetic enamel paint as per the drawing specification and direction of engineer in charge. |
| 293 | Providing & Fixing main facade channel letter fabrication & supply of 2mm thick white acrylic sheet & 2.5 mm aluminium base letter to be made out complete as per approved design and direction of Engineer in charge. |
| 294 | Supply and installation of photo frame signage 600x450mm (wall mounted ) made of Aluminium 2mm clip on with Clear Acrylic Digital Print. The Signage print is to be changeable all complete as per specifications and direction of engineering in charge. |
| 295 | Supply and installation of photo frame signage 300x450mm (wall mounted ) made of Aluminium 2mm clip on with Clear Acryliyc Digital Print. The Signage print is to be changeable all complete as per specifications and direction of engineering in charge. |
| 296 | Providing and fixing plated type Graphics sigh made out of 1.5 mm thick SS 304 grade stainless steel, fabricated to reqired size and shape, incluiding corners and edges properly rounded and dressed. Item to include chemical etching to desigated graphics/text to RCC/Wall surface,steel/Wooden doors as required with the stainless steel counter sunk cross headed screws of required length and dia. including providing necessary washers, PVC/Rubber spacers etc. all acnhor fasteners, bolts etc to be SS304 grade. (350 mm X 200 mm) |
| 297 | Statutory signs: 150 mm X 300 mm (payment to be made as per surface area) |
| 298 | Providing and fixing graphics printed on Opaque Vinyl directly pasted on the glass surfaces. Printed over Opaque self-adhesive vinyl as per artwork and completed and laminated with protective over laminate as specified and duly approved by Engineerin charge. Cost to include fixing of sign at location on to glass surface including its cleaning, marking, alignment, complete as specified in drawings and at locations approved by the Engineer-in-charge |
| 299 | Time Table-375 mm x 300 mm (payment to be made as per surface area) |
| 300 | Train Timing -600mm x 300mm (payment to be made as per surface area) |
| 301 | Prohibited item -400 mm x 300 mm (payment to be made as per surface area) |
| 302 | (I) sign -300 mm x 300 mm (payment to be made as per surface area) |
| 303 | Save Paper Nature -200 mm x 200 mm |
| 304 | Diaper changing Station -450 mm x 250mm (payment to be made as per surface area) |
| 305 | Providing and fixing graphic type sign made out of 1.5 mm thick SS-304 grade Stainless Steel with chemical etching to design plate with Square pipe 50 MM 1.5 RMT S.S.-Tree Plantation Sign Size 300x450 mm |
| 306 | Providing and fixing of footsteps Graphics Vinyl finish as per approved colour and design wilh lamination make 3M/L.G wilh digital printing size 300x300 mm-Foot prints (payment to be made as per surface area) |
| 307 | Providing and fixing of Ractangular graphics mentioning station name size-1200x600 mm-Rectangular Graphics |
| 308 | Illuminated Suspended Signs:Providing and fixing Illuminated signs including all operations from fabrication to installation all complete as per relevant drawings, technical specifications, signage and graphic schedule and to the satisfaction of the Engineer-in-charge. Sign frame: Sign frame shall be made of modular Aluminium extrusion of minimum 2 mm wall thicknesss section providing and fixing of all accessories such as nuts, screw hooks, slots etc. The Modular Design Signages is to be suspended from the concrete (e.g., slab, beam, trusses etc.) by Mild Steel (MS) Suspender pipe including all accessories like bottom plate, locking plate, adjuster, bolts etc. (Suspender to paid separately udner separate item). Hilti fastener or equivalents brand of specified diameters are to be used where anchoring is to be done with the concrete chamber. VHB Tape/The inside edge of sign frame to have EPDM gasket where it gets in contact with the sign panel as per approved design.The Modular Design Signages have its openable profile of 80mm for double sided shall be made of Aluminium extrusion of minimum 2 mm wall thickness. The frame shall be snap/bolted fit and easily openable for maintenance and shall be designed to resist opening in heavy wind flow. Sign Panel:B) For Elevated/ Underground Station:Providing and fixing sign panel made out of The message on 3M/LG equivalent Cast Blackout Vinyl and Coloured Vinyl Translucent as per colour standard specified by Engineer-in-charge pasted on Polycarbonate/Acrylic 4MM Sheet (Pioneer or Polyleathers or Laxan or PC Lite or equivalent brand) of 4mm thickness is to be used on one side of panel and other side of panel will be of Aluminium Composite Panel (ACP) Sheet of 3mm thickness. For double-sided signage, where graphics / text are to be provided on both faces, the sign panels as described above are to be provided on each side of the sign frame. Clear laminate layer cover with minimum 25mm overlap around edges of Poly Carbonate sheet to be provided over graphic.Letters of the Vinyl message to be made with plotter cut self-adhesive cast colour Vinyl. Signage shall be illuminated from back wherever specified using Single/Multiple LED Modules each with IP 65 protection of white colour . Modules should be uniformly placed in a manner that at least one LED Module every 12 16 sq. inch of surface required illumination. Each signage should will have an individual power supply adaptor for illumination of all LED installed in signage. The power supply adaptor should be placed inside signage and power supply adaptor should be connected using plug-in type connector connected to mains supply. LED to be used with three-years replacement warranty make of LED module and Driver SAMSUNG/VIN/OSRAM/UNION 2100x400x80mm Double Sided Each 21495.21 11.0 236447.31 |
| 309 | Taking high definition images/photos of bearings, pedestals and shear restrainers on piers/ portals of viaduct including submission of annotated inspection report with identified details & anomalies like cracks, spalling, honeycombing etc. as per direction of Engineer under GGM/O&M/Civil for Delhi-Ghaziabad-Meerut Namo Bharat Corridor. |
| 310 | Warning tactile indicator: Supply and installation of warning tactile indicator on the walking surface in a raised grid pattern of 'dots' or studs made of SS 316 grade steel. The dots shall be placed at centre to centre distance of 60 mm, measured along one side of a square arrangement.Size of stud: 35 mm (dia) X 4.5 mm (thk)Underside: 6mm (dia) X 12mm (length)Pattern: cross hatch/circle pattern/diamond patternAll works to be carried out as per the directions of Engineer in Charge. |
| 311 | Directional tactile indicator: Supply and installation of directional tactile indicator on the walking surface, consisiting of raised bars oriented to the direction of movement, made of SS 316 grade steel.Size of bar: 280 mm (straight length) X 35 mm (width) X 4.5 mm (thk)Underside: 3 (no. per bar) X 12 mm (l) x 6 mm (dia)All works to be carried out as per the directions of Engineer in Charge. |
| 312 | Providing and fixing fabric covered perforated 8mm MDF board fixed to GI metal frame of 50 X 50 mm making a grid of 600mm c/c. The frame is to be made in proper line after levelling. The panels will be backed with 50mm Polyfibre/ Glasswool Acoustic Wadding 1000 GSM inserted inside the grid of 610X610mm. The base upto 900 mm shall be painted 12mm MDF fixed over the G.I frame with 100mm vitrified tile skirting complete in all respect as per direction of Engineer in charge. |
| 313 | Carpet Flooring Supplying PP Carpet Tiles. Size of tile should be combination of 600x600mm carpet tiles & 180x1200mm plank as per approved make & designs including aluminium profile at the floor transition places, complete as per approval / direction of Engineer-inCharge |
| 314 | Fixing of carpet tiles including cost of adhesive of approved quality on vitrified tile floor, complete as per direction of Engineer-in-Charge |
| 315 | Providing and fixing Laminated wooden flooring(approved shade, make, color, and texture), on the floor and skirting (Plank Type) size of tile 1285mmx191mm or as per approved, AC-3, core -HDF, the thickness of tile 9mm, tile fixing with tong & grove systems, as per manufacturer specification and direction of Engineer-in-Charge. |
| 316 | Providing and Pasting Decorative wall paper of approved Quality,Shade,Design,Colour on walland/Other SurfaceComplete as per Direction Of Engineer-in Charge. |
| 317 | Providing and fixing Acrylic Sheets of approved color, Design, and Shade( Royal Touche or Equivalent)for wall Panelling(Interior Work), groove on the laminate, etc. as per the approved color and texture, all complete as per the direction of the Engineer-In-Charge. |
| 318 | Providing & fixing laminated beading profile with headless nails above the wall panelling complete as per direction of Engineer-in-Charge |
| 319 | Providing and fixing of the MF acoustic treatment for the walls with 12mm com ply over the surface of the existing walls by means of nylon sleeves and necessary screws. Final finishing facia to be 9 mm PET acoustic panel of desired colour glued over the ply with SH/SR adhesive of pidilite or equivalent. The work to be done as per the design and colour selected by the Architect |
| 320 | Supplying ,Installation ,Testing and Commissioniong of GI Raceway of following size as required and as below: 200mmX40mmX 2.0mm with cover 2.0 mm |
| 321 | Supplying ,Installation ,Testing and Commissioniong of GI junction box of following size as required and as below: 250mmX 50mmX 2.0mm with cover 2.0 mm |
| 322 | Providing an Emergency Response Team comprising 1 Engineer, 2 supervisors and 2 labours along with an emergency response vehicle (a 4 X 4 Camper - Mahindra/ISUZU or equivalent) including driver, maintenance, AC, permits -round the clock for 4000 km run/month but excluding taxes/tolls/parking (to be paid on actuals) alongwith tools and equipements to attend site within Delhi-Meerut Namo Bharat Corridor, as per Directions of Engineer in charge. Total of Schedule - B (excl. GST) = 66908872.12 66908872.28 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysOct 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender