Tender For Construction Of School And Hostel Building Of Ratan Mani Seva Mission At South Dhumacherra, Dhalai District, Tripura/ Sh: Construction Of Gf With Foundation Provision Of (G+1) / Building Portion Including Internal Water Supply, Sanitary In
Tender Value
3.81 Crore
Estimated cost
Bid Submission
15 Sep 2026
3 days left
EMD
7.63 Lakhs
Bank guarantee accepted
Document Fee
8000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhalai → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of School And Hostel Building Of Ratan Mani Seva Mission At South Dhumacherra, Dhalai District, Tripura/ Sh: Construction Of Gf With Foundation Provision Of (G+1) / Building Portion Including Internal Water Supply, Sanitary Installation, Sewage & Drainage, Sbdtw.
BOQ
| Sl. No. | Item Description |
| 1 | SUB-HEAD : EARTH WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. |
| 3 | All kinds of soil |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 5 | All kinds of soil |
| 6 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 7 | All kinds of soil |
| 8 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 9 | Supplying chemical emulsion in sealed containers including delivery as specified. |
| 10 | Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 11 | Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion):Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete: |
| 12 | With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 13 | Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: |
| 14 | With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 15 | SUB-HEAD : CEMENT CONCRETE WORK |
| 16 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - |
| 17 | All work upto plinth level: |
| 18 | a) 1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size) |
| 19 | b) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 40 mm nominal size). |
| 20 | c) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded brick aggregate 20 mm nominal size) |
| 21 | Providing and laying cement concrete in retaining walls, return walls (any thick-ness) including attached pilasters, columns, piers, abutmets, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc. upto floor five level, excluding the cost of centring shuttering and finishing a) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) |
| 22 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 23 | a)Foundations, footings, bases for columns. |
| 24 | (b) Columns, piers, abutments, pillaras, posts and struts |
| 25 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 26 | SUB-HEAD : RCC WORK |
| 27 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement-All work upto plinth level:1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 28 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 29 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size). |
| 30 | Providing and laying upto floor five level reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers facias and eaves boards excluding the cost of centring, shuttering, finishing and reinforcement-a)1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size). |
| 31 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level / above plinth level:- Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 32 | Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits.a) 40 mm thick |
| 33 | Centering shuttering including struttings, propping etc.and removal of form work for:a) Foundations, footings, bases for columns etc. for mass concrete with timber plank. |
| 34 | b) Suspended floors, roofs, landings, balconies and access platform with shuttering ply |
| 35 | c) Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply |
| 36 | d) Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 37 | e) Stairs (excluding landings) except spiral-staircases with wooden plank |
| 38 | f) Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards. |
| 39 | g) Edges of slabs and breaks in floors and walls under 20 cm. Wide |
| 40 | h) Weather shade, chajjas, corbels etc. including edges |
| 41 | i) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply. |
| 42 | SUB-HEAD : BRICK WORK |
| 43 | First class brick work in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 44 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-a)In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 45 | Extra for brick masonry work in triangular, square and rectangular pillars including cost of all materials as required complete. |
| 46 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 47 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 48 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 49 | SUB-HEAD : WOOD WORK |
| 50 | Providing and fixing T-iron frames for doors, windowsand ventilators of mild steel Tee-sections, joints mitredand welded, including fixing of necessary butt hingesand screws and applying a priming coat of approved steel imer:- (a) Fixing with 15x3 mm lugs 10 cm long embedded in cementconcrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 51 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framedand fixed in position : (a) Local Teak Wood |
| 52 | Providing and fixing 25 mm thick shutters for cupboards etc. including ISl marked black enamelled M.S. butt hinges with necessary screws : (a) Panelled or panelled and glazed shutters:- (i) Gamair Wood. |
| 53 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters:- (i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 54 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete:- (a) Fixed to openings /wooden frames with rawl plugs screws etc. |
| 55 | Providing 40 × 5 mm flat iron hold fast 40 cm longincluding fixing to frame with 10 mm diameter bolts,nuts and wooden plugs and embedding in cementconcrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement :3 fine sand : 6 graded stone aggregate 20mmnominal size) |
| 56 | Providing and fixing IS : 1341 marked M.S. heavy weight butt hinges with necessary screws etc. complete : |
| 57 | 125 × 90 × 4.00 mm |
| 58 | 75 × 60 × 3.10 mm |
| 59 | Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers including necessary screws etc. complete (best make of approved quality): |
| 60 | Providing and fixing 50 mm bright finished brass cup board or wardrobe knob with necessary screws (best make of approved quality) |
| 61 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 62 | 300x16 mm |
| 63 | 250x16 mm |
| 64 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 65 | 300x16 mm |
| 66 | 250x16 mm |
| 67 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 68 | 125mm |
| 69 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. |
| 70 | Single rubber stopper |
| 71 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 72 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 73 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 74 | Providing 50 × 50 × 50 mm Gamair wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement: 3 fine sand) and making good the walls etc. |
| 75 | Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 76 | Extra for additional labour for circular works, such as in frames of fan light: Local teak wood. |
| 77 | SUB-HEAD : STEEL WORK |
| 78 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required. |
| 79 | Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete. |
| 80 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required:- |
| 81 | G.I.pipes. (40mm Dia) |
| 82 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 83 | SUB-HEAD : ALUMINIUM WORK |
| 84 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-a) For fixed portion of approved quality:- |
| 85 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 86 | b) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 87 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 88 | Providing and fixing stainless steel (SS 304 grade) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:-a) 205 x 19 mm |
| 89 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:- |
| 90 | Anodised aluminium of grade AC 15 ). |
| 91 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge :-A) Prelaminated particle board of approved quality with decorative lamination on one side and balancing lamination on other side. |
| 92 | SUB-HEAD : FLOORING AND SKIRTING WORK |
| 93 | Providing and fixing Marble stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishing complete.a) 18 mm thick Marble stone i) Raj Nagar plain marble |
| 94 | Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 fine sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. 8mm thick Rajnagar marble tiles (polished) |
| 95 | Providing and fixing precast chequered terrazo tiles 22mm thick with graded marble chips of size upto 6 mm,laid on floors, footpath & courtyard on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete.Dark shade pigment using ordinary cement |
| 96 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles:300 mm x 300 mm in all shades and designs |
| 97 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge. a) Double charged Stainfree vitrified tiles (Glossy):-i) Size of tile 60x60 cm. |
| 98 | b) Double charged Stainfree vitrified tiles (Glossy):- (i) Size of tile 60x60 cm. |
| 99 | Providing and fixing 1st quality ceramic glazed wall tiles (minimum 200 x 300) conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete:-450 mm X 300 mm in all shades and design |
| 100 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622- 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge..10.42.4 Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid):- Size of tile 600 mm x 600 mm. |
| 101 | Cement concrete flooring 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.A) 25 mm thick with 12.5 mm well burnt brick aggregate. |
| 102 | Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge:- Kota stone slab 25mm thick. |
| 103 | Providing and fixing precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning complete as per direction of Engineer -in - charge:-In dark shade using ordinary cement |
| 104 | SUB-HEAD : ROOFING AND CEILING WORK |
| 105 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.a) Hot finished welded type tubes |
| 106 | Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required:- a) 0.40mm thickness. |
| 107 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single socketed pipe - 110 mm OD. |
| 108 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with : a)Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size). |
| 109 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. |
| 110 | SUB-HEAD : FINISHING WORK |
| 111 | 12 mm cement plaster of mixIn cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 112 | b) 12 mm cement plaster of mix:- In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 113 | 15 mm cement plaster on the rough side of single or half brick wall of mix:In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 114 | b) 15 mm cement plaster on the rough side of single or half brick wall of mix:In cement mortar 1:6 ( 1 cement :6 fine sand ). |
| 115 | 6 mm cement plaster of mixIn cement mortar 1:3 ( 1 cement : 3 fine sand ). |
| 116 | Neat cement punning. |
| 117 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :-New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 118 | Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : New work ( two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 119 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture. |
| 120 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 121 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : |
| 122 | With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 123 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture. |
| 124 | SUB-HEAD : SANITARY WORKS |
| 125 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :a)White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 126 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :a)W.C. pan with ISI marked white solid plastic seat and lid |
| 127 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and x410x265mm sizes respectively |
| 128 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings: |
| 129 | Flat back wash basin of size 550x400mm. |
| 130 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings completeA)Flexible pipei)32 mm dia |
| 131 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 132 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 133 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 134 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 135 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms. |
| 136 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board:- (i) 510x1040 mm bowl depth 250mm. |
| 137 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: (a)Single socketed pipe - 110 mm OD. |
| 138 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: |
| 139 | (i) Coupler - 110mm |
| 140 | (ii) Single pushfit Coupler - 110mm |
| 141 | (iii) Single equal tee without door - 110 x 110 x 110 mm |
| 142 | (iv) Single equal tee with door - 110 x 110 x 110 mm |
| 143 | (vii) Bend 87.5o - 110mm |
| 144 | (viii) Plain shoe - 110 mm |
| 145 | (v) Double equal junction of required degree without door - 110 x 110 x 110 mm |
| 146 | (vi) Double equal junction of required degree with door - 110 x 110 x 110 mm |
| 147 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water, soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete:- (a) 110mm. |
| 148 | Providing and Fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required :a) Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. |
| 149 | Providing and Fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. Automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required :a) Single squatting plate with 5 litre P.V.C. automatic flushing cistern. |
| 150 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : (a) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps. |
| 151 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board;- i) 610x510 mm bowl depth 200 mm. |
| 152 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete:- (a) Flexible pipe: (i) 32 mm dia. |
| 153 | Providing and fixing to the inlet mouth of rain water, soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm:-(a) 100mm. |
| 154 | SUB-HEAD : WATER SUPPLY |
| 155 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I. fittings and clamps, including cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in charge. Internal work - Exposed on wall. |
| 156 | 15 mm nominal bore |
| 157 | 20 mm nominal bore |
| 158 | 25 mm nominal bore |
| 159 | 40 mm nominal bore |
| 160 | Making connection of G.I. distribution branch with G.I. main following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete as per CPWD specification and direction of the Engineer - in - charge. |
| 161 | 25 to 40 mm nominal bore |
| 162 | Providing and fixing brass bib cock of approved quality : |
| 163 | 15 mm nominal bore |
| 164 | Providing and fixing brass stop cock of approved quality : |
| 165 | 15 mm nominal bore |
| 166 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): |
| 167 | 25 mm nominal bore |
| 168 | 40 mm nominal bore |
| 169 | Providing and fixing gun metal non-return valve of approved quality (screwed end): |
| 170 | 25 mm nominal bore |
| 171 | Vertical |
| 172 | 40 mm nominal boreVertical |
| 173 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 174 | Constructing masonry Chamber 30x30x50 cm, inside , in brick work in cement mortar 1:4 (1 cement :4 fine sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design : |
| 175 | With Second Class bricks |
| 176 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : |
| 177 | 15 mm diameter pipe |
| 178 | 20 mm diameter pipe |
| 179 | 25 mm diameter pipe |
| 180 | 40 mm diameter pipe |
| 181 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : |
| 182 | 15 mm diameter pipe |
| 183 | 20 mm diameter pipe |
| 184 | 40 mm diameter pipe |
| 185 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete as per CPWD specification and direction of the Engineer - in - charge.(New work) |
| 186 | 20 mm nominal bore |
| 187 | 25 mm diameter pipe |
| 188 | 32 mm diameter pipe |
| 189 | 40 mm diameter pipe |
| 190 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I. fittings including trenching and refilling etc. complete as per CPWD specification and direction of the Engineer - in - charge:- External work:- |
| 191 | (a) 40 mm nominal bore. |
| 192 | (b) 50 mm nominal bore. |
| 193 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):- (a) 32 mm nominal bore. |
| 194 | Providing and fixing gun metal non-return valve of approved quality (screwed end): (a) 32 mm nominal bore.:- Vertical |
| 195 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete :- (a) 25 mm nominal bore. |
| 196 | Providing and fixing uplasticised PVC connection pipe with brass unions :-(a) 45 cm length:- (i) 15 mm nominal bore. |
| 197 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms:-(i) 15 mm nominal bore. |
| 198 | Providing and fixing PTMT grating of approved quality and colour:- (a) Circular type.i) 100 mm nominal dia. |
| 199 | Cutting holes upto 30x30 cm in walls including making good the same :i) With 1st class bricks. |
| 200 | Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof. |
| 201 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 202 | SUB HEAD : SEWAGE AND DRAINAGE WORKS |
| 203 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 6 kg / cm2)conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion: |
| 204 | Single socketed pipe - 110 mm OD |
| 205 | Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design:i) 100 mm diameter S.W. Pipe |
| 206 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 207 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : |
| 208 | ii) Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 209 | Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design :- |
| 210 | i) For 500x700 mm size. |
| 211 | ii) For 455 x 610 mm size. |
| 212 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : i) Inside dimensions 455x610 mm and 45 cm deep for single pipe line. |
| 213 | ii) Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 214 | Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) upto haunches of S.W. pipes including bed concrete as per standard design : i) 100 mm diameter S.W. Pipe |
| 215 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 216 | SUB HEAD : SBDTW |
| 217 | Drilling and boring pilot hole in any soil strata by manual means, collection of soil samples of different strata met with during drilling at variuse suitable levels, preservation of samples in polythene bags/ sample box and disposal of excess soil or mud, including the cost of water etc, as required to mantain the pilot hole properly as per specification and direction of the Engineer-in charge. |
| 218 | i) 100mm dia |
| 219 | Reaming of pilot hole to an enlarged bore hole in any soil strata by manual means, disposal of excess soil or mud, including the cost of water etc, as required to mantain the pilot hole properly as per specification and direction of the Engineer-in charge:- (i) From 100mm dia pilot hole to 250mm bore hole. |
| 220 | Providing and lowering of PVC pipe of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer-in-charge. |
| 221 | A) CM Casing pipe (UPVC) |
| 222 | i) 150mm dia |
| 223 | ii) 100mm dia |
| 224 | B) RS pipe |
| 225 | i) 100mm dia |
| 226 | Washing and development of tube well by using hand pump or by any suitable method and testing of the well as per specification and direction of the Engineer in charge. |
| 227 | Providing and shrouding of the deep tube well assembly with washed pea gravels (2.0 - 4.75 mm effective size) as per specification (IS: 4097) and direction of the Engineer in charge:- (A) With contractor rig:- (i) with pea gravels obtained from Durgapur, West Bengal. |
| 228 | Providing and fixing of UPVC end cap/ well cap suitable for UPVC 'CM' casing or 'CS' casing or RS pipe as per specification and direction of the Engineer in charge:-( i) 100mm dia. |
| 229 | Providing and fitting fixing GI pipe (Medium class) conforming to IS 1239 for column pipe assemble for instalation of submersible pump motor as per direction of Engineer in charge:- (i) 40mm NB. |
| 230 | Providing and fitting fixing GI bend/ elbow in the pipe line including testing of joints complete as per CPWD specification and direction of Engineer in charge.:- (i) 40mm NB. |
| 231 | Providing and fitting fixing of GI flange (10mm wall thickness) by welding with GI/ MS pipe as per placing position as per specification and the direction of Engineer in charge:- (i) 50mm dia. |
| 232 | Providing and fitting fixing of C.I. non return valve of approved quality as per CPWD pecification and the direction of Engineer in charge:- (i) 50mm nominal bore. |
| 233 | Providing and fitting fixingof 6feet x 4feet x1 inch (thickness)gamai wood/ plywood/plypanel board for fitting fixing of electric items in/c 2no's MS angle post (size 2 inch x 2inch x 9feet) nut & bolts for irrection of the same by 1:1.5:3 cement concrete casting (1 feet x 1feet x 2 feet) below the ground level and painting two or more coats & plastic paint as per specification and the direction of Engineer in charge. |
| 234 | Installation of submerssible pump and suitable motor upto requirede depth with GI column pipe in/c providing fitting fixing by necessaqry rubber washer , nuts & bolts, Ms safety clamp etc. As per required size and making necessary electrical connection with main switch/starter with motor in/c commissioning & trial run as per direction of the Engineerin charge (pump, motor with cable, GI Pipe will be issued by the Department at free of cost and fabrication of GI column pipe will be paid separately):-(i) 2500 GPH capacity. |
| 235 | Providing, installation & commissioning 2 HP submerssiblepump as per manufacturer's specification and direction of Engineer in charge complete. |
| 236 | Providing and fixing of UPVC reducer suitable for UPVC 'CM' casing or 'CS' casing or RS pipe as per specification and direction of the Engineer in charge.:- |
| 237 | i) 150 x 100mm dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysSep 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender