Tender For Construction Of Cafe House At Silk Weaving Factory Raj Bagh.
Tender Value
38.49 Lakhs
Estimated cost
Bid Submission
16 Sep 2026
18 days left
EMD
76980
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of Cafe House At Silk Weaving Factory Raj Bagh.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : |
| 2 | Supplying /filling dry stone soling tightly hand packed under foundation & under floors including all leads, lifts and all carriages up to site of work complete |
| 3 | P/L of cement concrete 1:4:8 mix using 40mm N/size Agg. In foundation /plinth excluding cost of shuttering complete including carriages. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-all work upto plinth level in 1:2:4 mix using 20mm N/size using crushed aggregate including all carriages upto site of work complete |
| 5 | Centering and shuttering including strutting ,propping etc. and removal of form work for: foundation, footing ,bases for columns |
| 6 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. 40 mm thick with 20mm nominal size stone aggregate |
| 7 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm |
| 8 | Supplying and filling in plinth with fine sand/GSB/nallahmukh under floors including, watering, ramming, consolidating and dressing and inclusive of all carriages upto site of work complete |
| 9 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation, plinth and in superstructure upto floor V level including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) including all carriages |
| 10 | 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand) |
| 11 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including grouting in white cement mixed with pigment of matching shade complete. |
| 12 | Providing and laying in position Reinforced cement concrete of specified grade excluding the cost of centring and shuttering-all work upto plinth level above plinth level in 1:2:4 mix using 20mm N/size using crushed aggregate including all carriages upto site of work complete |
| 13 | P/L of reinforcement for R.C.C. work incl. cutting, binding and placing in position including cost of binding wire. |
| 14 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick |
| 15 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinable cement prime |
| 16 | Finishing wall with acrylic smooth paint exterior of required shde applied @1.67 lt/10sqm over ne work (two or more coats) over and including priming coat of exterior primer applied @ 2.20kg/10sqm complete |
| 17 | P/F OF Doors& Windows made of aluminium doors of different size shall be provided with each shelter as per drawing & Windows aluminium anodized of extrusions powder colour coated aluminium section three tracks with three sliding shutter as approved and directed by the Eng in charges at site complete job. |
| 18 | P/F of 12mm thick framed toughened glass approved brand & manufacture incl.p/f pnot & lopping type arrangement & necessary holes etc for fixing of fitting etc all complete |
| 19 | P/F Track deck crill make or equivalent H.I rib profiled sheets 1000 to 1020mm cover width 28-35 mm high crests at 250 to 255mm T.C.T (total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 No stiffing ribs, effective water shedding and special male/ female ends with full return legs on side Lapps for purlins support and anti capillary flute inside lapp. The sheets shall have a hot dip metallic coated of Zinc and aluminum (150gms/sm) zinc/ aluminum coated mass total on both sides AZ-150 as IS-1397, 550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over micron polyester back coat over 5 micron primer coats on both surfaces including side and end lapp and using 8mm Galvalume hex self drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end lapps etc (measured for unit of laid area) |
| 20 | Providing valley/Ridges colour coated of width 60 cm overall width plain G.S sheet fixed with polymer coated J. or L hooks, bolts and nuts 8mm Dia G.I limpet and bitumen washers complete |
| 21 | P/F Of steel built up section including cutting welding of columns purlins, rafter trusses & hoisting in position including coat of red oxide work all complete job |
| 22 | P/F OF SANITARY ITEMS A) Providing and fixing wash basin with 32 mm waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 630x450 mm with a pair |
| 23 | B) Providing and fixing single piece water closet squatting pan (european type W.C. pan) with 100 mm P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) |
| 24 | C) Providing and fixing health faucet nominal bore C.P. bib cock of approved quality |
| 25 | D) Providing and fixing 15 mm nominal bore of standard back type C.P. close hole basin mixer pillar tap of approved quality |
| 26 | E) Providing and fixing CP Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. |
| 27 | F) Providing and fixing of shower |
| 28 | G) Providing and fixing of 50ltr gryser of approved quality |
| 29 | H) Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points |
| 30 | I) PVC PIPE PRINCE MAKE OF DIA 4” |
| 31 | J) PVC PIPE PRINCE MAKE OF DIA 3” |
| 32 | K) G.I. PIPE OF DIA 1.5” PRINCE MAKE |
| 33 | L) G.I. PIPE OF DIA 1.5” PRINCE MAKE |
| 34 | M) P-TRAP 3” |
| 35 | N) P-TRAP 4” |
| 36 | O) ELBOW 3” |
| 37 | P) COLLAR 3” |
| 38 | Q) TEE 3” |
| 39 | R) TEE 4” |
| 40 | S) WASTE PIPE |
| 41 | T) C.P. CONNECTION 18” TO 24” |
| 42 | U) GRATING |
| 43 | V) TOWEL RING |
| 44 | W) TOWEL ROD |
| 45 | X) PVC WATER STORAGE TANK with all necessary fitting complete job |
| 46 | Wiring for the following light points with 1.5Sqmm PVC insulated copper conductor 1100 volts grade standard flexible FRLS wires of approved make in concealed or surface mounted PVC conduit including providing and fixing of 6 Amp single pole rocker operated flush mounted switch of approved quality, color make and design in 1.6mm thick GI box and earthing of fixtures and the outlet box with 1.5sqmm PVC insulated copper conductor stranded flexible FRLS wire.a). One light controlled by 6 Amp Switch |
| 47 | Wiring for 250 volts single phase and neutral 16 Amps switched socket outlet with 4 Sq.mm PVC insulated copper conductor 1100 volts grade stranded flexible FRLS wires in concealed or Surface mounted 25mm dia 2mm thick PVC conduit including providing and fixing of 16 Amps 3 pin switched socket of approved make and design in 1.6mm thick G1 boxes with grid plates and earthing the third pin of socket outlet with 4 Sq.mm PVC insulated copper conductor stranded flexible FRLS wire. |
| 48 | Supplying installation testing and commissioning of 12 watt slim round LED light of Vipro make complete fitting as required. |
| 49 | Supplying and installation testing and commissioning of following mccb,sa)10 to 32 amp mcbSp |
| 50 | B)40 to 63 amp DP |
| 51 | Supplying and installation testing and commissioning of 6 way TPN DB box |
| 52 | Wiring for 230v ac, 5pin 5/6 amps switched socket outlets for light duty power with 230v ac 5/6amps, SP switch and socket, on same modular grid plate mounting with 2x2.5sqmm stranded copper conductor FRLS insulated 1100v grade wire in 25mm dia, 1.6mm thick rigid MS conduit/Pvc with earthing of 3rd pin by 1/1.5 sq mm stranded copper conductor FRLS insulated green 1100v grade wire with lug complete. |
| 53 | Wiring for ceiling/wall Fan points same as above in item No 1. but controlled by electronic stepped regulator 200 watts and 5A control switch and 15mm dia circular or hexagonal in 1.6mm thick MS zinc passivity sheet steel body and 12mm dia MS bar hook complete with white ,3mm thick 200mm dia laminated circular cover |
| 54 | Supplying installation testing and commissioning of exhaust fan complete connection as required |
| 55 | Supplying installation testing and commissioning of celling fan Crompton Usha or equalent make. |
| 56 | Wiring for circuit wiring 2x2.5 + 1x2.5 |
| 57 | Supplying laying of 1100 volt XLPE insulated aluminium conductor armed cable. 3 core 10sqmm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysSep 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender