Tender For special Repair To Bldg No Np-23 (Jco Mess) Np-45 (Washerman Shop) And Fol Gp Office Of Certain Mil Unit Under Ge (S) Binnaguri
Tender Value
19.90 Lakhs
Estimated cost
Bid Submission
15 Sep 2026
13 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No Np-23 (Jco Mess) Np-45 (Washerman Shop) And Fol Gp Office Of Certain Mil Unit Under Ge (S) Binnaguri
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkat with shutter exc. 1.5sqm and n.exc 4sqm each |
| 2 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation board/slabs/blankets, any thickness, including cover fillets |
| 3 | Dismantling of Plain or corrugated steel sheet any gauge, thickness, including Nainital or similar pattern roof coverings sheets |
| 4 | Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing |
| 5 | Demolition of brick work built in cement mortar etc complete all as specified. |
| 6 | Dismantling timber scantlings 40 sq. cm and over in section, in any position |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 8 | demolition of cement Concrete of any description and in any position not otherwise specifically provided for |
| 9 | Demolition of cement concrete in ground floor and paving n exc 15 cm thikness(below or above ground) |
| 10 | M&L fly ash brick work with sub class 'B' brick straight or curved on plan exc 6 m mean radius built in CM 1:6 |
| 11 | M&L for Brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified |
| 12 | M&L for RCC (nominal mix ) 1:1.5:3 type B1 using 20 mm graded stone aggeregate as in ,lintels roof bands and similar item |
| 13 | M&L for RCC (nominal mix ) 1:1.5:3 type B1 using 20 mm graded stone aggeregate as in ,cill band and similar items |
| 14 | M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 15 | Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders |
| 16 | S&F steel work in Trusses, purlins, posts and the like using tubular/ square hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming I.S.1161-2014/IS 4923-1977 grade St-240 complete all as specified |
| 17 | M&L for two coat of synthetic enamel paint over a coat of red oxide primer including preparation on steel surfaces of any description over 10 cm width or girth complete all as specified |
| 18 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 19 | S & F pre painted galvalume aluminium zinc coating GI Based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in eaves board fixed with selp tapping screw as specified |
| 20 | M&L for 20 mm thick (10mm+10mm) plaster in CM (1:4) on fair faces of brick/concrete surface top layer finished even and fair without using extra cement with water proofing compound (WPC will be measured and paid separately) |
| 21 | M&L for plastering in cement mortar (1:6), 15 mm thick on brick /surfaces of other than fair face even and smooth without using extra cement. |
| 22 | Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified |
| 23 | M&L for coloured Non skid joint free ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:6 complete all as specified |
| 24 | M&L for coloured Non skid joint free ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but nexc 0.38 Sqm, vertical surfaces, in skirting etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match including 10 mm thick rendering in cement mortar 1:4 complete all as specified |
| 25 | S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125 x60 mm |
| 26 | M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregate as in bed blocks for fixing holdfast or filling hollow space of steel frame etc all complete as specified |
| 27 | S&F for plain, framed, factory made panelled shutters 35 mm thick (any number of panels) , with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats. |
| 28 | S&F seccond class hardwood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded.fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified |
| 29 | Suply and fixed stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples complete |
| 30 | S&F Stainless steel butt hinges medium weight 100mm long complete all as specified |
| 31 | S&F Aluminium anodized barrel tower bolts, extruded section 200mm long complete all as specified |
| 32 | S&F Aluminium anodized handles, D type, 150mm long complete all as specified |
| 33 | S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 34 | S&F Powder coated aluminium window sliding type three track (2 glazed & one gauze shutter ) aluminium sections weighing not less than 1.67kg/m for frame and 0.55 kg/m for shutter including necessary jointing cleats, glazing cleats, rubber packing , screws, handle, locking arrangement and 4 mm thick plain/tinted glass and aluminium mosquito proof gauge including taking down of old existing steel window and making good disturbed surface of wall complete all as specified |
| 35 | S&F Powder coated aluminium louvered ventilators of size 600X600mm with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified |
| 36 | M&L applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of white primer including preparation of new /old wall surfaces complete all as specified |
| 37 | M&L for applying two coats of oil bound distemper over one coat of primer on walls including preperation of new or previously untreated surfaces complete all as specified |
| 38 | S&F 4 mm thick Non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium frame work with screws |
| 39 | S&F Anodised aluminium snap grid frame work for false ceiling for size of grid 605 x 605 mm all as specified |
| 40 | M & L preparation of old surface & applying one coats of synthetic enamel paint wooden surfaces exc 10 cm girth all as specified |
| 41 | M&L for 75mm thick PCC type C-2 , 1:3:6 (40mm graded stone aggregate) al in plinth protection/ foot path finished even and fair without using extra cement all as specified |
| 42 | M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in surface drain including forming fair finished to drain channel. |
| 43 | S/F in repair vitreous china wash basin, white flat back, size 550x400mm including brackets,cutting for and pinning in ends of brackets or erecting stand , 32 mm dia of discharge pipe, Waste coupling of PTMT (half or full threaded) all as specified |
| 44 | S&F for vitreous china wash down water closet (EWC) pan (pedestal pattern) white, including seat cover, closed pattern with flat bottom and cover with chromium plated hinging device and flush pipe, necessary connection to drain pipe, flushing pipe etc complete all as specified |
| 45 | S&F in repair Water Closet (squatt pattern) of vitruous china squatting pan of pattern \\"ORRISA\\" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified |
| 46 | S&F in repair of PVC low level flushing cistern, 10 ltr capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, long flush pipe of PVC to suit flushing cistern ( long bend) etc complete & connecting to WC |
| 47 | S&F 600 x 450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC bldg board or commercial plywood and fixed to wooden plug with chromium plated brass screws & cup washers. |
| 48 | S&F in repair of PVC connections 15 mm size with PTMT nuts of length 600 mm. |
| 49 | S&F in repair 15 mm fancy type pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore. |
| 50 | S&F in repairs bib taps 15mm bore fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified |
| 51 | S&F in repair for PVC floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet 100mm) all as specfied |
| 52 | S&F in repair of swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified . |
| 53 | Supply & fix in repair angular stop cock made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as specified |
| 54 | S&F tubular towel rail 20mm dia D type, Brass Chromium Plated 60 cm long between flanges. |
| 55 | Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc complete all as specified and as directed of following bore:- |
| 56 | (a) Bore tubing 15mm |
| 57 | (b) Bore tubing 20mm |
| 58 | M & L for steel tubing medium grade,galvanised fitting fixed complete to walls and ceiling or floor complete for this following. |
| 59 | (a) Bore tubing 15mm |
| 60 | (b) Bore tubing 20mm |
| 61 | Dismantling water tanks and removing to store of capacity exc 250 & n.exc 500 ltrs. |
| 62 | S & F in repair 500 ltrs rotational moulded polyethelene water storage tanks (cyclindrical vertical with closed top) incl connecting up pipes securing access covers etc as specified |
| 63 | S&F 20 in reapir mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut complete all as specified |
| 64 | S&F in repair for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as specified |
| 65 | S&F in repair for 110 mm bore PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as specified |
| 66 | S&F in repair for PVC (SWR) 110 mm vent cowl fixed to PVC Pipes etc complete all as specified |
| 67 | Supply and fix in repair CP Health Faucet of premium quality and PVC telephonic flexible tube fixed to 15mm bore pipe. |
| 68 | S&F in repair Brass CP mixer for mixing hot & cold water screweddown for iron pipeand fixed complete all as specified |
| 69 | Supply and fixed in repairs sinks with drainage board made of stainless steel 1mm thick sheet plugs, washers and waste pipe, including a pair of cantilever brackets embedded in wall with suitable size of PCC (1:3:6) type C-1 blocks and connecting union to pipe of overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all complete as specified |
| 70 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing on SI page No 156 of SSR Part-II completed. |
| 71 | S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing on SI page No.160 of SSR Part-II completed. |
| 72 | M&L for 5mm thick in CM 1:3 in ceiling finishing the surfaces even and smooth without using extra cement. |
| 73 | Taking down tarfelt incl cement mortar bedding from roof surfaces and lowering and removing the same to a distance exc. 50m and n. exc. 100m incl roughening of old concrete surface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified . |
| 74 | M&L for 10mm thick screed bed or bedding layers in cement mortar (1:4) in order to maintain proper slope over existing roof surfaces for applying single component acrylic polymer modified, finished even and smooth without using extra cement complete all as specified and as directed. (NOTE : Polymeric membrane shall be measured and paid separately under relevant item of this Schedule 'A'). |
| 75 | M & L water proofing treatment to RCC roof slab including parapet comprising of the following course of treatement / specified from bottom to top (a) Applying Bituminous primer @ 0.40 Ltr per Sqm over plastered surfaces of roof including parpet surfaces. Bituminious primer shall be 'Tar Mastic' manufactured by M/S STP LTD or 'EMW FLATE' manufactured by M/S Texsa India Ltd. (b) Over the priming coat laying one layer APP based polymeric membrance of approved manufacturer, 3 mm thick of weight not less than 3.60 Kgs/Sqm reinforced with non woven polyester fabric weight not less than 160 gms per Sqm. Polymeric members shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrance flashing. (c) Application of two coat of bituminous aluminium paint over the polymeric membrane after necessary preparation and cleaning. Note :- (i) Laying APP based polymeric membrance shall be done by torch on method or as per manufacturers instructions. (ii) A minimum overlap of 100mm shall be made at the end and 75mm shall be made at the sides of the polymeric membrance respectively and sealed all ovelaps and joints as per Manufacturers instructions. (iii) APP based polymeric membrance shall be \\"SUPER THERMOLAY\\" manufactured by M/S STP LTD or MOPLY FP manufactured by M/S Texsa India Ltd. |
| 76 | Supply & fix in repair of steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded all as specified. |
| 77 | M&L for Framed work such as grills, framed guard bars,for window by welding it to existing window frame and similar work con- forming to Fe.290.Gde-E-165 |
| 78 | S&F in repair of factory made steel windows with side hung shutters openable type including friction/projected type hinges steel handle and peg stay complete without glazing bars fixed to existiog opening and making to match as per existing surfaces. |
| 79 | S&Fof 3mm thick sheet glass panes ordinary quality n.exc 0.5sqm each fixed to steel frame complete with oil putty in square including steel pin. |
| 80 | M&L for laying machine cut kota stone slab flooring 20-25mm thick over cement screed base of 15mm thick (average thickness) in cement motar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified |
| 81 | M&L for laying machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick (average thickness) in cement motar 1:4 laid and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete all as specified |
| 82 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified |
| 83 | M&L Point wiring for Point controlled by one moduler switch with 1.5 sqmm PVC insulated FRLSH unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 20 mm dia non metallic rigid PVC conduit ( ISI marked ) concealed in wall with 1.5 mm thick pressed steel terminal boxes ( modular type ) concealed in walls painted the same inside and out side with one coat of black bitumen paint incl inner and outer moduler plate for fixing of modular switches/ regulator etc along with PVC insulated and insheathed FRLSH 1.5sqmm multi stranded copper conductor cable (green color) as earth lead |
| 84 | (a) One light point controlled by one way switch 5/6 amps. |
| 85 | (b) One ceiling fan point controlled by one way switch 5/6 amps. |
| 86 | (c) One socket out let 5/6 amps point on the same board |
| 87 | (d) One socket out let 5/6 amps point on the independent board |
| 88 | All as per item No 83 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified |
| 89 | S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified |
| 90 | S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified |
| 91 | S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified |
| 92 | S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified |
| 93 | S&F Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified |
| 94 | S&F LED Bulk Head lights fitting 1x 9/10W, 220V AC integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed etc connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified. |
| 95 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp,IP 20, class I, wall/ surface mounted, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz including connecting up with three core flexible copper conductor cable of suitable size complete. |
| 96 | S&F LED lights fitting 1x 20W, 220V AC decorative box type with driver,IP 20, class I, wall/ surface mounted, integrated type with extruded aluminium housing integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all accessories internally prewired and including necessary taking down the old unserviceable fitting complete all as specified. |
| 97 | S & F Fan Moduler step type regulator, 120W - 2 module AC 50 Hzs white/ivory finish complete all as specified |
| 98 | S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB\\"S/lsolators complete including taking down the old one complete all as specified |
| 99 | S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified |
| 100 | S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Tripple pole & neutral with din rail, IP-20 protection suitable for fixing MCB\\"S/lsolators complete includingfour pole MCCB 63 Amps with blanking plates as required and taking down the old one complete all as specified |
| 101 | S&F MCB, Triple pole Neutral TPN/FP 16 to 32A, 415 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified |
| 102 | S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘B’ curve, 10 KA all complete including taking down the old one complete all as specified |
| 103 | M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified |
| 104 | Supply and fix Exhaust fan, Steel body AC single Phase. 230V of size 300 mm sweep, heavy duty with, blades, and frame and louvers and making opening in existing wall od size suitable for 300mm sweep E/fan including connecting up with 2/3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified |
| 105 | M & L Sub main wiring concealed type with two run single core cable PVC insulated cable with 6.0 Sqmm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulated cable of stranded copper conductor of size 6.0 Sqmm connected to common earth dolly and drawing into rigid PVC conduits of 25 mm dia medium grade size, making good the disturbed surfaces complete including taking down old submain wiring.(NOTE : Two run of submain wiring cable alongwith one run of earth wire shall be measured as one length.) . |
| 106 | Taking down fan, sealing cable end,dismantling blades and removing fan and blades to store and Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust and minor repairs with parts all as specified Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysSep 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender