Tender For Construction Of Shooting Range, Changing Room, Swimming Pool And Lawn Tennis Court At Ch Awat
Tender Value
7.23 Crore
Estimated cost
Bid Submission
21 Sep 2026
17 days left
EMD
14.46 Lakhs
Bank guarantee accepted
Document Fee
11800
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Champawat → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Shooting Range, Changing Room, Swimming Pool And Lawn Tennis Court At Ch Awat
BOQ
| Sl. No. | Item Description |
| 1 | DSR Item- 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil. |
| 2 | DSR Item- 2.26.1Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil |
| 3 | DSR Item- 2.25Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | NSI Item-Disposal of Excavated earth/rock unserviceable, upto dumping zone near national highway distance upto 20km from site |
| 5 | DSR Item- 2.27Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. |
| 6 | DSR Item- 2.35.3.1Diluting and injecting chemical emulsion (Chlorpyriphos/ Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment) |
| 7 | DSR Item- 4.1.8Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 8 | DSR Item- 4.11Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). |
| 9 | DSR Item- 4.13Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 10 | DSR Item- 4.1.3P/L cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 11 | DSR Item- 4.1.10P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 12 | DSR Item- 5.1.2Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lIll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 13 | DSR Item- 5.33.1.1Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level. Concrete of M25 grade with minimum cementcontent of 330 kg /cum |
| 14 | DSR Item- 5.33.2.1Providing M-30 grade concrete BMC/ RMC. (Note : Cement content considered in M-30 is @ 340 kg/ cum) for columns, pillars piers etc. |
| 15 | DSR Item- 5.35Add for using extra cement in the items of design mix over and above the specified cement content therein. |
| 16 | DSR Item- 5.9Centering and shuttering including strutting, propping etc. and removal of form for : |
| 17 | DSR Item- 5.9.1Foundations, footings, bases of columns, etc. for mass concrete |
| 18 | DSR Item- 5.9.2Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 19 | DSR Item- 5.9.6Columns, Pillars, Piers, Abutments, Posts and Struts |
| 20 | DSR Item- 5.9.5Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 21 | DSR Item- 5.9.3Suspended floors, roofs, landings, balconies and access platform for Suspended floors, roofs, landings, |
| 22 | DSR Item- 5.9.7Stairs, (excluding landings) except spiral-staircases |
| 23 | DSR Item- 5.9.19Weather shade, Chajjas, corbels etc., including edges |
| 24 | DSR Item- 5.22.6Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 25 | DSR Item- 6.1.2Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 26 | DSR Item- 6.4.2Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 27 | DSR Item- 6.13.2Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 28 | DSR Item- 6.15Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 29 | DSR Item- 9.20.1Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 30 | DSR Item- 9.21Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 31 | DSR Item- 9.70Providing and fixing ISI marked Bright finished M.S. fitting for door windows. |
| 32 | DSR Item- 9.75.2250x16x5 mm sliding door bolts |
| 33 | DSR Item- 9.74.1250x10 mm Tower bolt |
| 34 | DSR Item- 9.74.3150x10 mm Tower bolt |
| 35 | DSR Item- 9.81.1125 mm handles |
| 36 | DSR Item- 9.81.2100 mm handles |
| 37 | DSR Item- 9.101.2hanging floor door stopper, Twin rubber stopper |
| 38 | DSR Item- 9.68.3200 Casement stays (straight peg type) with necessary screws etc. complete, weighing not less than 120 gms |
| 39 | DSR Item- 9.23Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 40 | DSR Item- 21.1.1.2Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portition: Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 41 | DSR Item- 21.3.2Providing and fixing glazing in uPVC/aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) |
| 42 | DSR Item- 21.8.1Filling the gap in between uPVC, aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete: Upto 5mm depth and 5 mm width |
| 43 | DSR Item- 10.14.2.1Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: (A) \\"Profile C\\" Fixing with adjustable lugs with split end tail to each jamb |
| 44 | DSR Item- 10.15.1Providing and fixing M.S. Tubular frames for Windows, Ventilators with rectangular/ L-Type sections, made of 2.0 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer: Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 45 | DSR Item- 10.16.1Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 46 | DSR Item- 9.48.1Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding |
| 47 | DSR Item- 9.51.2Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading |
| 48 | DSR Item- 10.26.1Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube |
| 49 | DSR Item- 10.30.2Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes |
| 50 | DSR Item- 25.8Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi- etallic contacts, all complete to perform as per Specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof.The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. |
| 51 | DSR Item- 10.6.1Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover |
| 52 | DSR Item- 10.7Providing and fixing ball bearing for rolling shutters. |
| 53 | DSR Item- 10.8.1Extra for providing mechanical device chain and crank operation for operating rolling shutters.Exceeding 10.00 sqm and upto 16.80 sqm in the area |
| 54 | DSR Item- 11.452 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix: 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 55 | DSR Item- 11.41.2Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm |
| 56 | DSR Item- 11.46.2Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 57 | DSR Item- 11.39Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. |
| 58 | DSR Item- 8.31Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 59 | DSR Item- 11.56Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as pecified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 60 | DSR Item- 11.26.1Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 61 | DSR Item- 11.27Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 62 | DSR Item- 11.53Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge: |
| 63 | DSR Item- 11.48.2Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm |
| 64 | DSR Item- 16.75Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately). |
| 65 | DSR Item- 11.6Cement plaster skirting 18 mm thick up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. |
| 66 | DSR Item- 11.8Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc. |
| 67 | DSR Item- 12.54.1Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of theroom with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with the help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c’/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with the help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G | sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 68 | DSR Item- 12.52.3Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 69 | DSR Item- 22.3Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). |
| 70 | DSR Item- 13.3.120 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) |
| 71 | DSR Item- 13.16.16 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 72 | DSR Item- 13.1.212 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 73 | DSR Item- 13.2.215 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) |
| 74 | DSR Item- 13.46.1Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 75 | DSR Item- 13.41.1Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 76 | DSR Item- 13.47.1Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 77 | DSR Item- 13.62.1Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 78 | DSR Item- 13.80Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 79 | DSR Item- 14.90.1Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm Thick |
| 80 | DSR Item- 12.21Providing gola 75x75 mm in cement concrete (1:2:4). |
| 81 | DSR Item- 22.14.1Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 82 | DSR Item- 22.1.1Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) including applying of twice ( at base and top of mortar ) cement slurry @ 2.2kg/m2 (each time) mixed with water proofing compoundconforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and groutedwith cement slurry mixed with water proofing compound2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions.Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone. |
| 83 | DSR Item- 22.2.1Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough Kota stone. |
| 84 | DSR Item- 19.19.1.1Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions |
| 85 | DSR Item- 19.19.4.1Providing and fixing in position pre cast RCC manhole cover and frame of required shape and of approved quality. EHD - 35 : Circular shape 560 mm internal dia |
| 86 | DSR Item- 19.15.1Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar |
| 87 | DSR Item- 19.32.1Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 88 | DSR Item- 23.1.1Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia |
| 89 | DSR Item- 23.5Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge |
| 90 | DSR Item- 23.6Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge |
| 91 | DSR Item- 23.7Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. |
| 92 | DSR Item- 23.8Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge. |
| 93 | DSR Item- 23.3.2Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia |
| 94 | DSR Item- 23.4.2Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia |
| 95 | DSR Item- 23.13.2Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia. |
| 96 | DSR Item- 23.14.2Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts f required size complete. 150 mm clamp |
| 97 | DSR Item- 23.15.2Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I): 150 mm dia. |
| 98 | DSR Item- 19.6.2Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe |
| 99 | DSR Item- 17.1.1Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 100 | DSR Item- 17.7.1Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 101 | DSR Item- 17.3.1Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 102 | DSR Item- 17.32.4Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm |
| 103 | DSR Item- 12.41.2P/L 110 mm dia UPVC soil waste pipe with pressure 6kg/CM2 for sewer. |
| 104 | DSR Item- 17.73.2Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms |
| 105 | NSI Item-P/F Upvc nahani trap 110x110mm dia |
| 106 | DSR Item- 18.65Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 107 | DSR Item- 12.43.2Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 108 | NSI item-P/F Upvc terminal guard 110 mm dia |
| 109 | DSR Item- 18.74.2Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length |
| 110 | DSR Item- 12.42.5.2Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend |
| 111 | NSI item-P/F Upvc door bend 110 mm dia. |
| 112 | DSR Item- 17.28.2.1Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia |
| 113 | DSR Item- 12.42.4.2Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110x110x110 mm tee |
| 114 | DSR Item- 17.8P/F white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 115 | DSR Item- 17.5.2Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern |
| 116 | DSR Item- 8.10.2Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade |
| 117 | DSR Item- 17.10.1.2Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 225 mm |
| 118 | DSR Item- 12.41.2Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 119 | DSR Item- 12.42Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 120 | DSR Item- 12.42.5.2110 mm bend |
| 121 | DSR Item- 12.42.6.2110 mm Shoe |
| 122 | DSR Item- 12.42.4.2110x110x110 mm tee |
| 123 | DSR Item- 12.22Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4). |
| 124 | DSR Item- 12.43.2Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm |
| 125 | DSR Item- 18.11.1Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :15 mm dia nominal bore |
| 126 | DSR Item- 18.10Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 127 | DSR Item- 18.10.220 mm dia nominal bore |
| 128 | DSR Item- 18.10.325 mm dia nominal bore |
| 129 | DSR Item- 18.12.4Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore |
| 130 | DSR Item- 18.49.1Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore |
| 131 | DSR Item- 18.52.1Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore |
| 132 | DSR Item- 18.17Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 133 | DSR Item- 18.17.1.A20mm nominal bore |
| 134 | DSR Item- 18.17.125 mm nominal bore |
| 135 | DSR Item- 18.17.232 mm nominal bore |
| 136 | DSR Item- 18.58.1.1Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia |
| 137 | DSR Item- 18.48Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 138 | DSR Item- 18.18.2Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore |
| 139 | DSR Item- 18.20.3Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore |
| 140 | DSR Item- 18.51.1Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 141 | DSR Item- 18.53.1Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore |
| 142 | DSR Item- 18.64Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms |
| 143 | DSR Item- 16.1Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. |
| 144 | DSR Item- 16.2Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). |
| 145 | DSR Item- 16.3.10Supplying and stacking at site. Moorum |
| 146 | SOR Item- 4-14-AGranular Sub-base with Well Graded Material (Table 400.1) By Mix in Place MethodConstruction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading I Material |
| 147 | SOR Item- 4-9Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC inmechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. (By Mechanical Means with 1 km lead) |
| 148 | SOR Item- 5-3-1Bituminous MacadamProviding and laying bituminous macadam with hot mix plant using crushedaggregates of grading as per Table 500.4 premixed with bituminous binder,transported to site upto a lead of 1000 m laid over a previously prepared surfacewith paver finisher to the required grade, level and alignment and rolled to achievethe desired compaction as per Technical Specification Clause 504.(Bitumen VG-10 @ 3.3% of the weight of mix has been used for analysis purpose.The choice of bitumen will depend upon the prevailing site conditions and shall be inaccordance with Clause 504 of MORD) with Bitumen VG-10 |
| 149 | SOR Item- 5-05ABituminous Concrete Bituminous Concrete Grading -I (Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.2 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher withsensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete inall respects) |
| 150 | SOR Item- 5-12Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete. |
| 151 | SOR Item- 5-02(I)Providing and applying tack coat using bitumen emulsion conforming to IS: 8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom. With medium setting bitumen emulsion : On W.B.M / W.M.M. @ 0.4kg/sqm |
| 152 | NSI Item-Providing and Laying of ITF Certified 8 Layer Acrylic Synthetic Cushion Court flooring including primer (layer 1), resurfacer (layer 1), Cushion (2 layers), resurfacer (layer 1), 2 layer of color, complete in all aspects as per direction of Engineer-in-charge. |
| 153 | NSI Item-Tennis Pole with NetProviding & Fixing Aluminium Tennis Pole made of 80mm × 80mm square pipe with special internal ratchet system for tightening the net. This enables perfect tension control for the net. Top cover made from cast, Aluminium with pulley. The use of branded Epoxy Paint. |
| 154 | NSI Item-Tennis Digital Score BoardProviding and installing LED Tennis Score Board of dimension 9' x 6' with alphabet and digit height of 6\\" and with provision of the names of 2 players or team, games and sets. |
| 155 | NSI Item-Providing of Tennis Refree Chair foldable. Construction with all steel and metal and foam padded seat. Height of 6 ft. |
| 156 | NSI Item-LE-1000 DIA TOP MOUNTSIZE - 1000 DIA ( 40\\" )Top Mount FRP FILTERWith 6 Way Multiport Valve |
| 157 | NSI Item-Motor 3 HP IP 55 Rating with pre filters.Total Electrical SeparationAmbient temperature up to 50 Degree C.Capacitor Inside. |
| 158 | NSI Item-Water Test KitBasic Ph & CI Test KitPhinol Red - 15 mIOrthotodiline - 15 mI |
| 159 | NSI Item-Hose PipeSize – 15 mtr.Extruded PE Vaccum HoseQuality - PE |
| 160 | NSI Item-Algae Stainless Steel Brush( Hi- Grade Stainless Steel with Aluminum handle)Size – 10”Weight – 190gm |
| 161 | NSI Item-Standard wall Brush(Poly bristle Wall Brush with Aluminum handle)Size – 18”Weight - 320gm |
| 162 | NSI Item-Leaf NetHeavy Duty Plastic Leaf Net Write Long Instead of Blue |
| 163 | NSI Item-VACUUM HEAD 18 INCHIVacuum head with 4 wheel , Alu BodySize - 18 inch, Weight – 2.20 Kgs |
| 164 | NSI Item-Floor Inlet NozzleBody – ABS FiberColor – WhiteFlow Rate – 45M3/hrMultiple flow UV Protected Appreciated for long life.Connection 50mm/63mmSuitable for 10n& 6 Kg Pressure. |
| 165 | NSI Item-Suction NozzleBody – ABS FiberColor – White |
| 166 | NSI Item-Swimming Pool Under Water Light12v - 27w 9Under Water Light12v - 27wSize = 9 INCHBody Type = SSONE YEAR WARRANTYIP 68 Rating |
| 167 | NSI Item-LED driver for Above Light |
| 168 | NSI Item-Filter Media |
| 169 | NSI Item-12 Inch Single Pin White (Per Mtr)Swimming Pool Over Flow GratingColor Blue,WhiteUV ProtectedMake by Blue AidMaterial –PP,CP, Natural DanaHeavy Duty/Non Skid |
| 170 | NSI Item-Square Main DrainColor – WhiteFlow Rate – 850L/MinSquire Main Drain 300mm x 300mm Material – ABS |
| 171 | NSI Item-FOUR STEP LADDER4 STEP LADDERMATERIAL - STAINLESS STEEL304 GRADEPool Ladder is made with highquality gradeStainless Steel 38 mmTube for reliability and durabilitycomplete with anchoring fixtures |
| 172 | NSI Item-54 KW POOL HEATERPool Heating SystemSupply of online Pool Heater 3 Phase Operating per batch |
| 173 | NSI Item-ADHESIVE (50kg Bag)Adhesive (Tile Pasting)Packaging – 50kg BagsUses - 200 Sqft (Per Bag) |
| 174 | NSI Item-EPOXY GROUT (10 KG BAG)Epoxy Grout (Tiles Gap Filling)Packing – 10Kg BagUses - 90 Sqft (Per Bag) |
| 175 | NSI Item-Waterproofing (Per Sqft.)Providing 3 coating of water proof inside of pool to prevent of leakage |
| 176 | NSI Item-INSTALLATION WITH MATERIALALL FITTING MATERIAL WITH SERIVCE |
| 177 | NSI Item-CONSULTANCY |
| 178 | NSI Item-FINAL TESTING AND HANDOVER |
| 179 | SOR Item- 3-03Excavation in Soil with Dozer with lead upto 1000 metres ( EExcavation for road way in soil by mechanical means including cutting and transporting the earth to site of embankment/dumping area with lead upto 1000 metres, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.)(70 % of 2799.12 Total Excavation) |
| 180 | SOR Item- 3-04Excavation in Ordinary Rock with Dozer with lead upto 1000 metres (Excavation for roadway in ordinary rock by deploying a dozer, including cutting and transporting the earth to site of embankment/dumping area with lead upto 1000 metres, trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.) Ordinary rock (20 % Total Excavation) |
| 181 | SOR Item- 3-08AExcavation in Hard Rock (blasting prohibited) (Excavation for roadwork in Hard Rock (blasting prohibited) with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000 m.) Mechanical Method. Hard rock (10 % Total Excavation) |
| 182 | SOR Item- 11-2-2Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9. Earth filling (For marshy soil) |
| 183 | SOR Item- 3-4Construction of Embankment with Material Obtained from Borrow PitsConstruction of embankment with approved material obtained from borrow pits witha lift upto 1.5 m, transporting to site, spreading, grading to required slope andcompacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 mas per Technical Specification Clause 301.5 |
| 184 | SOR Item- 2-2Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203 |
| 185 | SOR Item- 1-4Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203, Random rubble masonry In cement mortar (1:4) |
| 186 | SOR Item- 12-5-2-1Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (For height upto 5 m) P.C.C. grade M 20 Nominal mix (1:2:4) |
| 187 | SOR Item- 12-9Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 |
| 188 | SOR Item- 1-5Hand Packed stone filling in back of wallls including cost of all materials, royality, T&P etc. complete as per direction of Engineer-in- charge. (As per PWD Uttarakhand specifications) |
| 189 | SOR Item- 3-03Excavation in Soil with Dozer with lead upto 1000 metres ( EExcavation for road way in soil by mechanical means including cutting and transporting the earth to site of embankment/dumping area with lead upto 1000 metres, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.) |
| 190 | DSR Item- 16.1Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. |
| 191 | SOR Item- 2-2Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203 |
| 192 | SOR Item- 4-1-A-3Granular Sub-base with Well Graded Material By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading III Material |
| 193 | SOR Item- 2-3Cement Concrete (PCC M-30) Pavement:-Construction of Un-reinforced, Cement concrete pavement, thickness as per design, over a prepeared sub base with 43 grade cement or any other type PCC Grade M-30, coarse and fine aggregates conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (Steel channel, laying and fixing of wedges, steel plates including levelling the formwork and laying and fixing of 125 micron thick polythene film, as per drawing), spreading the concrete with shovels, rakes, compacted using needle, and plate vibrators, finished in continuous operation and curing of concrete slabs for 14 days, using curing compound where specified and water finishing to lines and grade as per drawings and technical specifications. |
| 194 | SOR Item- 7-1-2Laying Cement Concrete Pipe NP3 (burried conduits) on first class bedding of granular material including fixing collar with cement sand mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonary work in head wall and parapets.300 mm dia. |
| 195 | SOR Item- 8-02-ACast in Situ Cement Concrete M 20 Kerb with Channel (Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M10 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCC M20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408) Using Concrete Mixer |
| 196 | SOR Item- 10-5Painting Two Coats on New Concrete Surfaces Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701 |
| 197 | NSI Item-Providing and fixing Best water doctor portable water purification system with inbuilt water cooler.UV |
| 198 | NSI Item-Provision of Survey |
| 199 | NSI Item-Providing 200 mm nominal dia. Casing pipe 6mm thick as per IS 389/4270 (blind pipe) |
| 200 | NSI Item-Providing 200 mm nominal dia. Casing pipe 6mm thick as per IS 389/4270 (slotted pipe) |
| 201 | NSI Item-Providing 200 mm dia. Well cap |
| 202 | NSI Item-200 mm dia M.S. bail plug |
| 203 | NSI Item-200 mm dia M.S. socket |
| 204 | NSI Item-200 mm dia center guide |
| 205 | NSI Item-Transportation of dual rotary rig machine,compressor, O.P. unit and connecting T&P required for drilling with other material upto site of work i/c loading/unloading, errection of rig machine |
| 206 | NSI Item-Drilling of 450 mm dia. Bore from G.Level to 90 m B.G.L. |
| 207 | NSI Item-Loring of 200 mm dia. Tube well assembly |
| 208 | NSI Item-Supply of 1.6 mm to 4.8 mm size pea gravel with surrounding etc. |
| 209 | NSI Item-Water arrangement with auxiluiary bore |
| 210 | NSI Item-Development of tube well by air compressure |
| 211 | NSI Item-Development of tube well by OP unit |
| 212 | NSI Item-Chemical and becteriological testing of site |
| 213 | NSI Item-100X75 mm size 3.0 m long R.S. joist for foundation |
| 214 | NSI Item-Supply of Suitable size Submersible pumping plant of KSB make (Variable discharge according the discharge 300 to 450 lpm at 30 to 40 m lead) i/c control pannel starter, gate/sluice valve, column pipe, cable etc. |
| 215 | NSI Item-Supply of spare pumping plant of above duty |
| 216 | NSI Item-Supplying 100 mm dia. G.I. heavy class as per IS 1239 1978 at rail head/central store. |
| 217 | NSI Item-Cartage of 100 mm dia. Pipe specials and fittings from site store to site of works, lowering them into trenches, laying through to aligment and gradient, laying and jointing of pipeline i/c cutting and threading of pipes for making up length as required for proper complection of works |
| 218 | NSI Item-Supply and fixing of Valve class- I IS 788/1971, i/c cartage , labour T&P etc. 100 mm dia. |
| 219 | NSI Item-Supply and fixing of Valve class- I IS 788/1971, i/c cartage , labour T&P etc. 80 mm dia. |
| 220 | NSI Item-Supply all materials, labour T&P etc and construct saluice valve chambers as per type design |
| 221 | NSI Item-Supply & Installation of Roof shingles sheet, Hip & ridge over RCC slopi roof plastered surface, all complete as per direction of the Engineer in-charge. |
| 222 | DSR Item-1.10.3Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-C |
| 223 | DSR Item-1.12Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed mediumclass PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 224 | DSR Item-1.13Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 225 | DSR Item-1.4Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 226 | DSR Item-1.14.12 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 227 | DSR Item-1.14.22 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 228 | DSR Item-1.14.42 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 229 | DSR Item-1.14.104 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 230 | DSR Item-1.18.2Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair |
| 231 | DSR Item-1.11Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 232 | DSR Item-1.31Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 233 | DSR Item-1.32Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 234 | DSR Item-1.38Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 235 | DSR Item-2.5.1Supplying and fixing of following ways surface/ recess mounting, Vartical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 4Way (4+12), Double door |
| 236 | DSR Item-2.4.2Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6way 4+18 Double Door |
| 237 | DSR Item-2.10Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral |
| 238 | DSR Item-2.10.1Single pole |
| 239 | DSR Item-2.10.2Single pole and neutral |
| 240 | DSR Item-2.10.5Triple pole and neutral |
| 241 | DSR Item-2.13Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 242 | DSR Item-2.13.140A |
| 243 | DSR Item-2.13.263A |
| 244 | DSR Item-5.4Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. |
| 245 | DSR Item-5.7Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 246 | DSR Item-1.25Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 247 | DSR Item-10.18P/F Hexagonal MS sheet fan box for ceiling fan clamp od internall dia 140mm, 73mm height top lid of 1.5mm thick MS sheet with its top surface hacked, MS clamp shall be made of 12mm dia MS bar bent to shape as per standard design. |
| 248 | DSR Item-1.33Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 249 | DSR Item-1.24Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 250 | DSR Item-1.24.15/6 A switch |
| 251 | DSR Item-1.24.43 pin 5/6 A socket outlet |
| 252 | DSR Item-1.24.6Telephone socket outlet |
| 253 | DSR Item-1.24.7TV antenna socket outlet |
| 254 | NSI item-36/40 W LED Batten tube Surya 40W6500K LED |
| 255 | NSI Item-300mm Bajaj propeller type ventlating fan with bird screen Freshee 300mm |
| 256 | DSR Item-19.1Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 3742019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 257 | NSI Item-LED 12 W Recess mounting Down Lighter Phillips DN296B |
| 258 | NSI item-20 W HE Polycab LDO0103076 20WLED6500K Batten Tube |
| 259 | NSI Item-36W 2x2 LED panel Crompton CGCEL Panel luminary |
| 260 | DSR Item-1.41Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 261 | DSR Item-1.50.1Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 262 | NSI item-Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, FRLSee standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated Building LT Panel as per specification mentioned belowINCOMER - 200 amps 36 KA FPMCCB . -1OUTGOINGS - 100 amp 30 KA FP MCCB -1 no.,- 125 amp 36 KA FP MCCB-1 nos |
| 263 | DSR Item-2.11S/F single pole blanking plate in the existing MCB DB complete etc. as required. (4 no. /MCBDB) |
| 264 | DSR Item-2.15Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. asrequired. |
| 265 | DSR Item-2.15.125 A |
| 266 | DSR Item-2.15.240 A |
| 267 | DSR Item-2.15.363 A |
| 268 | DSR Item-1.57Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. For AC |
| 269 | NSI item-Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate One Module for modular switches in recessincluding supplying and fixing Anchor Cat-6 Data Information Outlet, crimpling, connection, testing etc. as required. |
| 270 | DSR Item-1.53.2Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run |
| 271 | NSI item-Supplying installation testing commissioning of 24 Port, Gigabit Data switch Dlink with 2 U rack , cable maneger etc as reqd. |
| 272 | DSR Item-2.3.2Supplying and fixing 8 way, Double Door single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 273 | NSI item-Supply of 18W Inverter LED pr batten with backup 8 hrs |
| 274 | NSI item-10W LED Batten Wipro Garnet D631065 Polycarbonate 6500K |
| 275 | DSR Item-2.2.13Providing and fixing of 100 amps 30 KA Four pole rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required |
| 276 | DSR Item-6.12Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I.bolts, nuts, chuck nuts and spring washers etc. complete as required. |
| 277 | DSR Item-6.14Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. |
| 278 | DSR Item-1.19Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 279 | DSR Item-1.27.2Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 module |
| 280 | DSR Item-1.40Providing and fixing plain 16/0.20mm (0.50sqmm) twin circular flexible FRLS PVC insulated, PVC sheathed copper conductor cable direct on the wall with PVC clips etc. as required. |
| 281 | NSI item-Heigh Bay LED Light 100 W Ceiling mounting type Acentech AB_HB_100 |
| 282 | NSI Item-36/40 W LED Batten tube Surya 40W6500K LED |
| 283 | NSI Item-300mm Bajaj propeller type ventlating fan with bird screen Freshee 300mm |
| 284 | NSI item-Providing Gyser (water Heater) 15 Liter Capacity. 5 Star Candes |
| 285 | DSR Item-2.20Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A \\"C\\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 286 | NSI item-10 W LED Bulkhead Kinjal 10WLED Plastic |
| 287 | NSI item-Supply, installation, testing and commissioning of 4 MP COMS 0.37 inch Sensor,4MP(2560×1440) ,,1080P ( 1920 x 1080 ) ,720 P resolution, 30 mtrs Ir, day night capable, Focal Length(mm)3.6, Frame Rate (fps)30, Video Streaming Triple compressed stream,Minimum Illumination for Capturing Color Image0.03 lux WDR (Wide Dynamic Range) DWDR SNR (Signal to Noise Ratio) ≥52 Db Installation Type Outdoor with aluminium Housing, IP Bullet camera connections ,testing etc. as reqd,. |
| 288 | NSI item-Supply, installation, testing and commissioning of 4 MP COMS 0.37 inch Sensor,4MP(2560×1440) ,3MP(2304×1296) ,1080P ( 1920 x 1080 ) ,720P ( 1280 x 720 ) ,D1 ,CIF ,480 x 240 resolution, 30 mtrs Ir, day night capable, Focal Length(mm)2.8, Frame Rate (fps)30, Video Streaming Dual compressed stream,Minimum Illumination for Capturing Color Image0.002 lux WDR (Wide Dynamic Range) DWDR,SNR (Signal to Noise Ratio) 50-60 Db Installation Type Outdoor with aluminium Housing, IP Dome camera connections ,testing etc. as reqd,. |
| 289 | NSI item-Supply, installation, testing and commissioning of POE Layer 3 - access switch 24 ports, with, Management Port (RJ 45/RS 232/USB), Switching Capacity / Forwarding Bandwidth (Non Blocking / Line Rate /Wired Speed) 2x (Numbers of access ports + Number of Uplink Ports) (Gbps) 128, RAM (MB) 256, Flash Memory (MB) 128, Throughtput / Forwarding Performance (MPPS) 96, Number of VLAN Supported 4000, Number of VLAN IDs Supported 4000, Number of IPV4 Routes 500,Number of IPV6 Routes 500,Number of Mac Address Supported (k) 32, Basic Layer-3 Protocol from day 1 Static Routing,RIPv1,OSPFv2, Premium Layer-3 Protocol from day 1 802.1Qbb,802.1Qaz, DHCP Snooping,ACL,802.1x,RADIUS/ TACACS,Port Security etc. as reqd,. |
| 290 | NSI item-D-Link 6U Rack Enclosures Networking/Server Rack with cable management and Connectors etc. as reqd. D-LinkR (NWR-6U-5045-GR) |
| 291 | NSI item-64 Channels NVR with 4K (3840 × 2160), Recording Speed for all channels (fps)Upto 60, Total Storage Capacity of the hard disk provided40TB, SATA III Internal Hard Drive Interface,Internal Storage Expandable upto 16TB, Number of Hard Disks supported 8, Redundancy Option RAID 0,RAID 1,RAID 5,RAID 6,RAID 10,Conformity to Dry Heat test at Specified Maximum Operating Temperature for 16 hours as per IS :9000 latest, Conformity to Damp heat at 40 degree C - 95% RH (cyclic test): two cycles of 16+8 hours as per IS: 9000 latest, Conformity to Cold test at Specified Minimum Operating Temperature for 4 hours as per IS: 9000 latest,valid BIS certificate as per IS 13252 etc. as required. |
| 292 | NSI item-81-82 CM LCD Monitor, 1920 x 1080 (Full HD) resolution, Aspect Ratio 16:9, 250 nits brightness, Response Time (millisecond) 5 millisecond, VGA Port, HDMI Port,Display Port, Power Consumption in Operating Mode (Maximum) 36Watt, Power Consumption in Sleep Mode (Maximum 0.5Watt,Technology LED Backlit etc. as required. |
| 293 | NSI item-FES 8 Ports Managed PoE+ Layer 2 Access Switch FESR (FES-GS-1010P) |
| 294 | NSI item-HDMI1.4 Cat.6 10.2 Hdmi Extender, HDMI resolution 1080p @ 50 / 60Hz, Supported audio formats Dolby, Storage Humidity (no condensation) 5% - 95 % RH, Data transfer rate 10.2 Gbps, ISO9001 Compliance etc. as required. |
| 295 | DSR Item-1.21Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 296 | DSR Item-1.21.120 mm |
| 297 | DSR Item-1.21.225 mm |
| 298 | DSR Item-1.53.2Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run |
| 299 | NSI item-Supplyin & Installation of FES 8 Ports Managed Non POE Layer 2 Access Switch (DGS-1210-10/ME) with SFP++, along with6 port Patch Panel LIU fully loaded including Patch chord, Connectors etc. etc. as reqd. |
| 300 | NSI item-Suppling Laying and fixing of 6 core OFC Cable as reqd. |
| 301 | NSI item-SITC of Solar Pathway light with panel , Battry and 12 w LED light |
| 302 | DSR Item-18.4.2Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainlesssteel shaft, mechanical confirming to IS : 1520Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325 .M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as requiredSuitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head |
| 303 | DSR Item-18.7Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including,Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on thewall/ceiling with suitable clamp/support frame and painting with two or more coats of synthatic enamel paint of required shade complete as required : |
| 304 | DSR Item-18.7.565 mm dia |
| 305 | DSR Item-18.7.7100 mm dia |
| 306 | DSR Item-18.11Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required : |
| 307 | DSR Item-18.11.365mm |
| 308 | DSR Item-18.11.5100mm |
| 309 | DSR Item-18.12.5Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required. 100mm |
| 310 | DSR Item-18.14.5Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required.100mm |
| 311 | DSR Item-18.16.2Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required.Stainless Steel (Grade 304) |
| 312 | DSR Item-18.17.1Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket..30 mtrs |
| 313 | DSR Item-18.18.2Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required.Stainless Steel (Grade 304) |
| 314 | DSR Item-18.19.1Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required.2 way-100 mm dia M.S. Pipe |
| 315 | DSR Item-18.23.1Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.100mm |
| 316 | DSR Item-18.48Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 317 | NSI Item-Providing and fixing carbon-di-oxide fire extinguishers trolley mounted with all accessories internal discharge tube,high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:2878 Finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Capacity 22.5 Kg. |
| 318 | NSI Item-Providing and fixing Carbon-di-oxide Fire Extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube. 30cms long high pressure discharge hose. Discharge nozzle,suspension bracket, confirming to IS:934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. (CCOE Nagpur Approved clynders). Capacity 4.5 Kg. |
| 319 | NSI Item-Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.4 kg. capacity |
| 320 | NSI Item-Providing & fixing carbon steel Fire man axe with rubber insulated handle tested to 20000 volts. |
| 321 | NSI Item-Providing and fixing Mechanical foam ( AFFF) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.Capacity 9 Ltr. |
| 322 | NSI Item-Providing and Fixing of self illuminated /auto glow Exit signs printed on photoluminescent sheet containing self illuminated base chemical,of appropriate size not less than 400x150mm,suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysSep 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender