Tender For Construction Of Kitchen Shed For Govt.High.School At Kalangal In Sulur Block , Coimbatore Districtr Under Ugf Fund / 2026-27
Tender Value
3.75 Lakhs
Estimated cost
Bid Submission
17 Sep 2026
1 days left
EMD
4000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Coimbatore → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Kitchen Shed For Govt.High.School At Kalangal In Sulur Block , Coimbatore Districtr Under Ugf Fund / 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | 1.Construction of Kitchen shed for Govt.High.School at Kalangal in Sulur Block , Coimbatore Districtr under UGF Fund / 2026-27 |
| 2 | Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and cleaning and levelling the site etc.,complete - |
| 3 | Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hard broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted, etc., complete complying with standard specfication. |
| 4 | Refilling with selected excavated earth complying with standard specifications for refilling in foundation and basement etc., complete as directed by the departmental officers |
| 5 | Brick work in cement mortar 1:5 (One of cement and five of sand) using Fly ash bricks in Basement and in Ground floor including fixing the frames of doors and windows, scaffolding, proper setting, curing, etc., complete in all respects. |
| 6 | Supplying and erecting centering for sides and soffits including supports for all reinforced cement concrete works like lintels, beams, etc., including strutting 3M high using Mild steel sheets of size 90cm × 60cm and B.G. 10, stiffened with Mild steel Angles of size 25mm × 25mm × 3mm laid over Silver oak (cw) joists of size 10cm × 6.5cm (Spaced about 91cm c/c) and supported by casurina props of 10cm to 13cm dia (Spaced at 75cm c/c) as noted below including removing the same after specified period without damaging RCC works in all floors etc., complete as directed by the departmental officers complying with relevant standard specifications (Above Ground level) |
| 7 | Fabricating and placing the steel grills for reinforcement for all reinforced cement concrete works such as plinth beam, lintels, beams, sunshade, roof and floor slabs etc., including cost of steel and fabricating the reinforcement grills in position etc., complete in all floors (The rate to include the cost of binding wire steel also) |
| 8 | Reinforced Cement concrete 1:1.5:3 using 20mm gauge hard broken granite stones for all reinforced cement concrete works viz. Raft slabs, raft beams, column footing, plinth beam, lintel, square or circular columns, T, L, or rectangular beam , floor, roof or waist slab, drop cum parapet wall, loft, sun shade and other similar works excluding the cost and fabrication of reinforcement grills in position, shuttering, centering but including laying, vibrating, curing, finishing and providing Mild steel fan hooks in the RCC slab wherever necessary as directed by the departmental officers etc., complete in all respects. |
| 9 | Special RCC surface plastering with cement mortar 1:3 (One of cement and three of sand) 10mm thick including finishing smooth, proper setting, curing etc., complete as directed by the departmental officer |
| 10 | Plastering the walls with cement mortar 1:5 (One of cement and five of sand) 12mm thick including finishing smooth, scaffolding, setting, curing etc., complete as directed by the departmental officers. |
| 11 | Providing the following thickness of Granolithic pattern floor finish with Plain Cement concrete 1 : 2 : 4 mix using 10-12mm ISS HBG metal and the top rubed smooth etc., |
| 12 | Cost and Supply of MS Tubular section pipes for Truss and Purlin including cost and conveyance of all materials and labour charges etc complete |
| 13 | Supply and fixing of PUF roof panels made up of 60mm thick PPGI corrugated Sheet at the top and a plain sheet at the bottom with a layer of rigid CFC free polyurethane foam (PUF) of density 40kg + 2 Kg/cum as insulation in between .The polyurethane foam shall confirm to latest IS 12436. The minimum thickness of PU foam layer shall be 29mm for having 30mm (min) thick PUF panel. The PPGI Sheets shall be of minimum 240 MPA Steel Grade & shall have a Zinc coating of minimum 120 GSM as per IS 277/1992, 5-7 microns of epoxy primer on both sides of the sheet & polyester top coat of 18-20 microns on one side / outer side. The PPGI Sheets / PUF Panels shall have a protective guard film of minimum 20-25 microns to avoid scratches to finished panel during transportation. Providing ridges or hips ,encasing the ends of Panel with plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers etc complete excluding the cost of trusses, purlins and inclusive of cutting to size and shape wherever required. |
| 14 | Distembering two coats with best approved oil bound distember including cost of painting priming coat over new plastered surface and conveyance of all materials to site and all labour charges in all etc completed |
| 15 | Painting the walls and ceiling two coats with approved emulsion paint over one coat of priming coat of emulsion including cost and conveyance of all materials to site, through scrapping of old plastered surface, preparing the surface, curing etc., complete |
| 16 | Painting with enamel paint two coats over Mild steel doors and windows including all charges in all etc complete |
| 17 | Towards the cost and supply of Mild steel doors of following sizes including all charges in all etc complete |
| 18 | Towards the cost and supply of Mild steel doors of following sizes including all charges in all etc complete |
| 19 | Labour charges for fixing doors as directed by the departmental officers in all etc complete |
| 20 | Labour charges for fixing Windows as directed by the departmental officers in all etc complete |
| 21 | Supply and run of 2 of 4 sq. mm ( 84/0.30) polythene insulated and PVC unsheeted S.C. Alu cable of 1100 V on 7/20 Gi bearer wire for Service Connection Main - SD.65 Service connection wire |
| 22 | Supply and run of 2 of 4 Sq.mm (56/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in 25mm dia GI Pipe (Class 'B') suitably bent at both ends with necessary angle iron upright and supports for mains SD-70 Service GI pipe |
| 23 | Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1\\" x 1/8\\" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1\\" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit SD-125 |
| 24 | Supply and fixing of 16 Amps DPIC switch of 500V grade with Fuse and Nutral on suitable T.W. board with painting of suitable colour with PWD Earthing SD No.141 16 Amps DPIC Switch |
| 25 | Wiring with 2 × 1.5 sq.mm (22/0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Teak wood switch box with 5A F.T. switch inflush with wih wall covered with hylem sheet of 3mm thick with painting of suitable colour of open PVC light point / fan point (For electronic regulator) - SD 20 Light / Fan Pont |
| 26 | Wiring with 2 × 1.5 sq.mm (22/0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150mm×100mm×113mm Teak wood switch box for 5A 3 pin non interlocking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point - SD 36 Plug Point |
| 27 | Supply and fixing of WT bulk head fitting with guard (Philips/Bajaj/Crompton/K- Lite) suitable for 11W CFL lamp with CFL - SD 83 Bulk head fitting |
| 28 | Supply and fixing of single box type 4' 40W flu. Fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu. Tube with PVC unsheathed copper leads from terminals to the fitting.- SD 88 Tube Light |
| 29 | Supply and fixing of 375mm (15\\") sweep (light duty) AC exhaust fan complete without provision of holes in the wall.- SD 117 |
| 30 | GST Amount for providing Service to Government Contract Works for the above Construction & maintenance Works. { GST Amount is the Total GST Amount for overall quoted amount (for Construction & maintenance) above this row in column \\"BB\\" for all works in this package} Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 daySep 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender