Bids Are invited for Dsp Based Induction Motor Control Trainer Setup

Sharing tender

Bids Are invited for Dsp Based Induction Motor Control Trainer Setup Analog To Digital Signal Converter Using Ads8686s - An Analog-To-Digital Signal Converter Evaluation Platform Featuring A 16-Channel, 16-Bit, Simultaneous-S Ling Sar Adc Supporting Multiple Input Ranges (Pm10v, Pm5v, Or Pm2.5V). It Includes A Precision Host Interface (Phi) Controller Board For Usb Communication, Data Capture, And Digital Power, Along With Onboard Input Filtering, An Ultralow-Noise Ldo Regulator, And Selectable Voltage Reference Options. , C2000 Development Board - Tms320f28379d - A Standardized Development Tool Built Around A Dual 200 Mhz C28x Cpu With Dual Clas, 1 Mb Flash, And Extensive Control Peripherals. It Features An Isolated Xds100v2 Jtag Debug Probe, Support For Up To Two Plug-In Daughter Boards, Dual Encoder Interface Connectors, And Isolated Can Transceiver Support, Making It Position-Manager Ready For Absolute Encoders, Resolvers, And Sincos Transducers. , C2000 Development Board - Tms320f28p650 - A Prototyping Development Board For The Ti C2000 F28p65x Real-Time Microcontroller Series, Equipped With A 200 Mhz Dual C28x Cpu With Fpu/Tmu And 1.28 Mb Flash. The Platform Includes An Onboard Xds110 Debug Probe, Power Domain Isolation, Cross-Compatibility With Two Daughter Board Modules, Onboard Can Transceivers, Eqep Encoder Connectors, And Integrated Ethercat Phys With Rj45 Ports. , Educational Practice Board For Tms320f28335 - A Comprehensive Training Platform Powered By A 150 Mhz 32-Bit Floating-Point Tms320f28335 Digital Signal Controller With 512 Kb Flash, 1 Mb Off-Chip Sram, And Matlab/Simulink Compatibility. It Incorporates Rich I/O Interfaces Including Pwm Outputs, Capture Inputs, Adc Connectors With Op- Protection, Can, Uart, Spi Dac, And Dip Switche And Comes Complete With A Workbook And S Le Code Packaged In A Wooden Box. , Usb Jtag Emulator For Epb28335 - Xds100_V2 - A Basic Usb 2.0 Debug Probe Providing Jtag Emulation For Texas Instruments Processors, Designed For Integration With Code Composer Studio (V5). It Features 1.8 V And 3.3 V Target I/O Voltage Support, Real-Time Debugging Capabilities, Target Power-Loss Detection, And Adaptive Clocking To Interface With The Epb28335 Development Board. , Usb Jtag Emulator For Epb28335 - Xds200 - A Midrange Debug Probe Supporting Ieee 1149.1 Jtag, Cjtag, And Swd/Swo Protocols Across A Wide 1.5V To 4.1V Target Voltage Range. Connected Via High-Speed Usb 2.0 (Or Optional Ethernet), It Delivers Real-Time Debugging, Hardware Breakpoints, Etb-Based Core/System Tracing, And Target Power/Reset Management Across An Extensive Range Of Ti Processors, Mcus, And Dsps. , Usb Jtag Emulator For Epb28335 - Xds560v2 - A High-Performance Debug Probe For Ti Processors Supporting Jtag And 2-Pin Cjtag With Target Levels From 1.2V To 4.1V. Fully Integrated With Code Composer Studio, It Offers High-Speed Usb 2.0 Communication Alongside Comprehensive Hardware Debugging And Advanced Trace Capabilities Across A Wide Array Of Ti Microcontroller, Dsp, And Automotive Soc Families. , Pwm Isolator Module With Smps Power Supply - A Pluggable Interface Module That Converts +5V Dc Logic Pwm Signals From A Dsp Board Into 12 Channels Of Fully Isolated And Lified +15V Dc Outputs For Driving Power Modules. Powered By A +9V To +36V Dc Input, It Features Integrated Thermal Trip Handling, Inverter Fault-Signal Feedback, Onboard Status Leds, And Test Points, All Safely Housed In A Wooden Box. , 3-Phase 1 Hp Inverter Stack Module - A Forced-Air-Cooled Power Module Combining A 3-Phase Diode Rectifier And An Igbt Inverter Stack Rated Up To 30A Max At 2Khz Or 10A At 20Khz. It Features Gate Drivers With Short-Circuit And Undervoltage Protection, A 3,Mus Interlocking Time, An Integrated Dc/Snubber Capacitor Assembly, Heat Sink Thermal Protection, And Direct Banana-Cable/Pwm Connections For Motor Drive Experiments. , Induction Motor Coupled With Encoder - A 1 Hp, 3-Phase, 4-Pole Induction Motor Rated For 1500 Rpm Operation. It Comes With An Internal, Direct-Coupled +5V Quadrature Encoder Providing 1024 Ppr Resolution To Supply Precise Speed And Position Feedback For Closed-Loop Motor Control Development. , Dc Generator With Load Panel - An Electro-Mechanical Load Testing System Comprising A Single-Phase 1 Hp, 1500 Rpm Dc Generator Mechanically Coupled To The Induction Motor. It Includes An Accompanying 230V Ac Load Panel Equipped With Switchable Resistive Loads (25W To 200W) And Digital Dc Volt/ Meters To Apply Controlled Electrical Loads To The Drive Assembly. , Sensor Interfacing Kit - 28335 With 3 Current Sensor - A Signal Conditioning Interface Housing Three La 25 Np Current Sensors Configured To Measure Inverter Ac/Dc Phase Currents. It Steps Down And Shifts Current Signals Into A 0V To 3V Range Suitable For Dsp Adc Inputs, While Providing Power Rails, Status Leds, Flexible Offset Adjustments Via Potentiometers, And A Dedicated Db9 Connector To Pass Motor Encoder Signals To The Control Unit. , Sensor Interfacing Kit - 28335 With 3 Voltage Sensor - A Complementary Signal Conditioning Kit Containing Three Lv 25 P Voltage Sensors Rated For 10V To 500V Measurement. It Conditions Ac/Dc Voltages Down To A 0V To 3V Scale For Dsp Processing With Adjustable Dc Offset Controls, And Includes Encoder Passthrough Capabilities. It Is Supplied Together With The Current Sensing Kit Inside A Unified Metal Panel Enclosure.