Tender For Repair / Replacement Of Ceiling, Wall Panelling, Flooring And Allied Works In Zone A And B Of Age (I) Chakrata Under Hq Cwe Dehradun
Tender Value
85 Lakhs
Estimated cost
Bid Submission
28 Sep 2026
21 days left
EMD
1.52 Lakhs
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dehradun → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Replacement Of Ceiling, Wall Panelling, Flooring And Allied Works In Zone A And B Of Age (I) Chakrata Under Hq Cwe Dehradun
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed . |
| 2 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cementlime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing the debris outside from defence land complete all as specified and directed . |
| 3 | Dismantling unframed timber scantling 40 sqcm and over in section,in any position all as specified and directed. |
| 4 | Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in any position unframed work. |
| 5 | Dismantling boarding, any description, fixed in any position with nails complete all as specified. |
| 6 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs / blankets, any thickness, including cover fillets complete all as specified. |
| 7 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings (incl breaking of chimney/Dormer/ventilator of any size & type without damaging the existing sheet and structure wherever required and removing the debris outside from defence land) complete all as specified and directed. |
| 8 | S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed. |
| 9 | S&F MS steel flat iron as in wind tie for roof sheet including securing bolts confirming to Fe 410-W (Gde-E- 250) Quality-A complete all as specified and directed. |
| 10 | S&F for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 11 | S&F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall and facia (as per existing design) fixed with self tapping screws complete all as specified and directed. |
| 12 | Dismantling floor, wooden flooring, wooden boarding/planks, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed . |
| 13 | M&L for PCC 1:3:6 type C-2 (40mm graded stone agg) 100mm thick as in base/ sub base complete all as specified and directed. |
| 14 | M&L 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate in floor to receive the surface of tiles complete all as specified and directed |
| 15 | S&F Non skid / anti skid ceramic coloured floor tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and directed . |
| 16 | S&F Non skid/ anti skid ceramic Coloured floor tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and directed. |
| 17 | All as per item No 16 but in skirting over and including 10mm thick paster in CM 1:4 complete all as specified and directed. |
| 18 | S&F light shade vitrified ceramic tiles 10mm thick n.exc 0.36 Sqm each in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed. |
| 19 | All as per item No 18 but in skirting over and including 10mm thick paster in CM 1:4 complete all as specified and directed. |
| 20 | M&L for coloured Glazed ceramic tiles in vertical surface such as dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles complete all as specified and as directed. |
| 21 | S&F light shade Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 22 | All as per item No 21 but in skirting over and including 10mm thick paster in CM 1:4 complete all as specified and directed. |
| 23 | M&L Screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specified. |
| 24 | M& L Rendering 10mm thick in CM 1;4 on fair faces of brick work or concrete surfaces complete all as specified and directed. |
| 25 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding laid over 20 mm thick screed bed in CM 1:4 rates including moulding and rounding complete all as specified and directed. |
| 26 | M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 27 | Supply and fix Anodised aluminium snap grid frame work for false ceiling Size of grid 605 x 605mm including Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5 mm dia. 40mm long complete and including materials and labours for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed complete all as specified and directed. |
| 28 | Supply and fix Anodised aluminium snap grid frame work for false ceiling Size of grid 605 x 605mm including Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5 mm dia. 40mm long complete and including materials and labours for 12 mm thick of size 600x600mm PVC (Polyvinyl chloride) boards with water proofing PVC sheet on one side and prelaminated decorative PVC sheet on other side fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed in ceiling flat or sloping complete all as specified and directed. |
| 29 | S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed. |
| 30 | S&F for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified and directed. |
| 31 | S&F for 18/19mm thick WPC (wood plastic composite) waterproof & termiteproof boarding for wall paneling etc inclusive of fixing on to wall as specified and directed. |
| 32 | M&L applying two coats of synthetic enamel paint on steel & iron surfaces of any desciption not otherwise, described over 10cm width or girth including preparation of new surface & applying one coat of red oxide all as specified and directed. |
| 33 | M&L for preparation of new or previously untreated surfaces of steel of any description, not exc 10cm in width or girth when unconnected with other painting and apply two coats of synthetic enamel paint over a coat of red oxide all as specified and directed. |
| 34 | M & L Brick work old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. |
| 35 | M & L Brick work old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. |
| 36 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed. |
| 37 | M&L 10 mm thick renedering on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed. |
| 38 | M&L 15mm thick rendering on fair faces of brick surfaces in CM (1:4), finished surfaces even and smooth without using extra cement complete all as specified and directed. |
| 39 | M&L for preparation of newly plastered surfaces of wall and applying two coats distmper oil emulsion over a coat of primer and avg 1 mm thick wall care putty complete all as specified and directed. |
| 40 | M&L for preparation of newly plastered surfaces of wall and applying two coats cement base paint over a coat of alkali resistant priming complete all as specified and directed. |
| 41 | Preparation of old decorated plastered/un-plastered surfaces of wall at any height, pillars, cornices and making surface good at any height including necessary scaffolding and applying one coat of oil bound distemper including following :- (i) Use of all scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures.(ii) Removing of nails, making good holes, cracks etc. (iii) Work in patches and narrow widths, bands, cornices, plasteres etc and cutting in edges to line where necessary. (iv) Spreading and removing coverings to doors, windows, floors, fittings etc to protect them from splashes.(v) Removing and replacing furniture, moveable cupboard, chicks, blinds etc.(vi) Cleaning of bush, shrubs, vegetation, grass, weed, saplings etc.(vii) Washing floors, cleaning glass, joinery, electric fittings,wiring etc., of drops and splashes and leaving premise, clean and tidy etc.complete all as specified and as directed. Note - Rates are inclusive of repairing surfaces of damaged portion with putty if required. |
| 42 | Preparation of old decorated plastered/un-plastered surfaces of wall at any height, pillars, cornices and making surface good at any height including necessary scaffolding and applying one coat of cement base paint including following :- (i) Use of all scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures.(ii) Removing of nails, making good holes, cracks etc. (iii) Work in patches and narrow widths, bands, cornices, plasteres etc and cutting in edges to line where necessary. (iv) Spreading and removing coverings to doors, windows, floors, fittings etc to protect them from splashes.(v) Removing and replacing furniture, moveable cupboard, chicks, blinds etc.(vi) Cleaning of bush, shrubs, vegetation, grass, weed, saplings etc.(vii) Washing floors, cleaning glass, joinery, electric fittings,wiring etc., of drops and splashes and leaving premise, clean and tidy etc.complete all as specified and as directed. Note - Rates are inclusive of repairing surfaces of damaged portion with putty if required. |
| 43 | M&L including preparing surfaces of old wooden surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed. |
| 44 | M&L including preparing surfaces of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of aluminum paint on steel surface. |
| 45 | Preparation of old decorated plastered/un-plastered surfaces of wall at any height, pillars, cornices and making surface good at any height including necessary scaffolding and applying one coat of Weather proof exterior emulsion paint complete all as specified and directed including following :- (i) Use of all scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures.(ii) Removing of nails, making good holes, cracks etc. (iii) Work in patches and narrow widths, bands, cornices, plasteres etc and cutting in edges to line where necessary. (iv) Spreading and removing coverings to doors, windows, floors, fittings etc to protect them from splashes.(v) Removing and replacing furniture, moveable cupboard, chicks, blinds etc.(vi) Cleaning of bush, shrubs, vegetation, grass, weed, saplings etc.(vii) Washing floors, cleaning glass, joinery, electric fittings,wiring etc., of drops and splashes and leaving premise, clean and tidy etc.complete all as specified and as directed. Note - Rates are inclusive of repairing surfaces of damaged portion with putty if required. |
| 46 | M & L for Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified. |
| 47 | S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity, hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank and removing to store. Complete all as specified and directed. |
| 48 | S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity, hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank and removing to store. Complete all as specified and directed. |
| 49 | S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 210 gms). Complete all as specified and directed. |
| 50 | S&F ball valves for 15 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 142 gms). Complete all as specified and directed. |
| 51 | Taking down Chowkhats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 52 | Taking down Chowkhats or frames exc 1.50 sqm but n.exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 53 | Taking down Shutters of any description area exc 1 sqm but n.exc 2 sqm each and removing to store complete all as specified and directed. |
| 54 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibers (wood powder/rice husk/wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/sqmm, modules of elasticity 900 N/sqmm & resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia & length complete as per direction of Engineer-in-Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately). Note : For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e., depth & width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 55 | Providing & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibers (wood powder/rice husk/wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum & screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/sqmm, modulus of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter & fixing with stainless steel/ Aluminium butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as per direction of Engineer-in-Charge.(Note: stainless steel/Aluminium butt hinges and necessary S S /Aluminium screws shall be paid separately) |
| 56 | S & F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain coloured PVC sheet reinforced with MS square tube as specified & directed. |
| 57 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails M.S frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail bottom rail on either side & as gap insert for top rail & bottom rail panel ling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stile & rails with suitable PVC sheet beading & joined together with solvent cement specified and shown on drawing complete all as specified and directed. |
| 58 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approvedmake conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 59 | S & F Anodised aluminium powder coated ( minimum 50 micron thickness) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as per specified and directed. |
| 60 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge |
| 61 | Supply and fix 75 mm size, butt hinges, extruded aluminum alloy with galvanised mild steel hinge pin, anodized and fixed type C-21 complete all as directed. |
| 62 | Supply and fix aluminium anodised barrel tower bolts 150mm long of extruded section complete all as directed. |
| 63 | S & F 150 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed. |
| 64 | S & F 300 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed complete all as specified and directed. |
| 65 | S&F in repair Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed. |
| 66 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads. Complete all as specified and directed. |
| 67 | S&F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane. Complete all as specified and directed. |
| 68 | S&F 4 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane. Complete all as specified and directed. |
| 69 | S&F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane. Complete all as specified and directed. |
| 70 | S&F in repairs mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 71 | S&F in repair, 600 mm x 450 mm bevelled edge looking mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood & fixed to wooden plugs with chromium plated brass screws & cup washers. Complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysSep 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender