Tender For Provision Of Certain B/R Work Services For Cr&Ss, Construction Of R And Certain Revenue Major Work At Afa Hyd.
Tender Value
45.41 Lakhs
Estimated cost
Bid Submission
21 Sep 2026
0 days left
EMD
90830
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Medchal Malkajgiri → Telangana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Certain B/R Work Services For Cr&Ss, Construction Of R And Certain Revenue Major Work At Afa Hyd.
BOQ
| Sl. No. | Item Description |
| 1 | M&L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engr-in-Charge |
| 2 | M&L Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed.by Engr-in-Charge. |
| 3 | M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area for complete all as specified and as directed.by Engr-in-Charge |
| 4 | M&L for 75mm thick PCC 1:4:8 type D2 using 40 mm graded agg as in sub base, complete all as specified and as directed.by Engr-in-Charge |
| 5 | S & F Glazed Vitrified coloured tiles 10 mm thick of any shade, polished area of each tile exc 0.42 sqm but not exc 1.00 Sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match in floors including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes and using spacer (3 to 4 mm ) and filling the gaps with coloured epoxy mortar complete all as specified and as directed by Engr-in-Charge |
| 6 | S & F Glazed Vitrified coloured tiles 10 mm thick of any shade, polished area of each tile exc 0.42 sqm but not exc 1.00 Sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match in skirting/dado/ vertical surafces,including rendering of mortar 10 mm thick in cement mortar 1:4 and using spacer (3 to 4 mm )and filling the gaps with coloured epoxy mortar complete all as specified and as directed by Engr-in-Charge |
| 7 | M& L for Pre-cast cement concrete block masonry with type PCC 1:3:6 mix type C-1 using 20 mm graded stone aggregate solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed. |
| 8 | ML for Machine cut kota stone slab flooring including laying of kota stone slab in floor, tread, riser, using kota stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 20 mm screed beb in cement mortar 1:6 complete all as specified and directed. |
| 9 | M&L for Precast reinforced cement concrete 1:2:4 mix, type B-1 using 20 mm graded stone aggregate as in slabs supported on walls, as in platforms, shelves etc all as specified and directed. |
| 10 | M&L for steel reinforcement TMT bars 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 11 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete flat complete all as specified and as directed. |
| 12 | M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed. |
| 13 | M&L for18 to 20 mm thick Granite/ Tan brown/ imperial brown/ steel grey/ ruby red/ pearl blue/ titanium black work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms or in floors laid over cement mortar screed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite inlcuding taking down plaster / screed any thickness. |
| 14 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 15 | S&F of Powder coated aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, rollers, rubber packing, anodised aluminium snap beading, screws, anodised aluminium locking plates and locking arrangement etc |
| 16 | S & F in repair 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with nails complete all as specified and directed |
| 17 | S&F Steel rolling shutters, with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indi cated, complete: push pull or manual typ all as specified and as directed. |
| 18 | S&F Safety lever locks mild steel with 4 levers for rolling shutters all as specified and as directed. |
| 19 | S&F Ball bearing for rolling shutters all as specified and as directed. |
| 20 | M & L for preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer etc complete. |
| 21 | S&F of 1.5 MM thick(wall Thickness) 25 mm dia stainless steel curtain rod including necessary fitting like(Wall clamp,end clamp ,finale etc) fited with screws, complete all specified and directed. |
| 22 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard / dense soil. |
| 23 | M&L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Hard/Dense Soil complete all as specified and directed. |
| 24 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 25 | Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 26 | M& L for Plain Cement concrete Type D2 1:4:8 (40 mm graded Aggregate) as in foundations, filling and mass concrete complete all as specified and as directed. |
| 27 | M&L for RCC nominal mix 1:1:2 in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns,walls Top layer of Ramp, basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. |
| 28 | M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exc 5cm but not exc.10cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed. |
| 29 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, all as specified and directed. |
| 30 | M&L for Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia for strrups and spacers etc all as specified and directed. |
| 31 | M&L for hardcore of gauge n exc. 63 mm of broken stone boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface. |
| 32 | M & L for Rendering 15 mm thick on fair faces of Block masonry surfaces / RCC surface or surface other than fair face of brick-work or on one side of lathing in CM 1:4 finished even & smooth without using extra cement complete all as specified. |
| 33 | Preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified and as directed. |
| 34 | M & L for precast cement concrete solid building blocks or slabs 10cm thick with plain or interlocking joints with PCC type C1 1:3:6 using 20mm graded stone aggregate setting in mortar 1:4 in walls, complete all as specified and directed. |
| 35 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering |
| 36 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed by Engineer in charge |
| 37 | M & L for providing cement concrete PCC 1:2:4 type B-1 mix using 20 mm graded stone aggregate as in kerbs, stoppers, edge stones etc including use of necessary formwork, straight or curved, finishing exposed surfaces etc complete all as specified and directed.. |
| 38 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm or removing the earth in hard/dence soil all as specified and directed. |
| 39 | M&L for Plain cement concrete 1:3:6, Type C2 using 40mm graded stone aggregate as in foundation, filling and mass concrete etc., complete all as specified and directed. |
| 40 | S&F of Structural Steel work as columns, posts, stanchions etc using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 all as specified and directed. |
| 41 | S&F of Structural Steel work as in main and cross beams, hip and jack rafters, purlins where connected to common rafters , vertical posts, etc fixed with angle cleats or other connecting plates, cleats etc. using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 all as specified and directed. |
| 42 | S&F of Structural Steel work in tubular trusses including special shaped washer etc.. using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 all as specified and directed. |
| 43 | M&L for Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment |
| 44 | S&F Pre painted galvalume aluminium zinc coating GI based corrugated sheet 0.5mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall with self tapping screws complete all as specified and as directed. |
| 45 | M&L for rendering 15 mm in Cement Mortar 1:4 on fair faces of brick work or concrete surface walls finished fair and even complete all as specified and as directed. |
| 46 | M&L for 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms,etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade incl screed bed or bedding layer of mortar 20mm thick for laying floor finishes in CM (1:4) etc complete all as specified. |
| 47 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. Please Enable Macros to View BoQ information 333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333 33333.0 3333.0 3333333.0 3.33333333333333e+98 33333333333333.0 3.33333333333333e+52 |
| 48 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. Please Enable Macros to View BoQ information 333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333333 33333.0 3333.0 3333333.0 3.33333333333333e+98 33333333333333.0 3.33333333333333e+52 |
AI Tender Summary
Tender Timeline
Aug 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodaySep 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender