Tender For special Repair Of Four Single Offrs Accn (Bldg. No P-103) In Offrs Mess Complex Under Ge (North) Bathinda At Bathinda Mil Stn
Tender Value
37.86 Lakhs
Estimated cost
Bid Submission
05 Sep 2026
13 days left
EMD
75720
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Four Single Offrs Accn (Bldg. No P-103) In Offrs Mess Complex Under Ge (North) Bathinda At Bathinda Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 500m where directed, completet all as specified and as directed. |
| 2 | Dismantling of mud roofing of any thickness, including plastering and leeping (whether full thickness removed or only part thereof), and disposal of dismantled material/rubbish to a distance not exceeding 500 m, complete as specified and as directed. |
| 3 | Water proofing treatment to existing roof/terrace using sika coolcoat /or equivalent Single component, acrylic based, flexible, micro fibre reinforced waterproofing and heat reflective coating system. the treatment shall be carried out as per the manufacturers instructions and shall include.(a) Preparation of substrate and cleaning it off all loose and triable by mechanical means(b) Open the cracks lines to form , V grooves with cutter/hammer/chisel up to 5-10mm and filling with crack filler and PU sealant.(c) application of primer coat @ 0.2 to 0.3 kg/ sqm followed by the first coat @ 0.75kg/ Sqm.(d) The second coat shall be applied @ 0.75 kg / Sqm and reinforced with fabric re-inforcement between the first and second coat.(e) The top coat of primer shall be applied after the second coat dries off @ 0.05-0.08 Kg per Sqm.(f) The material shall adhere to following specification. TECHNICAL SPECIFICATION OF MATERIALTensile Strength 1.5 MPa ASTM D412Elongation at Break > 200% ASTM D412Adhesion in Peel > 1.5 MPa (on concrete substrate) EN 1542Crack Bridging Ability Passes upto 3.2mm Width ASTM C1305Permeability to Water Vapour Passes IS 2645Water Vapour Transimission ~ 23 g/m²/24hr ASTM E96Water Absorption < 10% ( by Mass) ASTM D570Microbiological Resistance No Algae & Fungal Growth ASTM D5590Solar Reflectance Index 102 ASTM E1980.Note : Complete material shall be procured in bulk and kept in lock and key.Note : The installation company should be trained and authorized by Manufacturer & installation to be carried out as per manufacturers approved method statement. All auxiliary & accessories involved during application should be supplied by single manufacturer as a part of system. Any component used which is not manufactured by the particular manufacturer can only be used with official approval from manufacturer |
| 4 | Providing and laying Plain Cement Concrete (PCC) 1:2:4, Type B0, using 12.5 mm graded stone aggregate in roof kerbs (golla), mud stops, sides of roof sheets and similar locations, including forming rounded or chamfered edges, necessary centering, shuttering/formwork, finishing, curing and all labour, materials and incidentals complete as specified and directed by the Engineer-in-Charge. |
| 5 | Material and Labour for 15 mm thick cement rendering/plaster in CM 1:4 on roof surfaces, parapets, vertical beam surfaces and other horizontal or vertical surfaces, finished even and smooth, using only coarse sand (Toka Sand), including surface preparation, scaffolding, curing and all incidental works complete as specified and directed by the Engineer-in-Charge. |
| 6 | Making benching (gola/fillet) in PCC (1:2:4), Type B0, using 12.5 mm graded stone aggregate and incorporating waterproofing compound (WPC) as per manufacturer's instructions, along junctions of roof and adjoining walls in concave shape, including mixing, laying, finishing, curing and all labour and materials complete as specified and directed by the Engineer-in-Charge. (Note: WPC shall be measured and paid separately.) |
| 7 | Supply only liquid integral waterproofing compound conforming to relevant specifications, for use in cement concrete, mortar, plaster and allied works, complete as specified and directed by the Engineer-in-Charge. |
| 8 | Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar, including quoins, arches, pillars, etc. in any description. The work includes careful dismantling, stacking of serviceable bricks for reuse, and disposal of unserviceable materials/rubbish outside the site as directed by Engineer-in-Charge, complete all as specified and directed. |
| 9 | Brickwork with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6), including scaffolding, soaking of bricks, raking out joints, curing, and all materials, labour, tools and plants complete all as specified and directed by Engineer-in-Charge. |
| 10 | Brick work in half brick thick wall using sub class ‘B’ old size burnt clay bricks, straight or curved on plan to any radius, built in cement mortar (1:4), including scaffolding, soaking of bricks, proper bonding, raking out joints where required, curing, and all materials, labour, tools & plants complete all as specified and directed by Engineer-in-Charge. |
| 11 | Taking down cement or cement lime plaster from brick or stone walls etc., including raking out joints, hacking the surface for key, scrubbing down with water, and removing debris outside the site, complete all as specified and directed by Engineer-in-Charge. |
| 12 | Material and labour for providing 5 mm thick plastering on concrete ceiling surfaces using ready mix cement plaster material of approved make and quality, including surface preparation, scaffolding, mixing, application, levelling, finishing the surface even and fair, curing and making good, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 13 | Material and labour for providing 12 mm thick plastering on external surfaces of brick walls, chajjas, fins, or concrete surfaces using ready mix cement plaster material of approved make and quality, including surface preparation, scaffolding, mixing, application, levelling, and finishing the surface even and fair, curing and making good, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 14 | Material and labour for providing 15 mm thick plastering on external surfaces of brick walls, chajjas, fins, or concrete surfaces using ready mix cement plaster material of approved make and quality, including surface preparation, scaffolding, mixing, application, levelling, and finishing the surface even and fair, curing and making good, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 15 | Material and labour for complete removal of existing treatment of any type/description (any layer) from external/internal wall/ceiling surfaces, soffits/chajja/roof projection surfaces etc., by scraping steel patti or Mechanical sander/grinder machine having suction vaccum Bag (Smart periodical methodology), complete all as specified and as directed. |
| 16 | Material and labour for preparation of new plastered surfaces, surface after complete removal, applying acrylic putty on internal surfaces of walls/ceiling/soffits etc (thickness vary from 1.5 to 2 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using readymade putty, including sanding with wall sander after filling the putty in first coat/second coat to make surface smooth and ready for receiving interior painting complete all as specified and as directed.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order.Make of acrylic Putty: - Berger / Asian / Nerolac |
| 17 | Material and labour for applying 02 coats of interior acrylic emulsion paint of approved tint/shade (Company Depot Tinted) @ 12 sq.m/litre/2 coats to wall surfaces (new or old prepared internal surface after complete removal and applying putty) over and including a coat of interior primer @ 11 sq.m/litre/1 coat (primer shall be same make as acrylic emulsion paint), paint and primer applying by using paint roller brush complete all as specified and as directed.Note ;- Complete removal and putty shall be measured and paid separately under respective item of BOQ.Brand and Make of interior acrylic emulsion paint: - Easy Clean Matt of Berger / Apcolite Advanced of Asian / Impression Ultra Fresh of NerolacBrand and Make of interior primer: - Seal O Primer of Berger / Smart Care Primero of Asian / Excel Alkali Prime of Nerolac |
| 18 | Material and labour for applying 02 coats of exterior acrylic emulsion paint of approved tint/shade (Company Depot Tinted) @ 6 sq.m/litre/2 coats to external walls / Soffits of Chajjas / Roof Projections / Cantilevers / Balcony etc. (new or old prepared external surface after complete removal) over and including a coat of exterior primer @ 11 sq.m/litre/1 coat (primer shall be same make as acrylic emulsion paint), paint and primer applying by using airless spray gun complete all as specified and as directed.Note ;- Complete removal shall be measured and paid separately under respective item of BOQ.Brand and Make of exterior acrylic emulsion paint: - Weather Anti Dust of Berger / Apex Ultima of Asian / Excel Mica Marble of Nerolac.Brand and Make of interior primer: - Seal O Primer of Berger / Smart Care Primero of Asian / Excel Alkali Prime of Nerolac |
| 19 | Dismantling of floor, hearth, or wall tiling/terrazzo including cement mortar bedding layer but excluding backing coat, carefully removing tiles/terrazzo and bedding without damaging the base surface, preparing and cleaning the exposed surface to receive further treatment, including disposal of dismantled materials, loading, transportation, and throwing of debris in low-lying/empty area as directed at any distance up to 2.5 km from site, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 20 | Material and labour for providing 15 mm thick bedding layer (screed bed for tiles) in cement mortar (1:4) using grey cement, including mixing and incorporating liquid water proofing compound (WPC) in mortar as per manufacturer’s instructions per 50 kg bag of cement (excluding supply of WPC), laying, compacting, and finishing the surface even and fair/rough as required to receive tile work, complete in all respects, as specified and as directed by the Engineer-in-Charge.Note:(i) Liquid water proofing compound shall be deemed to be included in the rate and shall not be measured or paid separately |
| 21 | Material and labour for providing and laying 10 mm thick bedding layer (screed bed for tiles) in cement mortar (1:4) using grey cement, including mixing and incorporating liquid water proofing compound (WPC) as per manufacturer’s instructions per 50 kg bag of cement (excluding supply of WPC). The work shall include laying, compacting, and finishing the surface to a smooth even or rough texture as required to receive tile work, complete in all respects as specified and as directed by the Engineer-in-Charge.Note:(i) Liquid water proofing compound shall be deemed to be included in the rate and shall not be measured or paid separately |
| 22 | Material and labour for providing and fixing digital glazed vitrified tiles (DGVT) of approved shade, design, and pattern (including light, dark, and highlighter tiles as approved), area of each tile exceeding 0.42 sqm and not exceeding 1.0 sqm, 9–10 mm thick, premium quality, water absorption less than 0.5%, straight-edged, stain-free, glossy finish, laid in floors and skirting, set and jointed in Type-2 tile adhesive (thin bed) conforming to IS 15477:2019, including laying with 3 mm spacers or as per manufacturer’s instructions, epoxy grout filling of joints matching tile colour, surface preparation, cutting to required sizes and shapes, fixing, alignment, leveling, cleaning and finishing, complete in all respects, as specified and as directed by the Engineer-in-Charge.Note: Screed bed shall be measured and paid separately under respective item of BOQ |
| 23 | Material and labour for providing and fixing anti-skid vitrified tiles of approved shade, matte finish, coloured design, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, minimum 7 mm thick, premium quality, water absorption between 3% to 6%, straight-edged, stain-free finish, laid in floors, set and jointed in Type-2 tile adhesive (thin bed) conforming to IS 15477:2019, including surface preparation, necessary cutting to required sizes and shapes, laying, alignment, leveling, cleaning and finishing, complete in all respects, as specified and as directed by the Engineer-in-Charge.Note: Screed bed shall be measured and paid separately under respective item of BOQ |
| 24 | Material and labour for providing and fixing glazed ceramic coloured tiles of approved shade, design, and pattern (including light, dark, and highlighter tiles as approved), of premium quality, area of each tile exceeding 0.06 sqm and not exceeding 0.18 sqm, 7–8 mm thick, straight-edged, stain-free, glossy finish, water absorption between 10% to 20%, fixed on vertical surfaces such as skirting, dado, and similar works, set and jointed in approved Type-2 tile adhesive (thin bed) conforming to IS 15477:2019, including surface preparation, necessary cutting to required sizes and shapes, spacers, joint filling, cleaning, and finishing, complete in all respects, as specified and as directed by the Engineer-in-Charge.Note: Screed bed shall be measured and paid separately under respective item of BOQ |
| 25 | Demolition of stone/marble slabs of any description or thickness used in floors, cooking platforms, steps etc., including carefully breaking/dismantling, removing from bed, removing all mortar, stacking/disposing of debris outside site, and cleaning the area complete all as specified and directed by Engineer-in-Charge. |
| 26 | Material and labour for providing and fixing 18–20 mm thick machine-cut granite stone slab, factory finished with grinding and mirror polishing (table rubbed and polished), of approved colour and shade, for kitchen/cooking platform. The work shall include making required cut-outs for sink, hob, and other fixtures as and the granite slab shall be laid over 15 mm thick cement mortar bedding in CM 1:4 over grey cement slurry, properly leveled and fixed in position. Joints shall be filled with white cement (1:2) mixed with marble dust and matching pigment to suit the granite shade including machine cutting to required shape and size, edge finishing (bullnose/half-round/straight as directed), polishing, cleaning, and making good all joints. All labour, materials, tools, and incidental works required for complete execution shall be included complete all as specified and as directed by the Engineer-in-Charge. |
| 27 | Material and labour for 18–20 mm thick marble stone slab of any black or mahroon colour, machine cut, factory finished (other than table rubbed and polished), for use in counter sunk wash basin, steps, jambs, pillars, window sills, cooking platforms and similar locations, including setting and fixing in position over 15 mm thick cement mortar bedding in CM 1:4. The work shall include laying over grey cement slurry, pointing in white cement (1:2) mixed with marble dust and pigment to match the shade of marble slab, machine cutting to required shape (square/rectangular or as per site requirement), edge finishing, cleaning, and extra polishing if required complete all as specified and as directed by the Engineer-in-Charge.\\" |
| 28 | Material and labour for 18–20 mm thick marble stone slab of any black or mahroon colour, machine cut, factory finished (other than table rubbed and polished), for skirting, dado, risers and similar vertical applications, including fixing in position over 10 mm thick rendering in cement mortar (1:4). The work shall include laying over cement slurry, cutting to required size and shape (square/rectangular or as per site requirement), edge finishing, pointing in white cement (1:2) mixed with marble dust and pigment to match the shade of marble slab, cleaning, and making good joints. All materials, labour, tools and incidental works required for complete execution shall be included complete all as specified and as directed by the Engineer-in-Charge.\\" |
| 29 | Material and labour for providing and laying 10 mm thick coloured paver tiles (Endura Tiles) of size 300 × 300 mm, over and including 20 mm thick cement mortar bedding in CM 1:4, laying tiles to proper level and line, including filling of joints with coloured cement to match existing surface, cutting of tiles wherever required, proper curing, cleaning and finishing complete all as specified and directed by Engineer-in-Charge. |
| 30 | Surface excavation not exceeding 30 cm in depth and averaging 15 cm depth, including getting out soft/loose soil, levelling and dressing of surface, stacking or disposal of excavated material as directed, complete all as specified and directed by Engineer-in-Charge. |
| 31 | Material and labour for providing and laying 75 mm thick cement concrete type B-2, 1:2:4 (using 40 mm graded stone aggregate) as in sub-base, including mixing, laying, compacting, levelling to required slope/level, finishing surface, curing and all necessary operations complete all as specified and directed by Engineer-in-Charge. |
| 32 | Supply and fixing of 60 mm thick (M-35 grade) precast interlocking concrete paver blocks, factory made using PVC/Rubber moulds on vibrating table machine, using grey cement without pigment, of approved shape such as hexagon / triangular / zigzag / I-shape or as directed by Engineer-in-Charge, prepolished and preglazed, conforming to relevant IS specifications, having minimum compressive strength of 350 kg/sqcm, laid over and including 30 mm thick sand cushioning layer, properly compacted, levelled and finished, including filling of joints/interstices with fine sand, cutting wherever required, compaction and all other necessary operations complete all as specified and directed by Engineer-in-Charge. |
| 33 | Demolition of reinforced cement concrete (RCC) of roof slabs (other than ground floor), beams, staircases, landings, chajjas and similar suspended RCC works, including cutting of reinforcement bars as required to facilitate demolition, breaking RCC into manageable pieces, stacking and removing debris outside site premises, complete disposal, and cleaning of site area, all as specified and directed by Engineer-in-Charge. |
| 34 | Material and labour for reinforced cement concrete (RCC) 1:2:4, Type B-0 (using 12.5 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs, shelves and similar works, including formwork, mixing, placing, vibrating, compacting, finishing the top surface, curing and all necessary operations complete all as specified and directed by Engineer-in-Charge. Note :- Reinforcement steel shall be measured and paid separately. |
| 35 | Material and labour for reinforced cement concrete (RCC) 1:2:4, Type B-0 (using 12.5 mm graded stone aggregate) as in fins, fascias, louvers, parapets, railings exceeding 60 cm in height, balustrades and similar architectural elements, including formwork, centering, mixing, placing, vibrating, compacting, finishing, curing and all necessary operations complete all as specified and directed by Engineer-in-Charge.Note :- Reinforcement steel shall be measured and paid separately. |
| 36 | Use and waste of formwork to sides and soffits of floor or roof beams, roof slabs, cantilevers, shelves and similar RCC works, providing rough finished surface, including all necessary staging, shuttering, supports, removal after completion, cleaning and making good as required, complete all as specified and directed by Engineer-in-Charge. |
| 37 | Use and waste of formwork to sides and soffits of fins, louvers, fascia and similar RCC architectural elements, providing rough finished surface, including all staging, shuttering, supports, proper alignment and line, removal after completion of RCC work, cleaning and making good as required, complete all as specified and directed by Engineer-in-Charge. |
| 38 | Material and labour for providing and fixing Mild Steel TMT bars Fe-550D, 10 mm dia and above, cut to required lengths, bent to shape, including cranking, bending, spirally bending for hooping of columns, forming hooks at ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, including making of rungs, handles, etc., complete all as specified and directed by the Engineer-in-Charge. (Note: Weight of binding wire shall not be considered for measurement and payment purpose.) |
| 39 | Material and labour for providing and fixing Mild Steel TMT bars Fe-550D, 6 to 8 mm dia, cut to required lengths, bent to shape, including cranking, bending, spirally bending for hooping of columns, forming hooks at ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, including making of rungs, handles, etc., complete all as specified and directed by the Engineer-in-Charge. (Note: Weight of binding wire shall not be considered for measurement and payment purpose.) |
| 40 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast as required complete all as specified and as directed. |
| 41 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast as required complete all as specified and as directed. |
| 42 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door & other Frames/Chowkhat (Single Rebated) of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 43 | Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door & other Frames/ Chowkhat (double Rebated) of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed.Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 44 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges of size 100mm - 4 nos. per leaf (Table 6 of BIS 12817-2020) BIS marked. (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf as per table 1, dia of bolt 12mm as per BIS 15833. (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding door Bolt 300 mm - 1 no. per leaf, 16mm dia as per BIS marked clause 3(iii) of BIS 15834-2020. |
| 45 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) glazed/gauge skelton door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with butt hinges with necessary full body threaded star headed counter sunk S.S screws including S&F wire cloth complete all as specified and as directed including supply and fixing following items:-(a) Stainless Steel (304 Grade) Finished Butt Hinges of size 100mm - 4 nos. per leaf (Table 6 of BIS 12817-2020) BIS marked. (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf as per table 1, dia of bolt 12mm as per BIS 15833. (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding door Bolt 300 mm - 1 no. per leaf, 16mm dia as per BIS marked clause 3(iii) of BIS 15834-2020. (e) Stainless Steel (304 Grade) (natural finish) wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm, fixing as per manufacture |
| 46 | Note for WPC Frame/shutter (items above)(i) Test certificate of Manufacturer to be provided by contractor.(ii) Embossing with Barcode of Manufacturer engraved over each door Frame & shutter is mandatory. (iii) Cost for making good to cutting holes/dismantled portion during taking down old with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate or cement mortar (1:3) shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. (iv) The cost of all other connected accessories, fixing material shall deemed to be included in the quoted unit rate. |
| 47 | Supply & fixing powder coated aluminium anodised frame for door/window/ventilator /partition , made out of aluminium section / aluminium chanel, powder coated (minimum thickness of powder coating not less than 50 micron), for doors, windows, ventilators with one or more rebate including jointing cleat for fixing etc. including taking down old unserviceable frame complete all as specified and as directed by Engineer-in-Charge.Note :- Weight of aluminium section/aluminium channel shall be physically ascertained through a board of officers convened by Accepting officer and payment shall be made only after the actual weight at site. |
| 48 | Material and labour for providing and fixing aluminium work for shutters of doors, windows, ventilators and partitions with polyester powder-coated aluminium sections (minimum polyester powder coating thickness 50 microns), using extruded built-up standard tubular sections, appropriate Z-sections and other approved aluminium sections of approved make. The work shall include fixing with dash fasteners of required diameter and size, filling of gaps at top, bottom and sides with EPDM rubber/neoprene gaskets, and all necessary accessories. The aluminium sections shall be smooth, straight, rust-free, accurately mitred and mechanically jointed wherever required, including aluminium cleat angles, aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws, handles, sliding bolts, tower bolts, door stoppers and all fittings complete, complete in all respects as specified and as directed by the Engineer-in-Charge. |
| 49 | Notes:(a) The rate shall include the cost of EPDM rubber/neoprene gaskets, C.P. brass/stainless steel screws and all fixing accessories. Nothing extra shall be paid on this account.(b) For measurement and payment, only the weight of aluminium sections, aluminium cleat angles and aluminium snap beading shall be considered. The weight of EPDM rubber/neoprene gaskets, C.P. brass/stainless steel screws and other accessories shall not be considered for measurement and payment.(c) Glazing/panelling shall be measured and paid for separately. |
| 50 | Supply and fixing 5.5 mm thick ordinary quality sheet glass of any size and shape, cut to required dimensions and fixed in position with oil putty, including bedding, pointing, fitting, wastage, cleaning and all necessary materials and labour, complete all as specified and directed by Engineer-in-Charge. |
| 51 | Supply and fixing 25 micron thick reflective type solar control film (Greater Sun Control or equivalent approved make) on existing glass surfaces, including surface preparation, cleaning of glass, cutting to required size, application of film without wrinkles, bubbles or defects, trimming of edges, and all necessary materials, labour, tools and accessories, complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply and fixing hydraulic door closer, pelmet arm type with PVD (Physical Vapour Deposition) cover, overhead mounted door closer of approved make and quality, having minimum 130° door opening angle, adjustable closing and latching speed, suitable for doors weighing up to 85 kg and door widths from 800 mm to 1200 mm, manufactured from commercial-grade aluminium alloy, weather-proof and rust-resistant finish, including removal of existing door closer, fixing with all necessary screws, brackets, accessories, testing, adjustment and commissioning, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 53 | Supply and fixing in repair floor door stopper, 150 mm size, comprising aluminium alloy body and tongue, anodised finish, with hard drawn steel spring, fixed securely to floor including all necessary screws, fittings, making good disturbed surfaces and all labour, complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply and fixing stainless steel wire cloth of 0.56 mm nominal diameter wire and average aperture width of 1.18 mm, fixed with stainless steel/tinned tacks or stainless steel wire staples as approved, including cutting to size, fixing in position and all necessary materials and labour, complete all as specified and directed by Engineer-in-Charge. |
| 55 | Material and labour for preparation of old painted steel surfaces of any description exceeding 10 cm width or girth, by cleaning off dust, dirt and loose particles using sand paper, clean cloths and dry paint brushes, and applying one coat of first quality synthetic enamel paint of approved colour/tint to obtain a smooth glossy finish, including all materials, labour, tools and accessories, complete all as specified and directed by Engineer-in-Charge. |
| 56 | Demolition of unreinforced cement concrete and excavation in sunken floor area of any description and in any position, including breaking up and removal of existing cement concrete, digging out as required, disposal of dismantled material, loading, transportation, and throwing of debris in low-lying/empty area as directed at any distance from the site, including cleaning of area and making safe the surrounding surfaces, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 57 | Waterproofing treatment to sunken floor using acrylic based multipurpose polymer. The treatment shall be carried out as per manufactures specification. The treatment shall be include (i) Surface preparation of substrate by removing all traces of contaminates, loose and friable particles, cement laitance oils and grease, water repellent coatings etc(ii) Injection grouting using cementitious grout if required. The payment for injection grouting shall be made separately etc(iii) Repair to the substrate, filling of blow holes/voids and surface leveling using appropriate products specified by the manufacture.(iv) All intersections of horizontal and vertical surface should be profiled with a mortar fillet of minimum 25mm x 25mm.(v) The moisture content of the substrate shall be checked before application of first coat at water proof coating at the rate of 200 g/m2 followed brush topping at 450g/m2 per mm. The second coat shall be reinforced with glass fabric between the first and second coat.(vi) The treatment shall be protected by application of polymer modified cement mortar of thickness 10mm applied at the rate of 50g per mm.(vii) Tech specification :- Tensile adhesion strength :- 0.5N/mm2(as bonding slurry)Make : Sikka, Raintite or equivalent |
| 58 | Material and labour for providing Plain Cement Concrete (PCC) 1:5:10, Type E-2, using 40 mm graded aggregate with AAC sludge/bats as filler material, for filling in sunken floors, including preparation of surface, placing and compacting concrete in layers as required, leveling and finishing to required levels and slopes, curing, and making good, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 59 | Supply and fixing 110 mm bore PVC (SWR) Type-B pipe, single socketed, in any length, conforming to relevant specifications, with rubber ring joints, fixed to walls with GI brackets/clamps at a distance of 100–120 mm from the wall, including all fittings, jointing materials, cutting and making connections, taking down existing pipe of any type and description, removing debris, testing for proper flow and leakage, complete all as specified and directed by Engineer-in-Charge. |
| 60 | Supply and fixing 110 mm bore PVC (SWR) Type-B pipe, single socketed, in any length, of approved make (Astral / Prince / Finolex), laid on floor or in trenches, including jointing, cutting, fitting, necessary specials and connections, dismantling/taking down existing pipe of any type and description, removal of unserviceable material, and making good disturbed surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply and fixing 110 mm bore uPVC (SWR) Type-B bends of any radius and/or shoe, of approved make (Astral / Prince / Finolex), fixed to PVC (SWR) pipes, including rubber ring jointing, cutting, fitting, necessary fittings, supports, testing and all labour and materials required for proper installation, complete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply and fixing 110 mm dia long neck uPVC SWR floor trap with grating, including jointing to waste pipe, fixing in cement concrete 1:2:4 Type B-1 in repair, including dismantling of existing trap if required, making good disturbed surfaces, testing for leakage and proper flow, complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply and fixing 110 mm dia long neck uPVC SWR P-trap with grating, including jointing to waste pipe, fixing in cement concrete 1:2:4 Type B-1 in repair, including dismantling of existing trap if required, making good disturbed surfaces, testing for leakage and proper flow, complete all as specified and directed by Engineer-in-Charge. |
| 64 | Supply and fixing uPVC SWR branch pieces, 110 mm bore, single socketed, equal or unequal type (Y, T, etc.), for soil/waste pipe work in repairs, including rubber ring jointing, cutting, fitting, connection to existing pipe line, dismantling of old fittings if required, testing for leakage and proper flow, complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply and fixing 75 mm bore uPVC (SWR) Type-B pipe, single socketed, in any length, laid on floor or in trenches, including rubber ring jointing and/or cement mortar jointing as required, cutting, fitting and necessary connections, dismantling and taking down existing pipe of any type and description, removal of debris, testing for leakage and proper flow, complete all as specified and directed by Engineer-in-Charge. |
| 66 | Supply and fixing 75 mm dia uPVC (SWR) bends of any radius with access door/cleaning door, including rubber ring jointing, cutting, fitting and connection to existing uPVC (SWR) pipeline, making proper alignment and slope, testing for leakage and proper flow, complete all as specified and directed by Engineer-in-Charge. |
| 67 | Supply and fixing 75 mm dia uPVC (SWR) branch piece single (Y-type), equal or unequal, with access/cleaning door, including rubber ring jointing, cutting, fitting and connection to existing SWR pipeline, proper alignment and slope, testing for leakage and proper flow, complete all as specified and directed by Engineer-in-Charge. |
| 68 | Supply and fixing 75 mm dia uPVC (SWR) junction single (T-single), equal or unequal, with access/cleaning door, including rubber ring jointing, cutting, fitting and connection to existing SWR pipeline, proper alignment and slope, testing for leakage and proper flow, complete all as specified and directed by Engineer-in-Charge. |
| 69 | Supply and fixing 20 mm dia CPVC pipe SDR-11 along with CPVC SDR-11 plain fittings, including all fittings and accessories, fixing to walls and ceilings or laying in floors as required, including cutting, threading/solvent jointing, proper clamping/supports, testing for leakage and commissioning, and taking down existing GI tubing of any size and description, complete all as specified and directed by Engineer-in-Charge. |
| 70 | Cutting chases in brick/stone masonry and concrete surfaces, pinning in, and making good to facings where required with cement mortar 1:3, including pointing to ends or edges of landings, steps, window cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring and making good disturbed surfaces, cutting not exceeding 10 cm girth, complete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply and fixing vitreous china premium/first quality wall hung water closet (WC) of P-trap type in white/ivory/off-white shade, including connection to soil/waste drain outlet, flushing pipe, antisyphonage pipe, etc., complete. The item shall include supply and fixing of plastic soft-close seat cover as recommended by the manufacturer for the particular model (closed pattern with flat bottom), all fixing accessories, installation kit, and ‘S’ type drain pipe connection set suitable for wall-hung WC, complete in all respects. The work shall further include supply and fixing of concealed PVC flushing cistern of 8 litre capacity with dual flushing system, valveless syphonic action type, complete with inlet/outlet fittings, ball valve, float valve, brackets, and all necessary pipe connections. The item shall also include supply and fixing of actuator knob/flush plate as per manufacturer’s recommendation. The scope includes supply and fixing of all necessary accessories such as rag bolts, gel gasket, hinges, and SS jet spray with 1 metre long PVC pipe and CP connector, complete. The item also includes dismantling and removal of existing water closet of any description/size (surface mounted or otherwise), making good disturbed surfaces, and all incidental works required for proper installation.All work shall be complete in all respects as specified and as directed by the Engineer-in-Charge. |
| 72 | Supply & fixing vitreous china wash hand basin oval type under counter, white colour, of size 595mm x 420mm x 200mm excluding taps, but including fancy type 32mm waste coupling and waste pipe, fixing/counter sunked in granite slab, complete all as specified and as directed by Engineer-in-Charge.Note :- Granite slab shall be measured and paid separately under appropriate item of BOQ.Make :- Cat Part CNS-WHT-705 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II |
| 73 | Supply and fixing in replacement PVC Bathroom mirror cabinet of appx size 450mm X 350mm X 140mm / 450mm X 380mm X 140mm (Compact Mirror Cabinet, Concealed shelves) approved quality complete all as specified and as directed. |
| 74 | Supply & fixing in replacement stainless steel sink, AISI 304 quality grade, made out of 1.20mm thick sheet, glossy finish, for kitchen or laboratory, with plugs, washers, waste coupling, waste pipe (flexible) 800mm long, including bedding in cement mortar to dwarf wall or fixing cast iron cantilever brackets and connecting union to waste pipe; overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm and making good disturbed portion in CM 1:3 or PCC 1:2:4 complete all as specified and as directed. |
| 75 | Supply and fixing rotational moulded polyethylene double-layer water storage tank (vertical cylindrical, closed top), conforming to IS 12701:1996, white in colour or as directed, of 1000 litres capacity, hoisted and fixed in position, including making inlet and outlet connections, complete. The rate shall include 20 mm bore PTMT ball valve of high-pressure type with epoxy-coated aluminium rod and high-density plastic ball (polyethylene float), suitable for 20 mm bore iron pipe, gate valve, float valve, all fittings, labour, and incidental works. The item shall also include dismantling/taking down and disposal of existing unserviceable PVC water storage tanks exceeding 500 litres but not exceeding 1000 litres capacity, complete in all respects as specified and as directed by the Engineer-in-Charge. |
| 76 | Supply and fixing in replacement of 600 mm long PVC connection pipe, 15 mm nominal size, with PTMT nuts, complete in all respects as specified and as directed by the Engineer-in-Charge. |
| 77 | Supply and fixing bib tap, chromium plated (CP), with wall flange, screwed type, suitable for 15 mm bore brass ferrule connection, fixed in position with necessary accessories, including making connections, sealing, testing for leakage and smooth operation, complete in all respects, as specified and as directed by the Engineer-in-Charge.Make: Jaquar (Cat No. VGP-81037) (VIGNETTE Prime) or equivalent from Cera (Valentina Single Lever Series) or equivalent from Hindware (Fluid Series) or techno-commercial equivalent as approved in Appendix ‘B’ |
| 78 | Supply and fixing in replacement single lever sink mixer with swinging spout, with connecting legs and wall flanges, wall mounted fancy type, chromium plated (CP), screwed down type, high pressure suitable, with screwed ends suitable for 15 mm bore iron (GI) pipe or union connection, of approved quality and make, including necessary fittings, sealing materials, fixing in position, making connections to existing pipeline, testing for leak-proof operation and smooth functioning, complete in all respects, as specified and as directed by the Engineer-in-Charge.Make : Jaquar Cat No. VGP-81165 or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 79 | Supply and fixing in replacement single lever wall mixer with provision for overhead shower, complete with 115 mm long bend pipe on upper side, connecting legs and wall flanges, wall mounted type, screwed down suitable for connection to iron (GI) pipe, of approved quality and make, including necessary fittings, sealing materials, fixing in position, making connections to existing pipeline, testing for leak-proof operation and smooth functioning, complete in all respects, as specified and as directed by the Engineer-in-Charge. Make : Jaquar (Cat No. ORP-10117PM) or equivalent from Hindware (Fluid Series) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 80 | Supply and fixing in replacement central hole basin mixer valve with regular spout, 15 mm bore, brass chromium plated (CP), suitable for mixing hot and cold water, complete with necessary fittings, including 450 mm long braided flexible hoses with connectors and nuts suitable for wall hung basin (WHB), fixed in position with proper alignment, sealing, testing for leakage and smooth operation, complete in all respects, as specified and as directed by the Engineer-in-Charge.Make: Jaquar (Cat No. CQT-CHR-23167B) or techno-commercial equivalent as mentioned in Appendix ‘B’ |
| 81 | Supply and fixing in replacement of hand shower (health faucet) with ABS body, complete with 1.0 metre long, 8 mm diameter flexible tube and wall hook, including taking down/removing the existing hand shower of any type, and fixing the new health faucet complete in all respects as specified and as directed by the Engineer-in-Charge. |
| 82 | Supply and fixing in replacement sheet glass corner shelf assembly of size 300 x 300 mm / 250 x 250 mm for corners, consisting of 5.5 mm thick clear sheet glass shelf with bevelled and/or polished edges, fixed with stainless steel ‘D’ brackets and railing/support system of approved quality, including removal of existing damaged corner shelf (if any), providing necessary fixing accessories, drilling and plugging in wall, proper alignment, fixing in position, and ensuring firm support and stability, complete in all respects, as specified and as directed by the Engineer-in-Charge.Cat part No ACN-1173 of Jaquar or Techno commercial equivalent in make mentioned in Appx 'B' |
| 83 | Supply and fixing angular stop cock with wall flange, chromium plated (CP), screwed down type, suitable for 15 mm bore brass ferrule or union connection, fixed in position with necessary accessories, including making connections to existing pipe line, sealing, testing for leakage and smooth operation, complete in all respects, as specified and as directed by the Engineer-in-Charge.Make: Jaquar (Cat No. VGP-81053) or techno-commercial equivalent as mentioned in Appendix ‘B’ |
| 84 | Supply and fixing in repair stop valve, fancy type, chromium plated (CP), with long shank and cup (concealed type), including exposed part kit with wall flange and regular concealed stop cock body, suitable for 15 mm line, complete with protection cap, fixed in position with necessary accessories, making connections to existing pipe line, sealing, testing for leakage and smooth operation, complete in all respects, as specified and as directed by the Engineer-in-Charge.Make: Jaquar (Cat No. VGP-81083K & ALD 083) or techno-commercial equivalent as mentioned in Appendix ‘B’ |
| 85 | Supply and fixing overhead shower 100 mm round shape, single flow type, ABS body, chromium plated with grey face plate, provided with Rubit cleaning system, including shower arm 450 mm long, 20 mm dia, round shape, wall mounted type with 90° bend and wall flange, fixed in position with proper alignment, sealing, testing for leakage and smooth operation, complete in all respects, as specified and as directed by the Engineer-in-Charge.Make: Jaquar (Shower-OHS-1989, Shower Arm-SHA-479L450) or techno-commercial equivalent as mentioned in Appendix ‘B’ |
| 86 | Supply and fixing in replacement of gun metal globe valve or gate valve, ISI marked, manufactured from brass cast copper alloy with iron wheel head, screwed at both ends and suitable for 20 mm bore iron pipes, complete in all respects, including taking down/removal of the existing valve, as specified and as directed by the Engineer-in-Charge.Note: The minimum weight of the gate valve shall conform to the requirements specified in the Schedule of Rates (SSR) or the relevant Indian Standard (IS). |
| 87 | Supply and fixing in replacement of gun metal globe valve or gate valve, ISI marked, manufactured from brass cast copper alloy with iron wheel head, screwed at both ends and suitable for 15 mm bore iron pipes, complete in all respects, including taking down/removal of the existing valve, as specified and as directed by the Engineer-in-Charge.Note: The minimum weight of the gate valve shall conform to the requirements specified in the Schedule of Rates (SSR) or the relevant Indian Standard (IS). |
| 88 | Supply and fixing in replacement stainless steel grating of 100–125 mm dia, with or without waste hole as required at site, of approved quality and finish, including removal of existing damaged grating, providing necessary sealing and fixing arrangement, fixing in position in floor/wall drain outlet, ensuring proper alignment and smooth discharge of water, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 89 | Supply and fixing in repairs stainless steel curtain rod of 25 mm dia, including brackets and holders made out of stainless steel sheet of grade X02Cr19Ni10 (304 S2), with surface finish No. 4 conforming to IS 6911:2017, of approved quality, including removal of existing damaged curtain rod, fixing in position with necessary screws, rawl plugs and accessories, ensuring proper alignment, firm support and smooth installation, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 90 | Supply and fixing in replacement of stainless steel (SS) soap dish of approved quality and standard size, suitable for accommodating soap, toothbrush, and toothpaste, including necessary fixing accessories, removal of existing damaged soap dish, drilling and plugging of wall as required, and fixing in proper position with correct alignment and firm support, ensuring stable installation, complete in all respects, as specified and as directed by the Engineer-in-Charge. |
| 91 | Dismantling of wall and ceiling boards (fibre board, pulp board, insulation board, etc.) or insulation slabs/blankets of any thickness, including cover fillets and all associated fixtures, complete, as specified and as directed by the Engineer-in-Charge. |
| 92 | Material and labour for PVC sheet wall paneling of thickness 5 mm (±0.25 mm) consisting of panels of desired size stuck on inner framework of 50 mm wide strips of 5 mm (±0.25 mm) thick Prelam PVC sheet. The panel & strips shall be sheet of Density 600 kg per cum. The strips should have in their center a grove of 6 mm width and 1 mm depth for sinking the head of the screw used to fix the strips to the wall vertically at an equal interval of 255 mm between two PVC strips. The PVC strips shall be fixed to the wall using 65 mm long mild steel screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200 mm. A groove of 2 mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a Strips of 5 mm (±0.25 mm) thick PVC sheet of width 75 mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement complete all as specified and as directed. |
| 93 | Supply and fixing of mild steel cupboard shutters, double-leaf type, with frame fabricated from 20-gauge MS sheet and shutter leaves fabricated from 21-gauge MS sheet, conforming to Godrej pattern or equivalent approved design. The shutters shall be provided with a three-way locking arrangement, brass dead lock, chromium-plated (CP) handle, and duplicate keys. The item shall include surface preparation, one coat of red oxide primer, and two coats of spray painting of approved shade. The shutters shall be fixed to the existing cupboard with all necessary nuts, bolts, hinges, and fasteners, including embedding portions in PCC (1:2:4) where required, complete in all respects as specified and as directed by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 94 | Supply and fixing of mild steel cupboard shutters, double-leaf type, with frame fabricated from 20-gauge MS sheet and shutter leaves fabricated from 21-gauge MS sheet, conforming to Godrej pattern or equivalent approved design. The shutters shall be provided with a three-way locking arrangement, brass dead lock, chromium-plated (CP) handle, and duplicate keys. The item shall include surface preparation, one coat of red oxide primer, and two coats of spray painting of approved shade. The shutters shall be fixed to the existing cupboard with all necessary nuts, bolts, hinges, and fasteners, including embedding portions in PCC (1:2:4) where required, complete in all respects as specified and as directed by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender