Tender For Special Repair To Bldg No T-50 At Pc Coy, Beg And Centre Roorkee Under Ge Roorkee
Tender Value
Ref. Documents
Estimated cost
Bid Submission
11 Sep 2026
18 days left
EMD
87900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Haridwar → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No T-50 At Pc Coy, Beg And Centre Roorkee Under Ge Roorkee
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of concrete (Un-reinforced) including stone slabs etc in ground floor and paving etc in n exc 15 cm thick below or above GL complete all as specified and directed. |
| 2 | Demolition of reinforced concrete any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 3 | M&L for 75mm thick PCC (1:3:6) type C-1 (using 20 mm graded aggregate) as in plinth protection, floor etc, laid in panels not exc 1.80 sqm each and filled with mastic fillig of bituman and sand all specified,finished even and smooth without using extra cement complete all as specified and directed. |
| 4 | M&L PCC (1:4:8) type D-2 (using 40 mm graded aggregate) as in sub base of floors levelling coarse complete all as specified and directed. |
| 5 | M&L 25mm thick Cement concrete type B-0, (1:2:4) (12.5mm graded aggregate) as in floor complete all as specified and directed. |
| 6 | Demolition of concrete in roofs, floor (other than ground floor), chajjas and other similar suspended work complete all as specified and directed . |
| 7 | M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in cills, coping, bed plates, bed blocks for hold fasts, apex stones and the like with plain fair faces including weathering, slightly rounded or chamfered angles and throating and necessary form work complete all as specified and directed. |
| 8 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 9 | M&L for Reinforced cement concrete Type B1 (1:2:4) (20 mm graded aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 10 | Use and waste for Fair finished formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed. |
| 11 | M&L for brick work in CM 1:6 using Sub class ‘B’ Bricks straight or curved on plan exc 6 m mean radius complete all as specified and directed. |
| 12 | M&L for brick work in CM 1:4 using Sub class ‘B’ Bricks straight or curved on plan any radius in half brick complete all as specified and directed. |
| 13 | M&L for precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) in manhole covers including necessary form work and fixing in position in cement mortar (1:4) complete all as specified and directed. |
| 14 | M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps,jambs, pillars, window- cills, cooking platforms over and incl 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of edges where required complete all as specified and directed. |
| 15 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required ,including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed . |
| 16 | M&L for Mild steel TMT bars but 5mm dia and over upto and 10mm dia in stirrups, spacers, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 17 | S&F in repair hollow PVC wall lining consisting of PVC panels not less than 5 mm thick with one side pre-laminated decorative finish having PVC sheet thickness not less than 0.6 mm thick, fixed to wall complete all as specified and directed. |
| 18 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) not exc 1.5 Sqm each including necessary cutting holes and making good using PCC (1:2:4) Ty B-0 complete all as specified and directed . |
| 19 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) exc 1.5 Sqm but n exc 4 Sqm each including necessary cutting holes and making good using PCC (1:2:4) Ty B-0 complete all as specified and directed. |
| 20 | S&F Powder coated anodised aluminium frame wt @0.55Kg/mt for doors, windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 21 | S&F, Powder Coated aluminium door shutters, having top rail of size 101.60mm x 44.50x2.50mm, Middle rail of size 101.60mm x 44.50x2.0 mm, bottom rail of size 150.00mmx 44.50x2.20 mm and side vertical rail of size 83.50mmx44.50x1.80 mm aluminium section including necessary joining cleats, glazing clips, rubber neoprene packing, 2 Nos powder coated handles 200mm long in each door, 200mm long powder coated tower bolt, hinges,motice lock, powder coated anodised aluminium snap beading screws etc complete all as specified and directed. |
| 22 | S&F for Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, 4mm thick plain glass, Powder coated aluminium fittings such as, hinges 100mm long (2 no.), suitable handle (1no.) and 100mm long tower bolt (2 No) in each shutter complete all as specified and directed. |
| 23 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, in the frame at site as per specification & drawing complete all as specified and directed. |
| 24 | S&F Factory made single extruded WPC (Wood) Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 25 | S&F Powder Coated anodised aluminium grill of 50x50x5mm size (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. |
| 26 | S&F sheet glass 5.5 mm thick ordinary quality and glazing with neoprene beading to aluminium frame complete exc 0.5 sqm in each pane complete all as specified and directed. |
| 27 | S&F sheet glass 5.00 mm thick ordinary quality and glazing with neoprene beading to aluminium frame complete n exc 0.5 sqm in each pane complete all as specified and directed. |
| 28 | S&F factory made WPC single extruded 100% lead free ROHS certified board of 9 mm thick pre-laminated shutter for aluminium door, kitchen cupboard,room cupboard and bathhroom cupboard. The laminated shutter should be 12 microne pre mainated side with different design density not less than 650Kg/cum manufactured by an ISO 9001:2015 certified company fixed with screws to timber/aluminium frame work complete all as specified and directed. |
| 29 | M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of steel, other parts made of mild steel heavy duty and fixed complete all as specified and directed. |
| 30 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 31 | M&L vitrified ceramic light shade tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed. |
| 32 | -Ditto- but as in skirting over 15mm thick rendering in CM (1:4), complete all as specified and directed. |
| 33 | M&L for glazed ceramic colour joint free tiles in vertical surface size 450x350x7mm/450x300x7mm/ 600x300mmx7mm thick as required set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:4) complete all as specified and directed. |
| 34 | M&L for Non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed. |
| 35 | M&L Udaipur green (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over and incl 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of edges where required complete all as specified and directed. |
| 36 | Taking down cement plaster (including tiles, if necessary) of any description on Brick walls including racking out Joints, hacking for key scrubbing down with water etc complete all as specified and directed. |
| 37 | M&L for rendering 15 mm thick in CM (1:6) on Brick surfaces, rendering is to be finished even and smooth (without using extra lime or cement) complete all as specified and directed. |
| 38 | M&L for rendering 15mm thick consisting of two coats, top layer 5 mm thick in CM 1:4 (mixed with WPC) over 10mm thick layer in CM 1:6, on fair faces of brick work (WPC shall be measured & paid separately) finished even & fair all as specified. |
| 39 | Supply only Liquid water proofing compound complete all as specified and directed. |
| 40 | M&L for complete removal of existing treatment on surfaces of walls by scrapping down with mechanical grinder on old walls as per the specification of manufacturers instructions of paints/OBD complete all as specified and directed. |
| 41 | M&L applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10sqm complete all as specified and directed. |
| 42 | M&L applying with 2 coat of oil bound distemper over a coat of 1mm thick putty on wall, complete all as specified and directed. |
| 43 | Dismantling timber scantlings 40 sq cm and over in section, in any position, framed work. |
| 44 | M&L for rolled mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-410-W (Gde E-250) complete all as specified and directed. |
| 45 | M&L for mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W (Gde E-250) complete all as specified and directed. |
| 46 | M&L for mild steel bolts of dia 16mm purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and directed. |
| 47 | M&L preparation new steel surface over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 48 | Taking down asbestos (corrugated, semi-corrugated etc) sheets in roof covering complete all as specified and directed. |
| 49 | S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick AZ-150 of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 50 | S&F Prepainted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick AZ-150 of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 51 | Providing and fixing tiled false ceiling of designer tiles (high pressure steam Cured) of 4mm thickness of size 595x595mm (Cascade or Electra or equivalent), suspended on inner locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams, both side inclusive and black painted groove on all T webs) consisting of main “T” runner with suitably spaced joints to get required length and 15x32mm made from 0.3mm thick sheet, 1200mm long spaced between main “T” at 600mm C/C to form a grid of 1200x600mm and secondly cross “T” of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of 1200x600mm panel to form grids of 600x600mm and wall angle 15x20x0.36mm and laying false ceiling tiles in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling/truss using GI soffit cleats fixed to existing RCC lintel/truss with dash fasteners, GI adjustable rods of 3mm dia with galvanized butterfly level clips, spaced at 1200mm c/c along main “T”, bottom exposed width of 15mm of all “T” sections shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5 mm width, all complete at all heights complete all as specified and directed . |
| 52 | S&F 25 mm dia steel fancy type CP curtain rod with and including steel type brackets, stops, of suitable size & side caps etc. complete all as specified and directed. |
| 53 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store. |
| 54 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store. |
| 55 | S&F 15mm bore GI steel tubing medium grade with all fitting and fixed complete to walls and ceilings or laid in floors including cutting chases and filling with CM (1:3) if necessary complete all as specified and directed. |
| 56 | S&F 20mm bore GI steel tubing medium grade with all fitting and fixed complete to walls and ceilings or laid in floors including cutting chases and filling with CM (1:3) complete all as specified and directed. |
| 57 | S&F in repair for Vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) including necessary fixing bolts, 'P' or 'S' trap with white seat cover complete all as specified and directed. |
| 58 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 59 | S&F in repair PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float ,handle and PVC. 32 mm dia flush pipe including brackets of 10 Ltr capacity complete all as specified and directed. |
| 60 | S&F in repair vitreous china counter wash basin, white, Oval type, size 550x400mm, excluding taps, chain and plug and porcelain stopper but including waste coupling, exclusive of fixing of supply and waste pipe fixing complete all as specified and directed. |
| 61 | S&F in repair vitreous china pedestal type wash basin, white, Oval type, size 630x450mm, excluding taps, chain and plug and porcelain stopper but including waste coupling, brackets including cutting and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe fixing complete all as specified and directed. |
| 62 | S&F in repairs, 15mm dia bore brass CP mixer (Central hole basin mixer with 450mm long braided hoses) for mixing hot & cold water screwed down for iron pipe complete all as specified and directed. |
| 63 | S&F in repair for Angle cock, fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed suitable for 15mm bore pipe complete all as specified and directed. |
| 64 | S&F in repair Vitreous China bowl urinal flat back, size of 465x355x265 mm white (minimum), with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe |
| 65 | S&F PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified and directed. |
| 66 | M&L for Flush pipe of polyethylene of high density or PVC 32 mm dia complete all as specified and directed. |
| 67 | S&F in repair looking mirror 600x450x5mm thick with aluminium channel frame, selected quality mounted on 6 mm thick commercial ply wood back and fixed with chromium plated brass screws and cup washers complete all as specified and directed. |
| 68 | S&F in repair Toilet paper holder with flat recessed type stainless steel complete all as specified and directed |
| 69 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed |
| 70 | S&F in repair chromium plated fancy type 15mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 71 | S&F in repairs towel rail 600 mm long 20 mm dia Brass chromium plated fixed to wall D type with CP steel screws etc, complete all as specified and directed |
| 72 | S&F 150 mm size MS pressed handles oval type stove enameled black, complete all as specified and directed. |
| 73 | S&F 200mmMild steel, semi-barrel tower bolt, open cover, with sheet pressed barrel, stove enamelled black with bright bolt and fixed complete all as specified and directed. |
| 74 | S&F 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed. |
| 75 | S&F Stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tack/galvanised wire staple complete all as specified and directed. |
| 76 | S&F in repairs 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 77 | S&F in repairs 110mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 78 | S&F in repairs 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 79 | S&F in repairs 75mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 80 | S&F in repairs 75mm PVC (SWR) floor trap, plain with grating cover including jointing with solvent cement complete all as specified and directed. |
| 81 | S&F in repairs 75mm PVC (SWR) multi floor trap, plain with grating cover including jointing with solvent cement complete all as specified and directed. |
| 82 | Dismantling water tanks of 500 Ltr capacity and removing to store complete all as specified and directed. |
| 83 | M&L 500 ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) incl 20mm PTMT ball valve (Ball valve make:- Prayag) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed. |
| 84 | S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 85 | M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thick, with grey cement and pigment, complete all as specified and directed. |
| 86 | Ditto all as above but no pigment |
| 87 | Supply and laying sand (25 mm thickness) for cushioning to interlocking paver block complete all as specified and directed. |
| 88 | M&L cement concrete type B1-1:2:4 (using 12.5 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge,coping etc complete all as specified and directed. |
| 89 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying UG cable/foundation etc. n exc 10 sq m on plan and getting out in soft/loose soil, complete all as specified and directed. |
| 90 | M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundation of manholes, filling and mass concrete etc complete all as specified and directed |
| 91 | M&L for PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregrate) as in bed to 150mm internal dia RCC/SGSW drain pipes including packing under and haunching against sides of pipes after they are laid and tested complete all as specified and directed. |
| 92 | M&L for rendering 15mm thick in cement mortar (1:3) mixed with water proofing liquid on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 93 | M&L 50mm internal dia for salt glazed stone ware drain pipes, and jointed in cement mortar (1:1) complete complete all as specified and directed |
| 94 | Returning filling in with excavated soil including spreading, leveling, watering & well ramming in layers not exc 25 cm thick complete all as specified and directed. |
| 95 | Removing excavated surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed. |
| 96 | Dismantling and taking down carefully U/S copper/aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed. |
| 97 | Dismantling and taking down carefully sub-main wiring/ service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified and directed. |
| 98 | Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified and directed. |
| 99 | M&L for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS-H) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of GI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) as earth wire connected with main common earth dolly complete all as specified and directed for the following :-One light/fan/bell/exhaust fan point controlled by one, one-way non modular switch 5/6 Amp complete all specified and directed. |
| 100 | One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way non modular switch complete all specified and directed. |
| 101 | One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way non modular switch complete all specified and directed . |
| 102 | All as per item No 99 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated FRLS but unsheathed single core for16 Amps power point on independent board and 2.5 sqmm FRLS cable as earthwire complete all specified and directed. |
| 103 | S&F switch piano flush type white finish 5/6 Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed. |
| 104 | S&F socket out let 2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz complete all as specified and directed. |
| 105 | S&F switch piano flush type white finish 15/16 Amps single pole one way, 230 volts, 50 hz complete all as specified and directed. |
| 106 | S&F socket out let 5 pin 15/16 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz complete all as specified and directed. |
| 107 | S&F fan regulator, stepped type, electronic (socket type),100 watt compatible with BLDC FAN complete all as specified and directed. |
| 108 | S&F lamp holder (Angular/Straight), insulated body, with back plate for batten fitting complete all as specified & directed. |
| 109 | S&F LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 950 suitable for \\"B-22 type to fix on batten holder complete all as specified and directed. |
| 110 | M&L ceiling rose 3 terminal/PVC/polycarbonate, isolated body complete all as specified and directed. |
| 111 | S&F sheet metal enclosures with metal socket and plug top Single pole and neutral enclosure with a two pin and earth plug and socket complete ISI marked, 230/240 volts, 50 hz with one single pole MCB SP 25 Amps complete all as specified and directed. |
| 112 | S&F MCCB/MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with with 200 Amps rated busbar minimum IP 43 degree of protection with built in copper bus bar of suitable size, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface including taking down existing unserviceable MCB DB of any description complete all as specified and directed. Note: MCCB/MCBs shall be measured and paid separately. |
| 113 | S&F sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 8 way with 100 Amps rated busbar, minimum ingress protection of IP 40 complete all as specified and directed. |
| 114 | S&F MCB, SP, AC, 240 volts of 05 to 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.Note: MCBs should be of same make as of DB 8 way |
| 115 | S&F MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.Note: MCBs should be of same make as of VTPN 4 way and DB 8 way |
| 116 | S&F MCCB 100A, 16 KA, 4 Pole, 415 V, 50 Hz, Ics=100% Icu with fixed thermal magnetic release fixed in Vertical TPN complete all as specified and directed..Note: MCCB should be of same make as of VTPN 4 way |
| 117 | S&F in replacement of old unserviceable LED T5 tube light fitting 20 watts with polycarbonate housing and polycarbonate diffuser with integrated electronic driver with all accessories including connecting up with pvc insulated and pvc sheathed twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed. |
| 118 | S&F Decorative ultra slim round profile LED Tube light fitiing with extruded polycarbonate, energy efficient for mirror light 9/10 Watt 2 ft with LED light source with uniform light output, fixed on site with all accessories all as specified & directed. |
| 119 | S&F LED 30 watt Building security light fitting mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for driver,including bracket clamp and fixing accessories complete with electronic driver and all accessories. The fitting shall IP 66 protection, duly prewired complete all as specified and directed. |
| 120 | S&F in replacement of surface/recessed mounted LED panel light 2'x2' size, 36 watts, full white/warm white as per site requirement with electronic driver in CRCA sheet steel body with polycarbonate diffuser suitable for POP/Amstrong/grid false ceiling complete with all fixing accessories including making electrical connection with pvc insulated and pvc sheathed twisted two core wire of suitable size complete all as specified and directed. |
| 121 | S&F in replacement wall light fitting with brushed nickel/ stainless steel base, made out of polycarbonate/glass diffuser suitable for and including 9 Watt WW/CDL LED Bulb fixed on wall and making electrical connection complete all as specified and directed. |
| 122 | S&F sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLS) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion complete all as specified and directed. |
| 123 | Ditto all as above for 4 sqmm size |
| 124 | S&F in repair Ceiling fan complete with three blades down rod, accessories 230 V, 1200mm sweep, BEE 5 star white/ warm white with squirrel cage induction motor complete all as specified and directed.Note: Old Ceiling fan to be deposited in MES store Yard |
| 125 | S&F in repair Exhaust fan Steel body AC single phase 230/240 Volt of size 300 mm sweep, complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed .Note: Old Exhaust fan to be deposited in MES store Yard |
| 126 | S&F in repair Exhaust fan PVC body AC single phase 230/240 Volt of size 250 mm sweep, rpm not less than 1100 rpm complete with louvers shutter including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed .Note: Old Exhaust fan to be deposited in MES store Yard |
| 127 | S&F in replacement electric water heater,storage type steel body with stainless steel inner tank and heating element upto 1.5/ 2 KW capacity 25 litre, BEE 5 Star rated, ISI Marked, 240 V, 50 Hz complete with all accessories such as safety valve, thermostate, NRV, Hot and cold water connection pipe all as specified and directed.Note: Old Water heater to be deposited in MES store Yard |
| 128 | Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron, UL listed, CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 50kg/pit(resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7.The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size:270x240x200mm) and FRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including light grade GI pipe of size 15 mm upto 7 mtr incl cutting and chases on wall and floor and aking good using PCC complete all as specified and directed.Note :- On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost. |
| 129 | Supplying & laying in replacement of LT UG cable (Conforming to IS 1554) ISI marked 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor in trenches/ducts/through HDPE pipe under roads of size 25 sqmm 4 core complete all as specifed and directed. Note;- The earth work shall be measured and paid sepretely under appropriate item of Sch A. |
| 130 | Ditto all as above but 10 sqmm, 4 core |
| 131 | M&L for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/ floors/ duct or fixed on walls/pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed. |
| 132 | S&F GI tubing light grade ISI marked of 50 mm bore dia complete all as specified and directed. |
| 133 | S&F in replacement of old unserviceable Post Top lantern globe type light fitting of capacity 1x7/8 watts with B-22 base LED bulb, transparent polycarbonate diffuser and fixing arrangement on new GI pipe of 25/40 mm dia medium grade of length 1.5m duly grouted on ground/wall/brick pillar with the help of cement mortar including making electrical connection with PVC insulated and PVC sheathed twisted three core wire of size 0.5 sqmm from junction box to light fitting complete all as specified and directed at site. |
| 134 | S&F in replacement PVC/DK Thermoplastic cable junction boxes IP 65 with metric knockouts for cable entry, weather proof suitable for outdoor installation for Gate light and Post top lantern, fixed on wall with screw & rawal plug and on GI Pipe wth suitable size MS clamp and Nut-bolts, washer of size 150x100x60 mm complete including one connector block three terminals and PVC cable gland 02 Nos for incoming and outgoing cables with provn of 01 nos single pole MCBs 10-32 amps inside the box including taking out/down existing unserviceable junction box of any description complete all as specified and directed at site. |
| 135 | S&F in replacement of old unserviceable twin core of flexible wire of size 23/0.0076 with PVC medium grade pipe 20mm dia for connection of post top lantern fitting from one junction box to other junction box complete all as specified and directed at site. |
| 136 | Drilling and tapping GI water mains 50mm bore (in position) for branch connections of the internal dia 20mm, complete all as specified and directed. |
| 137 | S&F straight plain brass ferrules (or connecting screws) screwed both ends and fixed to water mains for tapping branch connection of 20 mm bore pipe, complete all as specified and directed. |
| 138 | Taking down existing unserviceable gate valve & Supply and Fix Gun metal gate valve, ISI marked, with iron wheel head screwed both ends for iron pipe, fixed in repairs complete of size 20 mm bore Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysSep 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender