Tender For Construction Of Student Toilet Complex At Firing Range Of Cdo Trg Area, Construction Of Toilet Complex With Urinal Pts At Bldg No Gb-09 And Provn Of Parking Shed Near Build No. P-01 Harding Lines Of Demo Tps Of Hq Jl Wing, The Inf School B
Tender Value
44.50 Lakhs
Estimated cost
Bid Submission
15 Sep 2026
2 days left
EMD
89000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Belagavi → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Student Toilet Complex At Firing Range Of Cdo Trg Area, Construction Of Toilet Complex With Urinal Pts At Bldg No Gb-09 And Provn Of Parking Shed Near Build No. P-01 Harding Lines Of Demo Tps Of Hq Jl Wing, The Inf School Belagavi Under Ge Belgaum
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in any type of soil, including removal of the rubish upto 50m, complete all as specified and as directed. |
| 2 | Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep as in any type of soil, for foundation etc., or for laying of cable/ GI Pipe, shafts, wells, cesspits, manholes, pier holes, etc., complete all as specified. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil, as in soft disintegrated rock, complete all as specified. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. |
| 4 | Removal of excavated material [soft rock] to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified. |
| 5 | M&L for Moorum/Red bajri filling brought from out side MD land including filling in floors or pavings or in foundations laid in layers n.exc. 15cm thick spread, levelled and rammed including watering, complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. |
| 6 | M&L for Hardcore of gauge not exc. 63mm, broken stone or boulders, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface, complete all as specified and as directed. |
| 7 | M&L for PCC 1:4:8 type D2 (using 40mm graded Granite stone aggregate) as in foundation, post holes, filling, mass concrete etc., complete all as specified and as directed. |
| 8 | M&L for Reinforced cement concrete M-25 Grade (Design mix) as in foundations, including footings, foundation beams, plinth beams, bases for columns, basement slabs, and mass concrete or similar items etc., complete all as specified and as directed. |
| 9 | M&L for Reinforced cement concrete M-25 Grade (Design mix) as in columns, Pillars, piers, vertical bands, posts and struts etc., complete all as specified and as directed. |
| 10 | M&L for Reinforced cement concrete M-25 Grade (Design mix) as in floor beams, roof beams, cantilevers, bressumers, middle beams, lintels over 1.5m span and lintel bands etc., complete all as specified and as directed. |
| 11 | Steel formwork to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces of concrete, complete all as specified and as directed. |
| 12 | Steel formwork to sides of pillars, posts, struts, columns, stanchions and the like, for fair finished surfaces of concrete, complete all as specified and as directed. |
| 13 | Steel formwork to sides and soffits of floor or roof beams, cantilevers, bressummers, lintels, shelves, lintel beams, RCC bands, girders etc., for fair finished surfaces of concrete, complete all as specified and as directed. |
| 14 | M&L for Reinforcement using TMT bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. |
| 15 | M&L for Reinforcement using TMT bars of Grade Fe-500D of 8mm dia and over upto and including 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded complete all as specified. |
| 16 | M&L for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, complete all as specified and as directed. |
| 17 | M&L for PCC type B1 1:2:4 (using 20mm graded stone aggregate) as in cast in situ in lintels up to 1.5m span, cills, steps, plinth courses, copings, bed plates, roof padding and the like, including weathering, slightly rounded or chamfered angles and throating and including necessary form work complete all as specified and directed by Engineer-in-charge. |
| 18 | M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces of walls in CM 1:6 finished even and fair without using extra cement complete all as specified and as directed. |
| 19 | M&L for 15mm thick Rendering on fair faces of brick work or concrete surfaces in two layers as 10mm thick in cement mortar 1:6 followed by 5mm thick in cement mortar 1:4 mixed with and including water proofing compound @3% of weight of cement and finish the surface even and smooth without using extra cement, complete all as specified and as directed. |
| 20 | M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces of walls in CM 1:4 finished even and fair without using extra cement complete all as specified and as directed. |
| 21 | M&L for preparation of new surfaces of walls and applying three coats of white wash on newly plastered surfaces of wall, complete as specified and as directed. |
| 22 | M&L for applying two coats of oil boun distemper with and including a coat of wall care putty and priming coat of alkali resistant primer, with and including preparation of newly plastered surfaces, all as per manufacturer's instructions, complete all as specified and as directed. |
| 23 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over with and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, with and including preparation of newly plastered surfaces, all as per manufacturer's instructions, complete all as specified and as directed. |
| 24 | S&F Factory made Steel Ventilator with top hung shutter, with and including hinges, steel peg stay etc., complete all as specified. |
| 25 | M&L Framed work such as grills, gratings, hold fasts, wind ties, rungs etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars, flats, hold fasts, barred iron doors, ladder, framed baluster, walk ways, railings, and similar work confirming to Fe-290, Gde E-165, complete all as specified. |
| 26 | S&F Minimum 4.0mm thick sheet glass of ordinary quality of approved brand fixed in position as in doors, windows, partitions etc., as in squares exceeding 0.50 Sqm in each pane etc., with all required accessories, complete all as specified and as directed by Engineer-in-charge. |
| 27 | S&F Stainless Steel butt hinges, medium weight 100mm size, ISI marked, complete all as specified and as directed. |
| 28 | S&F 150mm long Extruded aluminium alloy 'D' type handles, fabricated type, anodised complete all as specified and as directed. |
| 29 | S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete, complete all as specified and as directed. |
| 30 | S&F Aluminium anodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified and all as directed. |
| 31 | M&L for 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded granite stone aggregate) as in sub base of flooring, complete all as specified and as directed. |
| 32 | M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded granite stone aggregate) as in sub base of flooring, complete all as specified and as directed. |
| 33 | M&L for 75mm thick PCC 1:3:6 type C1 (using 20mm graded hard granite stone aggregate) as in plinth protection, finished even and fair without using extra cement including making construction joints in 3m interval and joint filled with sealing compound, complete all as specified and as directed. |
| 34 | M&L for Machine cut Granite stone slab, 20mm thick, as in wall lining (veneering to wall / gate pillars) cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the tiles with and including 15mm thick backing coat in CM 1:3, bull nosing the edges, rubbing and polishing, complete all as specified and as directed. |
| 35 | M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exc. 0.11 Sq.m. but n. exc. 0.18Sq.m, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, complete all as specified. |
| 36 | M&L for Premium quality, joint free ceramic glazed coloured wall tiles of 7 to 8mm thick (square / rectangular) area of each tile not exc 0.36Sqm, on vertical surfaces such as dado and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over & including 10mm thick rendering in CM 1:3, complete all as specified. |
| 37 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window Frame/ Chowkhat of size 45mm x 70mm with virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate & natural fibbers (wood powder/ rice husk/ wheat husk) & non toxic additives (maximum toxicity index of 12 for 100 gms) with mitre joints after applying PVC solvent cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant, and fixed in position, complete all as specified. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 38 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension rade), calcium carbonate and natural fibbers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant, complete all as specified and as directed. |
| 39 | M&L for Factory made Machine pressed Rubber coated chequered cement concrete coloured tiles 23-25mm thick, of approved shape and size, as in floor / path, set, jointed and pointed in neat cement slurry with grey cement and pigment, glosy finish on top, laid over and including 15mm thick screed bed in CM 1:4, complete all as specified. |
| 40 | M&L for Factory made Machine pressed pre-cast cement concrete interlocking paver block of any shape and size with glossy finish on top, confirming to IS 15658-2006 of 60mm thick, M-35 grade with grey cement and pigment, with and laid over and including 50mm thick sand cushion (crushed stone sand / M sand) under paver block including watering and consolidation, complete all as specified and as directed. |
| 41 | S&F 110mm bore uPVC (SWR) soil, waste and vent pipe, single socketed in any length with rubber ring joints, fixed to wall with brackets, complete all as specified and as directed. |
| 42 | S&F 75mm bore uPVC (SWR) soil, waste and vent pipe, single socketed in any length with rubber ring joints, fixed to wall with brackets, complete all as specified and as directed. |
| 43 | S&F uPVC (SWR) bend any radius with access door, suitable for 110mm bore pipes, including jointing with solvent, complete all as specified and as directed. |
| 44 | S&F uPVC (SWR) Junction (Single Y) equal or unequal, suitable for 110mm bore pipes, including jointing with solvent, complete all as specified and as directed. |
| 45 | S&F uPVC (SWR) Floor / Nahani trap with grating of 75mm dia outlet, setting and jointing with solvent, complete all as specified and as directed. |
| 46 | S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), ISI Marked, three layered, 1000 Litres capacity, hoisted and fixed in position all as specified in SSR Part I, with and including high pressure 25mm dia PTMT ball valve with epoxy coated aluminium rod with high density plastic ball, complete all as specified. |
| 47 | S&F 600mm x 450mm bevelled edge mirror 6mm thick of selected quality glass mounted on 6mm thick commercial plywood/ AC building board and fixed to wooden plugs with CP brass screws and cup washers and provision of wooden beading around the mirror, complete all as specified and as directed. |
| 48 | S&F Vitreous china Wash down water closet pan EWC (Pedestal pattern), white with 'P'or 'S' trap étc, (excluding flushing cistern and flush pipe) with and including plastic water closet seat cover closed pattern with flat bottom cover, mild steel chromium plated or aluminised hinging device, fixing bolts, etc, complete all as specified and as directed. |
| 49 | S&F uPVC (SWR) grating doom 150mm dia with / with waste hole, fixed with white cement, complete all as specified and as directed. |
| 50 | S&F uPVC (SWR) gully trap of 125/110mm dia outlet, setting and jointing with solvent, complete all as specified and as directed. |
| 51 | S&F uPVC (SWR) Vent Cowl suitable for 110mm bore pipes, including jointing with solvent, complete all as specified and as directed. |
| 52 | S&F PVC connections 15mm size with PTMT nuts 600mm long, completeall as specified and as directed. |
| 53 | S&F Health faucet (ABS body), brass chromium plated with 1.25m long flexible PVC tube and wall hook, suitable for 15mm bore dia pipe, complete all as specified and as directed. |
| 54 | S&F Vitreous china wash hand basin, white, of size 550mm x 440mm, with and including waste coupling and porcelain stopper, fixing brackets, cutting for and pinning in ends of brackets, 40mm dia CP brass waste fittings, complete all as specified and as directed. |
| 55 | S&F Tubular Towel rail 20mm dia, 600mm long, D type, Brass chromium plated, fixed with CP brass screws, wooden / plastic cleats, completed all as specified. |
| 56 | S&F PVC valveless, symphonic action type low level flushing cistern, 10 ltrs capacity, white with inlet ball valve, float and handle soft touch type including brackets, PVC flush pipe, fixed with CP brass screws, complete all as specified. |
| 57 | S&F Bib tap, 2 Way mixer Bib tap for mixing Hot & Cold water, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed. |
| 58 | S&F Unplasticised PVC (uPVC) pipe of 20mm bore of pipe of pressure rating 10 kgf/cm2 with and including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) and fixed to walls/ceilings/ laid in floors, including testing, complete all as specified and as directed. |
| 59 | S&F Unplasticised PVC (uPVC) pipe of 25mm bore of pipe of pressure rating 10 kgf/cm2 with and including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) and fixed to walls/ceilings/ laid in floors, including testing, complete all as specified and as directed. |
| 60 | S&F Stop Valve, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed. |
| 61 | S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends, suitable for iron pipe of 25mm bore, complete all as specified and as directed. |
| 62 | S&F 15mm bore chromium plated pillar taps, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed. |
| 63 | S&F Bib tap, chromium plated, quarter turn, fancy type, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed. |
| 64 | S&F 32mm bore Low density polyethylene (LDPE) waste pipe of pressure rating 6 kgf/sqcm, complete all as specified. |
| 65 | S&F Vitreous China half stall type urinals, white (excluding flushing cistern and flush pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including 32 mm dia PVC polythene waste pipe of suitable length from the urinal to trap of below, with and including urinals spreader of PTMT any colour for fixing with 15mm dia pipe min wt 600 gms including union and clamps, complete all as specified and directed by Engineer-In-Charge. |
| 66 | M&L for 150mm dia Reinforced Concrete Pipe NP2, with bends, collars tec., laid in trenches and jointed, with and including cement concrete bed PCC 1:3:6, type C2 (using 40mm graded granite stone aggregate), forming cradles, laid, packing & haunching sides, laid and tested, complete all as specified and as directed. |
| 67 | M&L for PCC 1:2:4 type B1 (using 20mm graded granite stone aggregate) as in surface channels and drains, complete all as specified and as directed. |
| 68 | M&L for Precast RCC (1:2:4), Type B-1, using 20 mm graded stone aggregate as in precast cover slabs, set in CM 1:4, complete all as specified and as directed. Note: Reinforcement shall be measured and paid separately. |
| 69 | M&L for Forming extra fair finished drain or channel of 25cm inner grith or width in cement concrete using extra cement with and including forming moulds / stopped ends etc., complete all as specified. |
| 70 | M&L for Cutting into existing manholes for connecting new drains of internal dia of pipe 150mm bore dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required, complete all as specified. |
| 71 | Excavating in post holes (or similar holes), as in hard/dense soil, each not exceeding 0.5cum, getting out , returning ,filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m where directed and making good surfaces, complete all as specified and as directed. |
| 72 | S&F Rolled mild steel work in tubular trusses, posts, including special shaped washer etc., complete using ERW or induction butt welded tubes conforming to IS-1161:1979 grade St-240, complete all as specified and as directed. |
| 73 | S&F Rolled mild steel roof trusses (framed) trussed purlins, rafters, struts (beam, tee, angle, channel, hollow sections or flat sections) including distance pieces & cleats, conforming tograde Fe 410-W Gde E-250 quality 'B', complete all as specified and as directed. |
| 74 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.45mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 75 | M&L for Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed. |
| 76 | S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.45mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 77 | S&F Mild Steel Corrugated Galvanised Steel Sheet 0.45mm thick of class 8, grade of zinc coating 120 grams /Square metre, as in roof covering with two corrugation side laps fixed with coach screws & washers, complete all as specified and as directed. |
| 78 | M&L for Cement concrete roofing tiles, rustic red / grey colour, 420mm x 330mm size of 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry as in roofing, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after. |
| 79 | M&L for Cement concrete Rusted Red/Grey colour Ridge cap of size 360mmx207mm x 240mm, with and including 15mm thick in roofing bedded and jointed in cement mortar 1:6, complete all as specified and as directed. |
| 80 | M&L for False ceiling with High Pressure Steam Cured (HPSC) 4mm thick Non Asbestos Fibre Cement ceiling boards fixed with and including supply & fixing powder coated aluminium snap grid of size 605mm x 605mm consisting of 25mm x 25mm x 1.25mm aluminium angles and TEEs of size 35mm x 25mm x 1.25mm with galvanised wire of required length and 2mm dia hanger grid suspended from trusses / ceiling and purlins not exceeding 1200mm c/c both ways, with and including applying three coats of white wash on ceiling surface, complete all as specified and as directed. |
| 81 | M&L for Concealed Point wiring with 1.5 Sq.mm FRLSH PVC insulated unsheathed copper conductor cable, single core multi stranded 1100Volt grade conforming to IS 694: 1977, drawn in and including PVC concealed rigid conduit (minimum 20mm) meadium grade ISI marked, with accessories, junction boxes, tees, terminal boxes with and including factory made metal flush boxes with modular top cover plates with frame for modular switches / sockets etc., including one run of 1.5 Sq.mm single core FRLS PVC unsheathed copper conductor cable as earth continuity conductor and connected to common earth dolly, for one light / fan /bell point controlled by one way switch, complete all as specified and as directed. Note: Cutting chases and making good surfaces shall be included in the unit rate. |
| 82 | All as per Serial Item No. 81 here-in-before but for 3 pin 5/6Amp switch socket point, on same board, complete all as specified. |
| 83 | All as per Serial Item No.81 here-in-before but for 3 pin 5/6Amp switch socket point, on independent board, complete all as specified. |
| 84 | All as per Serial Item No.81 here-in-before but with 2.5Sqmm copper conductor cable and 2.5 Sqmm cable as earth continuity conductor for 3 pin 6/16Amp switch socket point, on independent board, complete all as specified. |
| 85 | S&F Modular switch 1 way 5/6Amp, 1 Module, 240 Volts, complete all as specified and as directed. |
| 86 | S&F Modular Socket, 5/6A, 2/3 pin combined , 2 module, 240 Volts, complete all as specified and as directed. |
| 87 | S&F Modular switch 1 way 15/16A, 1 Module, 240 Volts, complete all as specified and as directed. |
| 88 | S&F Modular Socket, 6A/16A, 2/3 pin combined multipurpose, 2 module, 240 Volts, complete all as specified and as directed. |
| 89 | S&F Ceiling rose, 3 terminals PVC/Polycarbonate, isolated body, complete all as specified and as directed. |
| 90 | S&F LED Professional light fitting 1X20watt, surface mounted type, indoor aluminium extruded LED battens, high brightness LEDs 6000K, 220Volt, not less than 120 lum/W, PF>0.95, AC and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified. |
| 91 | S&F LED Professional light fitting 1X10watt, surface mounted type, indoor aluminium extruded LED battens, high brightness LEDs 6000K, 220Volt, not less than 120 lum/W, PF>0.95, AC and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified. |
| 92 | S&F LED Building Security light fitting 35/36Watts, 230 volts, die cast aluminium housing, not less than 120lum/W, with Suitable size GI bracket made out of 32mm GI light grade pipe fixed with clamps, nuts&bolts etc., with IP 65/66 protection with driver, bracket with impact, corrosion resistant and all accessories, complete all as specified and as directed. |
| 93 | M&L for Circuit / Sub main wiring with Two runs of 6.0 Sqmm PVC FRLSH insulated copper conductor cable, single core multi stranded 1100Volt along with one run of 6.0Sqmm as earth wire, drawn through and including rigid PVC conduit of suitable size (minimum 25mm dia), concealed type, medium grade as per IS 9537 (Part 1-1983) with conduit accessories, complete all as specified and as directed. Note: Two runs of cable, one run of earth wire and one run of conduit shall be measured as one unit. |
| 94 | S&F Exhaust fan, Metal Body with copper winding, AC single phase, 230Volt, 300mm sweep, 900RPM with blades, frame, louvers with all accessories and necessary fixing details, and connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed. |
| 95 | S&F Factory made epoxy powder coated Sheet metal enclosure Vertical TPN DB, 4 ways (VTPN MCB DB)with IP 43 protection, double door, sheet steel phosphetised powder painted with 200 amps rated copper busbar 415Volt, flush to wall, suitable for having MCCB’s/MCBs, complete all as specified and as directed. |
| 96 | S&F MCCB, 3pole, 125 Amps, 415Volts, thermal magnetic, Ics=100% Icu, 16kA current rating conforming to IEC-60947-II along with spreader incl Phase Barreir to be fixed in distribution board, complete all as specified. |
| 97 | S&F Factory made epoxy powder coated sheet metal enclosure for DBs (Fixed flush to the wall), SPN, 230 volt, 12Way, double door, IP-42 protection with 200 Amp rated copper bus bar 230Volt, suitable for having MCB’s, complete all as specified. |
| 98 | S&F MCB SPN 40Amp, 10kA, 230Volt, C curve with necessary connecting up in MCB DB, testing and commissioning, complete all as specified and as directed. |
| 99 | S&F MCB SP 10 to 32Amp, 10kA, 230Volt, C curve with necessary connecting up in MCB DB, testing and commissioning, complete all as specified and as directed. |
| 100 | S&F Galvanised steel water tubing 50mm bore dia, medium grade, conforming to IS:1239 (Part I) with and including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) and laid under trench / floors and including testing, complete all as specified and as directed. |
| 101 | S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends, suitable for iron pipe of 50mm bore, complete all as specified and as directed. |
| 102 | Supply, laying, testing and commissioning of LT XLPE insulated, screened with extruded PVC inner sheathed, PVC bedded, galvanised steel strip armoured electric FR power cable [heavy duty] of size 3.5core x 35.0Sqmm, with stranded aluminium conductor, 1100 volts grade, suitable for earthed system with and including cable glands, ferrules and connected accessories, laid in trenches or ducts or through the pipe etc., complete all as specified. Note: Necessary excavation & earth work & cable protection pipe shall be measured and paid separately under respective items. |
| 103 | Supply, laying, testing and commissioning of LT XLPE insulated, screened with extruded PVC inner sheathed, PVC bedded, galvanised steel strip armoured electric FR power cable [heavy duty] of size 4.0core x 16.0Sqmm, with stranded aluminium conductor, 1100 volts grade, suitable for earthed system with and including cable glands, ferrules and connected accessories, laid in trenches or ducts or through the pipe etc., complete all as specified. Note: Necessary excavation & earth work & cable protection pipe shall be measured and paid separately under respective items. |
| 104 | M&L for Double wall corrugated high density polymer (SDR 17) pipe of 63mm outer dia and 50mm inner dia, ISI marked, with and including necessary fittings like couplers, bends, end caps etc., laid in trenches /floors & fixed on wall/ pole with fittings such as bends, sockets & other connected accessories, complete all as specified and as directed. |
| 105 | S&F GI pipe light grade pipe 80mm dia for cable protection, complete on pole/walls/in road etc for cable protection, complete all as specified. |
| 106 | S&F Octagonal hot dip galvanized street light pole of 6 meter height, single arm with top dia minimum 70mm, bottom dia minimum 135mm, made with 3mm thick GI sheet, anchor plate & base plate of size 225mm X 225mm X 16mm fixed with 04 Nos of M20 size foundation bolt of minimum length 750mm, internal & external fabrication of the pole shall be in accordance with IS-2629/BSEN ISO 1461, with and including wiring of pole from junction box to street light and all necessary civil works i.e earthwork, RCC/PCC foundation as per manufacturers design, complete all as specified and directed. Note: The contractor shall submit and approve the foundation drawing issued by the manufacturer before starting the work. |
| 107 | S&F new generation energy saving and environmental friendly long life LED street light made up of innovative die cast aluminium housing high power LED as lighting source with IP-65 power consumption 70/72watt with minimum 120lum/watt, complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) including pvc coated twisted copper cable 1.5 sqmm x 3 core through copper connectors from junction box to security lights, complete all as specified and directed. |
| 108 | S&F IN REPAIR LT Panel as per IEC 61439, Outdoor type, floor mounted free standing dust and vermin proof panel / DB with IP-54 protection, CPRI approved OEM, frame fabricated out of 40mmx40mm x 4mm MS angle iron, made with 3.15mm thick CRCA sheet for entire outer panel and for inner compartments with separate cubicle chamber with cable alley with minimum 300mm width for installation/connecting switchgears with the main bus bar using aluminium bus link or copper conductor flexible wires suitable for switch rating and connecting outgoing terminals of the switchgear with terminal blocks of appropriate current rating using flexible copper wires duly terminated by cable lugs and thimbles, MS surfaces epoxy based powder coated, shade as approved over 2 coats of red oxide primer, surfaces pre-treated in seven tank process for de-greasing, de-rusting & Phosphated, panel having front and rear opening and provision for installation of separate cable alleys, all MCCBs must be have thermal magnetic relrase, busbar chamber and switchgear compartments, provision in cable alleys for bottom cable entry for incoming & outgoing cables, fixing danger notice plate, with and including erection, testing and commissioning, complete all as specified and directed including the following fixtures and fitments:- |
| 109 | (a) Aluminium bus bar four strips 400Amp, 415 volts, rating with epoxy insulator heat shrink colour code for 415Volt, 50Hz, 3 phase, 4 wire system with internal wiring size not less than 2.5Sqmm FRLS copper wire with ferouls - 01 Set. (b) Incoming:- (i) MCCB 04 Pole, 250Amp with ultimate breaking capacity Icu- 36KA at 415 volts, adjustable type with thermal and magnetic settings conforming to IEC 60947 Part-I/IS-13947 Part-I -01 No (Ics=Icu=100%) (ii) Digital Multifunction Meter with V, A, KWH, KVA, PF - 01Nos (iii) LED Indication lamps R,Y,B 3 phase –01set (c) Outgoing:-(i) MCCB 04 Pole, 100Amp with ultimate breaking capacity Icu- 25KA at 415 volts, adjustable type with thermal and magnetic settings conforming to IEC 60947 Part-I/IS-13947 Part-I - 01 No (Ics=Icu=100%) (ii) Digital Multifunction Meter with V, A, KWH, KVA, PF - 04Nos (iii) Street Light Timer 3KW - 01No (iv) LED Indication lamps R,Y,B 3 phase – 05sets, (v) Spare for MCCB 4P 100Amp - 01Nos (vi) Internal wiring with suitable size of PVC insulated stranded copper conductor cable duly crimped with copper lugs & ferruled and aluminum strips for MCCB's. Note :- Panel drawings & make of MCCB/SDFU will be submitted by contractor for approval of GE before ordering the panel. |
| 110 | M&L for Earthing complete with galvanised steel earth plate electrode 60cm X 60cm X 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead 4mm GI wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of SSR Part-I, including excavation / earth work in any strata, adequate quantity of charcoal and common salt, PCC chamber with RCC 1:2:4 type B1 40mm thick cover slab with 8mm dia TMT bars @150mm c/c in bothways, suitable handle and angle iron frame of suitable size to fix the cover, with 20mm bore GI pipe light grade for watering with funnel, wire mesh and 15mm bore GI pipe medium grade for GI wire protection and 4mm GI earth wire, including testing after completion, complete all as specified and directed. Note : Earth wire will be measured after 7.5mtr from the earth strip or earth testing terminal block whichever is lesser under relevant item. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysSep 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender