Tender For Special Repair To Roof For Repalcement Of Asbestos Sheet With Galvalume Sheet And Certain Misc Works At Bldg No P-34 B Veh Mr Bay Of Asw Under Ge(N) Ahilyanagar.
Tender Value
43.68 Lakhs
Estimated cost
Bid Submission
14 Sep 2026
12 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ahmednagar → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Roof For Repalcement Of Asbestos Sheet With Galvalume Sheet And Certain Misc Works At Bldg No P-34 B Veh Mr Bay Of Asw Under Ge(N) Ahilyanagar.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, including ridge & removing all rubbish/ dismantled material outside MD Land. all as directed. |
| 2 | Dismantling structural steel work including doors,gates but excluding framed truss etc. |
| 3 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including removal out of MD land (measured overall as fixed along the centre line over fittings and accessories) |
| 4 | Providing and erecting two legged metal tubular scaffolding (cup lock type) of width 1200 to 1500mm largely free standing using H frames of tubular pipes of minimum 40mm diameter, with base plates fixed or adjustable with necessary clamps, coulders, brackets for projections, joint pins, pulleys and other accessories including steel angle or tubular pipe bracings at adequate intervals, access platforms of metal or timber planks of span not exceeding 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work including provision of rubber inserts to pipe ends at point of contact with structure to avoid damage, including access ladders with intermidiate platforms. the scaffolding to be suitably braced and anchored to to the building using support systems created temporarily at the opening in walls using vertical and horizontal adjustable propson the exterior/interior side of building structure, 15 metre & more height, above ground level . The rate includes provision of high density plastic sheets covering to protect architectural details on the entire building face a nylon net to prevent all debris falling onto the pavement required and the safety platform at ground level coevering the pedestrain walkways. etc. complete. (The Floor area of the scaffolding shall be measured for payment purpose. The payment will be made once only for execution of all items for such works. |
| 5 | S&F Pre-painted Galvalume sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc. complete all as specified and directed by Engg-in-charge. |
| 6 | Supply and fix Pre-painted 0.50 mm thick plain, galvanised sheet in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engineer-in-charge. |
| 7 | M&L for 1.00mm thick Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) completely with welding and soldering as required to maintian the size and shape of gutter as per length of shed all as specified and as directed by Engineer-in-Charge. |
| 8 | Fixing only 1.00mm thick Plain, black, mild steel sheeting, in ridges,hips, valley gutters, drip and straight flashings (length and girth as fixed) completely with welding and soldering as required to maintian the size and shape of gutter as per length of shed all as specified and as directed by Engineer in Charge |
| 9 | M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165. |
| 10 | S & F Aluminium wind ties (40x3) mm for roof including securing bolts; as directed, drilling holes,notching for wire, etc.;including all necessary drilling, bolting or riveting, etc.,and similar work complete all as specified and directed by Engg-In-Charge. |
| 11 | S&F 24\\"x31\\" Roof top Ventilator having Vents made from 0.5 mm Hindalco make Aluminium Alloy, Top made from Stainless Steel, Bottom ring made from 0.5 mm Stainless Steel, Bearing less Cylindrical Assembly manufactured from M.S. Seamless Pipe with Zinc Coating complete all as specified and directed by Engg-in-Charge. |
| 12 | S&F Rolled sections as in main and purlins where connected to common rafter and running rails and guides for sliding doors:fixed with angle cleats or other connecting plates |
| 13 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer for new steel surfaces of any description exc 10 cm width or girth including preparation of surfaces all as directed. |
| 14 | M&L for 1.25mm thick Plain black, mild steel sheeting for Head Hopper type Square type, Flat or Corner Type adequate for 150mm dia Rainwater downtake pipes etc. |
| 15 | S&F 160mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or Pillars etc. |
| 16 | S&F 160mm PVC (SWR) 45 degree Shoe bend with rubber ring joints fixed to walls Or Pillars etc. |
| 17 | M&L for Preparation of old steel and iron surfaces, of any description, over 10 cm width or girth not other wise described and applying one coats of synthetic enamel paint over a coat of red oxide primer. |
| 18 | M&L for preparation of old plastered or unplastered surface of walls including cornices etc by brooming down or steel wire brushing scraping down smook soot, moulds, moss and efflorescent salt, trading oil and greasy spots and apply two coats of white lime wash at any height including scaffholding etc complete all as specified and directed by Engineer-in-charge.. |
| 19 | Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water complete all as directed by Engineer-in-Charge. |
| 20 | M&L for rendering, 15 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and fair without using extra cement all as specified and directed. |
| 21 | M&L for rendering, 12 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and fair without using extra cement all as specified and directed. |
| 22 | M&L for preparation of newly plastered surface of wall and apply two coats of cement based paint over a coat of alkali primer any height including scaffolding etc complete all as directed. |
| 23 | M&L for preparation of newly plastered surface of wall and apply two coats of OBD over a coat of primer any height including scaffolding etc complete all as directed. |
| 24 | S&F in repairs Steel rolling shutters, of 1.25 mm thick without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete; push pull or manual type. |
| 25 | .-ditto- all as ser item No 24 above but gear operated type with bevel gear box and crank handle. |
| 26 | Routine Maintainence of openable rolling shutter such as taking down and replacment of the unserviceable accessories such as (Cheek plate, roller holder curtain in plates in supported by two load bearing, flag post, Roller assembly, tubular motor, safety brake, guides and curtains and refixing in the same opening:- |
| 27 | (a) Area of shutter exc 5.00 sqm and n exc 10.00 sqm each. |
| 28 | (b) Area of shutter exc 10.00 sqm and n exc 20.00 sqm each. |
| 29 | Hacking out old broken glass (any thickness, size, quality or description) from from metal frame including punching or drilling out old glazing pins/ spring clips and providing and fixing rough cast,wired figured glass, 6.4mm thick and glazing with oil putty in square not exc 0.50 sqm in each pane all as directed. completely specified and directed by Engineer in charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysSep 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender