Tender For S:-Provn Of Auditorium For Stn Units Less Cat A (Cmm And 1Stc With 600 Seating Capacity At Jabalpur Mil Stn (Under Ground Sumps)
Tender Value
11.10 Lakhs
Estimated cost
Bid Submission
17 Sep 2026
17 days left
EMD
22200
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for S:-Provn Of Auditorium For Stn Units Less Cat A (Cmm And 1Stc With 600 Seating Capacity At Jabalpur Mil Stn (Under Ground Sumps)
BOQ
| Sl. No. | Item Description |
| 1 | Surfaces excavation n exc 30 cm deep and averaging 15cm deep and getting out in hard and dense soil complete all as specified and directed. |
| 2 | Excavation over areas, not exceeding 1.50 m deep and getting out in hard/dense soil complete all as specified and directed. |
| 3 | Excavation over area, exceeding 1.50 m but not exceeding 3.00 m deep and getting out in hard/dense soil complete all as specified and directed. |
| 4 | Excavation in trenches not exc 1.5 mtr wide and not exceeding 1.5mtr depth for foundation in soft/loose soil & getting out. |
| 5 | Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 6 | M&L for hard core, broken stone / boulders to gauge n exc 63 mm laying in layers complete all as specified and directed. |
| 7 | M&L for PCC (1:4:8) type D2 using 40mm graded aggegate as in foundation complete all as specified and directed. |
| 8 | Returning filling in incl spreading, levelling, watering & well ramming in layers not exc 25cm thick for soft/loose soil complete all as specified and directed. |
| 9 | Removing excavated material 250 m but n.exc 50m and depositing where directed at a lavel .exc 1.50 mtr above the starting point complete all as specified and directed. |
| 10 | M&L RCC design mix M-30 (using 20mm graded stone aggregates) in slabs supported on walls, beams & columns complete (reinforcement to be measured separately). |
| 11 | M&L RCC design mix M-30 (using 20mm graded stone aggregates) in wall, pillars, posts & struts complete (reinforcement to be measured separately) complete all as specified and directed. |
| 12 | M&L RCC design mix M-30 (using 20mm graded stone aggregates) in foundations, footing, plinth beams, bases for columns and mass concrete complete (reinforcement to be measured separately) complete all as specified and directed. |
| 13 | M&L 50 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in flooring finished the surfaces even & fair without using extra cement complete all as specified and directed. |
| 14 | M&L for RCC design mix M-25 using 20mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 15 | M&L for RCC design mix M-25 using 20mm graded stone aggregate in Beams, cantilevers, bressummers, over 1.5m span complete all as specified and directed. |
| 16 | M&L for RCC design mix M-25 using 20mm graded stone aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 17 | M&L for RCC design mix M-25 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 18 | Form work to curved wall, for rough finished flat surfaces of concrete complete and al as specified and directed. |
| 19 | M&L for Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. |
| 20 | M&L for use and waste of formwork flat surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed. |
| 21 | M&L for Use and waste of formwork rough finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed. |
| 22 | M&L for Use and waste of formwork rough finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 23 | Mild steel TMT bars 10mm dia & over cut to length, bent to shape required incl cranking bending with0.9 mm dia MS wire (annealed) not less than0.9 mm dia or securing with clips complete all as specified and directed. |
| 24 | Ditto all as per item No 23 but 5mm dia and over upto and incl 10 mm dia in stirrups, spacers and binders. |
| 25 | Ditto all as per item No 23 but 6 to 8mm dia complete all as specified and directed. |
| 26 | M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 27 | M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed. |
| 28 | M&L 15mm thick cement plastering in CM 1:6 complete all as specified finished even & smooth without using extra cement complete all as specified and as directed.. |
| 29 | M&L Rendering 15mm thick in Cement Mortar 1:4 on Fair Faces of Brick Walls or on Concrete Surfaces plastered Surfaces Finished fair and even complete all as specified and directed. |
| 30 | M&L rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete all as specified and directed. |
| 31 | Supply only integral WPC complete all as specified and as directed. |
| 32 | M&L Providing precast cement concrete louvers and jallies 35 mm thick type C0 1:3:6 set in cement mortar 1:4 complete and all as specified and directed. |
| 33 | S&F CI man hole cover medium duty complete all as specified and as directed. |
| 34 | M& L for Mild steel conforming to Fe 410-0 or Fe 310-0 in fiamed work such as grils, gratings etc with ends of bars shouldered and /or riveted or forged into spikes; framed guard bars; ladders; Gate; railings and similar work complete and all as specified and directed. |
| 35 | M & L for Galvanised with grade of zine coating 275, plain steel sheeting 0.63 mm thick with two corrugation side lap, fixed with, in roofs, walls etc complete all as specified and directed. |
| 36 | 100 mm th PCC 1:4:8 type D2 ( Using 40 mm graded stone agg.)as in sub base of floors complete all as specified and as directed. |
| 37 | M&L 100 mm thick with cement concrete 1:2:4 type B2 (40mm graded aggregate), in floor all around tank(Plinth) and in floors etc finished even & smooth without using extra cement complete all as specified and as directed. |
| 38 | Supply and fix machine pressed precast concrete interlocking paver block any shape and size with gray cement & pigment confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and as directed. |
| 39 | M&L for sand filling under floors complete all as specified & directed. |
| 40 | M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed. |
| 41 | M&L for PCC 1:2:4, type B-1 using 20 mm graded stone aggregate as in coping, benching, bed block, lintel band, plinth courses etc and similar work including necessary form work complete all as specified and directed. |
| 42 | M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed. |
| 43 | S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 44 | S&F for butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed. |
| 45 | S&F for extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed. |
| 46 | S&F for aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300mm and fixed complete all as specified and directed. |
| 47 | S&F for aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed. |
| 48 | 75 mm thick plain cement concrete 1:3:6 mix, type C-2 using 40mm graded stone aggregate as in plinth portection, finishing the surfaces even and smooth without using extra cement complete all as specified and directed . |
| 49 | Preparation of new plastering surfaces of walls and applying two coats of cement base paint complete all as specified. |
| 50 | Prepration of newly plastered surfaces and applying three coat of white wash on ceiling complete all as specified and as directed. |
| 51 | M&L for providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for Non approachable roofs-(i) Cleaning and sweeping and washing down with water to remove all dust etc from plastered roof surfaces / walls and filling of crack with sealing compound etc (ii) Bituminous based primer conforming to IS: 3384 – 1965 @ 0.3 Kg/Sqm (iii) One layer of super thermo APP modified water proofing memberane with non polyester reinforcement of any make.( M/s STP texsa ltd/Hyperplas memberane of M/S IWL India ltd/MS STPand Tikki Tar ltd). (iv) 3mm thick and minimum Weight @3.50Kg/Sqm,laid with gas torch and pasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surface after cutting necessary grooves and making good with PCC gola 1:2:4 type- B1 etc adhere to bitumen all as per manufactures instructions. (v) Applying one coat of aluminum paint @ 0.20 Kg / Sqm in two coats over bitumen layer as per manufacturer instruction . (application including sides lap,over laps shall be provided not less than 10 cm and joint sealed with torch as per manufactureerr's instructions specifications and as per particular specifications complete all as specified and directed. |
| 52 | M&L for 10mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound @ 3% by wight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and direcated (WPC shall be measured & paid seperately) |
| 53 | S&F fancy type draphery rods with two way wooden/brass brackets 20-25mm bore cut to length as reqd of colour as selected , approved by GE & as directed by Engr-in -Charge. |
| 54 | Mild steel framed work for door chowkhats framing for cladding, glazing and like; (made out of angle iron of size 40X40X 6mm); cut to shape including bending and welding as necessary with complete accessories required for fixing chowkhat as well as for hard ware fittings, complete all as specified and directed.Note: All connected MS works shall be measured under this item except butt hinges which shall be measured and paid for separately as supply only. |
| 55 | 35 mm thick, 2nd class hard wood plain framed paneled, Factory made shutter (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply. The size of rail and stiles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated all as specified. |
| 56 | 35mm thick glazed and Skelton shutters, of 2nd class hard wood factory made, open rebated and prepared to receive glass, guage etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass etc. (size of members of shutters as specified in SSR Part-I, Section 8, Clause 8.20 (a) complete all as specified and directed. |
| 57 | PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in hold fast complete all as specified and directed . |
| 58 | M&L for prepartion Surfaces of new wood or wood based materials of any description not other described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed |
| 59 | M&L for preparing new plastered or un-plastered surfaces of walls and applying two coats of oil bound distemper with 2mm thick wall care putty over a coat of chalk whitining on walls complete all as specified and directed. |
| 60 | Supply and fixing for aluminium alloy powder-coate) window frame with shutters open able type, with aluminium sections as per of “Jindal” section numbers for casement windows including aluminium alloy snap type beads, handles, aluminium barrel tower bolts and glazing clip, joint cleats, rubber gaskets etc., complete all as specified for series-B “ Jindal” section numbers for casement (a) Section for shutter 47.62x44.45x1.87 mm thick (b) Glazing clip weighing 0.259kg/mtr. (c) Windows shall be provided with 02 Nos. of tower bolt of size 125mm for single leaf shutter and 03 Nos. for double leaf. Handles shall be aluminium ‘D’ type handle of size 98mm and thickness 2.37mm weighing 0.875kg/mtr and 01 No on each openable leaf shall be provided. (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. 2.Glass pane and wire gauge shall be measured and paid for separately. |
| 61 | Supply and fix 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each complete all as specified. |
| 62 | M & L preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 63 | S & F Door spring ordinary rat tail rod pattern springs including roller and roller plate complete of mild steel 150mm long complete all as specified and as directed. |
| 64 | S&F Floor door stopper 140 mm of aluminium alloy body and tongue anodised with hard steel spring ,fixed in floor complete all as specified and as directed. |
| 65 | M & L, aluminium grills(Decogrill) and fixed including necessary glazing clips, anodized aluminiunm snap beading screws and aluminium fittings complete all as specified and directed. |
| 66 | Supply and fixing and testing of ISI marked MS pipes 100mm dia class 'B' and specials etc as per IS 1239 for under ground/laying or fixing on walls / roofs with supports for hydrant system including transportation provision of specials like bends tees reducers flanges etc welded in proper position incl thrust blocks in PCC 1:2:4 on all bends tees and junctions etc as required wrapping and coating with Pys coat (min 4 mm thick conforming to IS 15337-2003 etc) providing tapping for pressure gauge and other instruments making holes/chasing in walls masonary, RCC slab if required testing, flushing & cleaning of pipe line by water & making good the same as originala all as specified and directed. |
| 67 | Supply fixing testing & commissioning of Butterfly valve ISI marked 100 mm dia of class PN 1.0 including a set of MS flanges complete all as specified and as directed. |
| 68 | Supply & fixing in position ISI marked cast irion double flanged Non Return valve 100 mm dia as per IS 5312 part I including transporting to worksite, supply & fixing nuts, bolts gaskets, flanges & washers etc complete with desting as per directions of the Eingneer-in-charge (MAKE Kirloskar / Kartar / Venus / IVC / Zalotc / Kalpana) |
| 69 | Supply & laying Flat Three Core PVC Insulated & PVC Sheathed Industrial Copper Cable for Submersible Pump Motors 10 Sqmm 3 core complete all as specified and directed. (Make : Finolex/Havells/RR Cable) |
| 70 | Supply & laying Flat Three Core PVC Insulated & PVC Sheathed Industrial Copper Cable for Submersible Pump Motors 6 Sqmm 3 core complete all as specified and directed. (Make : Finolex/Havells/RR Cable) Please Enable Macros to View BoQ information |
| 71 | Supply & laying Flat Three Core PVC Insulated & PVC Sheathed Industrial Copper Cable for Submersible Pump Motors 6 Sqmm 3 core complete all as specified and directed. (Make : Finolex/Havells/RR Cable) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysSep 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender