Tender For special Repair To Bldg No. A-53& A-54 At Signal Unit, Happy Valley, Shillong And Provn Of Parking Shed At Se Falls And Addn/Altn Of Bldg No. Sp-12 At Cwe Shillong Under Ge Shillong
Tender Value
40.66 Lakhs
Estimated cost
Bid Submission
11 Sep 2026
15 days left
EMD
81320
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Khasi Hills → Meghalaya
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No. A-53& A-54 At Signal Unit, Happy Valley, Shillong And Provn Of Parking Shed At Se Falls And Addn/Altn Of Bldg No. Sp-12 At Cwe Shillong Under Ge Shillong
BOQ
| Sl. No. | Item Description |
| 1 | S&F 2nd class HW boarding 20mm thick fixed with nails as in eaves board planed one side with butt joint complete all as specified and as directed. |
| 2 | M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:-(i) Taking out old roof treatment and roughening the same old concrete slab by picking, sweeping clean and washing down with water to remove dust etc.and applying cement slurry @3kg/Sqm(ii) Screed bed or bedding layer of mortar 1:4 in 15 mm thick for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (Note: WPC shall be measured and paid for under separate items)(iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986.(iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction.(v) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm. |
| 3 | M&L for 600 mm x 600 mm 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with nails as in ceiling,including dismantling wall and ceilling boards of any description including cover fillets complete all as specified and directed. |
| 4 | Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section of unframed work complete all as specified and as directed. |
| 5 | M&L for Anodised aluminium snap grid frame work for false ceiling complete all as specified and as directed. |
| 6 | M&L for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed. |
| 7 | Demolition of brick work / Precast cement concrete block walling in any position, built in any mortar complete all as specified and directed. |
| 8 | M&L Precast PCC (1:3:6) type C1 (using 20mm graded agg) solid block masonry exc 10cm in width or girth and setting CM (1:6) complete all as specified and directed. |
| 9 | Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MD land complete all specified and directed. |
| 10 | M&L for rendering 10 mm thick on concrete surface in cement mortar (1:6) as backing coat and 5 mm th in CM 1:4 finishing the surface even and smooth without using extra cement, mixed with water proofing compound as per manufacturer's instructions complete all as specified and directed. Note:- WPC shall be measured & Paid separately under respective item of BOQ. |
| 11 | M&L for 10mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed. |
| 12 | M & L for rendering 5 mm thick in CM 1:3 on ceiling surfaces of cement concrete and finished the surface even and smooth without using extra cement complete all as specified & directed . |
| 13 | Supply only integral water proofing compound (Powder) complete all as specified and directed. |
| 14 | M&L for preparing plastered or unplastered surfaces of wall after complete removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed |
| 15 | M&L for preparation of newly plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 16 | M&L for Complete removal of existing treatment of wall and applying 1mm thick of Birla white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed. |
| 17 | M & L for preparation of newly plastered/concrete surfaces of walls, providing 1 mm thick of Birla white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified. |
| 18 | M&L for preparation of old plastered surfaces of ceiling and providing 1mm thick of Birla white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed. |
| 19 | M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 20 | M&L for preparation of old painted of steel or iron surfaces of any description not otherwise described over 10cm width or girth and applying one coat of Synthetic enamel paint complete all as specified. |
| 21 | Demolition of plain cement concrete (unreinforced) in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 22 | M&L for Hard core, broken stone /boulders of gauge n exc 63 mm size , deposited , spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 23 | M&L for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone agg) as in plinth protection/path incl finishing even & smooth with using extra cement, complete all as specified and directed. |
| 24 | M&L for PCC 1:3:6 type C2 (using 20mm graded aggregate) as in surface channels and drains complete all as specified and directed. |
| 25 | Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. |
| 26 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 27 | M&L for 25mm thick PCC 1:2:4 type B-0 (Using 12.5 mm graded crushed stone aggregate) as in levelling coarse of tile flooring etc complete all as specified and directed. |
| 28 | M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and directed. |
| 29 | M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in Skiritng etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including with 10 mm thick baking course in CM 1:4 including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed. |
| 30 | M&L Non-skid ceramic coloured tiles 7 to 8 mm thick , (square/rectangular), area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 complete all as specified and directed. |
| 31 | M&L Glazed ceramic coloured tiles of size 450 x 300 x 7mm thick (premium/special quality) as in vertical surfaces of wall etc set and jointed with neat cement slurry and pointed in white or coloured cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 including dismanthing floor/hearth or wall tilling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off premises complete all as specified and directed. |
| 32 | Demolition of stone slabs and granite laid, bedded, jointed and pointed in any mortar of any description or thickness in floors, aprons cills or plateform etc complete all as specified and directed. |
| 33 | M&L for rounding to edges of stone slabs one edge, such as in steps cooking plateform, and other similar situation complete all as specified and directed. |
| 34 | M& L for Machine cut kota stone slab flooring 20-25 mm thick jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 20 mm thick screed bed in CM 1:3 including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed. |
| 35 | M& L for Kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over cement screed and jointed with and including 10 mm thick baking course in CM 1:4 including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed. |
| 36 | M & for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. |
| 37 | M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set jointed and pointed in neat cement slurry in floor with grey cement and pigment over and including 15mm thick screed bed in cement mortar 1:4 including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed. |
| 38 | M&L for Pre cast RCC 1:2:4 Mix, type B1 (using 20 mm graded crushed stone aggregates) as in cover slab for soakage well / manhole and similar works supported on walls set in cement mortar 1:6 complete all as specified and directed.Note:- Reinforcement steel will be measured & paid separately. |
| 39 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including bending, and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 40 | Demolition of plain cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 41 | M&L for PCC 1:5:10 Mix, type E2 (using 40mm graded crushed stoneagg) as in sub base of WC complete all as specified and directed. |
| 42 | Demolition cement Concrete (RCC) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 43 | S & F 500 litres capacity double layer, rotational molded, polythene (white colour), tripple layer water storage tank, ISI Marked (Cylindrical vertical with closed top),colour white , hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including dismantling complete all as specified and directed. |
| 44 | S & F 1000 litres capacity double layer, rotational molded, polythene (white colour), tripple layer water storage tank, ISI Marked (Cylindrical vertical with closed top),colour white , hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including dismantling complete all as specified and directed. |
| 45 | S&F in repair 20mm dia Ball cock valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0 m m - 2 1 0 g m s ) complete all as specified and directed. |
| 46 | Taking up or down GI tubing 15mm dia and connections including removing to store complete all as specified and directed. |
| 47 | Supply and fix 15 mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line complete all as specified and directed. |
| 48 | Refixing only 15mm tubes any grade, to walls and ceilings or laying in floors including provision of all new fittings complete all as specified and directed. |
| 49 | Taking up or down GI tubing 20mm dia and connections including removing to store complete all as specified and directed. |
| 50 | Supply and fix 20 mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line complete all as specified and directed. |
| 51 | Refixing only 20mm tubes any grade, to walls and ceilings or laying in floors with provision of all new fittings complete all as specified and directed. |
| 52 | M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete all as specified and directed. |
| 53 | S&F in repair 15mm bore stop cock cast copper alloy, fancy type, chromium plated, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and directed. . |
| 54 | S & F in repair 15 mm bore CP fancy type bib tap long body cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 55 | S & F in repair 15 mm bore CP fancy type 2 in 1 bib tap long body cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 56 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect all as specified and directed. |
| 57 | S&F in repair brass chromium plated tubular towel rail 600mm long between the flanges and 20mm dia complete all as specified and directed. |
| 58 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 59 | S&F in repair for PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 60 | S&F as in repairs.Vitreous China wash down water down water closet pan (P-Trap pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 61 | S & F in repair Vitreous china squatting pan of pattern Orissa Pattern of size 580x 440 mm white with PVC ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( 1:5:10, using 40 mm graded stone aggregates), and finishing the top surfaces to match with the existing flooring as in repairs (bore 110 mm) complete all as specified and directed. |
| 62 | S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; complete all as specified and directed. |
| 63 | S & F in repair PVC (Plastic polymer Cistern) valve less, Syphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as specified and directed. |
| 64 | S&F in repairs Vitreous china WHB, white, flat back, of size 550 x 400 mm including brackets, waste coupling 32mm, and waste Pipe, 32mm incl pedestal complete all as specified and directed. |
| 65 | S&F in repair pillar tap 15 mm, brass, chromium plated, fancy type complete all as specified and directed. |
| 66 | S&F in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed. |
| 67 | S&F in repair PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed. |
| 68 | S&F in repair PVC (SWR) vent cowl 110mm dia complete all as specified and directed. |
| 69 | S&F in repairs PVC (SWR) bend with access door of 110mm bore complete all as specified and directed. |
| 70 | S&F in repairs PVC (SWR) bend with access door of 75mm bore complete all as specified and directed. |
| 71 | S&F in repair PVC (SWR) 110mm dia in junction single, (Single T) equal or unequal complete all as specified and directed. |
| 72 | S&F in repair PVC (SWR) 75mm dia in junction single, (Single T) equal or unequal complete all as specified and directed. |
| 73 | S & F in repair 75mm dia of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 74 | Taking down chowkhats or frames with shutter without taking off shutter from the frame area exc 1.50 sqm but not exc 4 sqm each & removing from site complete all as specified and directed. |
| 75 | Taking down chowkhats or frame with shutter without taking off shutter from the frame area not exc 1.50 sqm & removing from site complete all as specified and directed. |
| 76 | Resecuring or easing & adjusting without taking down the shutter of any description area exc 1 Sqm and n.exc 2 Sqm complete all as specified and directed. |
| 77 | Taking down shutter of any description area n.exc 1 Sqm each complete all as specified and directed. |
| 78 | Taking down shutter of any description area exc 1 Sqm but not exc 2.00 sqm each complete all as specified and directed. |
| 79 | S&F MS flat iron such as small articles for hold fast and similar work complete all as specified and directed. |
| 80 | M&L for providing PCC (1:2:4 Mix) type B1 (Using 20mm graded crushed stone aggregate) for fixing hold fast including necessary form work complete all as specified and directed. |
| 81 | Supply and fixing 2nd class HW plain solid straight chowkhats/frame wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed. |
| 82 | Supply and fixing 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (without sash bars ), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. |
| 83 | Supply and fixing 2nd class HW 35mm thick plain framed panelled shutters (any number of panels), with panel of timber flats on both sides or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified and directed. |
| 84 | Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 85 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 86 | S&F powder coated (min powder coating 50 micron) anodised aluminium frame for doors, windows , ventilators plain or sliding type with one or more rebates including joining cleat for fixing etc complete all as specified and as directed |
| 87 | S&F powder coated (powder coating min 50 micron) anodised window and ventilator shutters side hung/sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 no) suitable handle (1 no ) complete all as specified and directed. |
| 88 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified and directed. |
| 89 | S&F in repair stainless steel decorative pattern holder/end brackets suitable for drapery rod of 25 mm dia complete all as specified and directed. |
| 90 | S&F in repair stainless steel decorative pattern end support suitable for drapery rod of 25 mm dia complete all as specified and directed. |
| 91 | S&F in repair 25 mm dia stainless steel drapery rod not less than 1mm thick cut to size and fixed in position, including Standard screw complete all as specified and directed. |
| 92 | M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 93 | Supply and fixing 100mm size butt hinges cold rolled mild steel medium weight, ISI marked complete all as specified and directed. |
| 94 | Supply and fixing 200mm size MS barrel tower bolt stove enamelled black with bright bolt ISI marked complete all as specified and directed. |
| 95 | Supply and fixing 150mm size MS pressed handle oval type stove enameled black complete all as specified and directed. |
| 96 | Supply and fixing 250mm long MS sliding door bolt, plate type, stove enameled black with bright bolt not less than 12mm dia with and including a min of siz bolt & nuts four on bolt & two on staple,ISI marked, complete all as specified and directed. |
| 97 | S & F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 98 | S & F 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 99 | Supply and fixing in repairs 250mm long MS sliding door bolt, plate type, stove enameled black with bright bolt not less than 12mm dia with and including a min of siz bolt & nuts four on bolt & two on staple, ISI marked, complete all as specified and directed. |
| 100 | Supply and fixing in repair 200mm size MS barrel tower bolt stove enameled black with bright bolt ISI marked complete all as specified and directed. |
| 101 | Supply and fixing in repair 150mm size MS pressed handle oval type stove enameled black complete all as specified and directed. |
| 102 | S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 103 | S & F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 104 | S&F 3 mm thick sheet glass ordinary quality and glazing fixed to aluminium frame area exc 0.50 sqm each pane complete all as specified and directed. |
| 105 | S&F 4.80 mm thick sheet glass ordinary quality and glazing fixed to aluminium frame area exc 0.50 sqm each pane complete all as specified and as directed. |
| 106 | S&F 4.80 mm thick frosted sheet glass and glazing fixed to aluminium frame area exc 0.50 sqm each pane complete all as specified and directed. |
| 107 | M&L for Forming jambs, etc. to openings in CM 1:6 (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed. |
| 108 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 109 | S&F MS frame work such as grills grating etc, with ends of bar shouldered and or riveled, or forged into spickes framed guared bars and similar work complete all as specified and directed. |
| 110 | M&L for preparation of new steel surfaces exc 10cm width or girth and applying of two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed . |
| 111 | Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep for foundation etc and getting out in soft / loose soil complete all as specified directed. |
| 112 | Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25 cm soft/ loose soil complete all as specified and directed. |
| 113 | Removing excavated materials n exc 50 m and depositing where directed at a level n exc 1.50 mtr above the starting point complete all as specified and directed. |
| 114 | M & L for PCC 1:4:8 Mix, type D2 (Using 40mm graded crushed stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed. |
| 115 | M & L Reinforced cement concrete, 1:1.5:3 Mix, Type A-1 ( using 20 mm graded crushed stone aggregate) as in Foundations, including afts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 116 | M & L Formwork flat for rough finished concrete surfaces, sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter complete all as specified and directed. |
| 117 | M&L for 5mm dia TMT bars 5 mm dia and over upto and including 10mm dia as in stirrups, spacers and binders including bending, and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 118 | S & F structural steel work as in roof trusses (framed), trussed, purlins etc conforming to FE-410-W(Gde-E-250) complete all as specified and directed. |
| 119 | S & F structural steel work as in joist, channel, angle, ISMB or tee sections, fixed independently as in post conforming to FE-410-W(Gde-E-250) complete all as specified and directed. |
| 120 | S&F MS Plates Fe-410-W(Gde-E-250) quality-B (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. |
| 121 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 122 | S & F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, eaves board, ridges, hips,valley gutters, drip and straight flashing cladding to wall etc, fixed with self tapping screws complete all as specified and directed. |
| 123 | Dismantling plain or corrugated steel sheeting, any guage, thickness incl nainital or similar pattern as in roof coverings. |
| 124 | Dismantling Timber scantlings 40 sqmcm and over in section in any position framed work complete all as specified and directed |
| 125 | Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. |
| 126 | Dismantling Wall and Ceiling Boards (Fibre ,Pulp,insulation ,etc)or insulation boards /slabs/blankets ,any thickness,including cover fillets complete all as specified and directed. |
| 127 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded in natural ground portion and making good disturbed ground complete all as specified and directed. |
| 128 | M & L for Sand filling under floors or in foundations including watering including consoildation complete all as specified and directed. |
| 129 | M & L for RCC 1:1.5:3 Mix, Type A1 (Using 20 mm graded crushed stone aggregate ) nominal mix as in slabs supported on walls , coloumns and similar complete all as specified as and directed. |
| 130 | M & L for RCC 1:1.5:3 Mix, Type A1 (Using 20 mm graded crushed stone aggregate ) nominal mix as in Chajjas beams,cantilevers,bressummers, lintels over 1.5 mtr span complete all as specified and directed. |
| 131 | M&L for formwork to shullah hoods, chajjas, troughs and similar including edges,RCC Columns ,Piers and Posts etc rough finished surfaces of concrete flat complete all as specified and directed. |
| 132 | M/L precast cement concrete block massonry with solid blocks nexc 10 cm in width and settings in CM 1:4 type C1 1:3:6 (20mm graded aggregate) complete all as specified and directed. |
| 133 | M & L 100mm thick PCC 1:4:8 type D2 as in subfloors finished even and rough without using extra cement complete all as specified and as directed. |
| 134 | M&L for rendering 15mm thick on fair faces of brick work in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed. |
| 135 | M&L for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed. |
| 136 | M&L for wrought second class hard wood in scantlings framed and fixed complete all as specified and directed. |
| 137 | M&L for preparation of wood and wood based materials, new or old of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified and directed. |
| 138 | M&L for non skid ceremic white tiles 7 to 8mm thk area of each tile exc 0.11 sqm but n exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to mortar laid over and including15 mm thick cement screed bed in CM 1:6 complete all as specified and directed. |
| 139 | M & L for 100mm thick PCC 1:2:4 Mix, type B2 (Using 40 mm graded crushed stone aggregate) as in subfloors finished even and rough without using extra cement complete all as specified and as directed. |
| 140 | S&F Gl frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mmm c/c using GI wire of 2mm thickness GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and as directed . |
| 141 | M&L 4mm thick E Board 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer's instructions complete all as specified and directed. |
| 142 | Excavation in post holes not exceeding 0.5 cum, getting out returing, filling in and ramming earth and broken hard core/rubble mixed with earth with around the layers not exiding 25 cm each layers watering and removing surplus soil to a distance not exceeding 50 cm making good the disturbed surfaces in soil loose soil complete all as specified and directed. |
| 143 | M&L for steel work in tubular trusses incl special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed. |
| 144 | M&L for preparation of new wall surafces and applying two finishing coat of acrylic emulsion paint , anti fungal resistance , dirt resistance exterior paint of required shade including primer coat and 1 mm thk exterior putty on new surfaces complete all as specified and directed. |
| 145 | S&F in repiars stainless steel sink 1.00 mm thick for kitchen or laboratory with plug waste pipe washer , including cantilever cast iron brackets connecting union etc overall size 940mmx460mmx229mm with two bowls size 345mmx 406mm x 229 mm complete all as specified and directed. |
| 146 | M&L for preparation of new wall surafces and applying two finishing coat of acrylic emulsion paint , anti fungal resistance , dirt resistance exterior paint of required shade including primer coat complete all as specified and directed. |
| 147 | S&F 100 mm dia cast iron rain water socketed pipes with cement joint complete all as specified and directed. |
| 148 | Taking down carefully aluminium/copper conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified and directed |
| 149 | Material and labour for concealed Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, including 20 mm dia PVC conduit concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild galvanised sunken box/metal flush box made out of 1.6 mm thick galvanised sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including accessories including cutting chases and making good the disturbed surfaces as per existing for one light point controlled by one switch complete all as specified and directed. |
| 150 | All as per item No.149 above but One 3 pin 5 Amps socket out let points on independent board |
| 151 | All as per item No. 149 above but 5 Amp socket on same board with other switches. |
| 152 | Material and labour concealed point wiring for power point controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLSH cables in and including 20 mm width or higher size PVCconduit and fittings of medium grade fitted with chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. |
| 153 | Supply and fixing concealed submain wiring for DBs/ Power Point, two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC conduit (ISI marked) including 6 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade earth wire including taking down old unserviceable one complete all as specified.Note: Two runs of main wire, one run of earth wire and one run of conduit shall be measured as single unit. |
| 154 | Supply and fixing modular switch 1 way 6 A, 1 module 230/250 volt , AC supply, ISI Marked, with cover plate complete all as specified and directed. |
| 155 | Supply and fixing modular sockets 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked complete all as specified and directed. |
| 156 | Supply and fixing modular switch socket 6A 2/3 pin combined 3 module 230/250 Volts, 50 Hz , AC supply, ISI Marked complete all as specified and directed. |
| 157 | Supply and fixing modular switch socket 6/16A 6 pin combined 3 module 230/250 Volts, 50 Hz , AC supply, ISI Marked complete all as specified and directed. |
| 158 | S & F Modular cover plate with frame & flush box of 8 modules complete all as specified and directed. |
| 159 | S & F Modular cover plate with frame & flush box of 6 modules complete all as specified and directed. |
| 160 | S & F Modular cover plate with frame & flush box of 4 modules complete all as specified and directed. |
| 161 | S & F Modular cover plate with frame& flush box of 3 modules complete all as specified and directed. |
| 162 | S & F Modular cover plate with frame & flush box of 2 modulescomplete all as specified and directed. |
| 163 | Supply & fix ceiling rose surface bakelite 65 mm x 50 mm three terminal suitable for 230 Volts AC 6 Amps complete all as specified. |
| 164 | Supply and fix 18 W LED light fitting wall mounted batten 4'ft , extruded aluminium housing, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6000K including necessary connection complete all as specified and directed. |
| 165 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. |
| 166 | S & F Wall bracket decorative LED light fancy glass fitting with with lamp 9 Watt Lamp complete with necessary connection |
| 167 | Supply and fix in repair table lamp hanging type dome shaped pendant with lamp 7watt with all accessories including necessary connection and taking down old unserviceable one complete all as specified and directed. |
| 168 | Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC, 6500/3000K recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and direcetd. |
| 169 | S & F 3W surface round light 240V with necessary connections including taking down unserviceable one complete all as specified and directed. |
| 170 | S & F 12W recess/surface round light 240V with necessary connections including taking down unserviceable one complete all as specified and directed. |
| 171 | Supply & fixing in repair Garden light/LED Bollard LED lighs fitting of capacity 10 W die-cast aluminium body, 10 watt LED toughened glass complete with all accessories incl taking out old unserviceable one complete as per Comption Cat No LBLSN-10-WW type Liara or Eqv in Philips/Wipro complete all as specified and directed. |
| 172 | M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles , including necessary form work finishing even and smooth without using extra cement , complete all as specified and directed. |
| 173 | Supply and fixing/laying 40mm bore, steel tubings, galvanised, light grade with all fitting laid across road , in trenches or across PCC drain or along electric pole or floor/wall etc for protection of cable complete all as specified and as directed. |
| 174 | Supply & laying Sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable ) and gently punned down to 18cm thickness all complete as specified and as directed. Note :- Only punned down sand shall be measured. |
| 175 | M&L for fly ash bricks locally available laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed. |
| 176 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core complete all as specified and directed. |
| 177 | Supply and fix Flexible LED strips complete all as specified and direcetd . |
| 178 | Supply and fix decorative spot light 10W white/warm complete all as specified and direcetd . |
| 179 | Supply and fix Distribution board double door MCB TPN 4 way with IP 43 multiphase outgoing suitable for mounting 63 Amps MCB as incomer with Bus bars, Neutral links complete with all accessories including taking down old unserviceable one including MCBs complete all as specified and directed. |
| 180 | Supply and fix epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral 240 V, 12 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact including taking down old unserviceable one including MCBs complete all as specified and directed. |
| 181 | Supply and fix MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessary connection complete all as specified and directed. |
| 182 | Supply and fix MCB SPN 40 - 63 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessary connection all as specified and directed. |
| 183 | Supply and fix MCB TPN 63 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessary connection all as specified and directed. |
| 184 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades and frame and louvers all as specified and directed. |
| 185 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m complete all as specified and as directed. |
| 186 | Material and labour in repair for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. |
| 187 | Material and labour for concealed Point wiring with 4.0 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, including 20 mm dia PVC conduit concealed on wall/ceiling and incuding provision of 4.0 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild galvanised sunken box/metal flush box made out of 1.6 mm thick galvanised sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including accessories including cutting chases and making good the disturbed surfaces as per existing for 3 Pin, 16 Amp Switch Socket Outlet (Power Point) complete all as specified and directed. |
| 188 | S & F Switch socket outlet 3 pin 6 Amp flush type complete all as specified and directed. |
| 189 | S & F Metal flush box 3 module complete all as specified and directed. |
| 190 | S & F Metal flush box 6 module complete all as specified and directed. |
| 191 | Supply & fix lamp holder, PVC/polycarbonate type with back plate straight or angular suitable for batten fittings complete all as specified. |
| 192 | Supply and fix LED Bulb 9 Watt suitable for baten holder complete all as specified and directed. |
| 193 | Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed. |
| 194 | Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed including taking down old one. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender