Tender For Special Repair To Md Accn P/O/21 At Chindit Top Of Age B/R Under Ge Tenga
Tender Value
38.80 Lakhs
Estimated cost
Bid Submission
22 Sep 2026
6 days left
EMD
77600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kameng → Arunachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Md Accn P/O/21 At Chindit Top Of Age B/R Under Ge Tenga
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in roofs, floors, beams, staircases, landing and similar works (other than ground floor) etc complete. |
| 2 | M&L for 40 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in roof pad, floorings, including finishing the surface . |
| 3 | Material and labour for taking down of existing tarfelt and bituminous compounds in roof of any description from roof or terracing, roughening surfaces of old concrete surface by picking u,sweeping clean and washing down with water to remove dust etc providing 15mm thick screed bed or bed or bedding layer of cement mortar (1:4) for laying waterproofing membrane and finishing surface even and smooth without using extra cement and providing waterproofing treatment over smooth finished surfaces after applying one coat of cold bituminous primer at 0.30 ltrs / Sqm ,hot bitumen 85/25 @ 1.2 kgs /Sqm providing laying APP polymer, modified , non-woven polyster mat,reinforced membrane, 3mm thick (min) weighing 3.50 Kg/Sqm with surface finish of white mineral ,by torch application method , with minimum 75mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying one coat of bituminous based solar reflective aluminium paint @ 100Gms /Sqm over APP modified membrane all as specified and directed. |
| 4 | M&L for Sunken Treatment of Toilet Bathroom(including Demolition as in following steps: i)Top of RCC slab in sunken portion including peripheral beams shall be plastered with 15mm thick in CM 1:3 using approved water proofing compound @ 3% by weight of cement finished even & smooth using extra cement ,curved at the junctions. ii)Apply two coat of epoxy resin/polymer modified cementations coating like a brush bond of FOSROK/SIKA/Pedilite or equivalent, both on floor & beams. iii)Sunken slabs to be given 1:20 slope outword 25mm GI pipe spout with 300mm projection beyond outer surface of wall shall be provided. iv)Water tightness of sunken portion to be tested by ponding with water for 72 hours.In case of even a slight mark of seepage,the portion to be treated and ponding shall be carried out again to confirm the water tightness of sunken slab. v)The sunken portion will be filled with lean concrete 1:4:8 type D-2 using brick agg to req depth. Note:No cutting in roof slab/beam shall be allowed for passing of CI pipes & fittings.The stage of water proofing to sunken slab shall be passed by Eng-in-charge/GE. |
| 5 | Supply only integral water proofing compound. |
| 6 | M&L for 20 mm thick screed bed in CM 1:6 for laying floor finish. |
| 7 | M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 8 | M&L for Kota stone slab 20-25mm thick space in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 9 | M&L Chequered cement concrete tiles 20cmx20cmx25mm thick with greycement and pigment, set jointed and pointed in neat cement slurry in floors. |
| 10 | M&L for Providing, cement concrete type B1 (1:2:4) using 20 mm graded aggregate in roof kerbs or mud stops, rounded or chamfered on edges |
| 11 | Demolition of cement concrete in ground floor and paving not exc 15 cm thick (below or above groud). |
| 12 | M & L 75 mm thick Cement concrete type D2,1:4:8 (40mm graded aggregate) as in sub base, including form work complete as as specified and directed by Engineer-in-Charge |
| 13 | M&L for 25 mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in floorings, as in sub base of floor tiles in ground floor.complete all as specified |
| 14 | M&L for 15mm thick screed bed in CM 1:4 for laying floor tiles. |
| 15 | M&L for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm,in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. |
| 16 | M&L for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding .38 sqm,in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. |
| 17 | M&L for 10mm thick rendering in CM 1:4 finish even and fair for laying wall tiles. |
| 18 | M & L for 450 x 350 x 07 mm thick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. |
| 19 | M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection surface finished even and smooth using with extra cement |
| 20 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for |
| 21 | M&L for cement concrete 25mm thick type B-0(1:2:4)12.5 mm graded aggregate ,finish cement concrete surface even and smooth using extra cement. |
| 22 | M&L for 20 mm thick granite work (table rubbed and polished) in steps and cooking platform and like in cm (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble of any shade |
| 23 | Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for. |
| 24 | M & L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips. |
| 25 | M & L for Mild steel TMT bars 8 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips. |
| 26 | M&L for form work to chullah hoods,chajjas,troughs and similar items including edges with fair finish flat surfaces |
| 27 | M&L for Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 05cm but n exc 10cm wide with fair finish flat surfaces |
| 28 | M&L for reinforced cement concrete ratio(1:1.5:3) (using 20 mm graded stone aggregate) for slabs supported on walls , beams and columns, in floors ,roofs, landings and in shelves ,chhajjas and the like complete with all necessary formwork etc all as specified and as directed. |
| 29 | Demolition of precast cement concrete articles and precast concrete block walling built in cement mortar |
| 30 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete. |
| 31 | M&L for precast cement concrete 1:3:6 type C1 using 20 mm graded aggregate block solid building blocks or slabs in not exc 10cm thick (with plain or interlocking joints as directed ) complete set in CM 1:4 all as specified and directed. |
| 32 | M & L 15 mm thick rendering in cement mortar 1:4 on brick or concrete surfaces finished even & smooth without using extra cement |
| 33 | Taking down cement plaster on brick, concrete stone surfaces etc including raking out joints, hacking for key, scrubbing down with water etc. |
| 34 | M & L 15 mm thick rendering in cement mortar 1:6 on brick or concrete surfaces finished even & smooth without using extra cement all as specified and directed. |
| 35 | Material and labour for 5 mm thick rendering in cement mortar (1:3) on brick or concrete surfaces of ceiling finshed even and smooth without using extra cement. |
| 36 | M & L for 20 mm thick plaster in cement mortar 1:4 on brick or concrete surfaces using WPC @ 3% by weight of cement finishing the surfaces even &smooth without using extra cement.(WPC will be measured and paid separately) |
| 37 | M & L for PCC 1:2:4 type B-1 using 20mm grade stone aggregate as in coping & Drain. |
| 38 | M&L PCC in surface channels and drains type B2 (1:2:4) using 40 mm graded stone aggregate all as specified and directed. |
| 39 | Supply only integral water proofing compound. |
| 40 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc. |
| 41 | M&L for pre cast re-inforced cement concrete 1:2:4 type B-1 as in cover slab for man hole and similar article with plain face set in Set in CM 1:4. |
| 42 | Dismantling of CI soil, rain water pipes, cast and vent pipes of any dia, any pattern including all fittings. |
| 43 | S&F PVC (SWR) pipes single socketed 110 mm bore in any length with rubber ring joints fixed to walls |
| 44 | S&F PVC (SWR) pipes single socketed 75 mm bore in any length with rubber ring joints fixed to walls |
| 45 | S&F PVC (SWR) junction single, (single T) equal or unequal with access door 110mm bore. |
| 46 | S&F PVC (SWR) bends any radius, 110mm bore |
| 47 | S&F PVC (SWR) bends any radius, 75 mm bore |
| 48 | S&F PVC (SWR) junction single, (single T) equal or unequal with access door 75mm bore. |
| 49 | S & F 125 MM PVC (SWR) 'p' trap |
| 50 | S&F PVC (SWR) vent cowl 110 mm bore |
| 51 | S&F PVC (SWR) couplers 110mm bore. |
| 52 | S&F PVC (SWR) WC connector 110mm bore lip ring. |
| 53 | S&F PVC (SWR) floor trap, 75mm dia outlet, plain with grating incl jointing with solvent cement. |
| 54 | Dismantling of water tanks exc 250 ltrs & n. exc 500 ltrs capacity and removing to store. |
| 55 | S & F PVC water storage tanks of 1000 ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position all as specified |
| 56 | S & F in repairs ball brass valves, high pressure, with polyethene float and flynut complete screwed for iron pipe of 20mm dia all as specified |
| 57 | Taking up or down 15 mm bore steel water tubing and connections including clfor refixing or removal to store |
| 58 | S&F 15mm bore steel water tubes, medium grade, galvanised with all fittings and fixed complete to walls/ceilings or laid in trenches. |
| 59 | Refixing 15 mm bore old steel tubing and conncetions in new or old position to walls and ceiling with new fittings coplete all as directed |
| 60 | Taking up or down 20 mm bore steel water tubing and connections including cleaning or refixing or removal to store |
| 61 | S&F 20 mm bore steel water tubes, medium grade, galvanised with all fittings and fixed complete to walls/ceilings or laid in trenches. |
| 62 | Refixing 20 mm bore old steel tubing and conncetions in new or old position to walls and ceiling with new fittings coplete all as directed |
| 63 | S & F in repair looking mirror 600 mm x 450 mm bevelled edge mirror or selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 64 | S&F in repairs vitreous china wash hand basin white pedstral petern of size 550mmx400 mm including cutting for and pinning in end of brackets,32 mm waste fittings,brass chromium plated for glazed ware sinks,basins etc.with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed.and flush pipe of polytethylene of low or high density or PVC 32 mm dia complete all as specified & directed |
| 65 | S&F PVC connections 15 mm size with PTMT nuts of length 450 mm. |
| 66 | S&F in repairs Brass CP sink mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed. |
| 67 | S&F in repairs Brass CP wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed. |
| 68 | S&F in repairs Brass CP basin mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed. |
| 69 | Supply and fixing in repair vitreous China squatting pan, \\"Orissa\\" pattern size 580 X 440 mm, white, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and complete |
| 70 | S & F in repairs 10 ltrs capacity Vitreous China valveless, syphonic action type, but flushing cistern of dual pressed steel, enamelled white , low level, with inlet, ball valve, float and handle including brackets complete as specified. |
| 71 | S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe |
| 72 | S&F in repair 15 mm dia stop valve external threaded,cast coppper alloy ,screwed down high pressure with crutch or butterfly handle ,screwed both ends for iron pipe or for uninos . |
| 73 | S & F in repairs 15mm dia bib tap, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specifed. |
| 74 | S & F in repair brass chromium plated shower rose 125 mm dia with swivel joints including fixing to steel pipe or union. |
| 75 | S&F stainless sink made of stainless steel 1.00 mm thick kitchen with plug washers, wastes;including bedding in cement mortor on dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 x 420 mm with bowl size 410 x 330 x 160mm, complete. |
| 76 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exc 4 Sqm. |
| 77 | S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying and fixing in opening as per specification and drawing. |
| 78 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat mouleded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rain, lock & bottom rail on either side & as gap insert for top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supling & fixing in the frame at site as per specification & drawing. |
| 79 | S & F 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete |
| 80 | S & F 25 mm thick flush sutter ,solid core construction, with block board core and plywood face panels,commercial type on both sides |
| 81 | M & L for 12 mm thick ply wood, grade BWR, type BB, fixed with nails to timber frame work on wall surfaces. |
| 82 | S&F 12 mm thick prelaminated particle board,interior grade, prelaminated one side with decorative choice lamination, and other side balancing white lamanation, fixed with screw to timber frame work. |
| 83 | M&L for preparation of new wooden surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. |
| 84 | S&F 40mm dia, cupboard knobs fixed with not, screw and washer |
| 85 | S & F 2nd class hard wood plain framed factory made panelled shutter 35mm thick (any number of panels) with panels of timber flat on both sides, feather edged or of veneered particle board medium density, wood particle board with commercial face veneer . |
| 86 | S & F 30mm thick 2nd class hard wood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads etc |
| 87 | S & F 100mm size mild steel butt hinges medium weight cold rolled and fixed. |
| 88 | S & F 75mm size mild steel butt hinges medium weight cold rolled and fixed. |
| 89 | S/F 150 mm long aluminium anodised barrel tower bolts of extruded section. |
| 90 | S/F 75 mm long aluminium anodised barrel tower bolts of extruded section. |
| 91 | S/F 150 mm long aluminium handles cast type anodised. |
| 92 | S/F 75 mm long aluminium handles cast type anodised. |
| 93 | S & F in repair aluminium alloy, anodised, sliding door bolts 300mm size with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed |
| 94 | S&F aluminium alloy, anodised floor door stopper ,tongue anodized 140mm length including vulcanised rubber piece with hard drawn steel spring,fixed in floors complete all as specified. |
| 95 | S&F PVC coated 25mm dia mild steel chromium plated curtain rod of medium weight and including fixing brackets, finals and decorative end supports etc complete all as directed” |
| 96 | Material and labour for preparation of old surface of wood and wood based materials over 10 Cm width or girth and applying one coat of synthetic enamel paint as directed and specified. |
| 97 | M & L for applying one coat of synthetic enamel paint to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of old steel surfaces. |
| 98 | M&L for Two coats of distemper oil emulsion (OBD) on new plastered wall surfaces of any description over a coat of alkali resistent priming paint over a coat of plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth.all as specified including preperation of surfaces all as specified and directed. |
| 99 | M&L for one coats of distemper oil emulsion (OBD) on old plastered wall surfaces incl prepration of old surface over a coat of plaster of paris putty 1 mm of any description all as specified and directed. |
| 100 | M&L for Two coats of white wash on new surfaces of ceiling incl preparation of surface complete all as specified. |
| 101 | Material & Labour for applying Two or more coats on new surface of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including preparation of new surface over a coat of plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth as specified. |
| 102 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV r on old surface esistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces including preparation of old surface over a coat of plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth as specified. |
| 103 | M&L for Preparing old plastered surfaces of ceiling and applying one coat of white wash complete all as specified. |
| 104 | S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) |
| 105 | S&F in repairs soap dish, any type, fiexd to plugs with chromium plated brass screws |
| 106 | S&F CP towel rail 450mm long , fixed with chromium plated brass screws |
| 107 | S&F in repair bathroom 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercialplywood and fixed to wooden plugs with chromium plated brass screws and cup washers completed all as directed. |
| 108 | S & F in repairs sheet glass corner shelf assembly complete all as specified and as directed. |
| 109 | S & F in repairs Kitchen/Room cabinet with 12mm thick Prelaminated particle board, interior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work completed as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysSep 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender