Tender For General-Construction Of Gate Keeper Cabin And Allied Works At The Inner Gate Of District Jail, Kollam-Construction Of Gate Keeper Cabin And Allied Works At The Inner Gate Of District Jail, Kollam.-General Civil Work
Tender Value
1.41 Lakhs
Estimated cost
Bid Submission
10 Sep 2026
0 days left
EMD
3549
Bank guarantee accepted
Document Fee
555
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kollam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for General-Construction Of Gate Keeper Cabin And Allied Works At The Inner Gate Of District Jail, Kollam-Construction Of Gate Keeper Cabin And Allied Works At The Inner Gate Of District Jail, Kollam.-General Civil Work
BOQ
| Sl. No. | Item Description |
| 1 | Detailed estimate |
| 2 | 50.2.25.1:Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge |
| 3 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 4 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 5 | 4.2.3:Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | 50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete |
| 7 | 13.4.2:12 mm cement plaster of mix:1:6 ( 1 cement : 6 coarse sand) |
| 8 | 21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 9 | 21.3.2:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm) |
| 10 | 10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 11 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 12 | OD65790/2026-2027:Providing and fixing precoated galvanized iron plain sheets (as approved by the Engineer-in-charge) 5-7 microns epoxy primer on both sides. of the sheet should be supplied in single length up to 12 m or as directed by Engineer-in-charge. The sheet shall be fixed using self-driving/self-tapping screws, complete up to any pitch in horizontal/vertical or curved surface, including cutting to size and shape wherever required. |
| 13 | OD65791/2026-2027:Providing Alu-zinc coated 0.35 mm thick GI trafford sheet of approved quality roofingincluding vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mmdiameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with whitelead, including a coat of approved steel primer and two coats of approved paint onoverlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shapewherever required |
| 14 | OD65794/2026-2027:Providing and fixing 3 mm thick UV Board decorative sheet in panelling fixed in aluminium doors, windows shutters and platforms frames with C.P Brass/ Stainless steel screws etc. complete as per architectural drawings and directions of Engineer in charge. UV Board decorative sheet. |
| 15 | OD65795/2026-2027:Providing and fixing steel slider set (0.50 m long) for table draws, keyboards etc. including labor, conveyance. |
| 16 | 9.79.3:Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.65 mm |
| 17 | OD65796/2026-2027:Supplying and fixing stainless steel auto closer hinges |
| 18 | OD65797/2026-2027:Supplying and Fixing Round PVC Cable manager including all labour, conveyance etc. all |
| 19 | 9.165.3:Providing and fixing bright /matt finished Stainless Steel handles of approvedquality & make with necessary screws etc all complete.75 mm |
| 20 | 21.5:Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ). |
| 21 | OD65798/2026-2027:Providing and fixing false ceiling with 7.5 mm thick PVC plain panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete (aluminium frame work shall be paid separately) |
| 22 | OD70000/2026-2027:Supplying Nilkamal Contract 01 with Arm Visitors chair (Black) including all labour, conveyance etc. |
| 23 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 24 | OD65792/2026-2027:Engaging blacksmith |
| 25 | OD65793/2026-2027:Engaging mancoolie Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodaySep 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender