Tender for PUMP AND MOTOR REPAIR

Sharing tender

Pump And Motor Repair - Cable Joint,G.L. Pipe Threading Including Transportation,Labour Charges (For Over Hauling),Supply And Fixing Of Ct Coil 50/5 & 75/5,Supply And Fixing Of Blade Set 25A,Supply And Fixing Of Blade Set 16A(Mr),Supply And Fixing Of Hylum Brand Hand Plastic Sheet 3Mm Thick With Necessary Nitches For Fixing Switches, Regulators Etc And Fixing Of Exciting Wood Or Metal Box Using Nf Screw,Supplying And Fixing Polished Wood Board Made Out Of Not Less Than 15Mm Thick Planks At Both Sides With Planks Made Out Of Not More Than 2 Pieces And Fixing The Same To The Wall Using Tapered Wooden Plugs Screws Etc,Fabricating, Supplying And Mounting Ms Box Made Out 14 Swg Suitable For Foor/Wall Mounting, Fully Weather Proof With Provision For Better Heat Dissipation, Provided With Hinged Front Over Equipped With Temper Proof Locking Arrangements With Suitable Size Clamps With Necessary Cable Entry Pipe With Gland And Box Should Be Finished With 2 Coats Of Red Oxide Primer Paint And Finally Finished With Approved Colour Enamelled Metal Paint Etc., Complete,Labour Charges For Lowering Additional Gi Pipes Of Dia 32/50Mm Dia Including Transportation Charges (New Gi Pipe Required Will Be Supplied By The Department Free Of Cost & Released Gi Pipes Should Be Handed Over To The Department (Labour Chargesonly) Above 3 Lengths,Labour Charges For Lowering Additional Gi Pipes Of Dia 32 / 50Mm Dia Including Transportation Charges (New Gi Pipe Required Will Be Supplied By The Department Free Of Cost & Released Gi Pipes Should Be Handed Over To The Department (Labour Charges Only) Upto 3 Lengths,Labour Charges For Lifting Of Non Functioning Submersible Pump Set Along With Cable And Gi Pipes,Starter 20 Hp- Iso Certified,Starter 17.5Hp - Iso Certified,Starter 15 Hp - Iso Certified,Starter 12.5 Hp- Iso Certified,Starter 10Hp - Iso Certified,Starter 7.5Hp- Iso Certified,Starter 5 Hp - Iso Certified,Starter 4 Hp,Starter 3 Hp,Motor 5 Hp- Iso Certified,Motor 4 Hp- Iso Certified,Motor 3 Hp- Iso Certified,Non-Return Valve Assembly Complete With Rubber O Rings,Supply And Fixing Of Voltmeter,Supply And Fixing Of Ammeter,Supply And Fixing Of Led Indicator,Supply And Fixing Of Wiring Kit(Sd Upto 25Hp),Supply And Fixing Of Wiring Kit(Dol Upto 7.5Hp)(Mr),Supply And Fixing Of No-Volt (Nv) Coil,Supply And Fixing Of Terminal Plate (Connector 60A),Supply And Fixing Of Terminal Plate (Connector 30A)(Mr),Supply And Fixing Of Ryb Rotary Switch(Volt Selector),Supply And Fixing Of Single Phase Preventer(20 To 30 Hp),Supply And Fixing Of Single Phase Preventer(7.5 To 15 Hp) (Mr),Supply And Fixing Of 15 Amps Relay (Mr),Supply And Fixing Of 23 Amps Relay (Mr),Supply And Fixing Of 33 Amps Relay,Supply And Fixing Of 25 Amps Contactor,Supply And Fixing Of 16 Amps Contactor(Mr),Erection Of Panel Board & Ms Box (Outdoor Type) (Gulbarga Pred, Pg.No.57, Lt.No.12.2),Supplying And Fixing Angle Iron Frame Work Fabricated Out Of M.S. Angle Iron And M.S. Flat With Bolt, Washer Etc And Painted With 2 Coats Of Red Oxide And Then Two Coats Of Approved Paint 75X75x6mm (Pwd Ele Sr 2014-15, Pg.No.49, Lt.No.6.39.3),Refilling Available Earth Around Pipe Lines, Cable In Layers Not Exceeding 20Cms In Depth, Compacting Each Deposited Layer By Ramming After Watering With Lead Upto 50M And Lift Upto 1.5M Including Cost Of All Labour Complete As Per Specification Pre Sr 2011-12, P-3,1-6.,Labour Charges For Laying U.G. Cable Upto 3.5 Core 25 Sq.Mm As Per Pwd Electrical Sr 2010-11, P-68,1-1, Class A Pvc Cable,Lifting Of Struck Up Submersible Pump Set Above 300 Ft (Bwssb Sr 2017-18/O150g/Sl No.27),Lifting Of Struck Up Submersible Pump Set Upto 300 Ft (Bwssb Sr 2017-18/O150g/Sl No.26),Labour Charges Overhauling,Lifting Of Submersible Pumpsets,Re-Errection Charges Of Pumping Machinery Including Overhauling And Painting,Transportation Of Pumping Machinaries,Motor Base With Pin,Circlips(Small),Bearing (Gun Metal Bush) Centrifugal Cost Aluminium Bronze Bearing Bush,Studs And Nuts,Tip Carbon/Ferrode Padding,Thrust Bearing Block Assembly (Tb Bottom),Carbon Housing(Tb Plate),Lock Ring(Circlip Big),Lower Housing,Upper Housing,Lower Flange,Upper Flange,Labour Charges (Overhauling Of Pump Only),Brass Filter,Strainer,Cable Guard,Pump Coupling (Stainless),Pump Key (Stainless Steel) Upto 8 Stages,Pump Shaft (Stainless Steel) Counter Less Ground With Key Way Upto 8 Stages,Allen Screw,Steel Bush (I.D.O. Ss Sleeve),D.O. Bearing( I.D.O Lb Bush),Discharge Outlet (D.O.) Bearing(Lb Bush) And D.O Steel Bush(Ss Sleeve),Impeller Shell Moulded With Aluminium & Bronze,Guide Vane,Oil Seal Steel Bush(Oil Seal Sleeve),Oil Seal(Pump Oil Seal),Intermediate Piece (I.P.) With I.P. Leaded Bronze Bush,Pump Bowls,Rewinding Of Motor Of 20 Hp,Rewinding Of Motor Of 17.5 Hp,Rewinding Of Motor Of 15 Hp,Rewinding Of Motor Of 12.5 Hp,Rewinding Of Motor Of 10 Hp,Rewinding Of Motor Of 7.5 Hp,Rewinding Of Motor Of 5 Hp,Rewinding Of Motor Upto 3 Hp