Tender For The Installation Of An Aluminium Partition In The Hall Of Residence No. 103/1B At Vidhayak Niwas-1, Replacement Of A Window Frame, And Other Necessary Civil Works.
Tender Value
50000
Estimated cost
Bid Submission
05 Sep 2026
4 days left
EMD
5000
Bank guarantee accepted
Document Fee
650
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Lucknow → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For The Installation Of An Aluminium Partition In The Hall Of Residence No. 103/1B At Vidhayak Niwas-1, Replacement Of A Window Frame, And Other Necessary Civil Works.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead. Of area 3 sq. metres and below(D.S.R No-15.12.1) |
| 2 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).salwood D.S.R No-9.1.2 |
| 3 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for hold fasts embedding hold fasts in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 ( 1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size). painting two coats of approved wood preservation to sides of chowkhats and making good the damages to wall and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge. Door chowkhats DSR No- 14.2.1 |
| 4 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws DSR 9.21.1 |
| 5 | Proding and fixing aluminium work for doors windows, ventilators and partitions with extruded built up standard tublar section/ appropriate Z section and other sections of approved make conferming to IS:733 and IS 1285 , fixing with dash fasteners of requried dia and size , including necessary filling up the gaps at at junction I.S at top bottom and sides with required EPDM rubber/ neoprene gasket etc alumimium section shall be smooth , rust free straight , mitred and joints machanically where requried including clear angle , aluminum snap beading for glazing / paneling C.P Brass/ stainless steel screws all complete as per architectural drawing and the direction of Engineer-in - charge (glazing, paneling , and dash fasteners to be paid for separately)::for shutters of doors, windows &ventilators including providing and fixing hinges/ pivots and making provision for fixings wherever required including the cost of EPDM rubber/ neoprene gasket required(fitting shall be paid for seprately):: powder coated aluminium ( minimum thickness of powder coating 50 micron (dsr -21.1.2.2) |
| 6 | Proding and fixing aluminium work for doors windows, ventilators and partitions with extruded built up standard tublar section/ appropriate Z section and other sections of approved make conferming to IS:733 and IS 1285 , fixing with dash fasteners of requried dia and size , including necessary filling up the gaps at at junction I.S at top bottom and sides with required EPDM rubber/ neoprene gasket etc alumimium section shall be smooth , rust free straight , mitred and joints machanically where requried including clear angle , aluminum snap beading for glazing / paneling C.P Brass/ stainless steel screws all complete as per architectural drawing and the direction of Engineer-in - charge (glazing, paneling , and dash fasteners to be paid for separately)::for shutters of doors, windows &ventilators including providing and fixing hinges/ pivots and making provision for fixings wherever required including the cost of EPDM rubber/ neoprene gasket required(fitting shall be paid for seprately):: powder coated aluminium ( minimum thickness of powder coating 50 micron (dsr -21.1.2.2) |
| 7 | Proding and fixing glazing in aluminium door , window ventilator shutter and partition etc with EPDM rubber / neoprane gasket etc complete as per architectural drawing and the direction of Engineer-in - charge (cost of aluminium snap beading shall be paid in basic item:(with float glass panes of 5 mm thickness (weight not less than 12.50kg/sqm)(dsr-21.3.2) |
| 8 | Providing and fixing of ACP (Alluminium Composite Pannel) sheet in Aluminium door/window, Ventilator shutter and Partitions etc, with EPDM Rubber/ neoprene gasket etc, complete as per the architectural drawings and the direction fo Engineer-in - charge (Cost of aluminium snap beading shall be paid in basic item. |
| 9 | FILLING the gap in between allmunium frame and adjacent RCC/Brick/stone work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete complying to ASTM C920, DIN 18540-F & ISO 11600. Upto 10mm depth and 10mm width item no. dsr- 21.19.2 |
| 10 | Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick &2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Anodized (AC 15 ) aluminium tubular handle bar dsr21.12.2 |
| 11 | P/F brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary citting and making good etc. complete.(D.S.R-21.13) |
| 12 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. DSR-1.1.18 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysSep 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender