Tender For Provn Of Acess Path And Hardstanding, Shed With Associated Work At Certain Locations At Af Stn Bihta.
Tender Value
48.26 Lakhs
Estimated cost
Bid Submission
18 Sep 2026
9 days left
EMD
96520
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Patna → Bihar
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Acess Path And Hardstanding, Shed With Associated Work At Certain Locations At Af Stn Bihta.
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil & spreading in surrounding area n exc 50 m distance complete, all as specified. |
| 2 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in SOFT/LOOSE soil complete, all as specified. |
| 3 | Excavation in trenches n. exc 1.5 m wide for foundations not exceeding 1.5 m deep and getting out in SOFT/LOOSE soil complete, all as specified. |
| 4 | Excavation in trenches n. exc 1.5 m wide for foundations exceeding 1.5 m deep but not exceeding 3 m deep and getting out in SOFT/LOOSE soil complete, all as specified. |
| 5 | Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete, all as specified. |
| 6 | Removal of excavated surplus spoil to a distance n. exc. 50m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified. |
| 7 | PCC type B-1 (1:2:4), using (20 mm graded stone aggregates) as in coping, kerb around chequered tiles and paver block, coping benching etc slightly rounded or chamfered incl form work , complete all as specified. |
| 8 | PCC type C-2 (1:3:6), using 40 mm graded stone aggregates as in foundation filling & mass concrete, complete all as specified. |
| 9 | PCC type D-2 (1:4:8), using (40 mm graded stone aggregates) as in foundation filling & mass concrete, complete all as specified. |
| 10 | Cement concrete, type B-1 (1:2:4), using 20 mm graded stone aggregates as in lintels over 1.5 metre clear span, cills, steps, seismic and other similar band, plinth courses, lacing courses , copings, kneelers, apex stones, bed plates, water troughs and the like complete all as specified. |
| 11 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in kitchen shelves and the like including necessary formwork complete all as specified. |
| 12 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates, as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified. |
| 13 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates, as in columns, pillars / post & struts complete all as specified. |
| 14 | Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified. |
| 15 | Use & waste of formwork to sides of pillars any type, posts, struts, piers, columns and stanchions with rough finished surfaces of concrete, complete all as specified. |
| 16 | Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished surfaces of concrete, complete all as specified. |
| 17 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 18 | Mild steel TMT bars 5 mm and over up to and including 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and binders complete all as specified. |
| 19 | Mild steel rolled sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to grade Fe-410-W Gde E-250, complete all as specified. |
| 20 | Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified. |
| 21 | Mild steel rolled sections as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to grade Fe-410-W Gde E-250, complete all as specified. |
| 22 | Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws comlete all as specified. |
| 23 | Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/cladding to wall, fixed with self tapping screws etc. complete all as specified |
| 24 | 50 mm thick, cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate, receive top layer, floors or similar locations, surface even and smooth with using extra cement complete all as specified |
| 25 | 75 mm thick PCC type C-2(1:3:6), using 40 mm graded stone aggregates even and fair without using extra cement, complete all as specified. |
| 26 | 100 mm thick PCC type D-2 (1:4:8), using 40 mm graded stone aggregates as in finished even & rough, as in sub floors, complete all as specified. |
| 27 | Factory made PCC chequered tiles, glossy finish, ISI Marked, with grey cement & pigment, 22-25 mm thick, of size 300 mm x 300 mm, in floors, over & including 20 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry complete, all as specified. |
| 28 | Granite ( colour and pattern as approved by GE) 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 20 mm thick (average thickness) cement mortar (1:4), complete all as specified. |
| 29 | 60 mm thick factory made chamfered edge, glossy finished cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete. |
| 30 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair using water proofing compound on walls in cement mortar (1:4), complete all as specified. |
| 31 | Two coats of cement base paint on new plastered wall surfaces, including preparation of surfaces, complete all as specified. |
| 32 | Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel & iron (new) surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified. |
| 33 | Supply, laying, jointing & testing of LT XLPE of sectional area 10 Sq.mm, 2 core insulated cable screened, bedded, galvanised steel strip or wire armourd cable (heavy duty) 1100 volt grade with aluminium conductor conforming to IS-7098 (Part-I -1988) laid in trenches/ ducts/ through pipes/ in floors / under roads/ hard standing /along poles and testing complete all as specified : |
| 34 | Clean dry sand ( locally available) as cushioning for under ground cable 230 mm thick (one layer of 80 mm thickness before laying the cable and other layer of 150 mm thickness after laying the cable) complete all as specified.NOTE:- Punned down thickness (over all 180 mm) shall be considered for measurement and payment. |
| 35 | Brick protection with Sub class 'B' bricks, laid flat and dry in trenches over the cable for protection as length perpendicular to the direction of cable adjacent to each other complete, all as specified. |
| 36 | Supplying , erecting and fixing steel tubular swaged poles with cast iron base plate of size 300mm X 300mm x 6mm final taper plug, bolts nuts & screws for type 410 SP-31 (9.0 mtr long ) including painting with two coats of aluminium paint over one coat of red oxide primer on all exposed surfaces and tarring with black bituminiouspaint to embedded portion in PCC and providing 3 Nos of 30 cm wide circular bands with black & yellow paint starting from plinth level at the gap of 30cm in between 2 band and numbering of poles, in yellow paint over black printedback ground at a height of 2m from bottom of pole with 5 cm large bold letters 2'' (inch) wide including taking down old unserviceable PCC poles of any type complete all as specified and directed.Note : Excavation , earth work , PCC in foundationand coping shall be measured and paid separately under relevent itme of this schedule |
| 37 | FRLS / HFFR PVC insulated unsheathed / sheathed cable with standard aluminium conductor 1100 Volts grade flat twin core service cable of size 1.5 sqmm confirming to IS:694/1990 with latest amendement ISI in the existing surface / recessed steel / PVC conduit completed all as specified and directed. |
| 38 | LED street light 45 watt outdoor type pressure die cast aluminium housing, heat resistant toughtened glass with frame and lamp with minimum efficiency 110 LM/W, IP 66 protection and making connections, completed all as specified and directed. |
| 39 | LED garden light white colour temperature 6500K LED type 10 watt 230 volts AC outdoor type with 360 degree indirect light IP 65 maple finish protection with impact and corrosion registant complete with driver with surge protection and lamp suitable for fixing on pipe 32/40/50mm completed all as specified and directed. MAKE: Crompton Cat No. LBLSN-10-CDL or equivalent in makes mentioned in Appendix 'B' |
| 40 | Weather proof PVC junction box made out of not less than 2mm thick of size 200mmx160mmx96mm (approx) complete with hinged door locking arrangment and consisting of 01 nos panel mounted connector 4 pole 16 Amp-01 No, MCB SP 6 Amp 10 kA -01 No, suitable size flanged type brass cable entry glands confirming to IP66 completed all as specified and directed. |
| 41 | GI earth strip of size 25x4 mm in ground not exceeding 40cm deep / fixing to wall / structure including earthwork and necessary insulators clamps, bolts, nuts etc complete all as specified. |
| 42 | Security light bracket made of 40 mm bore GI light grade pipe 1.5 metre long bend to shape including necessary welding to pole(s) or fixed with suitable size of flat iron clamps, nuts, bolts and washers etc. with & including two coats of synthetic enamel paint over a coat of primer complete all as specified |
| 43 | Nature switch astronomical distribution board complete 440v, 50 Hz with timer, contactor, relays in suitable metal enclosure of three phase integrated models of capacity 32 amp, + 10% voltage tolerance summer / winter timing set astro program active phase selection alternate mode with auto load changeover with non repetive shock and harmonic current emmision complete all as specified |
| 44 | Earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI strip 32x6 mm as earthing lead by means of GI or steel bolts/nuts/washers, protected by 15 mm bore GI light grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI light grade pipe for watering and including funnel, wire mesh, RCC cover, reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, using round bar, PGI funnel with wire mess & frame, PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in earthing pit including necessary excavation & earth work, , all as specified & shown in electrical plate No. 3 of MES Schedule Part – I.Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) The unit rate includes earthing lead & protection pipe upto 7.5 metre from top of earth plate.(iii) Earth resstance shall be less than 3 ohm. In case the test results are not found less than 5 ohm, complete earthing shall be redone by the contractor without any extra cost to Govt. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysSep 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender