Tender For Replacement Of 30 Cusec Vt Pumping Unit Having 7 Meter Head By Way Of Supply, Installation, Testing And Commissioning Of New Pumping Unit Along With Starter And Cables Etc At Lis Shalteng Of Misd Shadipora.
Tender Value
40 Lakhs
Estimated cost
Bid Submission
07 Sep 2026
9 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ganderbal → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Replacement Of 30 Cusec Vt Pumping Unit Having 7 Meter Head By Way Of Supply, Installation, Testing And Commissioning Of New Pumping Unit Along With Starter And Cables Etc At Lis Shalteng Of Misd Shadipora.
BOQ
| Sl. No. | Item Description |
| 1 | Design, Manufacture, Supply, installation, testing & commissioning of Vertical Turbine pump motor unit of specified duty parameters with specified capacity vertical solid shaft TEFC squirrel cage induction motor of following Specifications:i) Type Vertical Turbine, Mixed Flow Pump ia) Make: Kirloskar/WILO/Flowmore/WPIL or Equivalent as approved in EOMs List issued by Superintending Engineer Mechanical Circle I&F Dept. Srinagar. ii) Discharge of pump: 30 cusec (3058 m3/hr) iii)Dynamic Head: 7.00 m iv) Rated Speed: Suitable for the guaranteed duty point not exceeding 1000 RPM v) Pump Efficiency: Not less than 80 % at the guaranteed rated duty point. vi) Fluid to be handled: Raw Water River vii) No. of stages: Single viii) Duty: Continuousix) Column pipe size 500mm ND or as required as per discharge and design x) Overall length of Column pipe along with Bell mouth, diffuser and Discharge Bend: 7.86 mxi) Location of Discharge Elbow: Below Machine Floor LevelMaterial of constructionCasing: Cast Iron FG260Impeller: Stainless steel SS410Bowl & Suction Bell: Cast Iron FG260Shaft/ Shaft coupling: AISI 410 Stainless SteelShaft Sleeve: AISI 410 Stainless SteelColumn Pipe: MS ERW (Min.thickness 8mm)Base Plate: MSSuction Strainer: SSMotor specifications:i)Rating of motor: Motor rating shall be adequate for the max power absorbed by the pump over the specified operating range and shall not be Less than 110 HP, and the motor shall not overload at any point within the specified operating range .ii)Frequency: 50± Hz iii)Phase Three phase iv)Voltage: 415±10%v)Efficiency: Minimum IE2vi) Insulation Class: F or abovevii) Enclosure: TEFC VIII) RPM: Not exceeding 1000 The Job includes fabrication and fitting of foundation/ support structure using requisite ISMB beams, channels, chequered plate as per site requiremnets for fixing of sole plate etc including commissioning at site and the testing at full load. The Job shall also include any modifictions required for proper fitting/alignment of the pumping unit with the existing delivery line. |
| 2 | Providing, installation, testing and commissioning of 120 Sq mm, single core, PVC insulated, un-armoured copper LT power cable confirming to ISI Standards. The cable shall be multi stranded, having sequential marking on outer sheath. Acceptable make shall be Finolex/ L&T/ Havells/ Gloster/KEI/ Polycab or equivalent. |
| 3 | Supply, Installation Testing and Commissioning at site 125 HP Cubical and pedestal type Fully automatic Star Delta starter. The starter shall comprise of the following equipment and accessories.a) Main Contactor Assembly 225 Amp AC3 (01 No).b) Delta Contactor Assembly 225 Amp AC3 (01 No). c) Star Contactor Assembly 140 amp AC3 (01 NO)d) Thermal overload Relay of with 132–220-amp Relay range.e) Double vacuum timer assembly having time range of 0-60/sec.f) Single phase preventer.g) Auxiliary fuse units of suitable Ampere range.h) Electrolytic Copper bus bar strips of suitable size of duly tinned air insulated mounted on suitable size backlit insulators.i) 01 no 3 Phase Digital Ampere meter which indicate 0 to 300 Ampere amperage with required attachments.j) One number 3 Phase Digital voltmeter 0-500 volts.k) On/Off push button Switch’s.l) Complete internal wiring of the Control panel for operation of the equipment by using adequate capacity of Single/Multi strand copper wire of standard make. The wiring shall be provided with plastic washers for identification of each wire at various joints. The wiring shall have to complete properly.m) Main 3 Pole MCCB of Suitable Rating. (01 no) n) Cubical Panel fabricated out of 1.5/2.0mm CRCA Sheet with angle 40x5 mm The job further includes P/F of 120 Sq.mm Single core multistrand, PVC insulated copper cable (20mts) with proper thumbing for connecting Starter with the existing electrical circuit/system. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysSep 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender