Tender For Certain Repairs To Compound Wall, Gate / Grill Grating And Chain Link Fencing, Drain, Path And Certain Petty Repairs In Md Accn At Trv, Mt Pool, Csd Complex, Spectrum And Inliving Sailor Accn At Coast Guard Of Age B/R-I Under Ge Haddo, Sri
Tender Value
41 Lakhs
Estimated cost
Bid Submission
11 Sep 2026
19 days left
EMD
82000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Repairs To Compound Wall, Gate / Grill Grating And Chain Link Fencing, Drain, Path And Certain Petty Repairs In Md Accn At Trv, Mt Pool, Csd Complex, Spectrum And Inliving Sailor Accn At Coast Guard Of Age B/R-I Under Ge Haddo, Sri Vijaya Puram
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames area n. exc 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed |
| 2 | Taking down Chowkats exc 1.5 Sqm but n. exc 4 Sqm each with shutters (Without taking off shutters from the frame) complete all as specified and directed |
| 3 | Taking down chowkhat or frame area n exc 1.5 sqm each etc, completed all as specified and directed. |
| 4 | Taking down chowkhat or frame area exc 1.5 sqm but n exc 4 sqm each etc, completed all as specified and directed. |
| 5 | Supply and fix PVC door frame of size 50mm X 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening but wood grain printed PVC sheet & edges will be painted to match printed sheet, etc complete all as specified and directed. |
| 6 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, but Single Side Prelam PVC sheet used instead of Plaincolour PVC sheet and stile & railshaving one side feathered edge and on other side 10mm 900 bent edge, suppling & fixing in the frame at site as per specification & drawing complete as per direction of Engineer-in-Charge |
| 7 | Supply and fix for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45x70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 8 | Supply and fix for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 9 | Supply and fix for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 10 | Supply and fix for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 11 | Supply and fixing stainless steel (SS-304 grade) hinges 100x62x2.5 mm of approved quality, with necessary stainless steel screws etc, complete all as specified and directed. |
| 12 | Supply and fix 200 mm long of Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 13 | Supply and fix 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 14 | Supply and fix 150mm extruded aluminum alloy handles, cast type, anodized complete all as specified and directed. |
| 15 | S & F for Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt in 300 mm etc complete all as specified and directed. |
| 16 | S& fixed for 150 mm length of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 17 | S& fixed for Aluminium (die cast body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 18 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, etc all as specified and directed. |
| 19 | Taking down Aluminium Windows chowkhats or door frames with shutters without taking off shutters from frames exe 1.5 Sqm and n.exc 4 Sqm each etc complete all as specified and directed. |
| 20 | Taking down Aluminium Windows and Ventilator chowkhats or frames with shutters without taking off shutters from frame n. exe 1.5 Sqm each etc complete all as specified and directed. |
| 21 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators, partitions and shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 22 | S&F for Powder coated Aluminium grill (minimum thickness of powder coating 50 micron) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in charge. |
| 23 | M&L for 12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to timber or Aluminium frame work etc all as specified and directed. |
| 24 | Supply only plain sheet glass 4.0 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum window shutter not exc 0.5 Sqm in each pane etc complete all as specified and directed. |
| 25 | Supply only figured glass, pin head type sheet glass 4.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window shutter not exc 0.5 Sqm in each pane etc complete all as specified and directed. |
| 26 | M&L for 12mm thick sheet glass toughned glass as in hinged doors, partitions automatic doors closer, and similar work including cutting to shape, drilling holes required etc, if sheet glass is ground or obscured or frosted, on one side including hacking out old glass panes complete all as specified |
| 27 | S&F Stainless Steel EGF combo with lock heavy duty automatic floor spring (80Kg) load, with necessary fitting, etc all as specified and as dierected. Make : Godrej or equivalent as approved by GE. |
| 28 | S&F Stainless Steel A2 Combo of Sliding Door System Kit, Grade: 304 with necessary fitting, etc all as specified and as dierected. |
| 29 | Supply only Aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples or beading etc complete all as specified and directed. |
| 30 | S&F in repairs Aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples or beading etc complete all as specified and directed. |
| 31 | Dismantling boarding, shelves, partitions of any description, fixed in any position with nails, screws, clamps, etc all as specified and directed. |
| 32 | M&L for HDF boards (fire & water proof) of 18mm thick as in cub boards, cabinet, shelves etc & the like with decorative choice lamination on one side and balancing white lamination on other side with necessary fitting etc, complete all as specified and as directed. |
| 33 | S&F Auto concealed hinges stainless steel grade AISI-316 (type Austenitic anticorrosive in nature) suitable for kitchen cabinets, cub boards, Shelves etc complete all as specified and as directed. |
| 34 | S&F SS Fancy 'D' Type Drawer / Cabinet handles of Size 100mm, etc all as specified and as dierected. Make Prayag Cat No SSB-2100) |
| 35 | S&F Magnetic catcher with plate, glossy finish for Drawer / Cabinet of Size not less than 50mm, etc all as specified and as dierected. Make Prayag Cat No MDC-W55) |
| 36 | S&F Stainless steel Telescopic channel 18 inches length with necessary fitting, etc all as specified and as dierected.Make Godrej Cat No 9721) |
| 37 | S&F Stainless steel 25mm thick glass door full handle 14 inches length with necessary fitting, etc all as specified and as dierected. Make Prayag Cat No SH25-14P-SS) |
| 38 | Dismantling plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof coverings complete all as specified and directed |
| 39 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed |
| 40 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, fixed with self tapping screws all as specified and directed |
| 41 | S & F for 2mm thickness fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc if fixed with L-type or J-type or cranked hook bolts in lieu of screw including dismantling wrought iron or mild steel work of any description and in any position not otherwise provided etc, complete all as specified and directed. |
| 42 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed |
| 43 | S&F for 0.71 mm thickness Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) with necessary fittings etc, complete all as specified and directed. |
| 44 | Dismantling structural steel work of any description complete all as specified. |
| 45 | M&L for rolled section as in main and cross beam, hip and jack rafter,purlins where connected to common rafters and running rails and guides for sliding doors fixed witg angle cleats or other connecting plates of grade Fe-410 (grde E-165) etc complete all as specified and as directed |
| 46 | M&L for aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering and including dismantling of old wind tie etc fixed with self tapping screws as specified. |
| 47 | Dismantling of ceiling boards including grid of any description fixed in any position with nails or screws etc all as specified and as directed. |
| 48 | S&F for anodoised aluminium powder coated snap grid frame work for ceiling 605mm x 605mm using aluminium anodised sections aluminium sections main tee 36.5X25X1.4mm, cross 23.5X26.4X1.4mm, angle 25X25x1.4mm including cutting, drilling jointing etc complete including 4mm dia of GI hangers wire suspenders fixed with adjustable connectors and providing 6mm thick E-boards (Classic) 605mm x 605mm size Specified by Engr-in-charge and making good etc complete all as specified and as directed. |
| 49 | M & L for seamless false ceiling made out of 12mm thick of gypsum board fixed to the ceiling section with 25mm long self drilling and tapping screws having Philips head with under head cutter at 200mm centre to centre, including finishing the joints of face board with specially formulated joining compound and 48 mm wide fibre tape to provide seam less finish and including GI channel 0.55 mm thick with two unequal flanges of 20 to 30mm and web of 27 mm fixed to surrounding wall using nylon sleeve and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 215 mm each and web of 45 mm suspended from soffits at approx. 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.20mtr length) of 0.55 mm thick having kurled web of 50 mm and flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including 6mm thick GI hangers adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40x3 mm size long and expansion hold fasteners 12.5mm dia 40mm long including thin layer of Pop with Gypsum binder, sanding the surfaces till smooth surface is obtained and finally applying two coats of acrylic emulsion over one coat primer over 3mm thick putty all as specified and as directed |
| 50 | S&F PVC insulation panels (thickness of insulation pannel 10mm) with EPS stuck to 1mm plain PVC sheet suitable placed in false ceiling grid made of Anodised aluminium snap grid frame work for false ceiling and including 6mm thick GI hangers adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40x3 mm size long and expansion hold fasteners 12.5mm dia 40mm, long including dismantling of ceiling boards including grid of any description fixed in any position with nails or screws etc all as specified and as directed. |
| 51 | M&L in repairs to 12 mm thick WPC (Wood-Plastic Composite) louvers Panel boards as in Wall panelling work fixed over frame work using suitable aluminium profile sections of size 50mmx25mmx2mm thick and fixed with suitable screws / fasteners as per the site requirents etc complete all as specified and directed.Note: Design and Pattern will be finilized by the Engr In charge. |
| 52 | M&L for 6 to 8mm thick HDF Laminate boards with plain coloured, textured wooden finish / embossed surface, grooved / interlocking boards fixed to the existing flooring over 3mm foam layer fixed using suitable adhessive or as per the manufacturer's instrctions, etc complete all as specified and as directed. |
| 53 | M&L for 6 to 8mm thick HDF Laminate boards with plain coloured, textured wooden finish / embossed surface, grooved / interlocking boards as in vertical surfaces / skirtings etc fixed using suitable adhessive or as per the manufacturer's instrctions, etc complete all as specified and as directed. |
| 54 | M&L in repairs to 18 mm thick rubco huat rubwood in built up interiors as in cupboards, shelves wall lining, box structure and including all fitting items complete all as specified and directed. After completing the carpentry works all the visible woods area will be sanding by No.60 & 80 Wood Sanding Paper, after that will be applying Sheenlac make Filler with mixing of NCD Thinner (Sheenlac make), then pasting Chock Putty in the shabby/nailing area which will be sanding with No.120 Sanding Paper, after that will applying Sealer of Sheenlac make and walnut colour stainer, then cutting with No. 320 Sand Paper, after completing the above process will spray Melamine Polish of Berger/Sheenlac make then cutting with No.400 Sanding Paper. Finally will applying Silicon make: Waxpol with soft Banyan Cloth for better shining/finishing. Make of rubber wood members: RUBCO or equivalent |
| 55 | M&L for 30mm thick rubber wood superior quality, chemically pressure treated, egde glued, finger jointed, tongued, grooved as in door shutter and finished with two coats of melamine polish with asian sealer and wood filler over a coat of honey/natural colour wood filler putty for dust free surface etc including preparation and applying three types of sand papers and surface finish to a glossy/ mat finish to match with the adjoining surface complete all as specified and as directed. Make of Rubber Wood members : RUBCO/ India Wood or equivalant |
| 56 | S & F 8mm thick fibre cement plank ( size 3.00 x 0.15m ) of any colour fixed in position with suitable screws/ fasteners as per manufactures instructions on aluminium/ mild steel work in wall cladding including applying two coats of exterior emulsion paint on fibre planks complete all as specified and as directed. Note: Aluminium/ Mild steel work shall be measured and paid seperately. Make : Sheera of M/s Mahaphant Fibre cement (South Asia) Pvt Ltd or its equivalent as approved by GE. |
| 57 | M&L in repairs to Aluminium composite panel sheet of 3.0mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30.0micron fixed over frame of aluminium tabular section 50x25mmx 2.0mm thick, having panels not exc 1200x1200mm with necessary silicon filling, in approved pattern as in column, beam, wall at any height with necessary scafoldings etc complete as specified and as directed. |
| 58 | M& L for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layers 15 mm thick in cement mortar (1:6) for laying floor finishes including dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.complete all as specified and directed. |
| 59 | S&F Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or colored cement to match including screed bed or bedding layers 15 mm thick in cement mortar (1:6) for laying floor finishes including dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed. complete all as specified and directed. |
| 60 | S&F glazed ceramic coloured tiles (350x450 x 7mm thick ) on dado & skirting , set and jointed in neat cement slurry and pointed in white or colored cement to match including 10 mm thick rendering with rough finished in cement mortar 1:4 to received tile including dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed. etc, complete all as specified and directed. |
| 61 | M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms,floor, walls and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and polishing including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 62 | Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed. |
| 63 | S&F mild steel roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) quality-A all as specified and directed |
| 64 | S&F for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete etc, complete all as specified. |
| 65 | S&F for mild steel flat iron 40 x 5mm for seceuring wire mesh etc including necessary drilling holes etc conforming to Fe-290(Gde E-165) etc, complete all as specified. |
| 66 | S&F for rolled mild steel angle, Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-290 Gde E-165 etc, complete all as specified. |
| 67 | S&F mild steel screw bolts(Machine made) with hexagonal or square head at one end and screwed the other end n exc 5 cm long and diametre of neck exc 5 mm but n exc 10 mm dia etc, complete all as specified and as directed. |
| 68 | S & F for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured),etc complete all as specified and directed. |
| 69 | S&F in repairs 600mm dia concertina coil fencing conforming to IS 4454 Part-I, made out of 2.6mm (+ or - 2%) dia of steel core wire galvanised and with anti rust coating (Black colour), with coils not less than 51 turns for an effective stretched length of 6m with 2 handles, duly placed on existing supports over security/ compound walls and tied with 2mm dia binding wire and the spikes at the ends of coils embedded into PCC coping all as specified and as directed. Note: PCC coping shall be measured and paid separately. |
| 70 | S&F in repairs 600mm dia concertina coil fencing conforming to IS 4454 Part-I, made out of 2.6mm (+ or - 2%) dia of steel core wire galvanised and with anti rust coating (Black colour), with coils not less than 51 turns for an effective stretched length of 6m with 2 handles, duly placed on existing supports over security/ compound walls and tied with 2mm dia binding wire and the spikes at the ends of coils embedded into PCC coping all as specified and as directed. Note: PCC coping shall be measured and paid separately. |
| 71 | M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C1, using 20mm graded stone aggregate, set in CM 1:6, including demolition of brickwork or stone / boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc, complete all as specified and directed. |
| 72 | M&L for plain cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases etc, including demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level all as specified and directed. |
| 73 | M&L PCC 1:2:4 type B2 (40mm grade stone agg) as in cement concrete in surface channel and drain, including demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level all as specified and directed. |
| 74 | Material and labour for providing Plain Cement Concrete (1:2:4) type B1 using 20 mm graded aggregate as in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones etc water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work, including demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level all as specified and directed. |
| 75 | Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level all as specified and directed. |
| 76 | M&L for providing PCC 1:3:6 type C2 (using 40mm graded stone agg) as in plinth protection 75 mm thick finished over and smooth without using extra cement etc all as specified and directed. |
| 77 | M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in 75mm thick as in sub base complete all as specified & directed by Engineer-in-Charge. |
| 78 | S&F for glossy finished chequered cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry over and including 20 mm thick screed bed in CM(1:6) etc all as specified and as directed. |
| 79 | S&F for Heavy Duty Ceramic Parking tiles 30cmx30cmx8-10mm thick set jointed with grey cement and pigment and pointed in neat cement slurry over and including 20 mm thick screed bed in CM(1:6) etc all as specified and as directed. |
| 80 | M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 81 | M&L for Providing plain cement concrete of Type B1 1:2:4 (20 mm graded aggregate) as in kerbs of mud stops, borders, etc,. rounded or chamfered on edges, all as specified and as directed. |
| 82 | Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified. |
| 83 | M&L for Reinforced cement concrete Type B1,1:2:4 using 20mm graded stone aggregate in Slab supported on walls, as in Shelves all as specified and directed. |
| 84 | M&L for use of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thickrough finished flat concrete surfaces all as specified and directed. |
| 85 | Material and labour for Mild steel TMT bars of Fe 500 or Fe 500D, 8 mm to 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified. |
| 86 | Material and labour for Mild steel TMT bars of Fe 500 or Fe 500D, 8 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified. |
| 87 | M&L for rendering 15mm thick in cement mortar 1: 4 mixed with water proofing compound on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, including taking down cement plaster on brick or concrete surfaces wall etc. including racking out joints hacking for key scrubbing down with water etc complete all as directed.Note: Water proofing compound shall be measured and paid separately. |
| 88 | Supply only integral water proofing compound all as specified and as directed. |
| 89 | M&L rendering 10mm thick in CM 1:6 on brick surfaces and finished even and smooth w/o using extra cement etc, including taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc completed all as specified and directed. |
| 90 | M&L for rendering 5mm thick in cement mortar 1:3 on fair faces of ceiling concrete surfaces finished even and smooth without using extra cement complete all as directed. |
| 91 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed. |
| 92 | Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc, all as specified and directed |
| 93 | M&L for new plastered on walls and applying two coats of oil bound distemper over a preparatory coat of 1mm thickess of plaster of paris putty on plastered surface over a coat of priming plastered and other surfaces with alkali resistant priming paint, including necessary preparation of surfaces etc, completed all as specified and directed. |
| 94 | M&L for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed |
| 95 | Taking down of damaged/ loosened cement concrete/cement mortar in RCC walls/soffits of slabs and similar structure members up to depth of 20mm to 40mm. Cleaning the dismantled portion with wire brush, etc to remove dust , dirt and other foreign particles and washing with water under pressure and applying bonding agent on old concrete surfaces all as per manufacturers instruction, Providing and applying two coats of rust preventive slurry made of \\"Polyalk Fixoprime\\" or equivalent in portion 1:1.5 to existing reinforcement bars over prepared surfaces provide and apply 20 mm thick High build polymer modified cement sand mortar ( 1:2.5 ) mixed with 10 liters (minimum) Nitobond SBR per 50 kilogram of cement of M/s FOSROC chemical ( India ) Pvt Ltd or Equivalent product of manufacturer all as manufacturers instruction including necessary scaffolding up to 12 m height complete and finally applying two coats of oil bound distemper with roller finish over a coat of chalk whiting primer over an avg 2mm thick of wall care putty all as specified and directed. |
| 96 | Supply only polyester triangular fibres as secondary reinforcement in all types of concrete and mortars, etc complete all as specified and directed. |
| 97 | S&F in for Corner glass self assembly size 300mm with chromium plated bracket guard and railing (Make: Prayag Cat No. BEA-44 or Equivalent approved) |
| 98 | S & F in repairs vitreous china wash down single piece WC Rimless Bowl with Cistern for Coupled WC with UF Soft Close Slim Seat Cover, Hinges, Dual Flush Cistern Fitting, Conversion Bend, Fixing Accessories and Accessories Set, with 'S' or 'P' trap and other connecting items approved brand including fix with white cement complete. Make-Jaquar Cat Pt No.OPS-WHT-15753NS250UFSMZ or equivalent in Parryware/Cera/Prayag |
| 99 | S&F in repairs CP towel rail 20 mm dia, 60 cm long and and including chromium plated brass screws and wooden/plastic cleat. |
| 100 | S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action push type with inlet ball valve and float including flush pipe long 32mm dia, ball valve, handle, bracket etc complete all as specified and directed |
| 101 | S & F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) , bolts and flushing pipe but including seat cover, jet pressure with hinges device complete all as specified and directed. |
| 102 | S&F in repaiar Vitreous china squatting pan, Orissa pattern, size 580x440 mm white with integral foot rest (excluding flushing cistern and flushpipe ) including provision of cement concret bedding all as specified and directed. |
| 103 | S&F in repairs for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified |
| 104 | S&F in repairs plastic water closet seat for EWC, closed pattern with flat bottom and cover, any colour and mild steel chromium plated or aluminium hinging device complete all as specified and directed. |
| 105 | S&F of soft closing type plastic WC seat cover with lid of approved make and shade, complete with stainless steel hinges, rubber buffers, all necessary fittings and fixtures, fixed to existing WC pan, including tightening, adjustment and making good complete in all respects. Make ; Jaguar Cat No ; CNS-WHT-853S300SPPSM. |
| 106 | S & F in repairs for wall mixer 3-in-1 system with provision for both hand shower and over head shower composite with 115 mm long bend pipe connecting legs & wall flanges Mixer (Make: Prayag Cat No PIS-80H or Equivalent approved), hand shower including 1.5 mtr flexible tube with hook Cat No BHS-99 of Prayag or Equivalent, and over head showerwith arm and flange (300mm) of cat No BS-69 of Prayag or Equivalent in Jaquar. |
| 107 | M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer all as directed.NOTE: The item of BOQ shall be executed in high rise building. The contractor shall arrange necessary scaffolding/ shoring, water pressure jet pump and other safety measures to be undertaken including insurance cover for the workers engaged by him during the execution of work. The rate quoted by the contractor for the above items shall be inclusive of the above provisions . Nothing extra on this account is admissible. Please Enable Macros to View BoQ information |
| 108 | M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer all as directed.NOTE: The item of BOQ shall be executed in high rise building. The contractor shall arrange necessary scaffolding/ shoring, water pressure jet pump and other safety measures to be undertaken including insurance cover for the workers engaged by him during the execution of work. The rate quoted by the contractor for the above items shall be inclusive of the above provisions . Nothing extra on this account is admissible. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysSep 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender