Tender For Construction Of A New Toilet Facility At Hwpk Housing Colony.
Tender Value
2.88 Lakhs
Estimated cost
Bid Submission
26 Sep 2026
0 days left
EMD
5774
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chittorgarh → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of A New Toilet Facility At Hwpk Housing Colony.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 16-Sep-2026 | corrigendum12026117 | Date | 26-Sep-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in Excavation in all type of soil/base caurse, Soft and ordinary rock etc. by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) bailing out of water if encountered over areas including refilling around foundation, plinth,in layers, watering, consolidating and disposing of all surplus excavated/broken materials upto a lead of 2KM and lift of 1.5 meter, disposed earth to be levelled and neatly dressed all as per drawing, specifications and as directed by the Engineer-In-Charge. |
| 2 | Surface dressing of the ground all type of soil including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 3 | Providing and laying in position Cement concrete 1:3:6 (1 cement, 3 coarse sand, 6 graded stone aggregate of 20mm maximum size) including consolidation, finishing, curing etc. but excluding the cost of form work, shuttering, centering complete as per specifications and as directed by the Engineer. |
| 4 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Cement mortar 1:4 (1 Cement:4 Coarse Sand) in superstructure above plinth level up to floor V level in all shapes, sizes required slope, including providing necessary scaffolding, curing etc. complete as per the specifications and as directed by EIC. |
| 5 | Half Brick work with common burnt clay F.P.S.(non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) including all materials, manpower, scaffolding and including fixing door frame (door frame proveded by department)wherever required etc. complete as pr specifications and as directed by the Engineer In Charge. |
| 6 | Providing and laying in position Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20mm maximum size) including consolidation, finishing, curing etc. complete as per specifications but excluding the cost form work shuttering, centering complete as per the specification and as directed by the Engineer. |
| 7 | Plastering with 15 mm cement plaster in 1:4 mix (1 cement: 4 fine sand) at all heights including providing scaffolding, curing etc. complete as per specifications and as directed by Engineer in charge. |
| 8 | Supply and laying/fixing of PVC Nahani trap of 4\\" dia. in position of Jain/ Finolex/ Kitec /Supreme /Prince make IS - 4985 of latest version with fixing arrangements for drainage/ sewerage works as per stantard specifications etc. complete as directed by the Engineer in charge. |
| 9 | Providing and fixing of size 15mm NB class 'B' G.I. Pipes complete with G.I. fittings and clamps for external work i/c making good the walls etc. complate as per the specifications and as directed by EIC. |
| 10 | Providing and fixing 15 mm nominal bore with 45 cm length unplasticised PVC Connection pipe with PTMT Nut, collar and brush of approved quality like prayag make Cat No. 323 or equivalent make complete as per the specification and as directed by EIC. |
| 11 | Providing all tools, tackles, materials, manpower for structural steel work in built up sections at all height, including cost of cutting, welding, hoisting, fixing, transport, loading, unloading, necessary scaffolding and applying a priming coat of approved steel primer all complete etc., all complete as per the specification and as directed by the Engineer in charge. |
| 12 | Providing and fixing White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests of aproved make like Jaguar/parryware/somany or equivalant make with 100 mm sand cast Iron P or S trap, 10 litre white P.V.C. flushing cistern, including long flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete as per the specifications and as directed by EIC. |
| 13 | Providing and fixing Flat back wash basin of size 550*400 mm with single 15mm C.P. brass pillar tap, C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require complete as per the specifications and as directed by EIC. |
| 14 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 15 | Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment, Curing etc., complete all as per the specifications and as directed by EIC. |
| 16 | Providing and fixing Ist quality ceramic rectified glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade, including cutting for openings, curing etc. complete as per the specifications and as directed by EIC. |
| 17 | Providing and fixing ISI marked 35 mm thick flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality, including ISI marked Stainless Steel butt hinges with necessary screws etc. complete as per the specifications and as directed by EIC. |
| 18 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 including wall flange etc complete as per the specifications and as directed by EIC. |
| 19 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality including wall flanges conforming to IS:8931 etc complete as per the specification and as directed by EIC. |
| 20 | Providing and fixing One urinal basin with 5 litre white P.V.C. automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete as per the specification and as directed by EIC. |
| 21 | Providing and fixing 15 mm nominal bore C.P. brass stop cock, standard design and of approved make conforming to IS:8931 including wall flage etc complete as per the specifications and as directed by EIC. |
| 22 | Supply and laying/fixing of unPlasticised Rigid PVC PIPES of 110mm dia-4kg/cm2, in position approved PVC pipes of Jain/ Finolex/ Kitec /Supreme /Prince make IS - 13592 Type A of latest version for water supply/ sewerage works as per stantard specifications and providing and fixing approved nails quality clamps and screws for fixing as per requirements as directed by the Engineer in charge. |
| 23 | Supply and laying/fixing of unPlasticised Rigid PVC drain bend 4\\" dia. in position of Jain/ Finolex/ Kitec /Supreme /Prince make IS - 13592 Type A of latest version with fixing arrangements for drainage/ sewerage works as per stantard specifications etc. complete as directed by the Engineer in charge. |
| 24 | Providing and fixing 600 mm long PTMT towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour etc complete as per the specifications and as directed by EIC. |
| 25 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per the specifications and as directed by EIC. |
| 26 | Providing and fixing colour coated corrugated galvalume profile sheets of TATA/JSW or equivalant make (Profile, Colour and shape as approved by the Engineer-incharge) of 0.50mm (TCT) total coated thickness (tolerance as per relevant IS code) with material yield strength 550 MPa, galvalume AZ-150 (zinc aluminium alloy coating nominal composition : 55% aluminium, 43.5% zinc & 1.5% silicon mass total of both sides) with regular modified polyester paint and coating of 20- 25 micron RMP on exposed surface including primer and 7-10 micron epoxy coating on unexposed surface including primer. The sheet should be supplied in single length as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping screws with EPDM seal and washers of make- Coroshield/ durotuff / polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers( as per engineer in charge) including cutting to size and shape wherever required etc. complete as per the specifications and as directed by EIC.Note:1. All screw should be sealed with silicon sealant.2. Measurements will be given only for covered Roof area and over laps will not be measured or paid separately. |
| 27 | Providing and applying white cement based putty of average thickness 1 mm, Birla white wall care putty over the plastered wall surface to prepare the surface even and smooth complete including applying additional coats wherever required to achieve evensurface, including preparing surfaces, scaffolding & cleaning etc. complete all as per specifications & as directed by the Engineer-in-Charge. |
| 28 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour for New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre . complete and as directred by the Engineer. |
| 29 | Painting Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade (ready mixed) of approved brand,manufacturer of required shade and colour New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm),filling the unever surfaces with J K or eqivailant make wall putty, sand papering, making the surface smooth and even etc. complete as per manufacturer’s specification, cleaning of paint splashings and droppings from floors, doors & windows etc. complete and as directred by the Engineer. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 16, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Sep 26, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
TodaySep 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayOct 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender