Tender For Addition/Alteration And Special Repair To Certain Jcos/Or Md Accn At Barrackpore Mil Stn Under Ge Barrackpore
Tender Value
8.15 Crore
Estimated cost
Bid Submission
25 Sep 2026
15 days left
EMD
7.33 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
24 Paraganas North → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration And Special Repair To Certain Jcos/Or Md Accn At Barrackpore Mil Stn Under Ge Barrackpore
BOQ
| Sl. No. | Item Description |
| 1 | NOTE (Applicable for all items) :-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.2. It is highlighted that the certain condition of General Condition of Contracts (IAFW-2249) has been modified as per direction of MoD i.e. inclusssion of Performance Security, deletion of Risk & Cost Provisions and increase in defect liability period all as per tender documents. The tenderers should keep in mind while quoting their offer. |
| 2 | Taking down Chowkats or Frame (without taking off shutter from the frame) exc. 1.50 SQUARE METRE but n exc 4.00 Sqm each complete all as specified and as directed. |
| 3 | Taking down Chowkats or Frame (without taking off shutter from the frame) n exc. 1.50 SQUARE METRE complete all as specified and as directed. |
| 4 | Taking down rusted steel windows/Ventilators of any description and size incl shutters complete all as specified and as directed |
| 5 | M & L for Pressed steel frames of size 125 X 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed |
| 6 | All as per item No above but frame size 105 X 60mm. |
| 7 | S/F 2nd class Hard wood plain solid straight Chowkatsand frame wrought framed rebated on the solid rounded or chamfered put together with shine pinned at joints supply and fitted complete all as specified and as directed. |
| 8 | S/F 25 mm thick flush shutter solid core construction, with block board core and plywood face panels commercial type on both side with particle board complete all as specified and as directed. |
| 9 | S & F 35mm thk Flush shutters, solid core construction, with particle board core and plywood face panels, commercial both face is covered with decorative face veneer with lipping/frame to match type on both sides. |
| 10 | S&F 35mm thick 2nd class hard wood plain framed pannelled shutter (three panel) with lock rail and panel of 12mm veneered board particle board of exterior grade with commercial veneering on both faces. The size of rail and style complete all as directed. |
| 11 | S/F 35 mm thick factory made 2nd class hard wood glazed and skelton shutter open nrebated and prepared to receive glass gauze etc (without shas bar) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of numbers of shutter as specified in SSR Pt I Section 8, clause 8.2 (a) complete all as specified and as directed. |
| 12 | Refixing Shutter of any description n exc 1 sqm each as same opening incl taking down easing and adjusting and also refixing builders hardware as reqd incl renewal of unserviceable screws etc. |
| 13 | Refixing Shutter of any description exc 1 sqm but n exc 2 sqm each as same opening incl taking down easing and adjusting and also refixing builders hardware as reqd incl renewal of unserviceable screws etc. |
| 14 | S & F for Powder Coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing for Powder Coating etc. complete all as specified complete all as spacified |
| 15 | S & F Powder Coated for anodised aluminium window and ventilator sliding shutters without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) for powder coating of any colour (thickness or powder coating not less than 50 micron etc. complete all as specified |
| 16 | S&F for sheet glass 5.50 mm thick ordinary quality and glazing with ail putty in squares n exc 0.5 Sqm each pane complete all as specified. |
| 17 | S&F solid PVC door frames of size 50mm x 47mm made out of 5mm plain cover fillet colour PVC sheet reinforced with MS square tube for toilet. |
| 18 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing |
| 19 | M&L PCC (1:2:4 ) type B1( using 20 mm graded aggregate ) used as in filling of hod fast |
| 20 | Mild Steel Flat Iron as in Holdfast of size 25 x 3 mm thick of Fe 290 Gde-E-165 complete all as specified and as directed. |
| 21 | S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in window and door as fixed in repair as old door/window. |
| 22 | Ditto all as per item No above above but pinheaded |
| 23 | S/class hard wood small fittings such as shaped door and window stops and the like incl all necessary labours articles not exceeding 200 Cu cm each complete all as specified |
| 24 | Supply & Fixing mild steel MS butt hinges 50 mm medium weight cold rolled for doors and windows stopers etc complete all as specified and directed |
| 25 | S/F 100 mm long Butt Hinges Medium Weight, Cold Rolled mild steel and fixed complete all as specified and as directed. |
| 26 | S/F 75 mm long Butt Hinges Medium Weight, Cold Rolled mild steel and fixed complete all as specified and as directed. |
| 27 | S&F for 200 mm aluminum , anodised, barrel tower bolts of extruded section. |
| 28 | S&F for 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed. |
| 29 | S&F for 150 mm Extruded aluminium alloy handles, fabricated type, anodised |
| 30 | S & F 100 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 31 | S/F 125 mm long Hasp and staple Aluminium safty type stove enamelled black incl bolt to hinge plate and fixed with screws complete all as specified and as directed. |
| 32 | M & L for helical door spring 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete |
| 33 | S&F for 250mm aluminum alloy, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed. |
| 34 | S & F in repair curtain rod of aluminium alloy 20 mm dia with fixing brackets, stops, rollers etc all as specified and as specified. |
| 35 | M/L appying two coats Synthetic Enamel Paint over a coat of pink primer on wooden surface any description over 10 cm in width or girth not otherwise described including preparation complete all as specified and as directed. |
| 36 | Preparation of new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 37 | Surface Preparation: Clean all concrete surfaces free of laitance, dust, dirt, cavities, projecting nibs etc.by grinder and wire brush. Grease should be cleaned using a chemical degreaser and washed with clean water and allowed to dry. Remove all protrusions from concrete surfaces using a fine hair broom finish. Remove moss and lichen manually and treat the surface with a fungicide. Wash the surface thoroughly with clean water and allow it to dry. Standing water must be removed to prevent subsequent compromise of waterproof properties. For undulation of the existing slab shall be rectified with Shrinkage controlled, polymer modified, fibre reinforced cementitious repair mortar Renderoc SP40. Provide and Apply single coat of Lime mortar shall be applied at 1:3 ratio (Lime : sand) admixed with SBR based compound with 5-9 Liters Nitobond SBR Latex for additional layer of waterproofing, repair the covings, pot holes and any unevenness on Lime terrace roof. All around on the roof, at the parapet wall junction, an angular fillet of 50 mm X 50 mm. Free flow recision grout Conbextra GP2 poured within the leak-proof form work in accordance with the mix ratio as recommended in the technical data sheet of the manufacturer and then be sealed with an epoxy putty NITOCOTE VF. The surface is rendered to give aesthetic & visual surface finish. |
| 38 | Providing and carry out waterproofing treatment to sound, moisture free concrete surface using Nitoproof 600PF - Liquid applied single component pitch free polyurethane coating capable of bridging substrate cracks upto 2 mm. System includes proper surface preparation to remove loose dust, dirt, loose mortar, curing compound etc., and application of Nitoproof WB Primer, Water dispersible epoxy primer followed by two coats of Nitoproof 600PF coverage @ 2.0 kg/m2 to achieve 1.5 mm WFT in two coats followed by laying of separation layer of 120 gsm non-woven geotextile layer before carry out protection screed etc. complete including all tools and tackles as per manufacturer’s specification. Nitocote 600PF cured material shall be having crack bridging of 2 mm, Elongation (ASTMD 412) – 500 - 700 %, Tensile Strength (ASTM D412) – 2.5 N/mm2, Recovery from Elongation (ASTM D412) – 95 %, 85% Solid Content, Tear Resistance (ASTM D624) – 15 Kn/m, Shore A Hardness (ASTM D2240) – 60, Water vapour transmission- 0.6 g/m2/hr, Water Permeability @ 5 Bar (BS EN 12390)-Nil, Service Temperature – -40°C to 70°C, Flash Point > 70 °C,Viscosity-60p, Specific Gravity-1.5. The item rate shall be including of all kinds of labour, tools & tackle, machineries, lead & lift, mathadi charges, curing, wastages, consumable, cleaning, shifting of debris outside the site premises etc. complete as per design, drawing & instructions of EIC. Cost of 120 gsm non-woven geotextile and 75mm Screed concrete shall be paid separately. |
| 39 | Supply & Laying Geotextiles of 120 Gsm over the waterproofing coating to avoid damage during screed casting. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by EIC. |
| 40 | Supply & laying of maximum 25 mm thick (at RW outlet) protective screed/Plaster over the waterproof coating at proportion of 1:2:4 admixed with suitable integral waterproofing compound conforming IS 2645:2003 @ 200ml per bag of cement and reinforced with PP fibres with proper slope towards RW pipes. Green stage saw cutting on the screed will be done in panels (3mt X3mt) with a groove size of 10mm X 15mm. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by EIC. |
| 41 | Taking down cement plaster on brick or stone or concrete surfaces of wall etc , icluding raking out joints , hacking for key, scrubbing down with water etc. |
| 42 | Supply only liquid water proofing compound |
| 43 | Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and removing rubbish off the premises. |
| 44 | S&F for non skid ceramic coloured tiles of 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc with 20mm thick screed bed or bedding layer of mortar for laying floor finishes in cm 1:6, set and joint free non skid tiles in neat cement slurry and pointed in coloured cement |
| 45 | All as per item No above but in skirting including 10mm thick plastering for backing coat in cement mortar 1:3 |
| 46 | S&F Non skid ceramic coloured tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc with 20mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6), set and jointed in neat cement slurry and pointed in coloured cement |
| 47 | S&F Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering or bedding layer of cement mortar (1:3) for vertical surfaces |
| 48 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etclaid and pointed in any type of mortar |
| 49 | S&F for 20mm thk Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 15 mm thick cement screed base in CM (1:3) |
| 50 | M&L for Machine cut Kota stone slab flooring 20-25 mm thick over 20 mm thick cement screed base in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. |
| 51 | M&L for Machine cut Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry over 10 mm thick cement plaster in CM (1:3) including rubbing and polishing complete. |
| 52 | Demolition of Cement concrete in ground floors and pavings n exc. 15cm thk (below or above ground level) complete all as specified and as dircted. |
| 53 | M & L for PCC with type D-2 1:4:8 (40 mm graded aggregate ) 75 mm thick as in sub base. |
| 54 | M & L PCC 1:3:6 type C2 75 mm thick (using 40mm graded aggregate) as in plinthprotection finished the concrete surface even and smooth W/O using extra cement complete. |
| 55 | M & L 40mm thick cement concrete 1:2:4 (Using 20mm graded stone aggregate) as in floor finished even and smooth using extra cement complete all as specified and as directed. |
| 56 | M & L for 25mm thk Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) for laying of floor tiles |
| 57 | M & L 3mm thick glass dividing strip wide 38 mm inserted in position as in floor complete all as specified and as directed. |
| 58 | M & L for outdoor endura floor tiles of size exc 0.11 Sqm but n exc 0.22 Sqm, thickness 9-10mm of set, jointed and pointed in neat cement slurry in floor,laid over and incl 15mm thick cement screed base in CM 1:4, complete all as spd |
| 59 | Demolition of Brickwork or stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement morter |
| 60 | Material and labour for brickwork in cement mortar 1:6 withsub class `B' bricks straight orcurved on plan exceeding 6mmean radius with old size bricksas in walls all as specified. |
| 61 | M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4). |
| 62 | M&L for rendering 15mm thick on fair face of brick works or concrete surfaces of walls with CM (1:6) and finished even and smooth without using extra cement. |
| 63 | M&L for rendering 15mm thick on other than fair face of brick works or concrete surfaces of walls with CM (1:4) and finished even and smooth without using extra cement with WPC @100 ml per 50 kg of cement or all as per manufatucring Instruction. |
| 64 | M&L for rendering 5mm thick in CM 1:3 to fair face of brick works or concrete surfaces of ceiling surfaces . |
| 65 | M&L for applying two coat of distemper oil emulsion after preparation of old plastered surfaces of wall over a coat of Chalk whiting on plastered surfaces, preparatory to distempering |
| 66 | M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces |
| 67 | M&L for two coat of oil bound distemper over a coat of alkali resistant cement primar newly plastered ceiling including preparation of surface complete all as specified and as directed |
| 68 | M&L for preparation of old decorated plaster surfaces of wall and applying one coat of oil bound distemper . |
| 69 | M & L for Complete removal of existing wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gms/litre and UV resistance as per IS 15489 : 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shadeICompany Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over old surfaces. |
| 70 | M&L for preparation of old decorated surfaces on ceiling inciuding stopping nails, holes ,filling the cracks and apply one coat of oil bound distemper . |
| 71 | M&L for preparation of old painted wooden surfaces exc 10Cm width or girth and apply one coat of synthetic enamel paint. |
| 72 | M&L for preparation of old painted steel surfaces exc 10Cm width or girth and apply one coat of synthetic enamel paint. |
| 73 | Taking up or down steel tubing and connections for 15mm bore of pipe all as directed. |
| 74 | Re-fixing for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors etc) |
| 75 | S&F for 15mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors , wall etc ( surface or concealed type) all as specified and directed. |
| 76 | Taking up or down steel tubing and connections for 20mm bore of pipe all as directed. |
| 77 | Re-fixing for 20mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors etc) including cleaning, re-fixing the old screw threads etc complete all as specified and directed. |
| 78 | S&F for 20mm dia Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed. |
| 79 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar for 100mm bore pipe . |
| 80 | S&F for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 81 | S&F for 110mm bore PVC (SWR) bends any radius. |
| 82 | S&F for 110mm bore PVC (SWR) bends any radious provided with access door . |
| 83 | S&F for 110mm bore PVC (SWR) junction single, (Single T) equal or unequal provided with access door . |
| 84 | S&F for 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal provided with access door . |
| 85 | S&F for 110mm bore PVC (SWR) branch piece, double (double Y) equal or unequal provided with access door . |
| 86 | S&F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 87 | S&F PVC (SWR) bends of radius 75mm bore . |
| 88 | S&F PVC (SWR) bends with access door of radius 75mm bore . |
| 89 | S&F PVC (SWR), junction single, (Single T) with access door equal or unequal 75 mm bore. |
| 90 | S&F PVC (SWR) vent cowl 75mm bore. |
| 91 | S & F in repair PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement |
| 92 | S&F in rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position as specified of 1000 litres capacity including dismanting the existing tanks. |
| 93 | S&F in rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position as specified of 500 litres capacity including dismanting the existing tanks. |
| 94 | S&F in repair 20 mm Ball valves Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed |
| 95 | M & L for Disconnecting existing tanks of capacity exc 250 but n exc. 500, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measuredseparately) |
| 96 | M & L for Cleaning and removing all scale and dirt, etc, from water tanks of cap exc 250 but n exc 500 ltr and from mouths of circulating pipes, etc |
| 97 | S&F in repair for vitreous china wash down water closet pan (pedestal pattern) white with 'P' or 'S' trap type (excluding flushing cistern & flush pipe) including connection to trap & to flushing pipe, anti-syphonage pipe out in complete as in repair including making good to floor complete all as specified and directed. |
| 98 | S&F in repair for PVC water closet seat, white/black colour as required, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device as in repair complete all as specified and directed. |
| 99 | S&F in repair for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor as in repair complete all as specified and directed. |
| 100 | S&F Vitreous China wash basin, white, flat back, size 580 X 450mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand complete incl 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end. |
| 101 | S & F Pillar cock 15mm bore fancy type chromium plated, screwed down high pressure with or without lettered HOT or COLD with long screwed and fly-nuts screwed for iron pipe or brass ferrule and fixed in repair complet all as specified and as directed. |
| 102 | S&F in repair for 15 mm Bib taps fancy type Chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed . |
| 103 | S&F in repairs 15mm bore angular stop valve fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and directed. |
| 104 | S&F in repairs 15mm bore angular stop valve but fancy type, chromium plated with long shank and cup chromium plated (Concealed type) screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and directed. |
| 105 | S & F in repair 15mm bore Brass Chromium plated shower roses of 125mm size with or without swivel joints, any size, including CP Shower arm 195mm long fixing to steel pipe or union |
| 106 | S&F health faucet fixed to EWC with 1mtr long easy flexible tube of 8mm dia and wall hook complete all as specified and directed. |
| 107 | S&F in repair 600 mm x 450mm 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 108 | S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as directed |
| 109 | S&F PVC connections 15mm size with PTMT nuts of length 450mm. |
| 110 | S&F in repair Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges |
| 111 | S & F HDPE waste pipe of 32mm dia pressure rating 6 Kgs/Sq cm fixed complete to walls floors etc. |
| 112 | S&F in repair Sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160m |
| 113 | S&F Stainless steel plate rack (0.63 mm thick s/s sheet) of size 775 X900 X 250 mm fixed in wall with Stainless steel screw of suitable size complete all as specified and directed. |
| 114 | Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 115 | S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 116 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering |
| 117 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 118 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 119 | Dismantling framed timber scantlings 40 sq. cm and over in section, in any position |
| 120 | S&F MS work ( MS angle ) as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat section or tubular sections) including distance pieces, cleats etc etc including necessary cutting, welding etc complete Fe-410 w gde E-250 quallity A. |
| 121 | Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets |
| 122 | S&F 605X605mm grid anodised aluminium snap grid frame work for false ceiling, providing and fixing 4mm Non asbestos fibre cement building boards fixed or laid in aluminium frame work and including three coats of white washing in ceiling complete all as specified |
| 123 | S & F of 18mm thick UV coating, HDHMR board exterior grade, including acrylic high gloss sheet of 3mm thick over HDHMR board,anti fungal,moisture resistence,anti borer, as per IS 14587 for frame and shutter for kitchen cabinets/Cupboards etc. complete all as specified and directed by Engr-in-charge. NOTE:- Sample as approved by GE. Make:-Action tessa/Greenply/ Century |
| 124 | S & F Partial overlay / fully overlay hydraulic self closing concealed hinges having size 103mm x 64mm finish of nickel/silver complete all as specified and directed by Engg-in-charge. Make : Godrej Kitchen appliances or other equivalent make as approved by GE. |
| 125 | S & F stainless steel cabinet / drawers handle having a length of 250mm and shape complete all as specified and directed. |
| 126 | S & F stainless steel modular thali-plate basket SS 304, size of 520x485x200mm,heavy duty and grade steelwith finish of zinc, corrosion resistance telescopic drawer channel having weighing capacity of 25 kg complete all as specified and directed. Godrej Kitchen appliances or other equivalent make as approved by GE.. |
| 127 | S & F stainless steel modular perforated cutlery basket SS 304 size of 520 x 485 x 10 cm with heavy duty and grade steelwith finish of zinc, corrosion resistance telescopic drawer channel having weighing capacity of 25 kg complete all as specified and directed.Godrej Kitchen appliances or other equivalent make as approved by GE.. |
| 128 | S & F stainless steel glass tray plate tray having length of 610mm, corrosion resistance telescopic drawer channel complete all as specified and directed. Godrej Kitchen appliances or other equivalent make as approved by GE. |
| 129 | S & F stainless steel grain trolley SS 304 having size of 525x485x350mm, with heavy duty and grade steelwith finish of zinc, corrosion resistance telescopic drawer channel having weighing capacity of 25 kg complete all as specified and directed. Godrej Kitchen appliances or other equivalent make as approved by GE. |
| 130 | Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for |
| 131 | Providing water proofing treatment to RCC sunken slab as specified and directed as under:-(i) Demolished the existing damaged concrete from sunken portion carefully upto RCC slab including taking out of water closet and traps etc (depth approx 400mm, and area not less than 2.00 Sqm)(ii) Cleaning the existing RCC sunken slab and vertical wall/RCC beams as per direction.(iii) 15mm thick plaster over the flat & vertical surfaces in CM (1:4) mixed with WPC @200ml per 50 Kg of cement as per manufacturer's instructions(iv) Applying two coats of elastomeric acrylic water proof coating using rooler, each coat of elastomeric acrylic compound required 6-8 hrs to dry, 2nd coat shall be applied on fetting the first coat complete dry consumption of materials shall be as per manufacturer's instructions.(v) Filling the sunken portion with PCC (1:5:10) type E2 (using 40mm graded stone aggregate).(vi) After complete treatment of RCC sunken portion same shall be tested with 24 hrs ponding test, to observe the leakage and seepage from RCC portion. |
| 132 | Dismantling removing all unsound concrete, plastered material by chipping/chiseling gently at all effected and adjoining areas of concrete etc till sound surface is reached all various locations in building (upto 4 storied) subsequently cleaning the surfaces by hair brush and air blower and removing rubbish off the premises and disposing at the dumping site as approved by local authorities including hoisting assembling and fixing of double layer steel scaffolding to external perimeter of building complete all as specified and directed. |
| 133 | Removing of concrete all around reinforcement bar upto 12 mm dia and over from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiseling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area thoroughly by water and allow it to dry and totally rust free of reinforcement bar all as complete as per manufacturer's instruction as specified (upto 4 storied bldg). Make( Rust removing chemical):- Reebaklens RR of FOSROC or equivalents solutions SIKA/STP. |
| 134 | Material , labour and preparation of existing reinforcement surface by brush and application of two component epoxy zincnch primer on existing reinforcement surface of minimum specific gravity 1.75, ad_hesIve bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litre. complete all as specified (upto 4 storied bldg). Make- Nitozinc primer of FOSROC or equivalents. |
| 135 | Material and labour for introducing new reinforcement bars upto 12 mm dia and over for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc all as specified.(upto 4 storied bldg) |
| 136 | M&L for supply, mixing and placement of micro-concrete cement based prepacked single component chloride free, sulphate free, non-shrink, free flow. elf compacting, ready to use after mixing water in specified proportion of Sika Rep Microconcrete-4 or renderoc-RG of Fosroc in required thickness as per manufacture's instruction and all as directed. Compressive strength (ASTN C 109,cm cube) of 35 MPa at 28 days including application curing compound concrete WB manufactured by Fosroc of equivalent at various locations in Bldgs including necessary form work complete all as per manufactures specification. |
| 137 | M & L for applylng of high efficiency polymorlc resin base film forming curing ogont/comroIind over cnncroto Hurfoco nnd maximum coverage area 5.00 Sqm per litre asror mcmurocturorn Instruction complete all as specified & directed. |
| 138 | Material & Labour for applying Anti carbonation coating as per manufacturer's specification of approved brand, manually using brushes on the hardened concrete/plastered surfaces after cleaning the surface and removing all loose particles, deposits etc complete including one coat of primer and two coats coatings as directed. |
| 139 | Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required |
| 140 | Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along externalwall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete |
| 141 | Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty at necessary holes for smooth finishing complete all as specified and directed complete all as specified and directed. Please Enable Macros to View BoQ information |
| 142 | Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty at necessary holes for smooth finishing complete all as specified and directed complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender