Tender For Repair / Replacement Sunken Flooring, Vertical Stacks, Plumbing, Sanitary Fiittings, Plastering, Flooring/Tiling, Plinth Protection, Wooden/Aluminium Joinery, And Other Misc Work At Iam And Vayu Vihar C Under Ge (Af) Marathahalli
Tender Value
32 Lakhs
Estimated cost
Bid Submission
11 Sep 2026
17 days left
EMD
64000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bengaluru Urban → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Repair / Replacement Sunken Flooring, Vertical Stacks, Plumbing, Sanitary Fiittings, Plastering, Flooring/Tiling, Plinth Protection, Wooden/Aluminium Joinery, And Other Misc Work At Iam And Vayu Vihar C Under Ge (Af) Marathahalli
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames with shutters not exc. 1.5 sq. m Each (without taking off shutters from the frames) complete all as specified and as directed. |
| 2 | Taking down chowkhats or frames with shutters exceeding 1.5 Sq.m and not exc. 4 Sq. m Each (without taking off shutters from the frames) complete all as specified and as directed. |
| 3 | Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied & fixed |
| 4 | Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied & fixed |
| 5 | M & L for providing cement concrete 1:3:6, type C0, using 12.50 mm graded stone aggregates as in bed blocks, filling concrete for chowkats steel frames etc complete all as specified and as directed . |
| 6 | S & F 30 mm thick Flush shutters , solid core construction, with block board core and plywood face panels one face is covered with decorative face veneer with lipping/ frame to match fixed to chowkats complete all as specified and directed. |
| 7 | S & F 2 nd class hard wood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed. Note :- wire mesh shall be measured and paid separately in respective item. |
| 8 | S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete. |
| 9 | S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed |
| 10 | S & F 100 mm size butt hinges medium weight, cold rolled mild steel complete all as specified and directed. |
| 11 | S & F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete . |
| 12 | S & F aluminium 200 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete. |
| 13 | S & F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete. |
| 14 | S & F 150 mm size aluminium handles cast type, anodised ISI marked complete |
| 15 | Demolition of unreinforced cement concrete of any description and in any position not otherwise specified for complete all as specified and directed. |
| 16 | M & L 25 mm thick PCC (1:2:4) using 12.50 mm graded aggregate laying under bottom of the sunken floor finished even and smooth dcomplete all as specified and directed . |
| 17 | M & L cement concrete 1:5:10 with brick coarse aggregate as in filling in sunk floors complete all as directed . |
| 18 | M & L treatment for sunken portion with and including 10mm thick cement plaster in CM 1:3 mixed with liquid WPC @ 200ml per bag of cement when concrete surface is green. Over after dry of plaster surface laying water proofing treatment to the slab area with Home shield PU elastroseal AR single componenr liquid applied cold allied, moisture cured high tensile elastromatic PU water proofing membrane @ 1.5 kg per Sqm in 2 coats to achive final DFT of 1.3 to 1.5 mm DFT including prime coat of HS PU Elstroprime @ 8-10 sqm per Ltr of same material Coat emultion over coat of complete all as specified and directed (Note : WPC shall be measured and paid in supply only item) |
| 19 | Supply only Liquid water proofing compound |
| 20 | M & L 32 mm dia CPVC pipe as in spout pipe medium grade 32mm bore including of required shape all as specified and directed. |
| 21 | S&F powder coated Aluminium section for door frame , windows, ventilators, with one or more rebates, including joining cleats for fixing necessary lugs complete frame work complete all as specified. |
| 22 | S&F powder coated Aluminium section for door shutters aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, powder coated aluminium shap beading screws etx complete all as specified |
| 23 | S & F powder coated Aluminium section for window and ventilator sliding/fixed type without sash aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium shap beading screws, powder coated aluminium fittings such as peg stays 150 mm long ( 1 Nos) hinges type B-21 100 mm long (2 Nos) suitable handle 1 Nos complete all as specified |
| 24 | S & F powder coated Aluminium grill for window / ventilators of mesh size 100 x 100 mm and made out of 6 mm thick aluminium power coated sections including necessary fitting arrangements all as specified and directed |
| 25 | S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples all as specified and as directed |
| 26 | Supply only 4 mm thick (nominal) Sheet glass , ordinary quality , in squares, not exceeding 0.50 sqm each pane fixed with beads ( supplied with joinery ) complete all as specified. |
| 27 | Supply only 4 mm thick (nominal) Sheet glass , ordinary quality , in squares, exceeding 0.50 sqm each pane fixed with beads ( supplied with joinery ) complete all as specified. |
| 28 | S & F in repairs150mm length floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor complete all as specified and as directed |
| 29 | S & F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete. |
| 30 | M & L Preparation of New wood or previously untreated surfaces of any description , not otherwise description, over 10 cm width or grith apply two coat of synthetic enemel paint (ordinary tint) over a coat of pink primer complete all as specifed and directed. |
| 31 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above GL) all as specified and directed. |
| 32 | M & L for PCC 1:2:4 type B1 using 20mm graded aggregate 40mm thick as in sub base or levelling course etc complete all as specified and directed. |
| 33 | M & L for Double Charged Vitrified Ceramic Colour tiles 9 to 10 mm thick light shade(Square / Rectangular) polished , area of each tiles exceeding 0.36 Sqm but not exceeding 0.42 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles over and including cement screed or bedding layer of cement mortar 15mm thick in 1:4 complete all as specified and as directed . Make : Somany, Johnson, AGL, Kajaria |
| 34 | All as per item No. 33 above but as in skirting over cement mortar backing plaster in CM1:3 10 mm thick including dismantling of wall tiling of any thickness ncluding cement mortar bedding ( but not backing) removing tiles and rubbish off the premises.complete all as specified and directed. Make : Somany, Johnson, AGL, Kajaria |
| 35 | Dismantling of floor , hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permises compete all as specified and directed. |
| 36 | M&L non skid / anti skid ceramic tiles coloured pattern as required of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including laid over 15mm thick screed bed in CM (1:4) compete all as specified and directed |
| 37 | M&L glazed ceramic coloured, designer & pattern (dark & light shade combination) tiles in 350x250x7 or 450x350x7 or 450 x 300 x 7-8 mm thick on vertical surfaces such as dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over with and including 10 mm thick backing coat in CM 1:3 and dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 38 | Demolition of Stone slabs and tiles laid dry or laid dry and pointed of any description or thickness in floors, aprons etc. |
| 39 | M&L for Machine cut kota stone slab flooring 20-25mm thick of size not less than .034 Sqm of each slab over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with and including 20mm thick screed bed or bedding in cement mortar 1:4 complete all as specified and directed . |
| 40 | M&L for Kota stone slab 20-25 mm thick in riser of bricks steps & riser of staircase , skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing with & including backing coat in 10 mm thick CM (1:4) to receive Kota Stone complete all as specified and directed |
| 41 | M&L Granite (of any type) tiles, 18-20 mm thick machine cut laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including cutting and polishing with and including 20mm thick screed bed or bedding in cement mortar 1:4 complete all as specified and directed |
| 42 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed |
| 43 | Demolition of unreinforced cement concrete in ground floors etc and paving n. exc 15cm thickness (below or above ground level) complete all as specified and directed |
| 44 | M & L 75 mm thick plinth protection of Cement concrete 1:3:6 type C-2 (using 40mm graded agg) all as specified and directed. |
| 45 | M&L for 25mm thick (1:2:4) Type-B-1 (using 20mm graded crushed stone aggregate) as in level course of flooring complete all as specified and directed . |
| 46 | M & L vitrified ceramic tiles coloured pattern as required 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matches with and including laid over 15 mm thick screed bed in CM 1:4 compete all as specified and directed . |
| 47 | All as per item No. 46 above but on skirting over 10 mm thick backing coat in CM 1:3 including dismantling of tiles complete all as specified and directed . |
| 48 | M & L heavy duty pavement tiles of size 400 mm x 400 mm x 12 mm /300 mm x 300 mm x 12 mm thick for out door spaces any colour/pattren of (acid skid , anti bactireal , stain resistance & scratch resistant, tiles) set jointed and pointed in chemical laid over 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 49 | Dismantling structural steel work including doors, gates but excluding framed truss etc.. complete all as specified and directed . |
| 50 | S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410-W(Gde-E- 250) quality-A complete all as specified and directed. |
| 51 | M & L for preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over of redoxide zinc chrome coat complete all as specified and as directed. |
| 52 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws complete with and including dismantling corrugated steel sheeting, any gauge, thickness, including nainital or similar roof coverings complete all as specified and directed.completed all as specified and directed |
| 53 | S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws as in ridge,eaves boards, hips, velly gutter drip and straight flushing of reuired machine moulded shape and size complete with and including dismantling plain steel sheeting, any gauge, thickness, including nainital or similar roof coverings and eaves boards of any description complete all as specified and directed.completed all as specified and directed |
| 54 | S & F in repairs of armstrong ceiling system complete with 12 mm thick ceiling boards ( 84% light reflectence ) and powder coated GI frame work with section not less than 0.7 mm thick all as per manufure instructions all as specified and directed. |
| 55 | S & F in repairs of armstrong ceiling board 12 mm thick ( 84% light reflectence all as specified and directed. |
| 56 | S & F in repairs 12 mm thick Perforated particle board/tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed with nails to timber/ Aluminium framework or with staples on snap grid complete all as specifie and directed. |
| 57 | S&F 18/19 mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice amination & other side balancing white lamination, fixed with screws to timber frame work® and including dismantling boarding, any description , fixed in any position with nails complete all as specified and directed |
| 58 | M & L in repairs for second class hardwood plain fillets in square, rectangular or triangular in section, clean sawn, secured with nails or borads n exc 3 Sq.cm with complete all as specified and directed. |
| 59 | S & F Stainless steel hadles size 100 mm Fixed with SS screws complete all as specified and directed. |
| 60 | S & F Stainless steel magnetic catches fixed with SS screwes complete all as specified and directed. |
| 61 | M&L for complete removal of existing treatment of any layer and applying one or more coats of french polish of requrired tint complete all as specified and directed . |
| 62 | M&L rendering 15 mm thick in CM 1:6 on brick/concrete/stone wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete with and including taking down cement or lime plaster of any description from stone /brick/concrete wall etc incl raking out joints hacking for key scrurbbing down with water and disposing of the rubbish complete all as specified and directed by Engr-in-Charge. |
| 63 | M&L for Pre-cast cement concrete block masonry type C1 1:3:6 (20 mm graded aggregate) with solid blocks, exc.10cm in width and setting in mortar including demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed complete in CM 1:6 all as specified and directed. |
| 64 | M&L rendering 15 mm thick in CM 1:4 on brick/concrete/stone wall surfaces of any description, and finishing the surfaces even and fair without using extra cement, complete all as specified and directed by Engr-in-Charge. |
| 65 | M&L rendering 15 mm thick in CM 1:6 on brick/concrete/stone wall surfaces of any description and other surface and finishing the surfaces even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. |
| 66 | M&L for preparing new plastered or unplastered surfaces on walls & other surface and applying two coats of oil emulsion distemper over a coat of 3 mm wall care putty with rubbing or smoothing of surface upto ture finish over a coat of water base primer complete all as specified and directed by Engr-in-Charge. |
| 67 | M&L for preparation of new plastered wall surfaces and applying two coat of cement based paint on walls over a coat of primer with alkali resistant priming paint complete all as spd and directed. |
| 68 | S&F in repair 15 mm aerated bib tap ( fancy type) , cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed including taking down old one. |
| 69 | S&F in repair brass Chromium plated shower roses of size 125mm with or without swivel joints, any size, including fixing to steel pipe or unionincluding taking down old one. |
| 70 | S&F in repair CP angle valves (half turn type)/ conclead type (chromium plated fancy type) 15 mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handles, screwed both end for iron pipe or for unions complete all as specified and directed including taking down old one. |
| 71 | S &F in repair 15 mm dia aerated CP wall Mixer for mixing hot & cold water screwed down for iron pipe Central Hole r without Pop-up waste system complete all as specified and directed. |
| 72 | S&F in repair 15 mm dia aerated swan neck sink / wash basin piller tap water screwed down for iron pipe complete all as specified and directed. |
| 73 | S&F in repair Vitreous china wash hand basin, white, flat back of size 630 x 450 mm white excluding taps, waste, chain and plug and porcelain stopper but including bracket, cutting for and pinning the ends of brackets including PTMT waste coupling 32 mm dia as suitable complete all as specified and directed by the Engr-in-Charge. |
| 74 | S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and directed by Engr-in-Charge. |
| 75 | S&F in repairs PTMT grating dome 100 mm dia (minimum weight 25 gms) complete all as specified and directed including taking out old one. |
| 76 | M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed |
| 77 | S & F in repairs 20 mm CPVC Pipe SDR 11 & Plain CPVC SDR 11 Fittings such as Tee, Elbow, nipple and small piece of pipe in trenches or fixed to wall/Ceiling complete all as specified and as directed |
| 78 | All as per Item No 77 above but 25 mm dia bore |
| 79 | Hacking out old broken glass pane (any thickness , size, quality or description) from steel frame glazed with putty or fixed with beads. |
| 80 | M & L for 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane. |
| 81 | M & L for 4 mm thick figured glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane. |
| 82 | S & F in repairs Galvnised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, wooden beads or galvanised wire staples etc complete all as specified and directed. |
| 83 | S&F in repairs 25 mm dia anodised aluminium anodised powder coated tubular curtains rod including fixing brackets complete all as specified and directed. |
| 84 | S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white with P or S trap with and including plastic water closet seat cover , connection to trap, flushing pipe & anti -syphonage pipe etc including necessary materials for fittings & making good to floor complete all as specified and directed by Engr-in-Charge.. |
| 85 | S&F in repair vitreous China, squatting pan, Orissa Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with CI trap of suitable size ( P or S type) including connection to trap and to flushing pipe, anti syphonic pipe etc complete all as specified and directed . |
| 86 | S&F in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as required and as directed. |
| 87 | S&F in repair 15 mm dia PVC connections, 600 mm long with PTMT nuts of suitable size at two end complete all as specified and directed including taking out old one. |
| 88 | S & F in repairs 25 mm dia ball valve complete all as specified and directed. |
| 89 | S & F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty including taking down of onld one and fixed . complete all as specified and directed. |
| 90 | S & F in repair aluminium( Extruded section) body door closer hydraulically regulated , designation No. 3 universal type , suitable for door shutterof 851 to 1000mm in width complete all as specified and directed. Make : Dyna and equivalent ISI marked |
| 91 | S & F in repairs 110mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall complete all as specified and directed |
| 92 | S & F in repairs 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall complete all as specified and directed |
| 93 | S & F in repairs 110 mm dia PVC (SWR) bends of any radius with access door complete all as specified and directed |
| 94 | S & F in repairs 75 mm dia PVC (SWR) bends of any radius with duck foot or heel rest fitted with oval access door complete all as specified and directed. |
| 95 | S & F in repairs 75 mm dia PVC (SWR) junction ingle, (Single T) equal or unequal with access door complete all as specified and directed. |
| 96 | S & F in repairs 110 mm dia PVC (SWR) junction ingle, (Single T) equal or unequal with access door complete all as specified and directed. |
| 97 | Cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc of capacity exc 500 ltr but n exc 1000 ltr complete all as specified and directed. |
| 98 | S & F 1000 Ltrs Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position including dismantling of water tanks exc 500 & n exc 1000 capacity ,all as specified in SSR Part I Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysSep 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender