Tender For Construction Of Degree College, Mandu, Ramgarh Under Mandu Legislative Assembly In Ramgarh District Under Vinoba Bhave University, Hazaribagh
Tender Value
Ref. Documents
Estimated cost
Bid Submission
18 Sep 2026
18 days left
EMD
38.36 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ramgarh → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Degree College, Mandu, Ramgarh Under Mandu Legislative Assembly In Ramgarh District Under Vinoba Bhave University, Hazaribagh
BOQ
| Sl. No. | Item Description |
| 1 | Clearing grass and removal of rubbish up to a distance of 50 meters outside the periphery of the area |
| 2 | Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I |
| 3 | Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B) |
| 4 | Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume). |
| 5 | Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge (Mode of measurement compacted volume) |
| 6 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Hard rock (requirin g blasting). |
| 7 | Earth filling of available earth by mechanical transport including loading, transporting, unloading ground for lead upto 1 km for all lifts, complete as per directions of Engineer-in-charge. |
| 8 | Earth filling of available earth by mechanical transport including loading, transporting, unloading ground for lead upto 2 km for all lifts, complete as per directions of Engineer-in-charge. |
| 9 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 10 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor. With Chlorpyriphos EC 20% with 1% concentration |
| 11 | Providing designation 75A one brick edge soling joints filled with loca] sand including cost of watering taxes royalty all complete as per building specification and direction of E/l. |
| 12 | CONCRETE WORK |
| 13 | Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 14 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 15 | Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting In position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. |
| 16 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size) |
| 17 | Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size) |
| 18 | R C C WORK |
| 19 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 20 | Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillers, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcemnet. |
| 21 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of layinh but excluding the cost of centering ,shuttering finishing and reinforcement including admixtures in recommended proportions as per IS : 9103 to accelerate rated srtting of concrete, improve workability without impaiting strenth and durability as per direction of engineer in charge (note :- Cement content considered in this item is 330 kg/cum excess/ less cement used as per design mix is payable/ recoverable seperataly ). |
| 22 | All works uptp plinth level |
| 23 | All works above plinth level upto floor V level -M25 |
| 24 | Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 25 | Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 26 | Add for using extra cement in the items of design mix over and above the specified cement content therein. |
| 27 | Providing Tor steel reinforcement of 8mm. dia.TMT rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 28 | Providing Tor steel reinforcement of 10mm,28/32mm dia. TMT rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 29 | Providing Tor steel reinforcement of 12/16mm. & 20/25mm. dia. TMT rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 30 | Centering and shutteing including struting, propping etc and removal of form for Foundations, footings, bases for columns, etc for mass concrete |
| 31 | Centering and shutteing including struting, propping etc and removal of form for Walls ( any thickness) including attached pilasters, butteresses, plinth and string course etc |
| 32 | Centering and shutteing including struting, propping etc and removal of form for Suspended floors, roof , landings,balconies and access platform |
| 33 | Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) |
| 34 | Centering and shutteing including struting, propping etc and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 35 | Centering and shutteing including struting, propping etc and removal of form for Columns, Pillars, Piers, abutments, Posts and struts |
| 36 | Centering and shutteing including struting, propping etc and removal of form for Stairs, ( excluding landings ) expept sprial staircase |
| 37 | Centering and shutteing including struting, propping etc and removal of form for Vertical and horizontal fins individuaaly or forming box louvers band, facies and eaves boards |
| 38 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of1 metre or part thereof (Plan area tobemeasured).suspended floors, roofs, landing, beams and balconies (Plan area to be measured) All floors slabs:( floor to floor Ht 3.6 m) |
| 39 | BRICK WORK |
| 40 | Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I. |
| 41 | providing designation 75 B brickwork in C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l. |
| 42 | Providing designation 75A brickwork in CM (1:3) in superstructure with approved quality of clean coarse sand of FM 2 to 2,5 including providing 10mm thick mortar joints , cost of screening, materials, scaffolding, raking out joints to 15mm depth curing, taxes and royalty all complete as building specification and direction of E/I |
| 43 | Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 44 | Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I. |
| 45 | Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9\\"x4.5\\"x3\\") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 46 | Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 47 | Providing designation 112 mm thick reinforced designation 100 A brick work vuith fly ash lirne brick (FLAG)confirming to lS 12894-1990 (9\\"x4'5\\"x3\\" ) in C.M. ( 1 . 4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials,n caffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specificationand direction of E/|. |
| 48 | Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary |
| 49 | WOOD WORK |
| 50 | Supplying, fiiting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors windows skylights fanlights and C/W celetial window opening including wedge over all clamps complete including application of two coats of wood preservative of approved quility onthe surface buttling walls and lintels all complete as per building specification anddirection of E/I. |
| 51 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately |
| 52 | Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutter door and windows with black board core blended with high quality phenol formal clehydes synihetic resin both side commercial veneered of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l. |
| 53 | Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l. |
| 54 | Supplying fitting and fixing 35mm thick solid core type decorative double leaf flush door sltutter with both side decorative veneered with black board core bended with high quality phenol formal clehydes synihetic resin of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l. |
| 55 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conformingto IS : 2046 Type S, including cost of adhesive of approved quality.1.0 mm thick |
| 56 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 45 x 70 mm |
| 57 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/ mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25 mm thick |
| 58 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm |
| 59 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 60 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper |
| 61 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 62 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness |
| 63 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 64 | Providing and fixing S.S. sliding door bolts (aldrop) with nuts and screws etc. complete: |
| 65 | 250x16mm |
| 66 | 300 x 16mm |
| 67 | Providing and fixing SS sliding tower bolt with required fastners (Screws) complete: |
| 68 | 250x10 mm |
| 69 | 600 mm |
| 70 | Providing and fixing SS handles \\"D\\" type with required fastners (Screws) complete: |
| 71 | 250x19 mm (Pipe dia) |
| 72 | 200x19 mm (Pipe dia) |
| 73 | Providing and fixing SS hanging floor door stopper with necessary screws etc.complete: 150 mm Rubber Stopper |
| 74 | Providing and fixing SS door latch with necessary screws etc. complete. 250x12 mm |
| 75 | Providing and fixing SS sliding baby latch with required fastners (Screws) complete: 100 x 10 mm |
| 76 | Providing & Fixing Wall mounted door Buffer |
| 77 | Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately). |
| 78 | Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately). |
| 79 | Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. |
| 80 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with all acesories (handle, lock, door closer, stopper etc. as per dwg) |
| 81 | STEEL WORK |
| 82 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 83 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M .S. tube |
| 84 | Supplying,fitting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved design and drawing, properly fabrlcated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/1 |
| 85 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 86 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating not less than 275 gm/m² |
| 87 | Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. |
| 88 | FLOORING WORK |
| 89 | providing and laying, Doublecharge vitrified floor tiles in different sizes (thickness to be specified by lhe manufacturer) with water absorption less than 0.08% and conforming to lS 15622/ISO 13009 of approved make in all cotours and shades, laid on 20mm thick cement mortar 1 4 (1 cement:4 coarse sand) jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of tile 600x600 mm |
| 90 | Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 SQM |
| 91 | Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 92 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 93 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade |
| 94 | Providing and laying 1st quality Ceramic glazed wall tiles thickness to be specified by the manufacturer) in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing polishing and cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 95 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 96 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1 : 3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specificaton and directon and E/I. With commercial grade colour tiles |
| 97 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with Udaipur green marble |
| 98 | Green stone 20 -25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 99 | Providing and laying 25mm. thick kotah stone slab flooring of approved size, texture and colour over 19 mm thick base of lime morter (1:l:1) ( Lime putty : surkhi: coarse sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size. |
| 100 | Providing and laying 25mm. thick kotah stone riser of steps, skirting and pillers of approved size, texture and colour over 12 mm thick cement morter (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size. |
| 101 | ROOFING & WATER PROOFING WORK |
| 102 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase |
| 103 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 104 | Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :- |
| 105 | (a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete. |
| 106 | (b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured.\\" |
| 107 | (c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl.\\" Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal |
| 108 | (d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be charrmfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface slrould be packed properly with rich concrete and the peripheral mouih to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose ofrreasurement the entire treated surface will be measured.\\" |
| 109 | (e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years. |
| 110 | Covering of treated surface wrth PCC :- Providing 50mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr |
| 111 | Providing and mixing Liquid lntergral water proofing compound in Conctrete or plaster as per rnanufacturer specificatioqand as per cjirection of Eng - in Charge Brand- Sika Plastocrate plus, MYK proof WP 1 0, Fosroc-Cc.rnplast X4211 C, Dr fixit Pidiproof LW+ or Equivalent |
| 112 | Providing and filling of 6 mm groove between 50mm PCC panels with 6 mm thick deep thermocol strip and filling the rest 25mm with polysulphide sealant (poring grade)as per drawing and technical specification and direction of E in charge (with 18 % GST ). Brand:- sika - polysulshide,fosroc- thioflex 600, dr fixit pidi seal PS (42P) ,MYK seal PS or euivalent. |
| 113 | Toilet/Kitchen Water proofing: |
| 114 | 1) Surface preparation by grinding machine, cleaning , crack filling etc. complete |
| 115 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : |
| 116 | (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. |
| 117 | (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry |
| 118 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm |
| 119 | Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage. |
| 120 | FINISHING WORK |
| 121 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I. |
| 122 | Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 123 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 124 | Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I. |
| 125 | Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% or any approved water proffing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 126 | 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) |
| 127 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 128 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. |
| 129 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM |
| 130 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 131 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 132 | Providing two coats of oil bound distemper of approved shade and make ov er a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with purnice stone or fine sand paper applying putty taxes all complete as per building specification and direction of E/I. |
| 133 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 134 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per bullding specification and direction of E/l. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification). |
| 135 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per bullding specification and direction of E/l. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification). |
| 136 | Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/l. |
| 137 | ALUMINIUM & GLASS WORK |
| 138 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately): For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 139 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 140 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4 mm thickness (weight not less than 10 kg/sqm) |
| 141 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid .in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 142 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading |
| 143 | Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600 Upto 10 mm depth and 10 mm width |
| 144 | Providing and fixing factory made upvc glazed/wire mesh window/ door comprising of lead free upvc multi -chambered frame, sash and mullion/ coupler (where ever required ) extruded profiles having minimum wall thickness of 1.70 mm series R1 and R2 profiles and 2.10 mm for series R3 and R4 profile confirming to EN 12608 in any shape colour and design duly reinforced with galvanized mild stell section made of required shape & size as per CPWD specification upc extruded glazing beads interlock and inline sash adaptor (where ever required ) of appropriate dimansion, EPDM gasket, hardwere, SS 304 grade fastners of minimum 8 mm dia with countersunk head comprising if matching polyamide PA6 IS 1367 Part 1 to 14 plastic packers plastic caps and nacessary stainless steel screws etc. profile of frame sash & mullion (if requred ) shall be mitred cut and fusion welded/ mechanically jointed duly sealed at all corners inculding drilling of holes for fixing hardware and driange of water etc. after fixing frame the gap between frame and adjaent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quility, all complete as per approved drawing confirminh to cpwd specification & direction of engineer in charge. section of steel reinfocement and cross sections of upvc profiles to be as per design approved by engineer in charge. wire mesh/ glazing of plain/ toughened /laminated/ double glass unit with / without high performance coating as per design requirements and confiming to IS 3548 & IS 16231 shall be paid separately. |
| 145 | Note:- structural design proof checked from a government engineering institude to be provided by the manufacturer for : i) sites with basic wind speed Greater then 45m/ sec as per IS 875 - part 3 ii) sites with structure height more then 20m for all wind speeds |
| 146 | Two track two panels sliding door with alumnium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on every panel along with multi point locking systed, adjustable nylon rollers with SS 304 body. |
| 147 | Using R3 Series with frame (55 mm & above ) X (40mm & above ) &sash ( 30 mm & above )x (75mm X above ). (height upto 2.5metre) |
| 148 | Three track three panel sliding door with two gazed & one wire mesh panels with aluminium channel for roller track, wool pile, zinc alloy (zamak) podwer coated handle on two panels a;ong with multi point locking system adjustable nylon rollers with SS304 Body. Using R3 Series with frame (98 mm & above ) X (40mm & above ) &both glazed and fly screen sash ( 30 mm & above )x (74mm X above ). (height upto 2.5metre) |
| 149 | Providing and fixing factory made upvc glazed/wire mesh window/ door comprising of lead free upvc multi -chambered frame, sash and mullion/ coupler (where ever required ) extruded profiles having minimum wall thickness of 1.70 mm series R1 and R2 profiles and 2.10 mm for series R3 and R4 profile confirming to EN 12608 in any shape colour and design duly reinforced with galvanized mild stell section made of required shape & size as per CPWD specification upc extruded glazing beads interlock and inline sash adaptor (where ever required ) of appropriate dimansion, EPDM gasket, hardwere, SS 304 grade fastners of minimum 8 mm dia with countersunk head comprising if matching polyamide PA6 IS 1367 Part 1 to 14 plastic packers plastic caps and nacessary stainless steel screws etc. profile of frame sash & mullion (if requred ) shall be mitred cut and fusion welded/ mechanically jointed duly sealed at all corners inculding drilling of holes for fixing hardware and driange of water etc. after fixing frame the gap between frame and adjaent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quility, all complete as per approved drawing confirminh to cpwd specification & direction of engineer in charge. section of steel reinfocement and cross sections of upvc profiles to be as per design approved by engineer in charge. wire mesh/ glazing of plain/ toughened /laminated/ double glass unit with / without high performance coating as per design requirements and confiming to IS 3548 & IS 16231 shall be paid separately. |
| 150 | Note:- structural design proof checked from a government engineering institude to be provided by the manufacturer for : i) sites with basic wind speed Greater then 45m/ sec as per IS 875 - part 3 ii) sites with structure height more then 20m for all wind speeds |
| 151 | Three track three panels sliding window with aluminium channel for rollar track, wool pile nylon rollers with SS 304 body. |
| 152 | Using R4 series with frame ( 115 mm & abovex (45 mm & above ) & sash (44 mm & aboove )x ( 55 mm & above ) with zinc alloy (zamak) powder coated handle on every panel along with multu point lockingh system (height above 1.8m). |
| 153 | Two track two panels sliding window with aluminium channel for roller track, wool pile, nylon rollers with SS304 body. Using R4 series with frame ( 115 mm & abovex (45 mm & above ) & sash (44 mm & aboove )x ( 55 mm & above ) with zinc alloy (zamak) powder coated handle on every panel along with multu point lockingh system (height above 1.8m). |
| 154 | Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer. Using M.S. angle 40x40x6 mm for diagonal braces |
| 155 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtainwall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 156 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. |
| 157 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels including: |
| 158 | Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: |
| 159 | (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. |
| 160 | (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. |
| 161 | (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. |
| 162 | (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporatingprinciples of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. |
| 163 | Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places |
| 164 | Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. |
| 165 | The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025. |
| 166 | (1). Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr. (2) Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml. (3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml. (4) Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm. (5) Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site. (6) Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml |
| 167 | Providing and fixing SGU 6mm Annealed glass in aluminium/uPVc windows, ventilators and partition etc. including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.The Properties of glass should be as : Solar heat gain Cofficiant (HSGC) =0.50 and Visual Light Transmission (VLT) =50% or more and shade to be approved by EIC/Architect. |
| 168 | Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge. |
| 169 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 170 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 171 | Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge |
| 172 | Providing and making cove in gypsum board. false ceiling with all accessories.as per drawing and instructions of Engineer in charge . |
| 173 | Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. |
| 174 | 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks) |
| 175 | MISCELLANEOUS WORK |
| 176 | Providing and fixing of Glass Fiber Reinforced Concrete (GFRC) Screen with borders 50mm thick and inner portion 35mm thick in approved size, pattern, Design, thickness and color. The Screen should be made From 53 grade white Portland cement/ 43 grade OPC or PPC gray cement manufactured by J.K. Cement or equivalent having minimum compressive Strength of 40N/mSQM, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by Sant Gobain,Owens corning or equivalent, super plasticizers and polymers manufactured by BASF, Sika, MYK Schomburg or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by Reckli or equivalent. The Fixing of Column should be Dry Fixing i.e. to be done with / MS Frames, Stainless Steel (SS-304) dash fasteners, Self-screw and pins. |
| 177 | Providing and fixing 20 Passenger Lift/ 1360Kgs / 1.25 Speed / 5 Floors / 5 Stops / Stainless Steel (1.5 Mm) Car Cabin,, as per specifications, drawings and as directed by Engineer-in-Charge |
| 178 | 1) DESIGN OF LIFTS - PASSENGER TYPE |
| 179 | 2) CAPACITY - 20 PASSENGER / 1360 KG |
| 180 | 3) SPEED - 1.25 m/s |
| 181 | 4) DRIVE - V3F |
| 182 | 5) WITH MACHINE ROOM |
| 183 | 6)TRAVEL - 21 Mtr. (Approximate) |
| 184 | 7) FLOORS - as per drawing |
| 185 | 8) NO. OF STOPS - 5 Stops |
| 186 | 9) REQUIRED WELL SIZE - as per Drawing |
| 187 | 10) POWER SUPPLY - 415 V - 3 Phase 50 HZ AC |
| 188 | 11) AUXILIARY - Single Phase 220 V AC |
| 189 | 12) CAR SIZE - Suitable for 20 Passengers |
| 190 | 13) CAR ENCLOSURE |
| 191 | a) CAR CEILING - SS HAIRLINE FINISH |
| 192 | b) CAR PANELS - SS HAIRLINE FINISH |
| 193 | c) ILLUMINATION - LED LIGHT |
| 194 | d) CAR FLOORING - 20 MM RECESS (FLOORING BY CUSTOMER) |
| 195 | 14) NO. OF ENTRANCE - ONE LOCATION FRONT |
| 196 | 15) CAR ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH |
| 197 | 16) DOOR SAFETY - FULL HEIGHT INFRARED LIGHT CURTAIN |
| 198 | 17) LANDING ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH |
| 199 | 18) CONTROL - SELECTIVE COLLECTIVE SIMPLEX |
| 200 | 19) ARD-TO BE PROVIDED |
| 201 | Providing and fixing 20 Passenger Lift/ 1360Kgs / 1.25 Speed / 4 Floors / 4 Stops / Stainless Steel (1.5 Mm) Car Cabin,, as per specifications, drawings and as directed by Engineer-in-Charge |
| 202 | 1) DESIGN OF LIFTS - PASSENGER TYPE |
| 203 | 2) CAPACITY - 20 PASSENGER / 1360 KG |
| 204 | 3) SPEED - 1.25 m/s |
| 205 | 4) DRIVE - V3F |
| 206 | 5) WITH MACHINE ROOM |
| 207 | 6)TRAVEL - 16 Mtr. (Approximate) |
| 208 | 7) FLOORS - as per drawing |
| 209 | 8) NO. OF STOPS - 4 Stops |
| 210 | 9) REQUIRED WELL SIZE - as per Drawing |
| 211 | 10) POWER SUPPLY - 415 V - 3 Phase 50 HZ AC |
| 212 | 11) AUXILIARY - Single Phase 220 V AC |
| 213 | 12) CAR SIZE - Suitable for 20 Passengers |
| 214 | 13) CAR ENCLOSURE |
| 215 | a) CAR CEILING - SS HAIRLINE FINISH |
| 216 | b) CAR PANELS - SS HAIRLINE FINISH |
| 217 | c) ILLUMINATION - LED LIGHT |
| 218 | d) CAR FLOORING - 20 MM RECESS (FLOORING BY CUSTOMER) |
| 219 | 14) NO. OF ENTRANCE - ONE LOCATION FRONT |
| 220 | 15) CAR ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH |
| 221 | 16) DOOR SAFETY - FULL HEIGHT INFRARED LIGHT CURTAIN |
| 222 | 17) LANDING ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH |
| 223 | 18) CONTROL - SELECTIVE COLLECTIVE SIMPLEX |
| 224 | 19) ARD-TO BE PROVIDED |
| 225 | Providing and fixing 16 Passenger Lift/ 1088Kgs / 1.25 Speed / 3 Floors / 3 Stops / Stainless Steel (1.5 Mm) Car Cabin,, as per specifications, drawings and as directed by Engineer-in-Charge |
| 226 | 1) DESIGN OF LIFTS - PASSENGER TYPE |
| 227 | 2) CAPACITY - 16 PASSENGER / 1088 KG |
| 228 | 3) SPEED - 1.25 m/s |
| 229 | 4) DRIVE - V3F |
| 230 | 5) WITH MACHINE ROOM |
| 231 | 6)TRAVEL - 12 Mtr. (Approximate) |
| 232 | 7) FLOORS - as per drawing |
| 233 | 8) NO. OF STOPS - 3 Stops |
| 234 | 9) REQUIRED WELL SIZE - as per Drawing |
| 235 | 10) POWER SUPPLY - 415 V - 3 Phase 50 HZ AC |
| 236 | 11) AUXILIARY - Single Phase 220 V AC |
| 237 | 12) CAR SIZE - Suitable for 20 Passengers |
| 238 | 13) CAR ENCLOSURE |
| 239 | a) CAR CEILING - SS HAIRLINE FINISH |
| 240 | b) CAR PANELS - SS HAIRLINE FINISH |
| 241 | c) ILLUMINATION - LED LIGHT |
| 242 | d) CAR FLOORING - 20 MM RECESS (FLOORING BY CUSTOMER) |
| 243 | 14) NO. OF ENTRANCE - ONE LOCATION FRONT |
| 244 | 15) CAR ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH |
| 245 | 16) DOOR SAFETY - FULL HEIGHT INFRARED LIGHT CURTAIN |
| 246 | 17) LANDING ENTRANCE - AUTOMATIC COPD DOORS IN SS HAIRLINE FINISH |
| 247 | 18) CONTROL - SELECTIVE COLLECTIVE SIMPLEX |
| 248 | 19) ARD-TO BE PROVIDED |
| 249 | CARRAIGE OF MATERIALS |
| 250 | SAND (UPTO 10KM LEAD) |
| 251 | CHIPS (UPTO 22KM LEAD) |
| 252 | BRICKS (UPTO 8KM LEAD) |
| 253 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. |
| 254 | Plant mix method (Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401) (ii) Rate per cum for grading-II Material |
| 255 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweepingextra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-35 grade with approved color design and pattern. |
| 256 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all omplete as per the direction of Engineer-in-charge. |
| 257 | Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge |
| 258 | Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme onthe boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge. |
| 259 | PLUMBING WORK |
| 260 | Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l . |
| 261 | Providing and fixing 15 mm dia male ended C.I .Body brass spindle valve and seat bib cock of approved quality (wt not less than 400 gms ) with extra socket all complete as per specification and direction of E/l . |
| 262 | Providing and fixing 15 mm dia male ended C.I push cock (wt not less than 400 gms) of approved quality with extra socket all complete as per specification and direction of E/l . |
| 263 | Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l . |
| 264 | A) BRASS STOP COCK |
| 265 | (a) 15 mm dia |
| 266 | (b) 20 mm dia |
| 267 | Providing and fixing 15 mm dia and 45 cm. long P. V .C connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of E/l . |
| 268 | Providing and fixing 15mm size C.P brass pillar cock (Weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per spcification and direction of E/l. (b) C.I. body brass spindle |
| 269 | Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l |
| 270 | (a) 15 mm dia wt not less than 300 gms |
| 271 | (b) 20mm dia wt not less than 400 gms |
| 272 | (c) 25 mm dia wt not less than 500 gms |
| 273 | (d) 32 mm dia wt not less than 700 gms |
| 274 | (e) 40 mm dia wt not less than 1kg |
| 275 | (f) 50 mm dia wt not less than 1.5 kg |
| 276 | Cutting drain width wise above G.L for laying G.I pipes and restoring with brick in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/l |
| 277 | Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l. |
| 278 | Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l. (a) Mirrors of 6 mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror |
| 279 | (1)600x450 mm size |
| 280 | (2) C.P brass liquid shop container |
| 281 | Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with \\"p\\" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. |
| 282 | (B) 510 mm long |
| 283 | (a)12.5 lit. low level P.V.C. cistern |
| 284 | Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I. Kitchen sink 600mm ×450mm×250mm. |
| 285 | Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l. |
| 286 | (i) 125 mm dia |
| 287 | (ii) 250 mm dia |
| 288 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm |
| 289 | Providing and fixing toilet paper holder : C.P. brass |
| 290 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms |
| 291 | Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms |
| 292 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 293 | Flexible pipe |
| 294 | 32 mm dia |
| 295 | 40 mm dia |
| 296 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 297 | Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. 110mm dia |
| 298 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. |
| 299 | Coupler 110 mm dia |
| 300 | Single Tee with door 110x110x110 mm |
| 301 | Bend 87.5 deg 110 mm |
| 302 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe |
| 303 | Providing and fixing unplasticised- PVC pipe clip of approved desing to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwes with M.S. Screw of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 Cement : 4 Coarse sand ) and making good the wall etc. complete. 110mm dia |
| 304 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of appx.size 610x390x370mm having pre & post flushing with water (250ml & 500ml consumption) having water inlet from back side,including fixing to wall with suitable brackets all as per manufacturers specification & direction of Engineer-in charge. |
| 305 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): |
| 306 | 65 mm nominal bore |
| 307 | 80 mm nominal bore |
| 308 | Providing and fixing C.P. bass angle valve of approved quality conforming to I.S:8931. 15 mm nominal bore |
| 309 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams. |
| 310 | Providing and fixing wash basin with CI brackets,15mm brass pillar taps,32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required. White vitreous china wash basin size 630 mm x 450 mm with a single 15mm CP brass pillar tap. |
| 311 | Providing and fixing G.I. pipes conforming to I:S including all fittings, testing, cutting holes or chases and making good where required. (For waste connections) 32mm dia |
| 312 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 32mm dia |
| 313 | Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia |
| 314 | Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating |
| 315 | Providing fixing, testing and commissioning in position SWR PVC PIPE TYPE-B pipe comforming to IS:13592 including all fittings such as bends, junctions, inspection doors, offests, cowl, access pieces/clean out plugs, clamps /supports/ hangers etc. jointing with PVC Adhesive joints including cutting holes in walls, core cutting in slabs and making good the same. all complete as per specification and direction of E/l. |
| 316 | (a) 250 mm dia |
| 317 | (a) 150 mm dia |
| 318 | (c) 100 mm dia |
| 319 | (d) 75 mm dia |
| 320 | (e) 50 mm dia |
| 321 | (f) 25 mm dia |
| 322 | Providing & fixing in position uPVC P\\"or S\\" trap of self cleaning design of following sizes for the embedded areas. Making proper connection with drip-seal joints, cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors where required. |
| 323 | 3 x 50 mm inlet and 100 mm outlet (Multi Floor Trap) |
| 324 | 50 mm outlet (Floor Drain) |
| 325 | Providing & fixing in position storage type hot water electrical geyser (vertical or horizontal-1.5 kw) including making connection in all respects.-Venus/Racold make. |
| 326 | 15 litres capacity (Make: AO Smith or equivalent) |
| 327 | 25 litres capacity (Make: AO Smith) |
| 328 | Supply installation testing and commissioning R.O.water purifier comprising 5 micron filter and UV steriliser on cold water supply to work on single phase 230 volts 50 HZ AC power supply with capacity 100 lph.-K |
| 329 | Fixing of Wall Mounted C.P. Brass Single lever Sink Mixer with swinging spout of required size including cuttinig and making good the wall wherever required. |
| 330 | Providing & fixing C.P. hand spray with lever control (health faucet) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge. |
| 331 | Providing & fixing chinaware urinal partition of 160X 400X 825 mm with fixed with expandable anchor fasteners with C.P. brass bolts and washers, embedded in wall with anchor and set in cement concrete complete including cutting and making good the walls wherever required |
| 332 | Providing & fixing soild state no touch operating fully highgenic SS hand drier of best quality, to be operated with 230 volts, single phase, with fully hygienic condition, with all accessories including cutting and making good the walls, wherever required. |
| 333 | Providing and Fixing in position Hindware make or equivalent CP Grab Bar with wall flanges 600 mm to wooden cleats with C.P. brass screws complete in all respects. |
| 334 | Providing and fixing C.P. brass twin coat hooks fixed on toilet door with including CP brass screws, washers rawl plugh etc. complete in all respact. |
| 335 | Supplying and fixing 100 mm dia SWR PVC End Cap (Clean Outlet Plug) fittings of approved make. all complete as per specification and direction of E/l. |
| 336 | Supplying and fixing 250 mm dia SWR PVC End Cap (Clean Outlet Plug) fittings of approved make all complete as per specification and direction of E/l. |
| 337 | Providing & fixing horizontal centrifugal pumps for domestic water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly. Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank. |
| 338 | Domestic Water Supply at terrace l - Set of Two Pumps (1 Working+ 1 Standby), Capacity 1.5 LPS, Head - 40 M., HP -2.5 HP Approxi. |
| 339 | Flushing Water Supply at STP Pump Rm - Set of Two Pumps (1 Working+ 1 Standby), Capacity -1.0 LPS, Head -40 M., HP - 1.5 HP Approxi. |
| 340 | Providing & fixing horizontal centrifugal pumps for domestic water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly.Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank. |
| 341 | Domestic water Pumps inlet |
| 342 | Location - Transfer pump to Terrace from pump room |
| 343 | Capacity 3.0 LPS each |
| 344 | Head 55 Mts |
| 345 | RPM 2900 |
| 346 | HP(appx) - 3.5 |
| 347 | Pumps & associated works as described above |
| 348 | Providing & fixing horizontal centrifugal pumps for flushing water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly.Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank. |
| 349 | Flushing water lifting Pumps |
| 350 | Location - Inside pump room |
| 351 | Capacity 2.0 LPS each |
| 352 | Head 40 Mts |
| 353 | RPM 2900 |
| 354 | HP(appx) - 2.0 |
| 355 | Pumps & associated works as described above |
| 356 | Supplying, assembly, erection, testing and commissioning of magnetic level sensors and controllers, CPVC probe tube, PP actuating float and all other equipment required for the performance of the system to the satisfaction of the engineer in charge complete including providing and fixing wiring from control junction box near the UG tank to probes of required length, interconnection wiring between level controller and the concerned contactor in the starter panel as required. The level controller will perform the following functions. |
| 357 | To switch on the pumps (including tube well pumps 1 nos., raw water pumps (Domestic Water Treatment, Domestic & Flushing and etc.) when the level of water in the supply waterline is low and to cut off the pump when the level in the receiving water line is high and switch off the pumps when the level of water in the supply water line is low. |
| 358 | To indicate 2 levels of water in all tanks through a control panel with LEDs |
| 359 | To start the pumps in a cyclic order. |
| 360 | The system shall be complete to ensure automatic quotation of pump in accordance to water level in respective tanks. |
| 361 | The Contractor will include all the under ground and over head tanks and all the pumps as required for level control in this item |
| 362 | Providing & fixing horizontal centrifugal pumps for domestic water lifting with CI casing bronze impeller suitable for operation on 400 / 440 V pH 50 cycle A/C power supply.Cost shall include electrical control panel (star/dol starter) with all controls to make the pumps to operate automaticaly.Sequencing shall be provided for the pumps.Pumps shall start /stop automatically depanding upon water level in overhead tank. |
| 363 | Domestic water Pumps inlet |
| 364 | Location - Transfer pump to Terrace from pump room |
| 365 | Capacity 1.0 LPS each |
| 366 | Head 30 Mts |
| 367 | RPM 2900 |
| 368 | HP(appx) - 1.5 |
| 369 | Pumps & associated works as described above |
| 370 | Filter Feed Pump FROM RAW WATER TO DOMESTIC WATER TRANSFER PUMP ) |
| 371 | Location - Pump room |
| 372 | Capacity 1.5 LPS each |
| 373 | Head 25 Mts |
| 374 | RPM 2900 |
| 375 | HP(appx) - 1.5 |
| 376 | Pumps & associated works as described above |
| 377 | Sump PumpProviding and fixing compact monoblock dry motor submersible pumps of suitable rating, with non-clog free flow open impeller, suitable for operation on 415 volts +10% , 3 Phase, 50Hz, A.C supply, speed 2900 RPM including oil chamber, guide wire for lifting & lowering of pump, M.S. galvanized lifting chain, duck foot bend complete. The pump sets shall be supplied with required accessories & as per specification with the following : |
| 378 | Complete inlet, outlet and header piping of suitable dia (velocity shall not exceed 1.5m/s) -- 1 Lot |
| 379 | Butterfly valve and Dual Plate NRV of appropriate dia and rating - 1 Lot |
| 380 | Necessary cables from pump sets to pump starter panel - 1 Lot |
| 381 | Electrical control panel having all necessary accessories & safety devices of standard specifications and suitable for receiving incomer cable to connect complete. (Panels with sump pumps near each sump as per site conditions). -- 1 No. |
| 382 | Discharge :5 m3/Hr |
| 383 | Head : 25 m |
| 384 | Solid Handling : 50 mm |
| 385 | Note : |
| 386 | Pumps shall be operated on cyclic timing |
| 387 | The entire system along with pumps & control panel must be sourced from single manufacturer only for unit responsibility. |
| 388 | One set consist of 2 nos.of pumps - 1 working & 1 stand by (Complete set as above with 2 nos. pumps including cost for valves, piping, Control Panel and Cabling, Level Controllers, pressure gauges etc as required and as specified) |
| 389 | MULTIGRADE SAND FILTER (For Domestic Water Supply) |
| 390 | Supply, assembly, erection, testing & commissioning of vertical M.S. Dual Media filter fabricated from 6mm thick M.S plate shell and 8mm thick M.S. plate dished ends with 3mm non-toxic, non-leaching rubber lining (rubber lining to be tested for pin-holes by spark tester) inside complete with initial charge of filter media activated carbon, face piping (GI, C Class), diaphragm/ball/non-return valves, accessories, painting, testing and commissioning of any under drainage system as required, complete. (Tested to 10 kg/sq cm) |
| 391 | Capacity : 1.5 lps |
| 392 | Filtration rate : 18-20 M³/M²/hr |
| 393 | Max. operating pressure : 3.5 Kg/Sq.cm |
| 394 | Test pressure : 5.5 Kg/Sq.cm |
| 395 | ACTIVATED CARBON FILTER (For Domestic Water Supply) |
| 396 | Supply, assembly, erection, testing & commissioning of vertical M.S. Activated Carbon filter fabricated from 6mm thick M.S plate shell and 8mm thick M.S. plate dished ends with 3mm non-toxic, non-leaching rubber lining (rubber lining to be tested for pin-holes by spark tester) inside complete with initial charge of filter media activated carbon, face piping (GI, C Class), diaphragm/ball/non-return valves, accessories, painting, testing and commissioning of any under drainage system as required, complete. (Tested to 10 kg/sq cm) |
| 397 | Capacity : 1.5 lps |
| 398 | Filtration rate : 15-17 M³/M²/hr |
| 399 | Max. operating pressure : 3.5 kg/Sq.cm |
| 400 | Test pressure : 5.5 Kg/Sq.cm |
| 401 | DOMESTIC WATER SUPPLY PUMP PANEL (AT PLANT ROOM) Ics=35 KA |
| 402 | Supplying, Installation, Testing and Commissioning of dust and vermin proof wall / floor mounting type factory built sheet steel enclosed cubical panel, fabricated out of 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with Aluminium bus bars, inter-connection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per specifications and as required (all the starters should have BMS compatible with required NO/NC contacts etc). |
| 403 | INCOMING |
| 404 | 125 A, TPN, 35 kA rating MCB - 01 No. |
| 405 | Digital flush type class - I accuracy multifunction meter 0-250A, showing V, A, KWH, KVA, PF etc. with 3 Nos. current transformers of 250/5 Amp ratio, 15 VA Class 1.0 metering. |
| 406 | Coloured LED (Red, Yellow, Blue) phase indicating lamps |
| 407 | Bus Bar |
| 408 | 150 Amp. 35 kA, TPN Cu. Bus Bar |
| 409 | OUTGOING |
| 410 | 32A, TP,10 kA 'C' series MCCB, coloured LED type ON indication - (1w+1s) Nos & 1 Spare |
| 411 | 32A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare |
| 412 | 25A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare |
| 413 | 16A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare |
| 414 | 16A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 2 Nos & 2 Spare |
| 415 | 16A, TP, 10 kA 'C' series MCCB, coloured LED type ON indication -(1w+1s) 1 Nos & 1 Spare |
| 416 | Fully automatic DOL starter suitable for 7.0 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos (Borewell Pump) |
| 417 | Fully automatic DOL starter suitable for 3.5 HP motor including 40 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Domestic Pump at terrace) |
| 418 | Fully automatic DOL starter suitable for 3.0 HP motor including 40 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Flushing Pump at terrace) |
| 419 | Fully automatic DOL starter suitable for 3.5 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Domestic water transfer pump) |
| 420 | Fully automatic DOL starter suitable for 1.0 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 2 Nos.(Sump Pump) |
| 421 | Fully automatic DOL starter suitable for 1.5 HP motor including 25 A TP MCCB 'C' series, CT's, Ammeter, Push Button, Indicators, Auto/Manual/OFF switch, SPPR, Relay, metering & indication etc. - (1w+1s) 1 Nos.(Filter feed Pump) |
| 422 | Domestic water supply Panel. (At Plant Room) |
| 423 | Constructing water tight brick masonry grease trap with first class bricks in cement mortar 1:6 (1 cement :6 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size, foundation concrete 150 mm thick 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement & M.S. foot rests including fixing in 20 x 20 x 10 cm cement concrete blocks 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size), two brick masonry baffle walls each of 500 mm depth deep each of 115 mm thickness, 2 Nos C.I. double seal medium duty covers each of 450 x 450 mm size including excavation, backfilling & disposal of surplus earth with a lead upto 50m complete as per standard design. (Note: Cost shall include dewatering & water proofing of Grease trap as directed at site). Grease Trap (Size 1200 x 900 x 1000 mm overall depth). |
| 424 | Providing and fixing M.S. puddle flanges fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be painted with black Japan paint . |
| 425 | 25 mm dia |
| 426 | 40 mm dia |
| 427 | 50 mm dia |
| 428 | 65 mm dia |
| 429 | 80 mm dia |
| 430 | 100 mm dia |
| 431 | 150 mm dia |
| 432 | 250 mm dia |
| 433 | Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of engineer in charge. |
| 434 | 150mm dia |
| 435 | 200mm dia |
| 436 | Supplying and fixing 150 mm dia PVC End Cap (Clean Outlet Plug) fittings of approved make all complete as per specification and direction of E/l. |
| 437 | Providing and fixing forged brass auto air vent valve PN10 (10.00 Kg/cm2) rating including all fitting with ball valve & accessories. 15 mm dia |
| 438 | Providing, fixing, testing & commissioning of wafer type cast iron butterfly valves conforming to BS 5155 & IS 13095 tested to 15 Kg/Sq.cm pressure for maximum working pressure of 10 bar (PN 10) including all fitting and accessories (Drain, water meter for OH Tank/Riser). |
| 439 | 50 mm dia |
| 440 | 65 mm dia |
| 441 | 80 mm dia |
| 442 | 100 mm dia |
| 443 | Providing and fixing G.I. Vent Pipe class 'B' (medium duty) for R.C.C water storage tanks comprising of 600 mm long vertical pipe, return bend with mosquito grating & cast brass perforated coupling including all associated civil work. 100 mm dia |
| 444 | Providing and fixing of mosquito overflow grating /Jali of the following diameters including all fitings & accessories :- 100 mm dia |
| 445 | Excavating trenches of required width for pipes including excavation for sockets also including for cement concrete craddles, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer with minimum 95% by ramming, watering etc. and disposing off surplus excavated soil as directed, within a lead of 50 m. UPTO 1.5M Pipes, cables etc, not exceeding 80 mm dia. |
| 446 | Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia |
| 447 | Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre). |
| 448 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. |
| 449 | Internal Work - Exposed on Wall |
| 450 | 15 mm nominal outer dia pipes. |
| 451 | 20 mm nominal outer dia pipes. |
| 452 | 25 mm nominal outer dia pipes. |
| 453 | 32 mm nominal outer dia pipes. |
| 454 | Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the the same including testing of joints complete as per direction of engineer in charge. |
| 455 | Concealed work including cutting chases and making good the walls etc. |
| 456 | 15 mm nominal outer dia pipes. |
| 457 | 20 mm nominal outer dia pipes. |
| 458 | 25 mm nominal outer dia pipes. |
| 459 | 32 mm nominal outer dia pipes. |
| 460 | Fixing water meter and stop cock in G.I pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). |
| 461 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. [Location : From Bore Well/Tanker water supply line/Municipal line to Underground Water Storage Tank]. 80 mm dia |
| 462 | Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),i/c necessary excavation foundation concrete 1:5:10 (1 Cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 Cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design: a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 463 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 464 | Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 grams with threaded end for hose connection. |
| 465 | Providing and fixing gun metal non- return valve of approved quality (screwed end). |
| 466 | 50 mm dia nominal bore-vertical |
| 467 | 65 mm dia nominal bore-vertical |
| 468 | 80 mm dia nominal bore-vertical |
| 469 | Supplying and fixing C.I. cover without frame for manholes: 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg. |
| 470 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore |
| 471 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 472 | 25 mm nominal bore |
| 473 | 20 mm nominal bore |
| 474 | 32 mm nominal bore. |
| 475 | 40 mm nominal bore |
| 476 | 50 mm nominal bore |
| 477 | 65 mm nominal bore |
| 478 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete |
| 479 | 15 mm nominal bore |
| 480 | 20 mm nominal bore |
| 481 | 25 mm nominal bore |
| 482 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : |
| 483 | 20 mm nominal bore |
| 484 | 25 mm nominal bore |
| 485 | 32 mm nominal bore. |
| 486 | 40 mm nominal bore |
| 487 | 50 mm nominal bore |
| 488 | 65 mm nominal bore |
| 489 | Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand) including testing of joints etc. complete. |
| 490 | 150 mm. dia. RCC Pipes |
| 491 | 250 mm. dia. RCC Pipes |
| 492 | 300 mm. dia. RCC Pipes |
| 493 | Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes : |
| 494 | 4.0Cx6 Sqm |
| 495 | 4.0Cx10 Sqm |
| 496 | 4C x 16 Sq. mm |
| 497 | Providing and fixing square mouth SW gully trap class SP-1 complete CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.7 kg. as per standard design. 100x100mm size P type With common burnt clay F.P.S (non modular) bricks of class designation 7.5. |
| 498 | Construction brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. |
| 499 | Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 500 | Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 501 | Extra for depth for manholes Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 502 | Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 503 | Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : |
| 504 | 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 505 | Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 506 | Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : |
| 507 | 1.68 m deep with SFRC Cover and frame (heavy duty HD 20 grade designation) 560 mm internal diameter conform ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 ce ment : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 508 | Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 509 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 510 | Constructing brick masonry road gully chamber 50 X 45 X 60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500 X 450 mm precast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S (non modular) bricks of class designation 7.5. |
| 511 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS : 12818, including hire & labour charges, fittings & accessories etc, all complete, for all depths, as per direction of engineer-in-charge. 100mm nominal size dia |
| 512 | Supplying & filling, sepreading & leveling stone boulders of size range 5cm to 20cm, in the recharge pit, in the required thickness, for all leads & lifts, all complete, for all depths, as per direction of engineer-in-charge. |
| 513 | Supplying & filling, sepreading & leveling gravels of size range 5mm to 10mm, in the recharge pit, over the existing layer of boulders, in the required thickness, for all leads & lifts, all complete, as per direction of engineer-in-charge. |
| 514 | Supplying & filling, sepreading & leveling coarse sand of size range 1.5mm to 20mm, in the recharge pit, in the required thickness over gravel layer, for all leads & lifts, all complete, as per direction of engineer-in-charge. |
| 515 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Rectangular shape 600x450 mm internal dimensions |
| 516 | Cost of Drilind 200mmx165mmx125m dia Deep Bore well in all kind of soil and rock in rural area for instalation of pump set with hydrolic DTH rig machine all complete including all materials ,tools ,drilling rig air compressureand equipmentsas well as fuel ,lubricantsand of rig machine and other vehical up to site . |
| 517 | (a) From 0.0m to 50.0 m Below G.L |
| 518 | (b) From 51.0 to 125.0 m Below G.L |
| 519 | (C) From 126M to 150.0 m Below G.L |
| 520 | DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area |
| 521 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing(CM) pipe OF Required dia, conforming to IS:12818, including required hire and labour charge , fitting & accessories etc . All complete, for depths as per direction of engineer in charde-200 mm nominal size dia |
| 522 | Development of tube well in accordance with IS : 2800 (partI) IS :11189 to establish maximum rate of usable water yield without sand content ( beyond permissible limit) with required capacity air compressor ,running the compressor for required time till well is fully developed ,measuring yield of well by V notch method or any other approved methode ,mesuring static level & drwan etc by step drawn down method collecting water samples & getting tested in approved laboratory i/c disinfection of tube well all complete hire & labour charges of air compresssor ,tools & accessories stc all as per requirement and direction of engineer in charge. |
| 523 | Supplying Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump ste shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run shall be provided with each pump.Submersible pump set 50mm dia (with polypropylene/ Noryl Impeller) up to 20 stages 2 HP |
| 524 | Supply fitting and fixing of standard make starter panel board with arrengement of all neccessery protection including all tax , all complite job as direction of E/I |
| 525 | Supply fitting fixing 3 core 4 sqmm flate copper submersible cable including all tax royalty Etc all complite job as per direction E/I |
| 526 | Supply fitting and fixing lowering 40mm dia G.L column pipe do-do- all complite job as per direction of E/I |
| 527 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia |
| 528 | Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm dia |
| 529 | FIRE FIGHTING |
| 530 | WET RISER SYSTEM - PUMPING EQUIPMENTS |
| 531 | Supply, Installation, Testing and Commissioning of Electric Driven Main Fire Pump suitable for auto operation & consisting of following: complete in all respect as required.The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% of the rated head. The shut off head shall not exceed 120% of the rated head. (Sprinkler & Hydrant Pump) |
| 532 | a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520. |
| 533 | b) Suitable HP squirrel cage induction motor, TEFC synchronous speed 2900 RPM (with permissible slip), suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, confirming to IS-325. |
| 534 | c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications. |
| 535 | Supply, Installation, Testing and Commissioning of Diesel Engine Driven Main Fire Pump suitable for auto operation and consisting of following: complete in all respect as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head. The shut off head shall not exceed 120% of the rated head. |
| 536 | a) Horizontal end suction type, centrifugal, single stage, pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm. at highest and farthest outlet at specified flow of 2280 lpm at 88 Mtr. head confirming to IS 1520. |
| 537 | b) Suitable HP 1500 RPM, 4 stroke, cold starting type Diesel Engine with Heat Exchanger confirming to relevant BIS & IS Standards, complete with all required accessories / system, fuel oil filter, lubricant oil pump with filter, 2 Nos. starting batteries of 180 AH capacity each with suitable angle iron stand, engine starting panel having all the controls meters, gauges, tachometer, hour meters, starting switch with keys for manual starting, auto starting mechanism, Including inbuilt electrical panel which will be activate by pressure switch, Including cables etc., 24 Volts electric starting equipment, Diesel Tank for 8 hrs continuous running of diesel engine, having minimum capacity of 200 Ltrs. (tank made out of 3mm thick M.S. Sheet with filling Cap, drain Cock, diesel indicator duly mounted on M.S. angle) exhaust pipe extended upto 1 mtr. outside pump house, duly insulated with 50 mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, exhaust residential silencer, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. |
| 538 | c) M.S. fabricated Common base frame, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation (minimum 6\\" above from ground floor) duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications. |
| 539 | Supplying, Installation, Testing and Commissioning of Electric Driven Pressurization Pump (Jockey Pump) suitable for auto operation and consisting of following: complete in all respects as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head. |
| 540 | a) Horizontal type, centrifugal end suction type pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal, gland packing and flow of 180 Ipm at 88Mtr. head confirming to IS:1520. |
| 541 | b) Suitable HP (Minimum 4.0-5.0 HP) squirrel cage induction motor TEFC type 2900 RPM suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP-55 class of protection for enclosure, horizontal foot mounted type with Class - 'F' insulation, confirming to IS:325. |
| 542 | c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications. |
| 543 | Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 6 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes 1.2 Meter high and 250 mm dia |
| 544 | Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 8 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes 2 Meter high and 450 mm dia suitable to operate Jockey Pump, Main Fire Pump , Sprinkler pump & Diesel Engine Driven Fire Pump |
| 545 | HYDRANTS SYSTEM |
| 546 | Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS : 5290 (Type A), with 80 mm dia flanged inlet, with ABS cap and chain complete with all accessories etc. as required. |
| 547 | Supply, Installation, Testing and Commissioning of 63 mm dia. 15 Mtr. Long RRL hose pipe with 63 mm dia. male and female stainless steel couplings duly binded with GI wire rivets etc. ISI marked, IS 636 (type-A) as required. |
| 548 | Supplying and fixing 63 mm dia. Stainless Steel branch pipe with 20mm dia nozzle conforming to IS:903. suitable for instantaneous connections to hose pipe coupling etc. as required. |
| 549 | Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction, spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required. 30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585 20 mm dia. ball valve & nozzle. Drum and brackets for fixing the equipments on wall. Connection from riser with 25 mm dia (Gun metal) stop valve & M.S. Pipe. |
| 550 | Supplying, installation, testing and commissioning of weather proof M.S cabinet size 1200 mm x 2100 mm x 600mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following. |
| 551 | Gunmetal single headed Hydrant valve - 1 No. |
| 552 | Fire Hoses 63mm, 15 M long with accessories - 2 Nos. |
| 553 | Short branch - 1 No. |
| 554 | First Aid hose Reel - 1 No. |
| 555 | Fire Extinguisher - 2 Nos. |
| 556 | Fireman's Axe - 1 No. |
| 557 | Pressure Gauge - 1 No. |
| 558 | The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade. |
| 559 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male & female instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : |
| 560 | 2 way - 100 mm dia M.S. Pipe |
| 561 | 4 way - 150 mm dia M.S. Pipe |
| 562 | PIPING, VALVES AND ACCESSORIES |
| 563 | Supplying, laying, fixing, testing and commissioning of following sizes (NB) of class 'C' M.S. pipes confirming to IS 1239 and 3589 including cutting, threading, welding etc. and providing all fittings e.g. elbows, reducers, clamps, hangers, flanges, gaskets, nuts, bolts and washers etc. including painting of pipes and fittings with red paint over a coat of ready mixed primer, both of approved quality and shade including cutting holes and chases in brick or RCC walls/slabs and making good the same etc. complete in all respect as required.(The Welding shall not be done for piping less than 50 mm dia.) |
| 564 | 150 mm dia |
| 565 | 100 mm dia |
| 566 | 80 mm dia |
| 567 | 65 mm dia |
| 568 | 50 mm dia |
| 569 | 40 mm dia |
| 570 | 32 mm dia |
| 571 | 25 mm dia |
| 572 | Supplying, Installation, Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with EPDM rubber lining seat and CF-8 stainless steel disc duly ISI marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required. |
| 573 | 150 mm dia |
| 574 | 80 mm dia |
| 575 | 65 mm dia |
| 576 | Supplying and fixing Orifice Plate made of 6 mm thick, stainless steel with orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 Kg / cm2 complete as per specifications as required. |
| 577 | Providing, Installation, Testing and Commissioning of double flanged cast iron Dual Plat Check Valve (Non-Return Valve), PN 1.6 of following sizes confirming to IS : 5312 complete with EPDM rubber lining seat and stainless steel disc, rubber gasket, Gl bolts, nuts, washers etc. as required. |
| 578 | 150 mm dia |
| 579 | 65 mm dia |
| 580 | Supplying, Installation, Testing and Commissioning of CI body flanged (both ends) type serviceable suction / Y strainer with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. complete as required. |
| 581 | 150 mm dia |
| 582 | 65 mm dia |
| 583 | Providing & fixing double flanged Metallic expansion with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications. |
| 584 | 150 mm dia |
| 585 | 65 mm dia |
| 586 | Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centrigade with required accessories : |
| 587 | Pendent Sprinkler |
| 588 | Upright Sprinkler |
| 589 | Sidewall Sprinkler |
| 590 | Providing & fixing of pressure gauge in M.S. pipe line including connection etc. as required. |
| 591 | Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150mm dia |
| 592 | Providing, fixing, testing & commissioning of installation control valve of cast irom body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulic driven mechanical gong bell to sound continous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency release, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice pate, gasket etc of following sizes as required 150mm dia |
| 593 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes coplete as required. |
| 594 | 700mm |
| 595 | 1000mm |
| 596 | 1200mm |
| 597 | Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926. |
| 598 | Powder Fire Extinguisher (Stored Pressure type) Capacity 09 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609, ISI marked ABC powder complete with squeeze grip release valve, discharge pipe locking arrangement, pressure gauge, operation manual and bracket. Operating Temperature: - 10ºC to + 55ºC. Brand LIFEGUARD |
| 599 | Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006 4.5kg capacity cylinder |
| 600 | Providing and fixing in position approved make fire bucket of 24 gauge, galvanized steel, standard 9 liters capacity and of round bottom shape, panted white inside and red outside and black on bottom dome with letters ‘FIRE’ in black and gold with all mounting bracket and screws. |
| 601 | Providing and fixing of fire Bucket Stand including sheet metal (16 gauge) shade for 2 buckets. Platform and associated civil works complete. |
| 602 | MOTOR CONTROL PANELS |
| 603 | Supplying, assembling, erecting, connecting, testing and commissioning of Outdoor type fire fighting double door lockable type with epoxy paint. This panel shall be mounting on MS/brick pedestal support upto 400 mm high from ground level,cubical, dust, vermin proof and outdoor type (IP65) fabricated as per specification laid in document with following incomming and outgoing feeders including making connections/inter-connections testing and earthing etc. required with necessary interlocking with existing panel as shown in drawing as per specification and mounted with the followings. |
| 604 | Incoming |
| 605 | 1 No. - 630A 4P ATS |
| 606 | 1 No. - 630A TPN MCCB of fault breaking capacity 50 kA (Ics = Icu upto 500V), fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with following accessories for each MCCB. |
| 607 | Independent electrical/manual spring closing mechanism - 1 No. |
| 608 | Microprocessor releases based relay(EMI & EMC certified) for over current, earth fault & short circuit protections with trip indications for each - 1 set. |
| 609 | Dual core calibrated digital Multifunctional meter of class 1.0 to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral) and 3 Nos. dual core CT of A Class 1.0 accuracy and 15 VA burden. |
| 610 | Following indicating lamps and push buttons for each MCCB with back up 2A SP MCB . |
| 611 | 3 No. Phase indicating Lamps . |
| 612 | Indicating Lamps for the following; |
| 613 | Bus Bar |
| 614 | 800 Amp. 50 kA, TPN Al. Bus Bar |
| 615 | Outgoings: |
| 616 | Following rated 420V,50KA MCCB's with overcurrent and short circuit releases Microprocessor based with ON,Trip indications, front operating handle & door interlock along with 2A SP MCB backup protection and control terminals & wiring as required. etc. complete in all respects as mentioned in specifications and as required For each outgoing: |
| 617 | 125 Amp. TP MCCB -4 Nos.(4 spare) |
| 618 | 16 Amp. TP MCCB -2 Nos.(2 spare) |
| 619 | Fully automatic Star Delta starter suitable for operating 2280 lpm (50 HP) motors/fan capacity, complete with contactors,Timer, overload protection relay, current sensing type single phase preventer, ON indications, push buttons, auto / manual / off selector switch,other accessories. complete as required. - 4 set. |
| 620 | Fully automatic DOL starter suitable for operating 180 lpm (4.0 HP) HP motors/fan capacity, complete with contactors,Timer, overload protection relay, current sensing type single phase preventer, ON indications, push buttons, auto / manual / off selector switch,other accessories. complete as required. - 2 set. |
| 621 | The Panel shall have necessary arrangement to start the pumps at automatic mode in following sequence. a) The Jockey Pump is start to maintain the drop in pressure in pipe line and also in case of opening of any hydrant to maintain the required pressure. b) The main fire pump will start in case of jockey doesnot able to maintain the required pressure due to opening of any fire hydrant. c) To start the diesel engine operated fire pump in case of failure of power supply or in case of minimum fire pump is not able to required pressure. |
| 622 | (d) Diesel Engine Control |
| 623 | Control for Diesel Engine comprising:- |
| 624 | (i) Auto/Manual selector switch & 3 attempt starting device, timers and relays as required, push buttons, start/stop in manual mode. |
| 625 | (ii) Indication lamp for High Water Temp. and Engine on indication and suitable tripping devices, overload, earth fault protection relays etc as required. |
| 626 | (iii)Battery charger suitable for 12 V/24 V DC with boost and tickle selector switch 0-15V/0-30V DC meter 0-20A DC Ammeter. |
| 627 | (iv) All standard relays and accessories for automatic operation of diesel engine. |
| 628 | (e) System Controller |
| 629 | Designing, Supply, Installation, Testing and commissioning of system controller to control operation of Main Fire Pump, Pressurization Pump in sequence as per specification consisting of relays, timers, sensor, annunciation window for fault indication, complete as per specification. |
| 630 | Fire panel as above |
| 631 | ELECTRICAL WORK |
| 632 | SUB-STATION |
| 633 | METERING INDOOR UNIT |
| 634 | Providing & fixing 11KV CT & PT in above metering indoor unit and getting them calibrated from State Electricity Boards before fixing. |
| 635 | 11KV SINGLE VCB PANEL BOARD (NEAR METER) |
| 636 | Design, manufacturer, supply of panel board fabricated out of minimum 2 mm thick sheet steel as per specifications. The panel shall be complete with cable termination arrangement suitable for incoming and outgoing each 1 run x 3C x 240 Sqmm XLPE 11 KV cable and copper bus bar arrangement. The panel shall comprise of the following: |
| 637 | Single Panel Board |
| 638 | Incomer:- |
| 639 | 1No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC |
| 640 | Each incomer comprising with following accessaries. |
| 641 | 1 No. Mechanical ON/OFF Indicator |
| 642 | 1 No. Aux Switch 6NO + 6NC |
| 643 | Panel, Busbar, CT, PT |
| 644 | 1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable |
| 645 | 3 Nos. Resin Cast CTs 100/50/1-1A withCore 1 : 7.5VA CL 1Core 2 : 7.5VA CL 5P10 |
| 646 | 3 Nos. PT - 11kV/√3//110/√3V ,CL 1.0, 50VA |
| 647 | Breaker Panel indication Lamps : |
| 648 | 6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged |
| 649 | Switches and other Accessories |
| 650 | 8 nos.Fuses |
| 651 | 1 No. Heater |
| 652 | 1 No. Thermostat |
| 653 | 1 No. 6 Window Annunciator |
| 654 | 1 No. Plug & Socket |
| 655 | 1 No. Test Terminal Block |
| 656 | 1 No. T-N-C Switch |
| 657 | 1 No. Emergency Push Button |
| 658 | 1 No. Local/Remote Selector Switch |
| 659 | 1 No. Hooter |
| 660 | Meters |
| 661 | 1 No. Analog Ammeter + ASS |
| 662 | 1 No. Analog Voltmeter + VSS |
| 663 | 1 No. Digital Multifunction Meter - Quasar |
| 664 | Relays |
| 665 | 1 No. MC 61A (O/C + E/F - IDMT+Inst) |
| 666 | 1 No. AVAJH13 Master trip relay (Ashida) |
| 667 | 1 No. TCS Relay |
| 668 | Three VCB Panel Board |
| 669 | 11KV PANEL BOARD NEAR TRANSFORMER |
| 670 | Design, manufacturer, supply of panel board fabricated out of minimum 2 mm thick sheet steel as per specifications. The panel shall be complete with cable termination arrangement suitable for incoming and outgoing each 1 run x 3C x 240 Sqmm XLPE 11 KV cable and copper bus bar arrangement. The panel shall comprise of the following: |
| 671 | Single Panel Board |
| 672 | Incomer:- |
| 673 | 1No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC |
| 674 | Each incomer comprising with following accessaries. |
| 675 | 1 No. Mechanical ON/OFF Indicator |
| 676 | 1 No. Aux Switch 6NO + 6NC |
| 677 | Panel, Busbar, CT, PT |
| 678 | 1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable |
| 679 | 3 Nos. Resin Cast CTs 100/50/1-1A withCore 1 : 7.5VA CL 1Core 2 : 7.5VA CL 5P10 |
| 680 | 3 Nos. PT - 11kV/√3//110/√3V ,CL 1.0, 50VA |
| 681 | Breaker Panel indication Lamps : |
| 682 | 6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged |
| 683 | Switches and other Accessories |
| 684 | 8 nos.Fuses |
| 685 | 1 No. Heater |
| 686 | 1 No. Thermostat |
| 687 | 1 No. 6 Window Annunciator |
| 688 | 1 No. Plug & Socket |
| 689 | 1 No. Test Terminal Block |
| 690 | 1 No. T-N-C Switch |
| 691 | 1 No. Emergency Push Button |
| 692 | 1 No. Local/Remote Selector Switch |
| 693 | 1 No. Hooter |
| 694 | 1 No. Power pack |
| 695 | 1 No. Surge Arrestor |
| 696 | Meters |
| 697 | 1 No. Analog Ammeter + ASS |
| 698 | 1 No. Analog Voltmeter + VSS |
| 699 | 1 No. Digital Multifunction Meter - Quasar |
| 700 | Relays |
| 701 | 1 No. MC 61A (O/C + E/F - IDMT+Inst) |
| 702 | 1 No. AVAJH13 Master trip relay (Ashida) |
| 703 | 1 No. TCS Relay |
| 704 | VCB Panel Board |
| 705 | 11KV/ 0.433KV 1600KVA OIL TYPE TRANSFORMER |
| 706 | Supplying ,Assembling , erecting, testing and commissioning of 1600 KVA 11KV/0.433KV voltage 3phase 50Hz, outdoor type copper wound, OIL type step down transformer complete with all modern fittings as given in the specifications including , lifting lugs, Roller type bi-directional wheels, suitable boxes on both the ends for cable entry/ bus duct,winding temprature indication & alarm, , earthing terminals,buchholz relay, diagram and rating plat etc. as required. |
| 707 | The transformers shall be installed in hot, humid tropical atmosphere. All equipment accessories and wiring shall be provided with tropical finish to prevent fungus growth |
| 708 | The transformers shall be oil Type & capable of continuous operation of rated output under the operating conditions of voltage and frequency variations as per statutory limits governed by relevant Indian Standard and Indian Electricity Rules, 1956 / IEC with latest amendments in force. |
| 709 | Requirement: 11KV/433V voltage oil type with OFF LOAD Tap Changer, Tapping range +7.5% to -15% in steps of 2.25% (HV side), oil cool ONAN |
| 710 | Voltage Ratio: No load voltage 11000/433volts within tolerance as stipulated in latest IS standard. |
| 711 | Rating: The transformer shall have a continuous rating as specified at any of the specified tapping position and with the maximum temperature rise specified. |
| 712 | Type of Load: The transformer shall be suitable for carrying unbalanced load up to 90% load within temperature rise indicated in the Indian Standard specification ‘Guide for loading of oil Transformer |
| 713 | Overloads: The transformers shall be suitable for carrying overload within temperature rise indicated in IS ‘Guide for Loading of oil Transformer |
| 714 | Connections: H.V. Delta and L.V Star connected with neutral brought out on the secondary side for connection to earth; Vector group DYn11 of IS:2026 |
| 715 | Each 11KV/433V Dual voltage Step down transformers shall be provided with the following fittings and accessories: Rating diagram and terminal marking plate for transformer. |
| 716 | Lifting lugs for transformer |
| 717 | Bi-directional Rollers |
| 718 | Rating diagram and terminal marking plate for transformer |
| 719 | Earth terminals (2 Nos) for body earthing for transformers |
| 720 | Inspection door for access to terminal connections for transformers |
| 721 | Suitable cable termination arrangement for M.V. side box with extended Bus bars for cables or Bus duct connection and cable box terminations on H.V. Side, suitable for 3C x 240/300sq. mm 11 K.V. XLPE Aluminum Conductor cable or sutable rating Busduct. |
| 722 | Necessary hardware, clamps, lugs etc. for terminations of H.V. Cables on HV side and cable termination on M.V. Side. |
| 723 | Winding temperature indicator with contacts for remote alarm and tripping. |
| 724 | DG SETS and BATTERY CHARGER |
| 725 | Supply, installation, testing & commissioning of 415 V, 320 kVA stand by rating ( radiator cooled type ) diesel generating set along with base frame, Alternator, Static Excitation System, Lube Oil System, Electronic Governor, Batteries, Battery Charger, Instrumentation, day oil fuel tank including the piping of approx. 12 mtr, Silencer with Bellows, Alarms, Engine Control Panel, AVM Pads, AVR Panel, Terminal Arrangements including bus duct termination box with all associated equipment / work as per specifications. Alternator shall have class-H insulation and rated for 680 KW output at 47deg. C. Engine shall not be derated upto 50 deg.C ambient. (First Fill oil of 990 litre for Day oil tnak to be considered in the offer). Supply and installation of suitabkle dia SS flexible bellows with matching flanges along with required hardware i.e. gasket, nut bolt, washer etc as required. |
| 726 | Supply, laying of following sizes of MS Piping for Exhaust including providing suitable bends, reducers & supporting arrangement at suitable intervals including insulation on entire length of exhaust pipe with 50mm thick Rockwool insulation & painting etc. as required. 250 mm dia |
| 727 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : |
| 728 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required |
| 729 | 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 730 | 120 mm dia (OD-120 mm & ID-103 mm nominal) |
| 731 | 160 mm dia (OD-160 mm & ID-135 mm nominal) |
| 732 | Supply of 7.0 Mtr High Octagonal pole ( Hot Dip Galvanized) BOP-7030 with top dia 70mm and bottom dia 130mm and made of 2mm thick base plate of size 200mmX200mmX12mm ( LXBXT) and with suitable size of foundation bolts and complete as required |
| 733 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 6.5 metre and upto 8 metre |
| 734 | Supply, installation, testing and commissioning of 35W Kwp power rating high efficiency eco friendly with compact ascesthic design Integrated all-in-one solar street light with system efficacy ≥ 170 lm/watt CRI>70 IP-65 complete with all accessories sush as lithium ferro phosphate battery, Mono crystalline solar panel and MPPT charger and built into sensor based luminaire made of Pressure die cast aluminium and suitable bracket for top pole mounting etc complete as required. |
| 735 | Supply of 12.0 Mtr High Mast in one section construction S355 grade as per BS-EN-10025 Top dia 100mm, bottom dia 360mm, plate thickness 3mm, 12side polygon, galvanosation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike lighting protection, maximum wind speed 47m/s as per IS :875 (part-III) with 6 nos. foundation bolt of PCD 445mm TS 600/24mm dia/850mm long luminaries carriage: material of 40NB ERW class B mM.S pipe dia of carriage ring 450mm (ID) with 8 arm, welded 2 section having carrying capacity upto 8 luminaries trailing cable 5core 2.5sq.mm PVC flexible copper conductor winch/power tool double drum SWL 350kg with 0.75HP 6pole single speed integral motor rope grade AISI:304, 7/19 construction dia 5mm BLC 1450x2 having 2nos. of continues rope. Aviation obstruction light twin dome aviation obstruction light LED type required. feeder pillar control panel housing 32a TPN MCB incoer single dial timer 25A contactor circuit for the automatic control of luminaries outgoing terminals and control circuit for power tool & Remote control. |
| 736 | For 120MT High mast : ITC of high mast light fixture with the help of suitable tools and plants wiring of luminaries with material like insulared PVC sheathed flexible cable of suitable copper conductor lugs MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil beaninh capacity of 10T/MT high mast. |
| 737 | Supply of following sizes sizes of PVC insulated PVC sheathed aluminium conductor armoured 1.1 KV grade as as required. |
| 738 | 2C x 6 sq mm |
| 739 | 2C x 10 sq mm |
| 740 | 2C x 16 sq mm |
| 741 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 742 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required Upto 35 sq. mm |
| 743 | Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade. |
| 744 | 2C x 6 sq mm |
| 745 | 2C x 10 sq mm |
| 746 | 2C x 16 sq mm |
| 747 | Supplying and fixing of outdoor type junction box( IP 67 ) suitable to incoming and outgoing up to 16 sq. mm Al Armoured Cable. The juction box shall also be suitable for 3 Nos. outgoing circuits each consisitng of 3 Nos. 2.5 sq mm copper wired wires |
| 748 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required. |
| 749 | Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required |
| 750 | LT CABLES |
| 751 | Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium / Copper conductor armoured cables as per specification as required. PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Aluminium conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1) |
| 752 | 3.1/2 core 300sq. mm. |
| 753 | 3.1/2 core 240sq. mm. |
| 754 | 3.1/2 core 185sq. mm. |
| 755 | 3.1/2 core 150sq. mm. |
| 756 | 3.1/2 core 120sq. mm. |
| 757 | 3.1/2 core 95sq. mm. |
| 758 | 3.1/2 core 70sq. mm. |
| 759 | 3.1/2 core 50sq. mm. |
| 760 | 3.1/2 core 35sq. mm. |
| 761 | 3.5 core 25sq. mm. |
| 762 | 4 core 16sq. mm. |
| 763 | 4 core 10 sq. mm. |
| 764 | 4 core 6 sq. mm. |
| 765 | PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Copper conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1) |
| 766 | 4 core 1.5 sq. mm. ( Copper Control cable) |
| 767 | 7 core 1.5 sq. mm. ( Copper Control cable) |
| 768 | 12 core 1.5 sq. mm. ( Copper Control cable) |
| 769 | Layrng and fxing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. |
| 770 | Upto 35 sq. mm |
| 771 | Above 35 sq. mm and upto 95 sq. mm |
| 772 | Above 95 sq. mm and upto 185 sq. mm |
| 773 | Above 185 sq. mm and upto 400 sq. mm |
| 774 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 775 | Upto 35 sq. mm |
| 776 | Above 35 sq. mm and upto 95 sq. mm |
| 777 | Above 95 sq. mm and upto 185 sq. mm |
| 778 | Above 185 sq. mm and upto 400 sq. mm |
| 779 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required |
| 780 | Upto 35 sq. mm |
| 781 | Above 35 sq. mm and upto 95 sq. mm |
| 782 | Above 95 sq. mm and upto 185 sq. mm |
| 783 | Above 185 sq. mm and upto 400 sq. mm |
| 784 | Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade. |
| 785 | 3.1/2 core 300sq. mm. |
| 786 | 3.1/2 core 240sq. mm. |
| 787 | 3.1/2 core 185sq. mm. |
| 788 | 3.1/2 core 150sq. mm. |
| 789 | 3.1/2 core 120sq. mm. |
| 790 | 3.1/2 core 95sq. mm. |
| 791 | 3.1/2 core 70sq. mm. |
| 792 | 3.1/2 core 50sq. mm. |
| 793 | 3.1/2 core 35sq. mm. |
| 794 | 4 core 25sq. mm. |
| 795 | 4core 16sq. mm. |
| 796 | 4 core 10sq. mm. |
| 797 | 4 core 6sq. mm. |
| 798 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Powder coated shall be of Siemens Grey Colour- RAL 7032) |
| 799 | 100mm width X 50mm depth X 1.6 mm thickness |
| 800 | 150mm width X 50mm depth X 1.6 mm thickness |
| 801 | 300mm width X 50mm depth X 1.6 mm thickness |
| 802 | 450mm width X 50mm depth X 2.0 mm thickness |
| 803 | 600mm width X 62.5mm depth X 2.0 mm thickness |
| 804 | 750mm width X 75mm depth X 2.0 mm thickness |
| 805 | 900mm width X 75mm depth X 2.0 mm thickness |
| 806 | 11KV HT CABLE |
| 807 | Supply of cable XLPE -PVC insulated PVC sheathed galvanised steel strip armoured electric power cable with aluminium conductor 11000 volt grade of size 3CX300 sqmm. |
| 808 | Laying of one number XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm |
| 809 | Laying of one number XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 120 sq. mm and upto 400 sq. mm |
| 810 | Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 300 sq. mm |
| 811 | Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 33 KV grade as required : 300 sq. mm |
| 812 | Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium / Copper conductor armoured cables as per specification as required. PVC/ XLPE insulated PVC sheathed heavy duty, armoured electrical cables with Aluminium conductor for working voltage upto and including 1100volts ( conforms to IS:1554, Part-1) |
| 813 | 3.1/2 core 120sq. mm. |
| 814 | 3.1/2 core 50sq. mm. |
| 815 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 816 | Above 35 sq. mm and upto 95 sq. mm |
| 817 | Above 95 sq. mm and upto 185 sq. mm |
| 818 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size cables in the existing RCC/ HUME/ Stoneware/ Metal pipe as required Upto 35 sq. mm |
| 819 | Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade. |
| 820 | 3.1/2 core 120sq. mm. |
| 821 | 3.1/2 core 50sq. mm. |
| 822 | 4 core 10sq. mm. |
| 823 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Powder coated shall be of Siemens Grey Colour- RAL 7032) |
| 824 | 100 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 825 | 150 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 826 | Providing and fixing 6 SWG dia. GI wire on surface or in recess for loop earthing along with the existing surface / recessed conduits / submain wiring / cable as required. |
| 827 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc, as required |
| 828 | MAIN LT PANEL CUM CHANGE OVER PANEL ( 50 kA ) |
| 829 | Incoming Air Circuit Breaker from TRF |
| 830 | 1 nos. 2500 amps 4 pole electrically operated manually draw out type air circuit breaker each with following accessories : |
| 831 | Digital energy meter (Schneider – EM6400NG or equivalent) of accuracy class-1, with 3 Nos. 2500 amps 15VA CTs. |
| 832 | Phase indicating light shall be protected by suitable rating MCB’s. - 3 Sets |
| 833 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 834 | 24 V DC Shunt trip coil. - 1 Set |
| 835 | 240 V under voltage release. - 1 Set |
| 836 | Auto-manual / test selector / switch - 1 Set |
| 837 | Breaker control switch - 1 Set |
| 838 | IDMT relay- 1 Set |
| 839 | Under Volate & Over Voltage relay |
| 840 | Master trip relay- 1 Set |
| 841 | Auxiliary contacts required for necessary interlocking of breakers. |
| 842 | Bus Bars |
| 843 | 3200 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 844 | Outgoing |
| 845 | 2 Nos. 1000 Amps TPN Pole manually operated fully drawout type air circuit breaker and ON/OFF/Trip & shunt trip coil. |
| 846 | 2 Nos. 800 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil. |
| 847 | 6 Nos. 500/630 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil. |
| 848 | 7 Nos. 400 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil. |
| 849 | 5 Nos. 315 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil. |
| 850 | 7 Nos. 250 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil. |
| 851 | 6 Nos. 200 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil. |
| 852 | 7 Nos. 100/125/160 Amps TPN POLE MCCB and ON/OFF/Trip & shunt trip coil. |
| 853 | Note: |
| 854 | All breakers shall be electrically interlocked |
| 855 | All ACB’s/MCCB’s shall be suitable for 50 kA breaking capacity. |
| 856 | PLC for load management , interlocking , DG auxiliary and supervision. |
| 857 | 2 kVA UPS for 30 MinutesBackup for control wiring. |
| 858 | Touch screen display panel having 10.4 inch - TFT Display - Color screen as per specification. |
| 859 | Auto starting / Auto synchronizing / Auto load balancing and auto load management panel for 2 No. DG Sets |
| 860 | All outgoing feeder shall have digital electronic energy meter ( EM 6438 of conzerv make or equivalent ) with suitable no. of CT,s and RS 485 port . |
| 861 | 1 No. --/ 5, 15 VA dual ratio CT’s shall be provided for APFCR on each transformer's incomer. |
| 862 | Wiring and supply, installation of space heater, Humidistatae and control MCB’s shall be provided all vertical sections. |
| 863 | Suitable danger board shall be provided. |
| 864 | All bus bar section / backside panels shall have hinged type door. |
| 865 | 9 W fitting with LED lamp, switch shall be provided in each vertical section. |
| 866 | Incomer ACB receiving power from transformer/D.G shall have suitable provision for Cables connection.. |
| 867 | All Electronic Energy meter shall be pre wired for BMS connection upto central point within the panel with sheilded cable. |
| 868 | All incoming & outgoing feeders shall have minimum 4 nos. potential free contacts. |
| 869 | 1No. 24V DC Supply Power Pack with suitable (bidder shall provide the Ah calculation) Ah Maintenance free Battery back up. Power Pack should be with Protections of over voltage/ under voltage/ over charging. |
| 870 | 450KVAR CAPACITOR PANEL |
| 871 | INCOMER |
| 872 | Direct From MLP |
| 873 | METERING & INDICATION |
| 874 | 1 set of phase indicating lamps |
| 875 | 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB |
| 876 | 1 No. 12 steps APFC relay |
| 877 | 1 set of Ammeter (0-1200A) with ASS and 3 nos.600/5A, CTs' |
| 878 | BUS-BAR |
| 879 | 1 Set of 1500A TPN Aluminium Bus Bar with colour coded PVC Sleeves |
| 880 | OUTGOINGS |
| 881 | 4 Nos.of 125A TP MCCB (35 KA) with 140A TP contactor (AC-3 duty) |
| 882 | 7 Nos. of 100A TP MCCB (35 KA) with 70A TP contactor (AC-3 duty) |
| 883 | 1 No. of 63A TP MCCB (35 KA) with 40A TP contactor (AC-3 duty) |
| 884 | 4 Nos. of 32A TP MCCB (35 KA) with 20A TP contactor (AC-3 duty) |
| 885 | 3 No.of 16A TP MCCB (35 KA) with 10A TP contactor (AC-3 duty) |
| 886 | All bank having self Illuminated Red-Green (ON-OFF) push buttons. |
| 887 | 4 Nos. 50 KVAR capacitor Bank with discharge resistor. |
| 888 | 7 Nos. 25 KVAR capacitor Bank with discharge resistor. |
| 889 | 1 No. 20 KVAR capacitor Bank with discharge resistor. |
| 890 | 4 No. 10 KVAR capacitor Bank with discharge resistor. |
| 891 | 3 No. 5 KVAR capacitor Bank with discharge resistor. |
| 892 | Supply Receiving, fixing, testing & commissioning of of Capacitor panel as described above |
| 893 | STAFF QUARTER METER BOARD |
| 894 | Incoming |
| 895 | 1 No. 250. Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 896 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 250/5 amps 15VA CTs. |
| 897 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 898 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 899 | Bus Bars |
| 900 | 400 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 901 | Outgoing |
| 902 | 34 No.63 Amps FP Pole MCB. |
| 903 | 32 No. 2ph 2 wire Prepaid Meter. |
| 904 | Panel as described above. |
| 905 | PRINCIPAL QUARTER METER BOARD |
| 906 | Incoming |
| 907 | 1 No.63 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 908 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 909 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 910 | 1 No. 3ph 4 wire Prepaid Meter. |
| 911 | Bus Bars |
| 912 | 300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 913 | Outgoing |
| 914 | 3 No.40 Amps FP Pole MCB. |
| 915 | Panel as described above. |
| 916 | STUDENT RESOURCE CENTRE MDB |
| 917 | 1 No.315 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 918 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 300/5 amps 15VA CTs. |
| 919 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 920 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 921 | Bus Bars |
| 922 | 300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 923 | Outgoing |
| 924 | 9 No.63/100/125Amps TPN MCCB and ON/OFF/Trip & shunt trip coil. |
| 925 | Panel as described above. |
| 926 | DEGREE COLLEGE MDB |
| 927 | 2 nos. 800 amps 4 pole electrically operated manually draw out type air circuit breaker each with following accessories : |
| 928 | Digital energy meter (Schneider – EM6400NG or equivalent) of accuracy class-1, with 3 Nos. 1000 amps 15VA CTs. |
| 929 | Phase indicating light shall be protected by suitable rating MCB’s. - 3 Sets |
| 930 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 931 | Bus Bars |
| 932 | 1250 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 933 | Bus Coupler |
| 934 | 1000 amps 4 pole electrically operated manually drawout type air circuit breaker, with ON / OFF / TRIP indicating lamps with control MCB’s, shunt trip. |
| 935 | Outgoing |
| 936 | 2 No.630Amps TPN MCCB and ON/OFF/Trip & shunt trip coil. |
| 937 | 2 No.400/500Amps TPN MCCB and ON/OFF/Trip & shunt trip coil. |
| 938 | 5 No.315Amps TPN MCCB and ON/OFF/Trip & shunt trip coil. |
| 939 | 4 No.125Amps TPN MCCB and ON/OFF/Trip & shunt trip coil. |
| 940 | 2 No.63Amps TPN MCCB and ON/OFF/Trip & shunt trip coil. |
| 941 | Panel as described above. |
| 942 | DEGREE COLLEGE SDB |
| 943 | 1 No.400/500 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 944 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 300/5 amps 15VA CTs. |
| 945 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 946 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 947 | Bus Bars |
| 948 | 500 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 949 | Outgoing |
| 950 | 6 No.63/100/125Amps TPN MCCB and ON/OFF/Trip & shunt trip coil. |
| 951 | Panel as described above. |
| 952 | LIFT PANEL |
| 953 | Incoming |
| 954 | 1 No. 125 Amps with 4 Pole MCCB with 125A ATS and ON/OFF/Trip |
| 955 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 120/5 amps 15VA CTs. |
| 956 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 957 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 958 | Bus Bars |
| 959 | 300 amps TPN Aluminium bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 960 | Outgoing |
| 961 | 2 No. 40/63 Amps 4 Pole MCCB and ON/OFF/Trip |
| 962 | 2 No. 32/25 Amps FP Pole MCB. |
| 963 | Panel as described above. |
| 964 | UPS MDB DEGREE/ADMIN COLLEGE BLOCK |
| 965 | Incoming |
| 966 | 1 No.250/315 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 967 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 250/315/5 amps 15VA CTs. |
| 968 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 969 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 970 | BUSCUPLER |
| 971 | 1 No.250/315 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 972 | Bus Bars |
| 973 | 400 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 974 | Outgoing |
| 975 | 9 No.63/100/125 Amps TPN Pole MCCB. |
| 976 | Panel as described above. |
| 977 | EXTERNAL LIGHTING FEEDER PILLAR OUT DOOR TYPE |
| 978 | INCOMER |
| 979 | 1 Nos. 63/100Amp 16KA 4P MCCB complete having microprocessor based over current, short circuit & earth fault protection incomer shall be complete with following. |
| 980 | 1 Nos. 60Amp AC3 4P Contactor with timer be complete as required. |
| 981 | METERING FOR EACH INCOMER |
| 982 | Square flush mounting 0-60Amp ammeter with 3 way and OFF selector switch. |
| 983 | 3 Nos. Cast resin current transformers of Class 1.0 for metering. |
| 984 | Three phase indicating lamps (LED type) with MCB. |
| 985 | ON OFF TRIP indicating lamps (LED type). |
| 986 | Square flush mounting voltmeter 0-500 volt with 3 way and OFF selector switch. |
| 987 | BUSBAR |
| 988 | 1 Set of 100A, TPN Aluminum bus bars with colour coded sleeves. |
| 989 | OUTGOING UNITS |
| 990 | 10 Nos. 6/32Amp TPN MCB 10KA |
| 991 | EXTERNAL LIGHTING FEEDER PILLAR AS DESCRIBED ABOVE |
| 992 | EM. D.G PANEL |
| 993 | INCOMER |
| 994 | 1 No.500 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 995 | 1 No.500 Amps 4 Pole ATS |
| 996 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 500/05 amps 15VA CTs. |
| 997 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 998 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 999 | Bus Bars |
| 1000 | 400 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 1001 | Outgoing |
| 1002 | 1 No.315 Amps TPN Pole MCCB. |
| 1003 | 2 No.200/250 Amps TPN Pole MCCB. |
| 1004 | 1 No.125 Amps TPN Pole MCCB. |
| 1005 | 3 No.63/100 Amps TPN Pole MCCB. |
| 1006 | MDB AS DESCRIBED ABOVE |
| 1007 | EM. PANEL DEGREE COLLEGE |
| 1008 | INCOMER |
| 1009 | 1 No.250 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 1010 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 250/05 amps 15VA CTs. |
| 1011 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 1012 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 1013 | Bus Bars |
| 1014 | 300 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 1015 | Outgoing |
| 1016 | 5 No.125 Amps TPN Pole MCCB. |
| 1017 | 3 No.63/100 Amps TPN Pole MCCB. |
| 1018 | PANEL AS DESCRIBED ABOVE |
| 1019 | EM. PANEL SCR |
| 1020 | INCOMER |
| 1021 | 1 No.100/125 Amps 4 Pole MCCB and ON/OFF/Trip & shunt trip coil. |
| 1022 | Digital energy meter (conzerve – EM 6400NG with RS-485 or equivalent) of accuracy class-I, with 3 Nos. 100/05 amps 15VA CTs. |
| 1023 | Phase indicating light shall be protected by suitable rating MCB’s.- 3 Sets |
| 1024 | Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set |
| 1025 | Bus Bars |
| 1026 | 300 amps 4P Copper bus bars with colour coded heat shrinkable insulating sleeves - 1 Set. |
| 1027 | Outgoing |
| 1028 | 5 No.63/100 Amps TPN Pole MCCB. |
| 1029 | PANEL AS DESCRIBED ABOVE |
| 1030 | VI EARTHING & LIGHTING PROTECTION |
| 1031 | Earthing with G.I. Earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. ( with charcoal or coke and salt). |
| 1032 | Earthing with copper . Earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.( with charcoal or coke and salt). |
| 1033 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required. |
| 1034 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 1035 | Providing and fixing 25x5 mm copper strip in 40mm dia G. I. pipe from earth electrode including connection with brass nut, bolt, spring washer excavation and re-filling etc. as required. |
| 1036 | S/L 25x6mm G.I. earth strip in ground: Proving and laying earth connection from earth electrode with 25x6mm G.I wire in 15mm GI pipe from electrode as required. |
| 1037 | Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. |
| 1038 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 1039 | Providing and fixing 32 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required. |
| 1040 | Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required. |
| 1041 | Providing and fixing 50 mm X 6 mm Cu, strip on surface or in recess for connections etc. as required. |
| 1042 | CU WIRE CONDUCTORS |
| 1043 | Providing and laying following size CU insulated wire on surface or in recess in exising conduit/ cable tray for connections etc. as required. |
| 1044 | 6sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor |
| 1045 | 10sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor |
| 1046 | 16sqmm ISI marked, FRLS PVC insulated, 1 core copper conductor |
| 1047 | LIGHTNING PROTECTION |
| 1048 | Prividing and Fixing of GI lightning conductor Finial made of 25mm dia 300 mm Long GI tube , having single prone on top with 85mm dia 6mm thick GI base plate including holes etc complete as required |
| 1049 | Providing and fixing GI-tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor as required.(for vertical run) |
| 1050 | Providing and fixing GI-tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor as required.(for horizontal) |
| 1051 | Providing and fixing testing joint, made of 20 mm x 3 mm thick gi strip, 125 mm long with 4 Nos. brass bolts, nuts check nuts and spring washers etc. complete as required. |
| 1052 | Providing and laying GI tape, 32 mm x 6 mm thick from earth electrode directly in ground as required. |
| 1053 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 1054 | SUPPLY AND INSTALLATION OF LIGHT FIXTURES AND EXHAUST FANS |
| 1055 | SITC of following ratings LED Flood lighting luminaire with pressure dia cast housing and toughned glass cover IP 66 protection) in existing pole / pipe for supply voltage 100 ,270v AC , 5o HZ luminaire shall be confirm to IS 10322 part 5/ section 3e and shall be complete with all necessary accessories as required 45W LED STREET LIGHT |
| 1056 | SITC of following ratings LED Flood lighting luminaire with pressure dia cast housing and toughned glass cover IP 66 protection) in existing pole / pipe for supply voltage 100 ,270v AC , 5o HZ luminaire shall be confirm to IS 10322 part 5/ section 3e and shall be complete with all necessary accessories as required 50/60W LED FLOOD LIGHT |
| 1057 | SITC of following ratings RECCESS /SURFACE MOUNTED LED ROUND / SQUIRE SHAPE DOWN LIGHT liminiaire with pressure dia cast housing FOR SINLE PHASE supply voltage luminaire shall be confirm to IS 10322 Part 3 section 2 or IEC 6-7 22 with all necessary accessory item required . |
| 1058 | 10/12 W LED ROUND SURFACE DOWNLIGHT STAIR LIGHT |
| 1059 | 10/12w LED RECESSED ROUND DOWNLIGHT |
| 1060 | 6w LED SURFACE BULK HEAD LIGHT |
| 1061 | 2'x2' LED PANEL LIGHT |
| 1062 | 10/12w LED SURFACE ROUND DOWNLIGHT |
| 1063 | 10/12w LED WALL LIGHT |
| 1064 | 28w LED RECESSED BATTEN LIGHT |
| 1065 | 50w LED RECESSED DOWN LIGHT |
| 1066 | SITC of following ratings SURFACE MOUNTED LED tube light fitting, suitable for 230V 50Hz, single phase supply etc. complete as required. |
| 1067 | 10/12W LED Tube light |
| 1068 | 20/22W LED Tube light |
| 1069 | SITC of following ratings LED Post top lamp made in dia cast aluminium housing with decorative clear/ opal acrylic diffuse on existing pipe including connection with 1.5sq mm copper conductor etc all complete as required. 20/25W LED post top lamp clear |
| 1070 | SITC of following ratings approved make LED Bollard fitting, with rectangular shape of height 600 to 850mm power input 8/9 watt with dia cast aluminium housing opel with PC diffuser, [P:65/54 protection, confirming to IS:10322 part 5 etc all complete as required (excluding plinth charge) |
| 1071 | LED strip light 24 volts DC with IP 65 rated in different colours of length 5 mtr and power 5 W per meter including driver IS: 10322 pert 5/ section-7. |
| 1072 | Supply of LED Mirror Light with power 8/10W rated voltage 230V 50 Hz aluminium/ PC body with rauuning life minimum 30000 Hours |
| 1073 | Supply insttalation , testing and commisioning of following size ceiling fan 3 balde confirming to IS : 374:2019 incuding wiring thedown roads of standed lenth ( upto 30 cm ) with 1.5 sqmm PR PVC, insulated copper wire suitable for 230V 50Hz single phase supply etc. compleyte as required. 1200mm (48 Degree) BLDC 5 star rating 32W ceiling fan |
| 1074 | Supply and fixing of step type electronic fan regulator on existing modular plate switch box including connection but excluding modular plate etc as required. |
| 1075 | Installation, testing and commissioning of ceiling fans/bracket fan of all sizes including wiring the down rod .of standard length (up to 30 cm ) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required. |
| 1076 | Supply of 12\\" (300mm) metal exhaust fan |
| 1077 | Supply of 16\\" (400mm) metal exhaust fan |
| 1078 | TELEPHONE, TV , DATA cabling with Raceways : |
| 1079 | Supply & fixing of modular telephone cord outlet & switch box including connections but excluding modular plate etc. as required. |
| 1080 | Supply & fixing of modular TV antenna socket outlet & switch box including connections but excluding modular plate etc. as required. |
| 1081 | S/F Modular boxes, base & cover plate :- Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required. I or 2 module (78mmx 78mmx 45mm) |
| 1082 | Supplying and fixing of following size PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification. |
| 1083 | 20mm dia |
| 1084 | 25mm dia |
| 1085 | 32mm dia |
| 1086 | Supply and fixing 1 or 2 module ( 75mm X 75mm ) GI Box along with modular base and cover plate for modular switches in recess etc as required |
| 1087 | Supply and fixing of Computer terminal (RJ-45) outlet in existing box with modular plate |
| 1088 | Supply and fixing of Outdoor type junction Box |
| 1089 | Supply and Laying of Cat-6 Cable in existing conduits |
| 1090 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm copper conductor PE insulated, with PVC shield in the existing surface/ recessed PVC conduit as required. |
| 1091 | Supplying, drawing, of 0.5mm dia (2 pair) FR PVC insulated copper conductor , unarmoured telephone cable in existing surface/ recessed PVC conduit as required |
| 1092 | Supplying, drawing, of 0.5mm dia (4 pair) FR PVC insulated copper conductor , unarmoured telephone cable in existing surface/ recessed PVC conduit as required |
| 1093 | Supplying and Fixing in floor with all accessories , 2 mm thick steel sheet factory fabricated post galvanized floor recessed raceway of the following sizes |
| 1094 | 225 mm wide x 38 mm deep raceway |
| 1095 | 100 mm wide x 38 mm deep raceway |
| 1096 | Providing and fixing 400 x 400 x 50 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required |
| 1097 | Providing and fixing 300 x 300 x 50 mm deep 2 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required |
| 1098 | Providing and fixing 150 x 150 x 50 mm deep 1.6 mm thick GI sheet junction box including providing 3 mm thick stainless steel cover as required |
| 1099 | FIRE ALARM AND DETECTION SYSTEMS |
| 1100 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the samein case of recessed conduit as required. |
| 1101 | 20mm dia |
| 1102 | 25mm dia |
| 1103 | Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required. |
| 1104 | 2x1.5 sq mm |
| 1105 | 2x2.5 sq mm |
| 1106 | Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log andfacility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. Ten Loop Panel |
| 1107 | Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. |
| 1108 | Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required. |
| 1109 | Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. |
| 1110 | Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. |
| 1111 | Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required. |
| 1112 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 1113 | Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required. |
| 1114 | Supplying, installation, testing & commissioning of addressable fire control module complete as required. |
| 1115 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. |
| 1116 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. |
| 1117 | FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) |
| 1118 | Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. |
| 1119 | Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. |
| 1120 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. |
| 1121 | Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone |
| 1122 | PA SYSTEM |
| 1123 | Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.. |
| 1124 | Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required. |
| 1125 | Supplying, installing, testing and commissioning of 2X1.0 SQMM IND. 1.1KV SPEAKER CABLE in existing conduit. |
| 1126 | Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required. |
| 1127 | Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required. |
| 1128 | Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required. |
| 1129 | Supplying, installation, testing & commissioning of exit point directional sound speaker with voice and integral audio amplifier with selectable sound pulse patterns complete as required. |
| 1130 | Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required. |
| 1131 | Providing and fixing of self illuminated / auto glow \\"EXIT\\" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 300 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site |
| 1132 | INTERNAL WIRING AND FINAL DISTRIBUTION BOARDS |
| 1133 | Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit , with modular switch ,modular plate ,suitable GI box as required |
| 1134 | Group - B |
| 1135 | Group - C |
| 1136 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. |
| 1137 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 1138 | S.P 5/6 amps, one way modular switch, ISI Marked |
| 1139 | S.P 15/16 amps, one way modular switch, ISI Marked |
| 1140 | 5 pin 5/6 amps, modular socket Outlet, ISI Marked |
| 1141 | 6 pin 15/16 amps, modular socket Outlet, ISI Marked |
| 1142 | Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 1143 | Supplying and fixing 20/25 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps “C” curve, TP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 1144 | Supplying and fixing Brass Batten/ Angle holder including connections etc. as required. |
| 1145 | DB SUBMAIN WIRING IN STEEL CONDUITS |
| 1146 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. |
| 1147 | 2 X1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre |
| 1148 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre |
| 1149 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre |
| 1150 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre |
| 1151 | 2 X 10 sq. mm + 1 X 6 sq. mm earth wire Metre |
| 1152 | 2 X 16 sq. mm + 1 X 6 sq. mm earth wire Metre |
| 1153 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire Metre |
| 1154 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre |
| 1155 | 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre |
| 1156 | POWER SOCKETS |
| 1157 | Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch,connection, painting etc.as required. |
| 1158 | Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 6 pin 15 / 16 modular socket outlet and 15 / 16 amps modular switch,connection,painting etc.as required. |
| 1159 | FINAL DISTIRIBUTION BOARD |
| 1160 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator) |
| 1161 | 8 way Double Door |
| 1162 | 12 way Double Door |
| 1163 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But withoutMCB/RCCB/Isolator) |
| 1164 | 6 way Double Door |
| 1165 | 8 way Double Door |
| 1166 | 12 way Double Door |
| 1167 | Supplying and fixing of following ways surface/ recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) asrequired . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) |
| 1168 | 6 way Double Door |
| 1169 | 12 way Double Door |
| 1170 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 1171 | 6/32 SP |
| 1172 | 6/32A DP |
| 1173 | 40A TPN |
| 1174 | 50/63A TPN |
| 1175 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. asrequired. |
| 1176 | 16/25 Amps |
| 1177 | Providing and fixing following rating and breaking capacity and 4 pole MCB with thermomagnetic release and terminal spreaders with cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required 25-63A 16KA fixed thermal setting |
| 1178 | IP BASED CCTV SYSTEM |
| 1179 | Supply, installation, testing and commissioning of UL Listed 1.3 Megapixel CMOS Vandal-proof, Network Dome Camera (1280 × 960) resolution, 1/3” Progressive scan CMOS, [email protected], AGC ON. 0 Lux with IR on, IR cut filter with auto switch, IR range up to 30 mtrs, H.264 / MJPEG, Dual stream, motion detection, Bit rate 32 Kbps-16Mbps, 3D DNR, DWDR, 12 VDC ± 10%, PoE , IP66, K-10, with fixed lens between (2.5 - 12mm), size of lens shall be as per site requirement & mockup. ONVIF, SIP, NMS, Profile S supported, connectors complete as required in dome shape fixed type for mounting recessed in false ceiling or mounted on wall complete as required. |
| 1180 | Supply, installation, testing and commissioning of UL Listed 1.3 Megapixel CMOS, Vandal-proof, Network Bullet Camera,(1280x960)resolution, 1/3” Progressive scan CMOS, [email protected], AGC ON. 0 Lux with IR on, IR cut filter with auto switch,, H.264 / MPEG4 , Dual stream, Bit rate 32 Kbps-16Mbps, Standard IP66, PoE , with Fixed Lens between (2.5 - 12mm), size of lens shall be as per site requirement & mock-up ,IR range Up to 50 mtr, motion detection, with ONVIF, SIP, NMS, Profile S supported, connectors complete as required IR Bullet fixed type for mounting on wall or surface mounted with back box and adapter plate complete as required. |
| 1181 | Supply, installation, testing and commissioning of Professional Video management and recording software and hardware comprising 32Ch. NVR to record output of all cameras mentioned above in Item no 1,2,3 Third-party network cameras supported, H.264 Compression - Up to 5 Megapixels resolution recording, multiple Hard Disk 8 SATA with each having maximum storage capacity of 6 TB , as required for minimum 30 days recording required for recording when in 80% motion @ 720p 25 Frames per second(Real Time) or for recording when not in motion @720p 12.5 Frames per second, with RAID-5 Storage ,10/100/1000 MBps network interface with each NVR, 2 USB2.0, HTTP Networkable, backup by USB/DVDWR, required Client software included, 6 Nos Client licenses and required Camera licenses for each camera complete as required. All the components to be of same make as Camera. |
| 1182 | Supply,installation,testing and commissioning of 32” CCTV colour LED screen including all accessories complete as required. |
| 1183 | Supply, installation, testing and commissioning of Layer 3 switch HP/ Cisco make with 16 ports PoE managed, 10/100/1000 EB core switches to support all IP cameras & Access Control System , with 2 Fibre uplinks Port module only complete as required. |
| 1184 | Supply, installation, testing and commissioning of Layer 2 switch HP/ Cisco make with 32 ports PoE managed, 10/100/1000 EB core switches to support all IP cameras & Access Control System , with 2 Fibre uplinks Port module only complete as required. |
| 1185 | Supplying and installation of 19\\" 42U APW President Rack with glass front door, steel rear door, power supply, MCB, cable manager, drawer shelves and wiring channels to accommodate systems equipment and accessories as mentioned in the BOQ above and including all connections and terminations as required |
| 1186 | Supply and Laying of Cat-6 Cable in existing conduits for Cameras |
| 1187 | Supply and Laying of 3C-2.5 Sq. mm unarmoured copper Power Cable in existing conduits for Cameras power supply |
| 1188 | Supply and Laying of 3C-1.5 Sq. mm unarmoured copper Power Cable in existing conduits for Cameras power supply |
| 1189 | Supplying and fixing of following size PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification. |
| 1190 | 20mm dia |
| 1191 | 25mm dia |
| 1192 | 32mm dia |
| 1193 | UPS/INV/SOALR SYSTEM |
| 1194 | 1550VA sine wave inverEr input AC range.1fi)V to 300V AC, wide- 90V to 300V AC, standard - 180V to 260V AC, DC range - 10.5 to 14.2 efficiancv- 80%, protection-overload, Short circuit |
| 1195 | Trolly for Double tubular Battery |
| 1196 | 200Ah tubular Lead acid battery with 36 month replacement guaranty. IS:1652:1991 |
| 1197 | 3000VA sine wave inverter input AC range-1O0V to 300V AC, wide- 90V to 300V AC, standard - 180V to 260V AC, DC range -1.0.5 toL4.2, efficiancv- 80%, protection-overload, Short circuit |
| 1198 | Trolly for Double tubular Battery |
| 1199 | 200Ah tubular Lead acid battery with 36 month replacement guaranty. IS:1652:1991 |
| 1200 | Supply,Installation, Commissioning & Training of 40 KWp Grid Connected Rooftop Solar Photovoltaic System based on heterojunction technology solar PV module as per requirment. including all expenses (to be borne by bidder) e.g. Air Fare, Local Transport, accommodation etc. |
| 1201 | UPS SETS |
| 1202 | Supply, testing and commissioning of 80KVA UPS SET frame with TRUE ONLINE double conversion VFI Technology UPS (High frequency PWM using IGBT technology), low losses, energy saver system, 3 Phase AC input & 3 Phase AC output fully microprocessor based UPS system suitable for 400 VAC, +10% -15%, 50 Hz supply, variation +/- 1%, Out put Power Factor- 1.0 and consisting of following:- |
| 1203 | Standards: IEC 62040- 1/ 2 & 3 |
| 1204 | Latest Transformer Less IGBT design UPS. |
| 1205 | Input range should be 320 VAC – 480 VAC. |
| 1206 | Efficiency >99% |
| 1207 | With Static by-pass |
| 1208 | 12 Pulse Rectifier with 11th harmonics filter, to achieve less than 3% total harmonic distortion with UPS. |
| 1209 | Fully microprocessor Digital Signal Processing (DSP) based with diagnostics capability . |
| 1210 | Input phase reversal correction without switchover to battery & it should work on normal operation. If not, suitable switchgear to be provided to correct the phase sequence. (Bidder to provide the diagram). |
| 1211 | Dual Input (Separate Input for rectifier and separate input for Bypass). |
| 1212 | Maintenance by-pass module. |
| 1213 | Microprocessor based LCD display indication for various parameter's display & LED indication for alarm for major status parameters and provisions for remote indications. |
| 1214 | The system shall be as per detailed specifications and shall be complete with all connections / inter-connections & provisions for static bypass etc. with required accessories as required. |
| 1215 | 65 Ah flat type Lead acid battery with 24 month replacement guaranty. IS:1652:1991 |
| 1216 | MS battery rack suitable for 40 to 50 UPS Battery installation |
| 1217 | Supply, testing and commissioning of 30KVA UPS SET frame with TRUE ONLINE double conversion VFI Technology UPS (High frequency PWM using IGBT technology), low losses, energy saver system, 3 Phase AC input & 3 Phase AC output fully microprocessor based UPS system suitable for 400 VAC, +10% -15%, 50 Hz supply, variation +/- 1%, Out put Power Factor- 1.0 and consisting of following:- |
| 1218 | Standards: IEC 62040- 1/ 2 & 3 |
| 1219 | Latest Transformer Less IGBT design UPS. |
| 1220 | Input range should be 320 VAC – 480 VAC. |
| 1221 | Efficiency >99% |
| 1222 | With Static by-pass |
| 1223 | 12 Pulse Rectifier with 11th harmonics filter, to achieve less than 3% total harmonic distortion with UPS. |
| 1224 | Fully microprocessor Digital Signal Processing (DSP) based with diagnostics capability . |
| 1225 | Input phase reversal correction without switchover to battery & it should work on normal operation. If not, suitable switchgear to be provided to correct the phase sequence. (Bidder to provide the diagram). |
| 1226 | Dual Input (Separate Input for rectifier and separate input for Bypass). |
| 1227 | Maintenance by-pass module. |
| 1228 | Microprocessor based LCD display indication for various parameter's display & LED indication for alarm for major status parameters and provisions for remote indications. |
| 1229 | The system shall be as per detailed specifications and shall be complete with all connections / inter-connections & provisions for static bypass etc. with required accessories as required. |
| 1230 | 65 Ah flat type Lead acid battery with 24 month replacement guaranty. IS:1652:1991 |
| 1231 | AC WORK |
| 1232 | Supply, testing and commissioning of 1.5Tr. 5 Star split A.C (Inverter Type) IS-1391-part-1 |
| 1233 | Supply, testing and commissioning of 2.0Tr. S Star Split A.C (hiverter Type) IS-1391-part-l |
| 1234 | Supply, testing and commissioning of Copper Tube of size l I 4 '' for split ac unit 1 /l.5/2/3 tr capac:ty nitride rubber insul;1tion |
| 1235 | 4 KVA wall mounted .:iutom;ltic voltage STABLIZER from range HOV to 28OV |
| 1236 | Supply, testing and commissioning of Drain pipe for ac |
| 1237 | Supply, testing and commissioning of Outdoor stand for 1.5Tr Split AC |
| 1238 | Supply, testing and commissioning of Outdoor stand for 2.0Tr Split AC |
| 1239 | HORTICULTURE WORK |
| 1240 | Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment). |
| 1241 | Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment) |
| 1242 | Screened through sieve of IS designation 20 mm |
| 1243 | Screened through sieve of IS designation 16 mm |
| 1244 | Screened through sieve of IS designation 4.75 mm |
| 1245 | Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment) |
| 1246 | PREPARATION WORKS |
| 1247 | Fine dressing of the ground |
| 1248 | Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge |
| 1249 | Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately). |
| 1250 | Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts |
| 1251 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) |
| 1252 | Holes 1.2 m diameter and 1.2 m deep |
| 1253 | Holes 90 cm diameter and 90 cm deep |
| 1254 | Holes 60 cm diameter and 60 cm deep |
| 1255 | Holes 45 cm diameter and 45 cm deep |
| 1256 | MAINTAINANCE WORK |
| 1257 | Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. |
| 1258 | TREES |
| 1259 | Delonix regia.Gulmohar / April fool |
| 1260 | Cassia fistula.Amaltash |
| 1261 | Pterospermum acerifolium.Makchund |
| 1262 | Ficus religiosa.peepal |
| 1263 | Ficus benghalensis.bargad / banyan |
| 1264 | Cestrum nocturnum.raat rani |
| 1265 | Azadirachta Indica.Neem |
| 1266 | Bauhinia purpurea.Kachnar |
| 1267 | Callistemon lanceolatus.Bottle brush |
| 1268 | Spathodea campanulata.rugtoora |
| 1269 | Plumeria alba.white champa |
| 1270 | Plumeria rubra.pink champa |
| 1271 | Lagerstroemia flosreginae.jarul |
| 1272 | Polyalthia longifolia.Ashok |
| 1273 | Tectona grandis.sal |
| 1274 | Tamarindus indica.Imli |
| 1275 | Mangifera indica.Mango |
| 1276 | Eugenia jambolana.Jamun |
| 1277 | Phyllanthus emblica.Amla |
| 1278 | foxtail palm |
| 1279 | Bottle palm |
| 1280 | BAMBOO |
| 1281 | Buddha belly bamboo |
| 1282 | SHRUBS |
| 1283 | Clerodendrum inerme.Volkameria inermis |
| 1284 | Ficus panda |
| 1285 | Ficus benjamina Starlight.Ficus Starlight |
| 1286 | Gardenia jasminoides |
| 1287 | Golden duranta |
| 1288 | Hamelia patens |
| 1289 | Hibiscus rosa-sinensis.udhul |
| 1290 | Raphis excelsa.lady palm |
| 1291 | Tecoma gaudichaudi.Yellow bells |
| 1292 | TMC dwarf.Chandani |
| 1293 | Canna dwarf |
| 1294 | GROUND COVERS |
| 1295 | Alternanthera red |
| 1296 | Chlorophytum comosum |
| 1297 | Jatropha |
| 1298 | Sprenger's asparagus.Foxtail fern |
| 1299 | Syngonium podophyllum.Syngonium butterfly |
| 1300 | Tradescantia pallida |
| 1301 | GRASS |
| 1302 | Cynodon dactylon.doob grass |
| 1303 | FURNITURE WORK |
| 1304 | Model: Capital/B, Office DeskSize: 1650Wx600Dx750H mm.Supplying and placing in position of office desk structure of rectangular shape. Primary work surface 18mm thick table top made of prelaminated particle board with metal pedestal work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. under structure made of metal 25x25x1.2mm -MS metal all metallic parts should be epoxy polyester powder coating to thickness of 50-micron (approx.) Both side fixed pedestal size is 350mm(l)x 499mm(d)x 735mm(h), in provided with central lock for security and handles are provided for easy of opening. overall construction of fixed pedestal is made in 0.6mm CRCA along with facia of drawers. Three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1305 | Model: Define, Standard Mesh Chair, Medium BackChair Dimension: 585Wx660Dx1060H mm. Seat depth: 500mm, Back Height: 490mmmedium back 360°-degree revolving chair *The chair made of full mesh in black colour.it will come in matte finish about style type is gf nylon structure with nylon net on back.details:arms: fixed pp armrest.Use of ply: 12 mm thick hot pressed BWR plywood (is grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, Back: frame of design shall be curved made of two pieces injection moulded frame cover with mesh. backrest support adjustable lumbar support. Mechanism: single locking mechanism.Gas lift 100 mm telescopic hydraulic. Base: 650mm nylon base with smooth castorsThe Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1306 | Model: Define, Mesh Chair, Medium BackChair Dimension: 590Wx630Dx970H mm. fix cantilever chair The chair made of full mesh in black colour.it will come in matte finish in contemporary style.details:Arms: pp fixed padded armrest.Use of ply: 12 mm thick hot pressed BWR plywood (is grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, Back: frame of design shall be curved made of two pieces injection moulded frame cover with mesh. backrest support adjustable lumbar support. Fixed cantilever chair. Base: chrome plated tubular frame of cantilever type.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1307 | Model: Lab Table Size: 750Wx520Dx850H mm.Providing & suppling placing position of Lab Table C-Frame Structure in 60 x 30 x 2 mm thk hollow pipe construction.Storage Cabinet of L=750mm W-520mm H-675mm of 1 drawer 2 shutters and 1 shelf having plinth base with leveling stud. godrej or Equivalent lock on drawer (for standing posture) Single sided Half Taperzoid Electrical Duct.Electrical socket of 6/16 amps of North west make Or equivalent & MCB switch (Single phase) without wiring.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1308 | Providing and fixing 2 Tier Reagent Racks of size 750mm(L) x 300mm(W) x 680mm(H):- Reagent Racks shall be complete modular design consisting of 2 stage horizontal storage shelves made of 1.6 mm thick frame. Shelf : Fixed-Type reagent shelves have 1.6mm thickness consisting of 2 stage horizontal storage shelves made of 1.6 mm thick frame of CRCA MS sheet with epoxy powder coating and shall have 4 nos. plates (containing 03 module each) for electrical switches and sockets including necessary wiring etc. It shall have provision for placing Granite pieces. Cutout for 3 module plate to be provided. All the members are knock down and can be restructured. The metal part cutout shall be of 1.00mm thickness. The finish shall be coating of 40-60micron thickness. Load carrying capacity of 70kg for Island table. All the above items shall be as per photo, sketch specifications & direction of engineer-incharge. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1309 | Providing and Placing in position Lab Stools. The seat shall be made up of 1.2±0.1cm thick flat plywood and with moulded Polyurethane foam and are upholstered with replaceable synthetic leather covers. The dimensions of Seat shall be Diameter 40.0 cm and Adjustments are 360° Revolving type. The back foam shall be designed with contoured Lumbar support for extra comfort. The upholstery shall be available in synthetic leather. The dimensions of Back shall be 45.0 cm (W) covered with polyurethane foam. The HR polyurethane Foam shall be moulded with density = 45 +/-2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The manual height adjustment shall be very easy to operate with a help of a knob. It should be easily locked at the most comfortable position. The five-prong pedestal shall be fabricated from 0.2 ± 0.02 cm thick HR sheet ( IS : DD 1079/ HR ), Powder coated ( DFT 40-60 microns ) and shall be fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The pedestal shall be 55.0±0.5cm pitch-circle diameter (65.0±1.0cm with castors). Circular-foot-ring of dia 52.0±0.2cm shall be made up of 01.9±0.2 x 0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool. The twin wheel castors shall be injection moulded in Black Nylon. Overall dimensions shall be Width- 65.0cm, Depth- 65.0 cm, Seat Height- 45.0 to 56.5cm.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1310 | Model: Free Standing Office Table Table Size: 1000Wx600Dx750H mm.Providing & supplying modern design modular cabin a combination of metal and wood make the products utile and a delight. Timeless design that elevates your office space table with smart storage side unit structure of spacious l-shaped tabletop offers you a generous workspace, dual-tone design in frosty white and walnut blends. Desk primary work surface use premium quality materials, which give more surface area for work, table top made of 25mm thick prelaminated particle board of grade ii type iii of is 12823/latest. On table top 6 module flip top box without switch & socket single raceway & pole with powder coated below wiring & table top supported with nontoxic MS powder coated \\"c\\" shape metal legs vertical of size 50mm x 50mm x 1.6 mm and connectors horizontal of size 40mm x 40mm x 1.6 mm mgs pipe. providing 0.8mm thick MS powder coated to the thickness 50-60 microns (+/-5 micron) CRCA sheet perforated modesty panel at front side, below top with work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. All metal parts should finish with epoxy polyester powder coated to the thickness 50-60 microns (+/-5 micron).The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1311 | Low Ht Storage Size: 1650Wx450Dx750H mm.Supplying, and placing in position of back storage as per photograph/drawing . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters withD shape handles & locking arrangement. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1312 | Model:Office DeskSize: 1200Wx600Dx750H mm.Supplying and placing in position of office desk structure of rectangular shape. Primary work surface 25mm thick table top made of prelaminated particle board work surface with the hot melt glue used for fixing the 2mm thick PVC edge banding made of same matte finish, wire management hole with PVC grommet on table top. Right side table top based on a fixed pedestal with 1drawer + 1 filling box shelve is made in 18mm thick engineered wood, in provided with central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with facia of drawers. Three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1313 | Student DeskProviding & supplying fixing of three & two seater college desk with shelf/storage under desk which one made by cast iron, desk top made by 18mm thick prelaminated particle board of grade ii type iii of is 12823/latest, two-seater classroom desk cum bench,under structure-black 9005 ERW pipe (as per is:7138) : 25x25x1.2mm square M.S. pipe, of thickness 1.2mm in black epoxy polyester powder coated to the thickness 50-60 microns(+/-5 micron) at base with plastic caps made of pp copolymer (3530 grade) are also provided on the rear frames adding more aesthetic value to the product. Additional horizontal supports of M.S. c sections of 1.5mm thick are provided below the desk & seat. Shelf: 0.8mm thick powder coated M.S. sheet below the desk & hooks on either side of desk in M.S. rod of Dia 6mm.top, seat, back & modesty panel: 18mm thick pre laminated board with machine pressed exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade fixed duly pasted with the assistance of edge banding machine at 200 degree Celsius.Three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1314 | Three Seater size of bench: 1500mm(l)x 950mm(d)x 760mm(h)desk size: 1500mm (w) x 400mm (d) x 760mm (h)bench size: 1500mm (w) x 310mm (d) x 390 / 760mm (h)back size : 1500mm (w) x 150 mm (h), |
| 1315 | Two Seater Size of bench: 1200mm(l)x 950mm(d)x 760mm(h)Desk size: 1200mm (w) x 400mm (d) x 760mm (h)Bench size: 1200mm (w) x 310mm (d) x 390 / 760mm (h)Back size: 1200mm (w) x 150 mm (h), |
| 1316 | 2-Seater Front Sizes: PointT8-2F: 1200Wx520Dx900H mm. Prelaminated Board modesty panel with laminate finishPrelaminated Board seat & back with laminate finish high quality steel stanchionBack - Prelaminated Board back with laminate finishProvision for Raceway for switch-outs.Auditorium |
| 1317 | 2-Seater Middle Sizes: PointT8-2M: 1200Wx810Dx900H mm. Prelaminated Board modesty panel with laminate finishPrelaminated Board seat & back with laminate finish high quality steel stanchionBack - Prelaminated Board back with laminate finishSeat – Counterweight tip-up mechanism for a lifetime of smooth operationTable – Prelaminated Board 18mm table top in laminate finishProvision for Raceway for switch-outs.Auditorium |
| 1318 | 3-Seater Front Sizes: PointT8-3F: 1800Wx520Dx900H mm. Prelaminated Board modesty panel with laminate finishPrelaminated Board seat & back with laminate finish high quality steel stanchionBack - Prelaminated Board back with laminate finishProvision for Raceway for switch-outs.Auditorium |
| 1319 | 3-Seater Middle Sizes: PointT8-3M: 1800Wx810Dx900H mm. Prelaminated Board modesty panel with laminate finishPrelaminated Board seat & back with laminate finish high quality steel stanchionBack - Prelaminated Board back with laminate finishSeat – Counterweight tip-up mechanism for a lifetime of smooth operationTable – Prelaminated Board 18mm table top in laminate finishProvision for Raceway for switch-outs.Auditorium |
| 1320 | 3-Seater Last Sizes: PointT8-3L: 1800Wx670Dx900H mm.Prelaminated Board modesty panel with laminate finishPrelaminated Board seat & back with laminate finish high quality steel stanchionBack - Prelaminated Board back with laminate finishSeat – Counterweight tip-up mechanism for a lifetime of smooth operationTable – Prelaminated Board 18mm table top in laminate finishProvision for Raceway for switch-outs.Single metal wire raceway & verticle eletcrical pole below table top.Auditorium |
| 1321 | Office DeskOverall Size: 2400Wx2200Lx770H mm.Supplying, and placing in position of table as per photograph. 50mm thick table top made of MDF board with natural veneer work surface with cherry finish veneer same matching veneer edge banding made of same dark cherry P.U. polish. Modesty is designed with leather patch. Side panel made of 40mm thick.* Provision of side unit of size is 900mm(l)x 595mm(d)x 770mm(h), construction of side unit top made of 50mm thick, 1 fixed shelve with 1 sliding shutter.* All the MDF board are is-14587-1998 with confirm to din 68861.iso 9001- 2015 quality certification confirming to ASTM d 4499 standards for viscosity and thermal stability.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1322 | Back StorageSize: 1600Wx400Dx770H mm.providing & suppling placing position of modular back unit top shall be made from 25 mm thick prelaminated particle board/veneer - MDF/steam beech veneer of grade ii type iii of is 12823/latest & confirm to din 68861.iso 9001- 2015. While rest of the sides as well as shelves and shutter to be made up of 18 mm thick prelaminated particle board/veneer - MDF/steam beech veneer P.U. polish. all edges to be provided with same matching veneer edge banding fixed with the hot melt glueStorage unit with 4 shutters construction is 2 openable doors with 1 fixed shelve + 2 openable doors with 1 fixed shelve, in provided with 2 universal cam lock for security and handles are provided for easy of opening. over all height of product is @ 770 mm.Each shutter should be fixed with required numbers hinges, ss tower bolt of 100 x 10, double strip magnetic catcher and drawers shall have 100 mm size ss fancy handles (one on each drawer) with necessary hardware/ fitting/ hinges etc. of approved quality (make: ebco). for installation of side unit wooden dowels and Mini fix to use for additional support.All the MDF board are is-14587-1998 with confirm to din 68861.iso 9001- 2015 quality certification confirming to astm d 4499 standards for viscosity and thermal stability.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1323 | Premium Leatherette Chair, High BackDimension: 640Wx500Dx1210H mm. Seating Height: 540mm, Seat depth: 500mm, Back Height: 655mmhigh back 360°-degree revolving chair *The chair made of full leatherette in black colour.it will come in matte finish in contemporary style.details:Arms: fixed chrome finish arms with PU padding.Use of ply: 12 mm thick hot pressed BWR plywood (is grade - 303 for seat and back).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, Back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back. backrest support foam design based on symmetrical lumbar supportMechanism: centre tilt mechanism.Only seat size is 665mm(l)x 500mm(d)x 580-495mm(h) & the back size is 665mm(l)x 580mm(h),seat maximum height is 635mm & minimum height is 540mm & back height from floor maximum height is 1210mm & minimum height is 1110mmGas lift 85mm telescopic hydraulic.Base: 650 mm shiny chrome base with nylon castors shall be 65.0 +/- 0.5 cm pitch-centre-Dia (75.0 +/- 1.0 cm with castors)The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1324 | Premium Leatherette Chair, Low BackDimension: 625Wx490Dx1135H mm.Seat depth: 490mm, Back Height: 560mmlow back 360°-degree revolving chair *The chair made of full leatherette in black colour.it will come in matte finish in contemporary style.details: Arms: chrome finish arms with PU padding.Use of ply: 12 mm thick hot pressed BWR plywood (is grade - 303 for seat and back).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, Back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back. backrest support foam design based on symmetrical lumbar support* Mechanism: centre tilt mechanism.Only seat size is 625mm(l)x 490mm(d)x 660-535mm(h) & the back size is 625mm(l)x 560mm(h)seat maximum height is 660mm & minimum height is 535mm & back height from floor maximum height is 1135mm & minimum height is 1035mmGas lift 95mm telescopic hydraulic. Base: 650 mm shiny chrome base with nylon castors shall be 65.0 +/- 0.5 cm pitch-centre-Dia (75.0 +/- 1.0 cm with castors)The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1325 | Leatherette SofaDesigned with generously cushioned backrests and padded arms, Nadia is one of our most comfortable seating collections. A curvaceous silhouette with inlaid wooden accents lends it an enduring style you’ll love season after season. Wrapped in anti-peel, family-friendly leatherette, Nadia makes your everyday worry-free for years to come.Material & Subtype: Engineered Wood - MDF,Premium LeatheretteFrame Material: Plywood,Solid WoodUpholstery Material: Premium Leatherette, Filling Material: Loose Fiber,FoamSeat Material: Premium LeatheretteLeg Material: PVCFinish: GlossyThe Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1326 | Leatherette 3 Seater Sofa Size: 1800Wx930Dx860H mm. |
| 1327 | Leatherette 1 Seater Sofa Size: 860Wx930Dx860H mm. |
| 1328 | Solid Wood Coffee Table in Walnut FinishSize: 1200Wx600Dx480H mm.The Hertz coffee table infuses your living space with a warm, modern aesthetic with its brick-patterned solid wood tabletop. While the inverted angelled legs celebrate the Scandinavian craftsmanship.Material & Subtype: Solid Wood - Beech WoodTable Top Material: Solid WoodFrame Material: Solid WoodLeg Material: Solid WoodFinish: GlossyColour & Colour Family: Brown - WalnutTable Top Thickness: 36mmThe Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1329 | Solid Wood Side TableSize: 600Wx500Dx465H mm.The Carlos collection stuns with its harmonious geometrical shapes and invite the eyes to explore the inherent beauty of solid wood. While the exotic Ash Burl veneer tabletop tells a story of refined craftsmanship with its stunning brick patterns.Material & Subtype: Solid Wood - Steam Beech Wood,VeneerTable Top Material: VeneerLeg Material: Solid WoodFinish: MatteColour & Colour Family: Brown - WalnutTable Top Thickness: 35mmThe Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1330 | Table Size: 1500Wx600Dx750H mm. & Side Unit Size: 900Wx450Dx750H mm.Providing & supplying modern design modular cabin a combination of metal and wood make the products utile and a delight. Timeless design that elevates your office space table with smart storage side unit structure of spacious l-shaped tabletop offers you a generous workspace, dual-tone design in frosty white and walnut blends. Desk primary work surface use premium quality materials, which give more surface area for work, table top made of 25mm thick prelaminated particle board of grade ii type iii of is 12823/latest. On table top 6 module flip top box without switch & socket single raceway & pole with powder coated below wiring & table top supported with nontoxic MS powder coated \\"c\\" shape metal legs vertical of size 50mm x 50mm x 1.6 mm and connectors horizontal of size 40mm x 40mm x 1.6 mm mgs pipe. providing 0.8mm thick MS powder coated to the thickness 50-60 microns (+/-5 micron) CRCA sheet perforated modesty panel at front side, below top with work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. All metal parts should finish with epoxy polyester powder coated to the thickness 50-60 microns (+/-5 micron).Side unit: 900 mm(l)x 450 mm(d)x 750 mm(h),25 mm thick side unit top made of prelaminated particle board, below side unit 1 fixed pedestal size: 400 mm(l)x 450 mm(d)x 725 mm(h) (2 drawers + 1 filling unit) in provided with central lock for security and MS. press handles are provided for easy of opening. Easy to maintain / warp and scratch resistant / borer and termite resistant. Three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1331 | Premium Mesh Chair, High BackChair Dimension: 640Wx670Dx1350H mm. Seating Height: 540mm, Seat depth: 500mm, Back Height: 815mmhigh back 360°-degree revolving chair the chair made of full mesh in black colour.it will come in matte finish about style type is modern.details:Arms: armrest is having two adjustment heights (up & down).Use of ply: 12 mm thick hot pressed BWR plywood (is grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, Back: frame of design shall be curved made of two pieces injection moulded frame cover with mesh. backrest support adjustable lumbar supportMechanism: self-weighted multi locking mechanism.Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 815mm(h),seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1350mm & minimum height is 1250mm Gas lift 100 mm telescopic hydraulic Base: 650 mm chrome prong base is 620mm pitch centre Dia (660mm with castors).The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1332 | , Mesh Chair, Medium BackChair Dimension: 605Wx575Dx1010H mm. Seating Height: 470mm, Seat depth: 500mm, Back Height: 550mmFix cantilever chair *The chair made of full mesh in black colour.it will come in matte finish in contemporary style.details:Arms: pp fixed padded armrest.Use of ply: 12 mm thick hot pressed BWR plywood (is grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, Back: frame of design shall be curved made of two pieces injection moulded frame cover with mesh. backrest support adjustable lumbar support. Only seat size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is 465mm(l)x 550mm(h), seat max height is @ 470mm.Fixed cantilever chair. Base: MS powder coated tubular frame of cantilever type.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1333 | Leatherette 2 Seater SofaSize: 1410Wx890Dx870H mm.A modern curvaceous silhouette with flared arms and round legs. Wrapped in the comfort of premium leatherette, Berry has been a forever favourite.Material & Subtype: Premium LeatheretteFrame Material: Solid WoodUpholstery Material: Premium LeatheretteFilling Material: FoamSeat Material: Premium LeatheretteLeg Material: PVCFinish: Matte The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1334 | Model: Workstations With Pedestal UnitSupplying and placing in position of sliding tile base modular Workstation of 1200mm(H) as per photograph/drawing. Free standing partition height 1200mm and should be minimum of 65-67mm thick. Partition inner frame is 1.1-1.2 mm thick mild steel. Horizontal and vertical trims are made out of extruded aluminum of 1.mm thick. All Panels/trims shall be powder coated with 50 microns. Aluminum trims are elegantly fixed with special fixtures in the partition. The frame work shall be fitted with 9mm thick pre laminated Particle tiles of approved shade. Partition shall have provision for pin up board with fabric/ white marker/ laminated of approved shade. Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels; one at skirting and another above / below the table top. The complete partitioning work shall be carried out as per the approved drawing. Tabletop for workstation made up of 25mm thick pre laminated Particle board of approved shade. The worktop shall be supported on minimum 2mm thick powder coated CRCA brackets and side panels. Side’s panels should be made from 18mm thick pre laminated Particle board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature Provision of one PVC keyboard tray and Metal CPU trolley with lockable castors for each seating.The complete partitioning work shall be carried out as per the approved drawing. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1335 | 4Seater Size: 2400Wx1200Dx750/1200H mm. Back to Back With Pedestal of size: 400Wx450Dx725H mm. |
| 1336 | 2Seater Size: 2400Wx600Dx750/1200H mm.With Pedestal of size: 400Wx450Dx725H mm. |
| 1337 | 1Seater Size: 1500Wx1500Lx600Dx750/1200H mm.With Pedestal Size: 400Wx450Dx725H mm. |
| 1338 | Low Ht Storage Size: 1200Wx450Dx750H mm.Supplying, and placing in position of back storage as per photograph/drawing . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters withD shape handles & locking arrangement. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, , FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1339 | Reception Desk With PedestalSize: 2400Wx900Dx750/1100H With Glass mm.Supplying and placing in position of reception table made of 25mm thick table top of prelaminated particle board in sapeli colour. Above table 18 mm thick counter top with glass height from table top @ 350mm,10 mm thick clear glass diamond cut finish on edges based on stainless steel stud grade 304. one mobile pedestal (2 drawers + 1 filing cabinet) size is 400 mm(l)x 450 mm(d)x 600 mm(h).The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1340 | Three Seater Size: 1650Wx750Dx710H mm.supplying and placing exclusive premium leatherette modernist classic design lounge seating sofa with kiln-dried wood framing makes it warp and scratch resistant, comfortable seat depth & height designed keeping modern Indian lifestyle in mind, wrapped in buttery-soft premium leatherette, the panelled back and cushioned armrests encourage lounging, designed with modernity & elegance, choose the option that suits your home. Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 Indian standard for commercial (common) and moisture proof plywood (tentative).under structure frame shall be constructed from 18 mm thick kiln-dried German beech wood framing is highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue ,the frame shall be padded with high resilience polyurethane foam having 25 +/- 5 density in seat it shall be stack foam of 40mm thik,40mm thick back foam having 25 +/- 5 density foam used ,there shall be cushion arm 40mm thick provided padded with high resilience polyurethane foam having density 25 +/- 5. the complete stack foam structure shall be covered with premium leatherette in brown-camel brown colour, it complements the modish sleek steel. ( seat : 545 mm(d) x 410mm(h) , arms height @ 610 mm / back height @ 290 mm).The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1341 | Size: 1200Wx600Dx485H mm.Coffee Table in Two Tone FinishThe Holston coffee table effortlessly combines contemporary functionality with minimalistic style. Its frosty white open shelves, set against the Lyon walnut frame, create a captivating interplay of colours. Boasting generous storage space, the Holston table adds an organized charm to your modern living space.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1342 | Model: Workstations With Pedestal UnitSupplying and placing in position of sliding tile base modular Workstation of 1200mm(H) as per photograph/drawing. Free standing partition height 1200mm and should be minimum of 65-67mm thick. Partition inner frame is 1.1-1.2 mm thick mild steel. Horizontal and vertical trims are made out of extruded aluminum of 1.mm thick. All Panels/trims shall be powder coated with 50 microns. Aluminum trims are elegantly fixed with special fixtures in the partition. The frame work shall be fitted with 9mm thick pre laminated Particle tiles of approved shade. Partition shall have provision for pin up board with fabric/ white marker/ laminated of approved shade. Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels; one at skirting and another above / below the table top. The complete partitioning work shall be carried out as per the approved drawing. Tabletop for workstation made up of 25mm thick pre laminated Particle board of approved shade. The worktop shall be supported on minimum 2mm thick powder coated CRCA brackets and side panels. Side’s panels should be made from 18mm thick pre laminated Particle board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature Provision of one PVC keyboard tray and Metal CPU trolley with lockable castors for each seating. The complete partitioning work shall be carried out as per the approved drawing. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1343 | Model: 3 Seater Size: 3600Wx600Dx750/1200H mm. With Pedestal of size: 400Wx450Dx725H mm. |
| 1344 | Model: Smart Library TableSize: 1800Wx900Dx750H mm.providing & supplying modern design library table, tabletop offers you a generous workspace, desk primary work surface use premium quality materials.Top made of 25mm thick which give more surface area for work ,table top made of prelaminated particle board of grade ii type iii of is 12823/latest, tabletop supported with nontoxic Ms powder coated smart series slant legs made in Ms is:304 grade of leg size 50mm x 50mm under structure and horizontal connectors,0.12 mm thick.Our work surface furniture is finished with exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade, fixed with hot melt glue.Three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest,The Seller / Company should be ISO9001:2008, ISO 9001:2015, ISO 14001:2015, OHSAS 18001:2007, SEFA, Green pro, Indian Design Mark, AIOTA, FSC & SEDEX Certified. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and an official product official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1345 | Full Ht Storage Size: 900Wx450Dx2100H mm.Supplying, and placing in position of back storage as per photograph/drawing . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters withD shape handles & locking arrangement. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1346 | Model: Workstations With Pedestal UnitSupplying and placing in position of sliding tile base modular Workstation of 1200mm(H) as per photograph/drawing. Free standing partition height 1200mm and should be minimum of 65-67mm thick. Partition inner frame is 1.1-1.2 mm thick mild steel. Horizontal and vertical trims are made out of extruded aluminum of 1.mm thick. All Panels/trims shall be powder coated with 50 microns. Aluminum trims are elegantly fixed with special fixtures in the partition. The frame work shall be fitted with 9mm thick pre laminated Particle tiles of approved shade. Partition shall have provision for pin up board with fabric/ white marker/ laminated of approved shade. Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels; one at skirting and another above / below the table top. The complete partitioning work shall be carried out as per the approved drawing. Tabletop for workstation made up of 25mm thick pre laminated Particle board of approved shade. The worktop shall be supported on minimum 2mm thick powder coated CRCA brackets and side panels. Side’s panels should be made from 18mm thick pre laminated Particle board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature Provision of one PVC keyboard tray and Metal CPU trolley with lockable castors for each seating. The complete partitioning work shall be carried out as per the approved drawing. The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and an official link/screenshot of the product listing must be provided from www.bifma.org” |
| 1347 | , 2Seater Size: 1500Wx3000Lx600Dx750/1200H mm.With Pedestal Size: 400Wx450Dx725H mm. |
| 1348 | , 4Seater Size: 3000Wx3000Lx600Dx750/1200H mm.With Pedestal Size: 400Wx450Dx725H mm. |
| 1349 | Office DeskSize: 1200Wx600Dx750H mm.Supplying and placing in position of office desk office desk structure of rectangular shape. Primary work surface 25mm thick table top made of 25mm thick prelaminated particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. modesty panel made of 18mm thick, wire management hole with PVC grommet on table top. Construction right side of table top is based on a fixed pedestal 3 drawers & from left side of table top is based on 18mm thick engineered wood PVC edge banding pedestal back, top, bottom & drawers are made of 18mm thick with 1 CPU trolly made in black metal powder coated. Fixed pedestal: l:410mm(l)x 580mm(d)x 750mm(h), in provided with central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with facia of drawers. Three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” Please Enable Macros to View BoQ information |
| 1350 | Office DeskSize: 1200Wx600Dx750H mm.Supplying and placing in position of office desk office desk structure of rectangular shape. Primary work surface 25mm thick table top made of 25mm thick prelaminated particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue. modesty panel made of 18mm thick, wire management hole with PVC grommet on table top. Construction right side of table top is based on a fixed pedestal 3 drawers & from left side of table top is based on 18mm thick engineered wood PVC edge banding pedestal back, top, bottom & drawers are made of 18mm thick with 1 CPU trolly made in black metal powder coated. Fixed pedestal: l:410mm(l)x 580mm(d)x 750mm(h), in provided with central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with facia of drawers. Three layer prelaminated particles board (wood product) of grade ii type iii of is 12823/latest.The Seller / Company should be NABCB CERTIFIED ISO-9001:2008, ISO-9001:2015, ISO-14001:2015, OHSAS-18001:2007. OTHER CERTIFICATIONS : Green pro, Indian Design Mark, AIOTA, FSC & SEDEX. The Bidder should also be a member of BIFMA and One or more products of the OEM should be certified as BIFMA compliant and BIFMA level an official link/screenshot of the product listing must be provided from www.bifma.org” Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysSep 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender