Tender For Special Repair To Plumbing, Joinery And Galvalume Sheet For Md Accn P-40 At Srinagar Colony Under Age B/R-Ii Of Ge Minniebay, Sri Vijaya Puram (8868/E8)
Tender Value
24.25 Lakhs
Estimated cost
Bid Submission
21 Sep 2026
5 days left
EMD
48500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Plumbing, Joinery And Galvalume Sheet For Md Accn P-40 At Srinagar Colony Under Age B/R-Ii Of Ge Minniebay, Sri Vijaya Puram (8868/E8)
BOQ
| Sl. No. | Item Description |
| 1 | Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key etc., complete all as specified and as directed. |
| 2 | M&L for rendering 10mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth etc., complete all as specified and as directed. |
| 3 | M&L for rendering 5mm thick ceiling plaster in CM (1:3) on concrete surfaces finished even & smooth (without using extra cement) etc., complete all as specified and as directed. |
| 4 | M&L for rendering 5mm thick plaster in CM (1:4) over a backing coat of 10 mm thick in CM 1:6 (Total 15 mm thick) on concrete or block masonry surfaces including mixing water proofing compound on top layer as per manufactures instructions (or 3% by weight of cement) and finishing the top surfaces even and fair etc., complete all as specified and as directed. Note : Water proofing compound shall be measured and paid seperately under relevant item of this schedule as supply only. |
| 5 | Supply only Liquid water proofing compound ISI marked etc., complete all as specified and as directed. Note : WPC may apply as per manufactures instructions or 3% by the wt of cement. |
| 6 | M&L for preparation of new plastered surfaces of wall and applying two coats of Distempering with 1st quality acrylic distemper ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour as per manufacturer's specification etc., complete all as specified and as directed. |
| 7 | M&L for newly plastered surfaces and applying two coats of oil bound distemper over a coat of Chalk whiting, on plastered surfaces of ceiling etc., complete all as specified and as directed. |
| 8 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. Make :- Asian Apex Ultima and Equivalent |
| 9 | M&L preparation of new wood/wood based surfaces of exc. 10 cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of pink primer etc., complete all as specified and as directed. |
| 10 | M&L for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc., complete all as specified and as directed.Note :- On truss work & new pressed steel frame |
| 11 | M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc and applying two coats of oil emulsion distemper over a coat of primer etc., complete all as specified and as directed. |
| 12 | M&L for applying a layer of 1mm thick wall care putty on wall and making surface even and smooth etc., complete all as specified and as directed. |
| 13 | M&L for complete removal of existing treatment and preparation of old surfaces of CEILING and applying two coats of oil emulsion distemper over a coat of primer etc., complete all as specified and as directed. |
| 14 | M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc and preparation of old external surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, complete all as specified and as directed.Make :- Asian Apex Ultima and Equivalent |
| 15 | Demolition of precast concrete work built in cement mortar including all quoins arches pillars etc., complete all as specified and as directed. |
| 16 | M&L for Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc.10 cm in width and setting in cement mortar 1:6, etc., complete all as specified and as directed. |
| 17 | Dismantling floor, hearth or wall tiles including cement mortar bedding (but not backing) and removing serviceable tiles to stores and rubbish off the premises etc., complete all as specified and as directed. |
| 18 | M&L for coloured non-skid ceramic tiles 7 to 8 mm thick exc. 0.06 sqm but n.exc 0.11sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6) etc., complete all as specified and as directed. |
| 19 | M&L for glazed ceramic coloured/printed tiles 450x350x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over 10mm thick backing in cement mortar (1:3) etc., complete all as specified and as directed. |
| 20 | Dismantling of stone slabs and tiles of any description or thickness in floors, approns and laid bedded and pointed in any mortar etc., complete all as specified and as directed. |
| 21 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM(1:6) etc., complete all as specified and as directed. |
| 22 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified. |
| 23 | Taking down chowkats or frames (without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.(including Aluminium windows/ventilators) etc., complete all as specified and as directed. |
| 24 | Taking down chowkats or frames (without taking off shutters from the frame) area n.exc 1.5 Sqm each.(including Aluminium windows /ventilators) etc., complete all as specified and as directed. |
| 25 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note :- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. |
| 26 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note :- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. |
| 27 | S&F for Factory made double extruded WPC (Wood Polymer Composite) solid door & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length etc., complete all as specified and as directed. Note :- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. |
| 28 | S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. Note: stainless steel butt hinges and necessary S S screws incl in this item |
| 29 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately |
| 30 | S&F for second class hard wood 35 mm thick glazed or guazed and skeleton shutters open rebated and prepared to receive glass, gauge etc divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars fitted with cut and mitred beads for securing glass etc including necessary arrangements to fit with pressed steel frame etc., complete all as specified and as directed. |
| 31 | Providing and fixing factory made uPVC any colour fixed window area not exceeding 1.00 sqm each made of extruded profiles with wall thickness of 2.3mm(+-0.2mm), Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified and as directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose. |
| 32 | S&F for 4mm thick ordinary quality sheet glass and glazing with oil putty in square n.exc.0.50 sqm in each pane etc., complete all as specified and as directed. |
| 33 | S&F for 4mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sq.m in each pane etc., complete all as specified and as directed. |
| 34 | S&F for Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples etc., complete all as specified and as directed. |
| 35 | S&F for 150 mm long and including ISI marked Stainless Steel butt hinges with necessary screws complete all as directed. |
| 36 | S&F for 150mm long bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. |
| 37 | S&F for 300 mm long and 12-14 mm dia rod Matt finished stainless steel sliding doors bolts (ALDROP),with S.S. nuts and screws etc. incl ISI Mark Complete all as specified and directed |
| 38 | S&F for 200mm long of stainless steel tower bolt of approved make, made from high-quality SS 304 grade stainless steel, with smooth finish and corrosion resistance, complete with necessary screws and fittings. The bolt shall be of standard size, suitable for doors/windows, including installation, alignment, and testing for proper operation, all complete as per specifications and direction of the Engineer-in-Charge. |
| 39 | S&F in repair for 150mm Floor door stoper of aluminium alloy and tounge, anodised, with hard drawn steel sring, fixed in door etc., complete all as specified and as directed. |
| 40 | S&F in repair for door helical spring mild steel 300mm, ordinary rat tail rod patteren including roller and roller plate etc., complete all as specified and as directed. |
| 41 | S&F in repair stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets etc., complete all as specified and as directed. |
| 42 | Taking down 20mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed. |
| 43 | Taking down 25/32mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed. |
| 44 | Supply and laying of CPVC pipes 20 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors etc., complete all as specified and as directed. |
| 45 | Supply and laying of CPVC pipes 25 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors complete all as specified. |
| 46 | Cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing etc., and making good, cutting not exceeding 10 cm girth etc., complete all as specified and as directed. |
| 47 | Taking down eaves gutter and rain / waste water pipes including all fittings any size and pattern etc., complete all as specified and as directed. |
| 48 | S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing as required etc., complete all as specified and as directed. |
| 49 | S&F for 110 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed. |
| 50 | S&F for 110 mm bore PVC (SWR) branch piece,single (single Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 51 | S&F for 110 mm bore PVC (SWR) branch piece,double (double Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 52 | S&F for 110mm bore PVC (SWR) junction single, (single T) equal or unequal with access door etc., complete all as specified and as directed. |
| 53 | S&F for 110 mm bore PVC (SWR) couplers etc., complete all as specified and as directed. |
| 54 | S&F for 110 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed. |
| 55 | S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing on walls as required etc., complete all as specified and as directed. |
| 56 | S&F for 75 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed. |
| 57 | S&F for 75 mm bore PVC (SWR) branch piece,single (single Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 58 | S&F for 75 mm bore PVC (SWR) branch piece,double (double Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 59 | S&F for 75 mm bore PVC (SWR) junction double, (double T) equal or unequal with accessa door etc., complete all as specified and as directed. |
| 60 | S&F for 75 mm bore PVC (SWR) couplers etc., complete all as specified and as directed. |
| 61 | S&F for 75 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed. |
| 62 | M&L for PVC (SWR) floor traps 75mm bore with stainless steel grating (measured seperately) including jointing to waste pipe and in cement concrete 1:2:4 type B-1 etc., complete all as specified and as directed. |
| 63 | S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement etc., complete all as specified and as directed. |
| 64 | S&F for 160 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and as directed. |
| 65 | S&F in repair of 1st quality vitreous china ware European type WC of size 540x375x415mm 'P' trap or 'S' Trap (pedestal pattern), any colour including necessary fittings (excluding flushing cistern and flush pipe) etc., complete all as specified and as directed. |
| 66 | S&F in repairs 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, any colour , with inlet, ball valve, float and handle including brackets, and necessary connections to pipes with PVC connections 20mm size with PTMT nuts of length 600mm etc., complete all as specified and as directed. |
| 67 | S&F in repairs PVC water closet seat cover (any description and any colour), closed pattern and mild steel chromium plated or aluminised hinging device etc., complete all as specified and as directed. |
| 68 | S&F in repair Heavy Duty Flexible Braided PVC waste pipe for sink and wash basin 32mm dia with length not less than 1000mm i/c PVC waste fittings of Approved make etc., complete all as specified and as directed. |
| 69 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position etc., complete all as specified and as directed. |
| 70 | S&F in repair 600x450mm size and 4 mm thick beveled edge looking mirror of selected quality glass, having PVC moulding/beading all around, mounted on 5mm thick PVC board, with and incl fixing accessories etc., complete all as specified and as directed. |
| 71 | S&F in repairs 600 mm long CP Brass Towel Rail 20 mm dia fixed to wall with necessary chromium plated screws and wall plugs etc., complete all as specified and as directed. |
| 72 | S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to CPVC/ steel pipe or union etc., complete all as specified and as directed. |
| 73 | S&F in repair Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed. |
| 74 | S&F in repair to Bib Taps, cast copper alloy heavy duty, 15 mm dia, Chromium Plated, long body Fancy Type screwed down for iron pipe and fixed etc., complete all as specified and as directed. |
| 75 | S&F in repair two way bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed. |
| 76 | S&F in repairs 15 mm dia Stop cock chromium plated fancy type with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe/CPVC pipe or for unions and fixed etc., complete all as specified and as directed. |
| 77 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long etc., complete all as specified and as directed. |
| 78 | S&F in repair 125 mm dia CP grating incl joints with solvent cement etc., complete all as specified and as directed. |
| 79 | S&F in repair Kitchen sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including waste fittings like 40mm CP waste couplings etc., complete all as specified and as directed. |
| 80 | S&F in repair stainless steel plate rack of size 900x 750 x 250 mm made of 1.00mm thick stainless steel fixed into wall with necessary brass screws and plugs etc., complete all as specified and as directed. |
| 81 | Dismantling wrought iron or mild steel work of any description and any position as directed. Note :- MS Gates and MS railing only taken |
| 82 | M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe.290.Gde-E-165 etc., complete all as specified and as directed. |
| 83 | M&L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment confirming to Fe 410 -W (Gde- E- 250) quality- A etc., complete all as specified and as directed. |
| 84 | S&F Mild steel screw bolts (machine made) 5 to 10 mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n.exc. 10 cm long etc., complete all as specified and as directed. |
| 85 | Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering, complete all as specified and directed. |
| 86 | S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.Note : Height of the bldg up to G+3 storey including necessary safety arrangements |
| 87 | S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing complete all as specified and as directed. Note : Height of the bldg up to G+3 storey including necessary safety arrangements |
| 88 | S&F Aluminium flat iron work in wind ties 40x6mm size fixed with 50mm/ 75 mm aluminium self staging screws with integral EPDM washer screwed in roof covering all as directed.Note :- Height of the bldg up to 15 mtrs including necessary safety arrangements |
| 89 | Dismantling of wall / ceiling boards (fiber, pulp, insulation etc) / insulation boards /slabs/blankets of any thickness including cover fillets ridges etc, complete all as specified and directed. |
| 90 | Providing & fixing false ceiling with perforated 12mm thick micro tegular edged GRG false ceiling tiles at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysSep 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender