Tender For Construction Of District Bio Control Laboratory At Rymphum, Jowai, West Jaintia Hills District, Meghalaya
Tender Value
2.17 Crore
Estimated cost
Bid Submission
29 Sep 2026
16 days left
EMD
4.35 Lakhs
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Khasi Hills → Meghalaya
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of District Bio Control Laboratory At Rymphum, Jowai, West Jaintia Hills District, Meghalaya
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 27-Aug-2026 | EMD Corrigendum | Fee | 29-Sep-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork in excavation by Mechanical means up to a depth of 2m below the existing ground level for foundation, trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification Of soils.All kind of soil (ordinary soil/ hard soil/ dense soil). |
| 2 | Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. Stone soling. 100mm |
| 3 | Plain cement concrete works in foundation bed for footing steps, walls, brick works etc below plinth level as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). 1 :3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size). |
| 4 | Supplying, fitting and fixing in position reinforcement bars up to 1st floor level, conforming to relevant I.S Code for RCC work R.B walling including straightening, cleaning, cutting and bending to proper shapes and length as per detailss, supplying and binding with 20G annealed black wire and palcing in position with proper blocks, support, chairs, spacers etc complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc and no measurement for the same is required). High Yield Strength Deformed bars or Tor Bars. |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form of all heights complete and as directed by Engineer in charge.Foundations, footings, bases of columns, etc for mass concrete (using steel). |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form of all heights complete and as directed by Engineer in charge. Columns, Pillars, Piers, Abutments, Posts and struts (using steel). |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form of all heights complete and as directed by Engineer in charge.Lintels, beams, plinth beams, girders, bressumers and cantilevers (using steel). |
| 8 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping Of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per ls: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineerin-charge. All works up to plinth level. |
| 9 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with: Cement mortar 1 :6 (1 cement: 6 coarse sand). |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for all heights complete and as directed by Engineer in charge.Slabs, roofs, landings, balconies and access platform, shelves (using steel). |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form of all heights complete and as directed by Engineer in charge.Stairs/ spirals staircase, (excluding landings) (using timber). |
| 12 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping Of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per ls: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineerin-charge. All works above plinth level upto first floor level. |
| 13 | Supplying, fitting and fixing in position reinforcement bars up to 1st floor level, conforming to relevant I.S Code for RCC work R.B walling including straightening, cleaning, cutting and bending toproper shapes and length as per detail, supplying and binding with 20G annealed black wire and placing in position with proper blocks, support, chairs, spacers etc complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc and no measurement for the same is required). High Yield Strength Deformed bars or Tor Bars. |
| 14 | (b) Extra over item No. 6.11 (a,b,c) above each subsequent floor or part thereof above the first floor level. |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for all heights complete and as directed by Engineer in charge.Walls (any thickness) including attached pilasters, buttresses plinth and string courses etc (using steel). |
| 16 | Brick work in cement mortar with first class brick in super structure above plinth up to first floor level in all shapes and sizes: Cement mortar 1:4(1 cement : 4 coarse sand) |
| 17 | 20 mm cement plaster of mix: 1 :4 (1 cement: 4 coarse sand). |
| 18 | Cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster. |
| 19 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with:. Makrana white second quality. |
| 20 | Providing and laying Polished Granite stone flooring in required in design and patern, in linear as well as curvilinear portion of the building all complete as per architechural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand ) laid and jointed with white cement slurry and with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-charge. |
| 21 | Providing and fixing 10mm thick acid and /or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mottar bedding, and joints filled with acid and/or alkali resisting cement as per Is: 4457, complete as per the direction of Engineer-in-charge. In flooring on a bed of 10mm thick mortar 1:4 (1 acid proof cement :4 coarse sand). |
| 22 | Extra for pre finished nosing to treads of steps of marble stone. |
| 23 | Extra for marble stone flooring, skirting, in treads of step and risers using single length up to 2.00 metre. |
| 24 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make, in all colours and shades laid on 20 mm thick Cement Mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x800 mm. |
| 25 | Tile work in skirting, risers of steps and dado up to 2 in height over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm., including pointing in white cement mixed with pigment of matching shade complete. |
| 26 | Providing wood works in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required diameter & length.Sal wood. |
| 27 | Providing and fixing panelled or panelled and glazed shutter for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid seperately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid seperately). Sal wood. 35mm thick shutters. |
| 28 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glaze shutter for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25mm to 40mm thick: Sal wood. |
| 29 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T- iron 40x40x6mm, with 40mm dia. Steel pulleys, complete with bolts, niuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. |
| 30 | Providing and fixing M.S. grills Of required pattern in trames Of windows, etc. with M.S. flats, square or round bars, etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc. |
| 31 | Earthwork in filling (excluding rock) in trenches, plinth, sides of foundation etc in layers not exceeding 20cm thick including breaking of clods, consolidating each layer by ramming and watering, lead upto 50m and lift upto 1.5m. With borrowed earth/ stone dust carriage upto 5KM. |
| 32 | Sand filling in plinth in layers not exceeding 150 mm thick including breaking of clods, consolidating by ramming and watering complete as directed. (Maximum depth 45 cm). |
| 33 | Cement concrete floor topping 1:1:2 ( 1 cement: 1 Coarse sand: 2 stone aggregate) finished with floating coat of neat cement, icluding cement slurry, complete.20 mm thick. |
| 34 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the palstered wall surface to prepare the surface even and smooth complete. |
| 35 | Finishing walls with textured exterior paint of required shade, including scaffolding: New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm. |
| 36 | Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) with ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood. |
| 37 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: New work (two or more coats over an under coat of suitable shade with ordinary paint of approved brand and manufacture). |
| 38 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of requires size, on top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered). |
| 39 | 50mm thick cement concrete flooring with comcrete hardener topping, under layer 38mm thick cement concrete 1:2:4( 1 cement: 2Coarse sand: 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1cement hardener mix: 2graded stone aggregate 6mm nominal size) by volume, hardening compound mixed @ 2litre per 50 kg of cement or as per manufacturer's specifications. This includes coat of cement slurry, complete. |
| 40 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:250x10 mm |
| 41 | Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm |
| 42 | Providing and fixing bright finished brass door latch with necessary screws etc. complete:300x16x5 mm |
| 43 | Providing and fixing bright finished brass butt hinges with necessry screws etc. complete: 125x85x5.5xmm (heavy type) |
| 44 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS: 3564, embossed on the body, door weight up to 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete: |
| 45 | Providing and fixing chromium plated brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete: |
| 46 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete: |
| 47 | Providing and fixing aluminium pull bolt lock, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: |
| 48 | Providing and fixing aluminium handles, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:125 mm |
| 49 | Providing and fixing aluminium casement stays, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: |
| 50 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ approciate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required diameter and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the direction of Enginner-in-charge. (Glazing, and panelling to be paid for seperately):(a) For fixed portion(i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 51 | (a) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for seperately)(i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 52 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge:With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 53 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and directions of engineer-in-charge: |
| 54 | Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc. complete directions of engineer-in-charge. Anodized (AC 15) aluminium tubular handle bar |
| 55 | Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc complete.Anodized (AC 15) aluminium |
| 56 | INTERNAL WATER SUPPLY AND SANITARY FITTING |
| 57 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter . |
| 58 | (a) 110 mm diameter. |
| 59 | Providing and fixing water closet squatting pan (Indian Type W.C. pan) with 100mm sand cast iron P or S trap, 10 litres low level wide PVC flushing cistern, including flush pipe, with manual controlled device (handle lever) conforming to IS:7231 , with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:(a) White vitreous China or Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 60 | Providing and fixing white vitreous China Pedestal type water closet (European Type) white seat and lid, 10 litre low level wide vitreous Chin flushing cisterns & C.P . flush bent with fittings & C.I brackets, 40 mm flush bend, over flow arrangement with specials of standard make and mosquito proof coupling of approved design complete including painting and fittings and brackets, cutting and making good the walls and floors wherever required:(b) W.C. pan with ISI marked black solid plastic seat and lid. |
| 61 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40 mm C.P brass trap with necessary C.P brass unions complete, including painting of fitting and brackets, cutting and making good the walls wherever required: Size 600x450x200 mm. |
| 62 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:(i) With vitreous China Surgeon type wash basin of size 660x460 mm with single of 15 mm C.P. brass pillar taps with elbow including operated levers ISI marked. |
| 63 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 64 | Providing and fixing 8 mm dia C.P/S.S Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.c. of quality and make as approved by Engineer-in-Charge. |
| 65 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer -in-charge. |
| 66 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.(b) Flexible pipe.32 mm dia and 40 mm dia. |
| 67 | Providing and fixing mirror of superior glass (of approved quality) and or required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Circular shape 450 mm dia. |
| 68 | Providing and fixing toilet paper holder:C.P. brass |
| 69 | Providing and fixing soil, waste and vent pipes: 100 mm diameter. (i) Sand cast iron S & S pipe as per IS: 1729. |
| 70 | (a) 75 mm diameter. (i) Sand cast iron S & S pipe as per IS: 1729. |
| 71 | Providing and filling the joists with spun yarn, cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I./ C.I. Pipes: 75 mm diameter. |
| 72 | (a) 100 mm diameter. |
| 73 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/ cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10xcm of 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the wall etc.:For 100 mm dia. Pipe and for 75 mm dia pipe. |
| 74 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete with sand cast iron S&S as per IS: 1729:(a) 100 mm diameter . |
| 75 | (a) 75 mm diameter . |
| 76 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. |
| 77 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. Size 600 mm. |
| 78 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal for hot & cold water supply, including all CPVC Plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipe & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge.Concealed work, including cutting chases and making good the wall etc.15 mm nominal outer diameter Pipes. |
| 79 | (a) 25 mm nominal outer diameter Pipes |
| 80 | Providing and fixing brass bib cock of approved quality:20 mm nominal bore. |
| 81 | Providing and fixing brass stop cock of approved quality:20 mm nominal bore. |
| 82 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):25 mm nominal bore. |
| 83 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 25 mm nominal bore. |
| 84 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 85 | Providing and fixing PTMT pillar cock of approved quality and colour.15 mm nominal bore, 107 mm long, weighing not less than 110 gms. |
| 86 | Providing and fixing PTMT extension nipple for water tank pipe, fitting of approved quality and colour.25 mm nominal bore, weighing not less than 62 gms |
| 87 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concelaed fitting arrangements, weighing not less than 106 gms. |
| 88 | INTERNAL ELECTRIFICATION |
| 89 | Wiring in looping system with copper PVC cable 250/440 volt grade of size 1.5 sqmm of approved quality using PVC casing capping including 5 amperes switch Indian best quality ceiling rose etc. capable to a highest point.Long point wiring upto 10mts. |
| 90 | Wiring as in item No.1 complete to a light plug point when fixed on the same board. |
| 91 | Wiring to a power plug as in item No.1 above with continous earth wire complete. Long Point wiring upto 10mts. |
| 92 | Wiring as in item No.1 above to staircase /Two way switch wiring.Long point wiring upto 10mts. |
| 93 | Wiring as in item No.1 above to a Ceiling /Exhaust Fan Point.Long point wiring upto 10mts. |
| 94 | Wiring as in item No.1 above to a Callling Bell/Bell indicator point control by 5amp Bellpush. Long point wiring upto 10mts. |
| 95 | Drawing of Main and Sub-main line with DGSD approved VIR or PVC 250/440 Volt grade copper conductor in PVC casing capping complete with all accessories.(a)With 2×2.5mm2 Copper Conductor. |
| 96 | (a) With 2×4 mm2 Copper Conductor. |
| 97 | (b) With 2×6 mm2 Copper Conductor. |
| 98 | Drawing of 3 phase main line 4 wire with DGSD approved VIR or PVC cable 660 volt grade in casing capping with all accessories.With 4×16mm2 Copper Conductor. |
| 99 | Supplying fittings and fixing complete Switch Fuse Unit (S.F.U) sheet steel Re-wirable main switch with Pre-Fitted Fuse Wire 50Hz.240/415V.(B) 3 Pole with Neutral(T.P.N)200 Amp 415V Capacity. |
| 100 | Supplying fittings & fixing complete 240/415V AI.Bus Bar Chamber.(ii) TPN 4 Ways. 200 Amp 415V Capacity. |
| 101 | Supplying and fixing of Load Kontaket Miniature Circuit Breakers DX3 MCB,s for AC aplication till 63 Amp.(D) Triple Pole 415V. 6-32Amp. |
| 102 | Supplying fitting and fixing of DX3 Isolators for AC applications upto 125A(B) Triple Pole 415V63Amp. |
| 103 | Supplying fitting and fixing of distribution Board SPN DB's for MCB Isolator,RCCB and RCBO.(A) IP 30 -#1K08 . 4 Way + 4Module. |
| 104 | Supplying fitting and fixing of distribution Board ETPN DB's for MCB Isolator,RCCB and RCBO.(A) IP 30 -#1K08 . 4 Way 8+12Module. |
| 105 | Supplying fitting and fixing complete polish brass bracket,16mm dia and 23cm long with cast backplate and brass lamp holder with LED bulb surface or wall mounted with all necessary accessories. 9W. |
| 106 | Supplying fitting and fixing of LED RETROFIT LAMPS surface or wall or mounted with all necessary accessories.(c)Photon ultra LED tubelight (Single side connection ). 20W |
| 107 | Supplying fitting,connecting ,testing and commissioning of calling bell/Bell indicator type suitable for 230 volt as well as battery operated complete with all necessary accesessories Musical calling bell. |
| 108 | Supplying and fitting of ceiling fan AC operated type 220/250 volt. Complete with 3 Nos of blades down rod canopy hanging shackle & 30mm length down rod supplied with the fan by the dealer but the extra length will be charged @ Rs25.00/ mtr. AC ceiling Fan '1200'mm sweeps. |
| 109 | Supplying fitting and fixing of exhaust fan double bearing selft lubricating type single face 50Hz 250V AC operated complete with supporting frame fan blades,nuts and bolts and other petty accessories as required.Metal exhause fan 300mm. |
| 110 | Supplying fitting and fixing of AC .With heating and cooling facility including supply of all necessories accessories as required for installation of Air conditioner AC.1.5 ton capacity. |
| 111 | Supplying fitting and fixing of Copper lighting Arrester with 5nos. Finger at the top &copper base plate at the bottom complete. With 3ft hight Copper rod. |
| 112 | Supplying fitting & fixing earthing with copper earth plate 600×600mm×6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal , salts etc complete as required. Copper earth plate electrode. |
| 113 | Supplying and laying of 15mm×15mm GI/ Copper Strip at 0.50 mts,below ground.25mmx5mm copper strip. |
| 114 | Supplying fitting and fixing of SREET LIGHT surface or wall mounted with all necessary accessories.(b) LED sreeet light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having protection and impact resistance with 10KV Built - in Surge protection device 100W suitable for pole dia ɸ 58mm (max) |
| 115 | Supplying fitting and fixing of industrial type socket 15Amp complete with all necessary accessories as required.15 Amp Industrial type socket. |
| 116 | Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized pedestal/ floor mounted Power Supply Panel Board of approved size and 450mm deep made out of 2 mm thick CRCA sheet steel with suitable size compartments, Al. bus bars, switchgears, voltmeters, ameters with selector switches etc including powder coating painting with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, PWD standards and Electrical Inspectorate standards.(E) The panel board shall house :1 No 4 pole 400A MCCB, 65kA as Normal Supply Incomer;4 Pole 300 A Al. busbar;3 Nos. Current transformer of 200/5A;1 No Ammeter with selector switch:1 No 0-500V Voltmeter with selector switch;3 Nos. LEDs: 7 Nos 4 pole, 63A MCB, 25kA as outgoing feeders9 No.s DP,40A MCB,KA as outgoing feeders Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 27, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Sep 29, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 16 daysSep 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender