Tender For Supply Installation Testing, Commissioning Of 10 Cusec Capacity 10M Head Horizontal Pumping Equipment With Allied Electro Mechanical Works At Lis Pahoo Pulwama..
Tender Value
17 Lakhs
Estimated cost
Bid Submission
10 Sep 2026
15 days left
EMD
34000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pulwama → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Supply Installation Testing, Commissioning Of 10 Cusec Capacity 10M Head Horizontal Pumping Equipment With Allied Electro Mechanical Works At Lis Pahoo Pulwama..
BOQ
| Sl. No. | Item Description |
| 1 | Design, Manufacture, Supply, Installation, Testing & Commissioning of horizontal centrifugal Pumping unit for Pahoo Right. The pumping unit shall have the following specifications:-A. PUMP:-Make = Mather and Platt(M&P)/Kirloskar/equivalent make as approved by the DepartmentDischarge = 10.0 CusecDynamic Head = 10. Mtr.NPSH available = 3.30Efficiency = ≥75%MATERIAL OF CONSTRUCTION:Impeller = stainless steel ASTMA 351/CF-8M Impeller Nut = Stainless Steel ASTMA 351/CF-8MCasing lines/Wearing Ring= ASTMA 351/CF-8MImpeller Shaft = Stainless Steel AISI 410Stuffing Box = Cast IronGland = Bronze grade V of IS: 318Fasteners = High tensile SteelShaft Sleeve = Stainless Steel AISI 410Pump Casing = Close fine grained Cast Iron conforming to IS:210 grade FG-260B. MOTOR:- Type = Three phase, squirrel Cage, Electric Induction Motor Make = Kbl/ABB/C.G/Equivalent Rating = to be quoted Speed = 1000 (Synchronised) or less Operating Voltage = 415 + 10 % Volt Frequency = 50 + 3% Hz Class of insulation = F Type of Duty = Continuous Type of enclosure = TEFC. Efficinecy Class = IE2The motor shall confirm to IS: 12615 with latest amendments. The pumping unit shall be complete with Mild Steel Base Frame, fabricated as per IS 2062, requisite number of Foundation Bolts, and Pump - Motor coupling. Third party inspection certificate through the reputed/registered third partry inspection agency (EIL/CEIL/RITES) shall have be producedat the time of supply of pumping unit or before the installation of pumping unit.NOTE:The estimate includes inspection charges |
| 2 | Providing and fitting of open well submersible pump of 02HP capacity to be used for priming of below mentioned specifications: Motor: 02 HPOutlet: 2” dia.Voltage: 415Phase: 03 PhRPM: 2840The above-mentioned submersible pump shall be fitted on suction side of the pumping unit along with the below mentioned accessories.Providing and fitting of 2” dia. flexible pipe along with 02 no. tightening clamps. - 5 Mtrs.Providing and fitting of 2\\" dia. GI pipe medium class - 10 MtrsP/F of 2\\" Dia GI elbows - 3 No.P/F of 2\\" Dia GI Tee - 01 No.P/F of 2\\" dia gate valves, . - 4 Nos.P/F of 2\\" dia MS Flanges - 10 Nos.P/F of 03 HP DOL Starter - 01 No.The job also includes full load testing of the above mentioned equipment. |
| 3 | Fabrication, providing, installation and testing of 400mm Nominal Diameter, 5.0mm thick ERW ISI-mark mild steel pipes for suction of 01 No. pump as per the following technical specifications:Length of the pipe = Pipe shall be in single random length from 4 to 7 meter as per Clause 12.4 of IS 3589 10804.Type of welding = ERWQuality of MS plate to be used for manufacture = As per IS 2062Pipe to be manufactured = As per IS 3589 having one longitudinal joint with latest amendments (Grade-Fe410)Hydraulic test pressure = As per 10.1 of IS 3589End preparation = As per 17.1 of IS 3589 where V-groove is to be made by machine-grinding edges of the pipeMake = Prakash Surya/ Jindal/ SAIL/ Tata/ equivalent.Tolerances = As per clause 12.3 of IS:3589 The pipes shall be fitted with M.S flanges (mentioned below) ,washers, fasteners for end connections and on the foot valve end as per site requirement. The pipes shall be painted with two coats of anticorrosive bitumastic paint. The installation shall be carried out in accordance with IS 10804.The job includes Loading/unloading, carriage etc. |
| 4 | Providing and welding of steel plate flanges of 20mm thick on Suction/delivery pipes of 400mm nominal size |
| 5 | Fabrication, providing & installation of 400mm dia. Mild steel Flanged bend (as per site requirement) for suction side duly fitted with M.S flanges at both the ends having flange thickness 20mm. The bend shall be fabricated out of 6mm thick M.S plate. The job includes fitting material like nuts/bolts & RI Cloth washer etc & painting in one coat of steel primer and two coats of synthetic enamel of approved shade. |
| 6 | Manufacture, providing, fitting and installation of 400mm dia. Mild steel foot valve. The foot valve shall have to be fabricated out of 6mm thick Mild steel plate. The flanges fitted with the foot valve shall be of 20mm thickness.The thickness of weight plate shall be 20mm and shall be fitted with heavy duty hinge having sufficient foot valve seat dully turned on lathe and fitted with leather washer.The job also includes fabrication, providing and fitting of M.S strainer made out of 12mm sq. bars. The height of the strainer shall be 300mm other specifications of the foot valve are given hereunder:-Material= Mild steel plate Thickness of body = 6mm Thickness of weight plate = 20mmi. Thickness of the flange ... 20mmii. Inner dia. of the flange... 400mmThe foot valve shall be painted with one coat of steel primer The job includes providing and fitting of nuts and bolts and RI cloth washers. |
| 7 | Manufacturing, providing and installation of 300mm dia x350mm dia and 600mm long eccentric reducer fabricated out of 5.6mm thick Mild steel plate duly flanged on both sides. The increaser is to be fitted on the suction side of pumping equipment. The specifications of M.S flange on Reduced and enlarged side of increaser shall be as under:a). Reduced side flange:. i. Material = Mild steelii. Nominal dia. =300mmiv. Thickness = 20 mmb). Enlarged side flange: -i. Material = Mild steel ii. Nominal dia. = 350mmiv, Thickness = 20 mmThe job includes providing and fitting of nuts-and-bolts washers etc. and painting in one coat of steel primer followed by 02 coats of bituminous paint. |
| 8 | Fabrication, providing & installation of 350mm dia. Mild steel Flanged bend (as per site requirement) for suction side duly fitted with M.S flanges at both the ends having flange thickness 20mm. The bend shall be fabricated out of 5.6mm thick M.S plate. The job includes fitting material like nuts/bolts & RI Cloth washer etc & painting in one coat of steel primer and two coats of synthetic enamel of approved shade. |
| 9 | Fabrication, providing, installation and testing of 350mm Nominal Diameter 5.6 mm thick ERW ISI-mark mild steel pipes for delivery side of 01 no. pump as per the following technical specifications:S.No Details Requirement1 Nominal Diameter = 350 mm2 Thickness = 5.6 mm3 Length of the pipe = Pipe shall be in single random length from 4 to 7 meter as per Clause 12.4 of IS 35894 Type of welding = ERW5 Quality of MS plate to be used for manufacture = As per IS 20626 Pipe to be manufactured = As per IS 3589 having one longitudinal joint with latest amendments (Grade-Fe410)7 Hydraulic test pressure = As per 10.1 of IS 35898 End preparation = As per 17.1 of IS 3589 where V-groove is to be made by machine-grinding edges of the pipe9 Make = Prakash Surya/ Jindal/ SAIL/ Tata/ equivalent10Type of welding to be used for joining pipes = DC arc welding 11 Tolerances = As per clause 12.3 of IS:3589 The delivery pipes shall be fitted with welding and flanges for end connections as per the instructions of engineer in charge. The pipes shall be painted with two coats of anticorrosive bitumastic paint. The installation shall be carried out in accordance with IS 10804.The job includes loading/unloading carriage etc. |
| 10 | Supply, Installation, Testing and Commissioning of Pump controler of below mentioned specification:Fitted with Single phase Preventer,auto start relay arrangement ,protection fromPhase reversal, Dual Analog volt- Ammeter ofapplicable range with Phase selector switch for Volt meter &ammeter.Type/Model: MU-G 75FASD/Equivalent No. of phases:3phase, Relay range : 66-110Amp.HP:75 Preferred Make: L & T or Equivalent |
| 11 | Providing, fitting, sizing, laying, testing and commissioning of XLPE insulated unarmoured 1.1KV single core 95mm2 Aluminium cable for use of internal wiring of electrical equipment. The cable shall be of preferably Grindlay/Havells/ imperial/ Polycab/ equivalent make & shall be as per relevant IS 7098 part-1 specifications. The job also includes crimping of terminal ends with Hydraulic tool & providing & fitting of aluminium conductor sockets/thimbles etc. The job also includes the fitting of cable along the walls of the pump house/premises by using GI clamps and using canvas pipe at the ends. |
| 12 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. |
| 13 | CEMENT CONCRETE Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 14 | steel reinforcement for rcc work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level TMT Bars of Fe 500d or more T |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns |
| 16 | providing and laying nallah/crushed stone aggregate 80-100 mm nominal size including carriage. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender