Tender For Special Repair Of Sarisha-Noorpur Road From Ch 0.000 Kmp To Ch 0.200 Kmp (200 Mtr) By Concrete Blocks,Under Diamond Harbour Division, P.W.D. In The Dist. Of South 24 Parganas, During The Year 2026-27
Tender Value
48.61 Lakhs
Estimated cost
Bid Submission
19 Sep 2026
8 days left
EMD
97233
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
24 Paraganas South → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair Of Sarisha-Noorpur Road From Ch 0.000 Kmp To Ch 0.200 Kmp (200 Mtr) By Concrete Blocks,Under Diamond Harbour Division, P.W.D. In The Dist. Of South 24 Parganas, During The Year 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of Flexible PavementsDismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separatelyII) By Mechanical MeansA) Bituminous course |
| 2 | Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. |
| 3 | upplying and Laying in the particular pattern of cement concrete block pavements with BIS certification and spacer nib of size and shape with aspect ratio as per IS 15658 with cement concrete grade not less than M40 on the prepared base course of specified CBR as mentioned in design and drawing with a cushion of bedding sand of 30 to 50 mm thick (grading of the bedding sand as per clause 6.5.1 of IRC SP-63) and filling up the gaps between two paver block with joint filling sand (the grading of the joint filling sand will be as per clause 6.5.2) complete as per IRC SP - 63 with proper confinement of bedding and joint filling sand, compaction,levelling and filling up of the edge gaps with mortar. Type I, II,III, IV should be as per design requeirment or instruction of E-I-C. a) Type - II(100 mm thickness) inter locking system 100 mm Paver Block |
| 4 | Excavation for StructuresEarth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work (Reference to MoRT&H's specification clause 304).(i) Ordinary soilA) Manual Means (Depth upto 3 m) |
| 5 | Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200).F) PCC Grade M30I) Using Concrete Mixer |
| 6 | Prime CoatProviding and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502).i) On WMM/WBM surface @ 0.85kg /sqm. Using Cationic SS-1 |
| 7 | Tack CoatProviding and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).ii) On Granular surface treated with primer @ 0.275 /sqm. Using Cationic RS |
| 8 | Tack CoatProviding and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).i) On bituminous surface @ 0.25kg /sqm Using Cationic RS |
| 9 | Repairing Pot-holes with Bituminous Macadam (Grading - II, for compacted thickness of upto 75mm)Filling Pot Holes with Bituminous Macadam using Mobile Hot Mix plant (6-10 TPH) with approved crushed aggregates of specified gradingpremixed with bituminous binder @3.4% by wt. of the total mix, transported to site and laid in the pot hole prepared before hand by cutting the edges to get a firm vertical face and by removing all the failed and loose materials including dust and applying tack coat evenly on the sides and on the surface as per specification, rolling the filled depression with 8-10 tonne smooth wheeled roller to achieve the desired compaction, including the cost and carriage of stone aggregates and bitumen, hire charges of machinery and equipment, cost of fuel and lubricants and wages of all operational staff, quality control except the cost of tack coat complete as per direction of Engineer-in-charge. Payment to be made on the basis of the loose net volume of the stone aggregates used in the work. |
| 10 | Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510). Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour |
| 11 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type B seal coats (Reference to MORT&H's specification clause 511) 12(i) suitable approved grade. Providing and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 12 | GST (Sl-01 to Sl-10) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysSep 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender