Tender For Road Development Work Of Road From Ka Road Near Kulai Baazar To Ka Road At Basudebpara Via Harinmara (Length=4.00 Km)/ Sh:- Protection Work Of Road By Reinforced Cement Concrete Retaining Wall, Cement Concrete Block, Drain Etc From Chainag
Tender Value
1.07 Crore
Estimated cost
Bid Submission
31 Aug 2026
5 days left
EMD
2.15 Lakhs
Bank guarantee accepted
Document Fee
4000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhalai → Tripura
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Road Development Work Of Road From Ka Road Near Kulai Baazar To Ka Road At Basudebpara Via Harinmara (Length=4.00 Km)/ Sh:- Protection Work Of Road By Reinforced Cement Concrete Retaining Wall, Cement Concrete Block, Drain Etc From Chainage 2.10 Km To 4.00 Km.
BOQ
| Sl. No. | Item Description |
| 1 | ii)Compacting orginal ground supporting Subgrade. Loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 for subgrade construction as per MoRD Technical Specification Clause 303.5.2. |
| 2 | Excavation in Soil with Hydraulic excavator and tipper with disposal upto 1000 m. Excavation for road work in soil with Hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tipper, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections and transporting to the embankment location with all lifts and leads upto 1000m as per MoRD Technical Specification Clause 302.3. |
| 3 | Construction of Embankment with Material obtained from borrow pits Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with lift upto 1.5m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRD Technical Specification clauses 301.5 |
| 4 | Construction of Subgrade and Earthen Shoulders Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site , spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per MoRD Technical Specification Clause 303.1. |
| 5 | Excavation for Structures (A) Without dewatering Earthwork in excavation for structures as per drawing and MoRD technical specifications Clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleterious material and disposal upto a lead of 50 m, dressing of sides & bottom and backfilling in trenches with excavated suitable material. I.Ordinary soil (i)Upto 3 m depth |
| 6 | Filling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200. (i)Sand filling |
| 7 | Providing concrete for plain concrete (using jhama brick aggregate) in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement)I.P.C.C grade M 10 ( Using Jhama Brick Aggregate ) (i)Nominal mix 1:3:6 |
| 8 | Plain/reinforced cement concrete in foundation complete including formwork as per drawings & MoRD technical specification Clauses 802, 804, 805, 806, 807, 900, 1202 & 1204. (including centering, shuttering, staging etc. but excluding reinforcement) (VI) RCC grade m25 (i)Upto 5m height |
| 9 | Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar in foundation complete as per drawings & MoRD technical specification Clauses 1002, 1005, 1010 and 1202. |
| 10 | Plain/reinforced cement concrete in sub structure complete including formwork as per drawings & MoRD technical specification Clauses 802, 804, 805, 806, 807, 900, 1202 & 1204. (including centering, shuttering, staging etc. but excluding reinforcement) (VI) RCC grade m25 (i)Upto 5m height |
| 11 | Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar in substructure complete as per drawings & MoRD technical specification Clauses 1002, 1005, 1010 and 1202. |
| 12 | Providing weepholes in brick masonry/ stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe or uPVC pipe (110 mm OD of 6.0 Kg/cm2 pressure) extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MoRD technical specification clauses 614, 709, 1204.3.7. |
| 13 | Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8. |
| 14 | Surface Drain Construction of unlined surface drains of average cross-sectional area 0.40 sqm in ordinary soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3 m and lead of 50 m (average lead 25 m) as per MoRD Technical Specification Clause 307. (I)Surface Drains in Ordinary Soil (A)Manual Means |
| 15 | Construction of road side pucca drain with M10 (1:3:6 with jhama brick aggregate) to specified lines, grades, levels and dimensions as per approved design and MoRD Technical Specification Clause 307, 1606. Excavated material to be used in embankment at site. (including centering, shuttering, etc. but excluding reinforcement) D.U shaped drain with ( top clear width 600 mm, bottom clear width 600 mm and clear depth of 600 mm) (I)In Ordinary Soil |
| 16 | Brick solingFlat brick solingProviding and laying flat brick soling layer on prepared subgrade according to lines, grades and cross-section shown on the drawing, filling joints with Earth, free from clay with a Plasticity Index not exceeding 6, watering and rolling the same with three wheeled road roller 80-100 kN as per MoRD Technical Specification Clause 412. |
| 17 | Brick edging laid in full brick widthProviding and laying brick edging on prepared subgrade according to lines, grades and cross-section shown on the drawing, filling joints with Earth, free from clay with a Plasticity Index not exceeding 6, watering and rolling the same with three wheeled road roller 80-100 KN as per MoRD Technical Specification Clause 412. |
| 18 | WBM Grading 2 Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per MoRD Technical Specification Clause 405. (A)By Manual Means |
| 19 | WBM Grading 3 Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming, binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per MoRD Technical Specification Clause 405. (A)By Manual Means |
| 20 | Prime Coat (ii ) Medium Porosity Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.20 kg/sqm using mechanical means as per MoRD Technical Specification Clause 502. |
| 21 | Tack coat iii)Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface treated with primer & cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503. |
| 22 | Tack coat iii)Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the dry and hungry bitumen surface cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503. |
| 23 | 25 mm thick Open-Graded Premix Carpet using Bituminous(Viscosity grade/ modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 25 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using Viscosity grade bitumen or emulsion to required line, grade and level to serve aswearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 508.Case - II By Mechanical Means (I)Bitumen of VG-30 |
| 24 | Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 510.A.By Manual Means Case - II : Type - B I.Bitumen of VG-30 |
| 25 | Brick masonry work in cement mortar in substructure complete excepting pointing & plastering, as per drawing & MoRD technical specification Clauses 602, 603, 604, 1202 and 1204. II.In 1:4 cement mortar |
| 26 | Providing and laying of apron with cement concrete blocks of size as per Table 1300.1 cast-in-situ and made with nominal mix of M-15 grade cement concrete (using jhama brick aggregate)as per drawing and MoRD technical specification Clause 1301 (rate includes preparation of bed, nominal surface reinforcement and filling of granular material in recesses between blocks). |
| 27 | Plastering with cement mortar (1:4) 12 mm thick on brickwork / C.C. work including a finishing coat of neat cement punning with 2.75 Kg of cement per sqm in substructure as per MoRD technical specification Clauses 613.4 & 1204 |
| 28 | Excavating trenches of required width for pipes, cables etc. including exacavation for sockets, dressing of sides where required, ramming of bottoms, depth upto 1500 mm (slope-1 in 200)including getting out the excavated soil and backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil with all required leads as per Chapter - 2 of CPWD specification and direction of the Engineer - in - charge.A) For UPVC pipes in new work.a) In all kinds of soil. i)For pipes not exceeding 90 mm dia |
| 29 | Excavating trenches of required width for pipes, cables etc. including exacavation for sockets, dressing of sides where required, ramming of bottoms, depth upto 1500 mm (slope-1 in 200)including getting out the excavated soil and backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil with all required leads as per Chapter - 2 of CPWD specification and direction of the Engineer - in - charge.A) For UPVC pipes in new work.a) In all kinds of soil. ii) For pipes exceeding 90mm dia. but not exceeding 300mm dia. |
| 30 | Providing, fixing and laying rigid UPVC pipes conforming to IS : 4985 jointing with couplers, of same class conforming to IS : 10124 ( Pt-II ) with solvent cement conforming to IS : 14182 including testing of joints complete ( but excluding the cost of specials like bend, tees etc. which will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge A. Class - 3 ( working pressure 6.0 kg / cm2) i) 90 mm OD |
| 31 | Providing, fixing and laying rigid UPVC pipes conforming to IS : 4985 jointing with couplers, of same class conforming to IS : 10124 ( Pt-II ) with solvent cement conforming to IS : 14182 including testing of joints complete ( but excluding the cost of specials like bend, tees etc. which will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge A. Class - 3 ( working pressure 6.0 kg / cm2) ii) 110 mm OD |
| 32 | Providing, fixing and laying rigid UPVC pipes conforming to IS : 4985 jointing with couplers, of same class conforming to IS : 10124 ( Pt-II ) with solvent cement conforming to IS : 14182 including testing of joints complete ( but excluding the cost of specials like bend, tees etc. which will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge A. Class - 3 ( working pressure 6.0 kg / cm2) iii) 140 mm OD |
| 33 | Providing and laying of flexible PVC pipe (conforming to IS:7634) complete including earth work as per specification and direction of the Engineer - in - charge (cost of fittings will be paid separately). i. 15mm dia |
| 34 | Providing, fixing and laying fabricated UPVC end cap conforming to IS : 10124 ( Part 4 ) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. i) 90 mm dia. |
| 35 | Providing, fixing and laying fabricated UPVC equal tee conforming to IS:10124 (Part 5) with solvent cement conforming to IS :b 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge. i) 90 x 90 mm dia. |
| 36 | Providing, fixing and laying fabricated UPVC equal tee conforming to IS:10124 (Part 5) with solvent cement conforming to IS :b 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge. ii) 110 x 110 mm dia. |
| 37 | Providing, fixing and laying fabricated UPVC equal tee conforming to IS:10124 (Part 5) with solvent cement conforming to IS :b 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge. iii) 140 x 140 mm dia. |
| 38 | Providing, fixing and laying fabricated UPVC straight reducer conforming to IS : 10124 (Part 3) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge.i) 110 x 90 mm dia. |
| 39 | Providing, fixing and laying fabricated UPVC straight reducer conforming to IS : 10124 (Part 3) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge.ii) 140 x 110 mm dia. |
| 40 | Providing, fixing and laying fabricated UPVC bend of required degree conforming to IS:10124 (part 8/9/10/11/12/13) with solvent cement conforming to IS: 14182 including testing of joints complete as per CPWD specification and direction of the Engineer- In Charge.i) 90 mm dia. |
| 41 | Providing, fixing and laying fabricated UPVC bend of required degree conforming to IS:10124 (part 8/9/10/11/12/13) with solvent cement conforming to IS: 14182 including testing of joints complete as per CPWD specification and direction of the Engineer- In Charge.ii) 110 mm dia. |
| 42 | Providing, fixing and laying fabricated UPVC bend of required degree conforming to IS:10124 (part 8/9/10/11/12/13) with solvent cement conforming to IS: 14182 including testing of joints complete as per CPWD specification and direction of the Engineer- In Charge.iii) 140 mm dia. |
| 43 | Making road crossing by horizontal boring for smooth laying of UPVC / Cl/ DI / GI pipes etc. of required dia complete as per specification and the direction of the Engineer-in-charge. i. By mechanical means |
| 44 | Providing & fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) as per CPWD specification and direction of the Engineer - in - charge i) 80 mm dia. PN-1.6 |
| 45 | Providing & fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) as per CPWD specification and direction of the Engineer - in - charge ii) 100 mm dia. PN-1.6 |
| 46 | Providing & fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) as per CPWD specification and direction of the Engineer - in - charge iii) 125 mm dia. PN-1.6 |
| 47 | Providing, fixing and laying flanged fabricated UPVC tailpiece conforming to IS : 10124 (Part 6) with G.I. flange (8 mm thick) with solvent cement conforming to IS – 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge.i) 90 mm dia. |
| 48 | Providing, fixing and laying flanged fabricated UPVC tailpiece conforming to IS : 10124 (Part 6) with G.I. flange (8 mm thick) with solvent cement conforming to IS – 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge.ii) 110 mm dia. |
| 49 | Providing, fixing and laying flanged fabricated UPVC tailpiece conforming to IS : 10124 (Part 6) with G.I. flange (8 mm thick) with solvent cement conforming to IS – 14182 including testing of joints complete as per CPWD specification and direction of the Engineer-in-charge.iii) 140 mm dia. |
| 50 | Providing and fixing brass ferrule with C.I. cover conforming to IS : 2692 including boring and tapping the main as per CPWD specification and direction of the Engineer - in - charge.a) 10 mm nominal bore |
| 51 | Providing and fixing G.I. union as per CPWD specification and direction of the Engineer - in - charge.i) 15 mm dia |
| 52 | Providing & fixing UPVC Service Saddle as per CPWD Specification and direction of the Engineer-in-charge.i. 140 mm dia with 15 mm dia opening |
| 53 | Providing & fixing UPVC Service Saddle as per CPWD Specification and direction of the Engineer-in-charge.ii. 110 mm dia with 15 mm dia opening |
| 54 | Providing & fixing UPVC Service Saddle as per CPWD Specification and direction of the Engineer-in-charge.iii. 90 mm dia with 15 mm dia opening Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender