Tender For Construction Of Pre Fab Structure At New Transport Yard At Skims Soura..
Tender Value
1.02 Crore
Estimated cost
Bid Submission
05 Sep 2026
12 days left
EMD
2.05 Lakhs
Bank guarantee accepted
Document Fee
1800
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Pre Fab Structure At New Transport Yard At Skims Soura..
BOQ
| Sl. No. | Item Description |
| 1 | CIVIL PART |
| 2 | Earth work in bulk excavation by Manual / mechanical means (hydraulic excavator) over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. all kinds of soil |
| 3 | Providing and laying stone soling in the excavated trenches duly hand packed on level including ramming with iron hand rammers including loading, unloading carriage T&P complete |
| 4 | P/L, in position cement concrete of specified grade excluding the cost of centering & shuttering. All work up to plinth level in 1:4:8 (1cement: 4 coarse, sand: 8 graded stone aggregate of 40 mm Nominal size (Crushed) all inclusive leads, lifts, loading, un-loading,cost and carriage of material involved |
| 5 | P/L, in position reinforced cement concrete of specified grade excluding the cost of centering & shuttering. in 1:1.5:3 (1cement: 1.5 coarse sand: 3 graded stone aggregate of 20 mm Nominal size Crushed upto plinth level- level |
| 6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 4.4.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Centering & shuttering including strutting , propping etc. and removal of same: in walls any thickness foundation , footings bases etc |
| 8 | Reinforcement for R.C.C work incld straightening, cutting, bending, placing in position and binding all complete:- (Thermo Mechanically Treated Bars.).sill level & lintel strip, f-beam Room, f-beam V,plinthband |
| 9 | Supply & Filling of GSB / khak bajri Under floor |
| 10 | Filling available Earth under Foundation Sides |
| 11 | 12mm thick cement sand plaster in 1:4 mix (1 cement: 4 coarse sand). all inclusive leads, lifts, loading, un-loading, cost and carriage of all materials from approved nearest sources to site of work complete.incl cost of scaffolding. |
| 12 | Structural steel work in built up sections, trusses and framed work, including cutting,welding, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 13 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.: |
| 14 | a) 25mm nominal bore |
| 15 | b) 20mm nominal bore |
| 16 | c) 15mm nominal bore |
| 17 | Providing and fixing of PVC pipes of approved make C- Class ( Prince, Finolex or equivalent as approved by Engineer-in- Charge ) including rubber gasket etc.following fittings of approved make. 100mm nominal bore |
| 18 | P/F of high rib profile sheet of required colour for roofing 0.5mm thick I/C cost of screw, washers etc complete job (sample to be approoved by engineer in charge) including ridges hips valleys |
| 19 | 50 mm thick cement concrete flooring in (1:2:4) mix laid in glass strip panels and finished with neat cement slurry including all carriages. |
| 20 | Providing anfd fixing of wall panel 60 mm thick (puff panel) and width 1m or more insulated thick panel with 0.5mm PPGI sheet both sides with density of 40kg/m3 fixing on steel frame work with necessary flashings,C channels and corners, fastners, EPDM washers, silicon sealants, screws incl providing of araldite and all carriages of material upto site complete job |
| 21 | Providing and Fixing ofAluminium Hardware Fittings of Standard Quality |
| 22 | Handels 200 mm |
| 23 | tower Bolt 250 mm |
| 24 | air Hook |
| 25 | L Drop |
| 26 | Providing anfd fixing of wall panel 40 mm thick (puff panel) and width 1m or more insulated thick panel with 0.5mm PPGI sheet both sides with density of 40kg/m3 fixing on steel frame work with necessary flashings,C channels and corners, fastners, EPDM washers, silicon sealants, screws and providing araldite and all carriages of material upto site complete job |
| 27 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separatelyAnodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic |
| 28 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm) |
| 29 | Poviding and fixing of 1 mm thick MS sheet for soffits over angle iron frame work 25 x 25 x 4 mm all complete including cost of scaffolding. (soffit)10.2.2 and incl priming coat complete job |
| 30 | Poviding and fixing of 1 mm thick MS sheet for Eves Boarding over angle iron frame work 25 x 25 x 4 mm all complete including cost of scaffolding incl priming coat |
| 31 | Providing and laying autoclaved aerated cement blocks masonry with150mm/230mm/300 mm thick AAC blocks in super structure above plinth level +B161:G162up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for separately).6.52 |
| 32 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete as per directions of engineer in charge (600x600 mm) |
| 33 | Providing and fixing Ist quality ceramic glazed wall tiles of approved make, in all colours, shades(of 7-8 mm thick of different sizes) as approved by Engineer- in-Charge, inwalls, skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) |
| 34 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 MM SAND cast iron P or S Trap,10 liter low levelwhite P.V.C Flushing Cistern,including flush pipe,with manually controlled device(handle Lever),with all fittings and fixtures complete,including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 18.1.3 |
| 35 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 36 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 37 | Providing and fixing toilet paper holder with Flap made out of C.P BrassMakes:-Jaquar/Hindware/Cera |
| 38 | Providing and fixing C.P Brass Soap Dish.Makes:- Jaquar/Hindware/Cera |
| 39 | Providing and fixing health faucet with hose pipe for european water closet complete in all respect of approved quality\Makes:-Jaquar/Hindware/Cera with CP channels |
| 40 | Providing and fixing health faucet with hose pipe for european water closet complete in all respect of approved quality\Makes:-Jaquar/Hindware/Cera with CP channels |
| 41 | Providing and fixing C.P bib cock of approved quality short body Makes:-Hindware/Jaquar/Cera (15 mm nominal bore) |
| 42 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (15 mm nominal bore) |
| 43 | P/F of 100 mm dia PVC Plain Bend |
| 44 | P/F of PVC Collar complete 100 mm |
| 45 | P/F of 100 mm dia PVC floor trap of approved quality |
| 46 | P/F of CP angle valve of approved quality 15 mm dia |
| 47 | P/F of aluminum composite pannel of approved make(complete job) (3mm) |
| 48 | P/f 15cm wide 45 cm overall semi circular plain GS sheet gutter with iron brackets 40*3 mm size bolts, nuts and washers extra including making necessary connections with rain water pipes complete.0.63 mm take with zinc coating, not less than 275 gum/ sqm |
| 49 | P/F of PVC pipes/ fittings of approved make and quality 9prince or finolex) ISI quality of dia 50mm dia |
| 50 | P/F of plain bend 50mm |
| 51 | P/F of collar 50mm |
| 52 | P/F of elbow 50mm |
| 53 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design : 45x45cm &45cms deep incl CI cover with frame (total wt. of frame /cover to be nor less than 38kg) |
| 54 | Brick work with common burnt bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in 1:4 mix cement mortor all carriages complete. |
| 55 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 56 | CARRIAGE OF MATERIALS |
| 57 | AAC Blocks carriage=6.43cum ,@97bricks/cum=624AAC Blocks |
| 58 | Sand for an av lead of 20 Km |
| 59 | Stone aggregate below 40mm size for av lead of 20Km |
| 60 | bricks 30 kms lead |
| 61 | ELECTRIC PART |
| 62 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 63 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surfacel recessed medium class PVC conduit as required. |
| 64 | 2 x 2.5 sq. mm +1 x 2.5 sq. mm earth wire |
| 65 | 2 x4 sq. mm + 1 x4 sq. mm earth wire |
| 66 | 2 x 6 sq. mm + 1 x 6 sq. mm earth wire |
| 67 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 68 | 5/6 A switch |
| 69 | 3 pin 5/6 A socket outlet |
| 70 | 15/16A ,6pin socket Switch (forHeating Point) |
| 71 | 15/16A ,5pin socket outlet (forHeating Point) |
| 72 | Bell push |
| 73 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 74 | Supplying and fixing following size modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 75 | 4 Module (125mmX75mm) |
| 76 | 6 Module (200mmX75mm) |
| 77 | 8 Module (125mmX125mm) |
| 78 | Supplying and fixing following size modules, PVC box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 79 | 4 Module |
| 80 | 6 Module |
| 81 | 8 Module |
| 82 | Supply & fixing of following sizes of PVC conduit along with accessories in surface / recessed including cutting the wall & making good the same in case of recessed conduit as required, (for conduiting in working stations From junction box in raceway.) 25/32 mm |
| 83 | Supplying and Fixing 25 mm Double Locked PVC Channel 2 mm thick |
| 84 | 4 feet long LED batten 6000/6500k Light with anti-glare diffuser with energy efficient electronic driver CRI greater than 80 with minimum sytem lumens 4000 and maximum wattage24 including connection with multistrand copper conductor 3 core cable etc as required at site with burning hours >= 50000 Hours having system lumens 110 Lm/watt. |
| 85 | 80W Indoor & Hanging Type Round LED luminaire • Operating temperature:-10° C to +45° C • Operating voltage range: 140 -270 V • Average life Min. : 50000 Burning hours • Housing Aluminum alloy pressure die casted housing & control gear box Finish• The fixture is epoxy powder coated withcolour munshell grey finish. • Light source High efficiency long life LEDs with lumen efficacy of >150 lm/W with view angle• 120º to ensure better uniformity of light distribution. • Electronic driver Buit In, electronic driver with APFC, lower THD, Open Circuit Protection, Surge Voltage Protection upto 10 kV with Built In SPD &• other safety test as per IS 15885 Part-2/Sec 13.• 80W Wide Beam,• Nominal Vol. 240V• Current 0.350A• Power Factor Greater than 0.95• Color Temp. 5700K• IP65 |
| 86 | Supply installation testing and commissioning of following sizes of metallic type exhaust fans with Bird guard to protect fan in running condition, Double ball bearing with Heavy duty motor. |
| 87 | i) 9\\" |
| 88 | ii) 18\\" |
| 89 | Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factornot less than 0.9, Service Value (CM/M/\N) minimum 6.00,Air deliveryminimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speedcontrol and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (ma><.), insulation resistancemore than 2 mega ohm, suitable for 230 V, 50 Hz, single phase ACSupply, earthing etc. complete as required, including Fan Dimmer 150W |
| 90 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, Ceiling fan, Induction Type, Class of insulation: B, 3 Nos. Blades, 30 cm long down rod, 2 Nos. Canopies, Shackle kit, Safety rope, Copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 230 CMM, > 270 RPM (tolerance as per IS : 374-2019), THD less than 10% and all remaining accessories including safety pin, Nuts / Bolts, Washers, Temperature rise = 75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, Single Phase AC Supply, Earthing etc. complete as required. The Job includes providing, fixing and commissioning of the associated Fan Regulator. The Ceiling fans are to be provided with a 3 years' Warranty on Motor and 2 years' Warranty on other parts. |
| 91 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker IK09 and IP43 suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 92 | Single pole 5-32 A |
| 93 | Double pole 40A |
| 94 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) |
| 95 | 16 way, Double door |
| 96 | Supplying and fixing following rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB complete with connections, testing and commissioning etc. as required. |
| 97 | a) 40A TPN |
| 98 | b) 63A TPN |
| 99 | SITC of Electric Heater / Geyser of capacities as mentioned below with following parameters .1.Energy saving. 5 Star Certification by BEE 2. Provision of Temperature regulation by means of external Knob3. Power Rating:- 220/ 230V, 50 Hz, Single Phase. 4. Maximum Rated Pressure.= 8 bar 5. Installation Type Vertical / Horizontal mounted as per site requirement 6. Body Type:- Rust, water proof and Shock Proof outer body with attractive looks and corrosion resistant inner tank made of cold rolled steel ,resistant to hard water. 7. Element Type:- glass coated heating element to prevent from corrosion and hard water.8.Safety Valve maximum pressure =8 bar maximum9. Energy efficiency feature:- Should have high density PUF insulation for energy Saving10. Anti syphon system to prevent back flow of water. 11. Should have Indicating Lamps for ON & CUTT OFF.12. Conforming to :IS 2082:2018 , IS 302-1, IS 302-2-21 |
| 100 | 50 litre (2KW) |
| 101 | Providing and laying of spans of 3 ½ core/2 core XLPE Al. cable Armored of various sizes as mentioned below in place of damaged/burnt out / fresh ones of 1.1KV as per IS 7098/ II/ 85 with latest amendements |
| 102 | 10 mm sq 2-core |
| 103 | 25 mm sq. 3 ½ core |
| 104 | 50 mm sq. 3 ½ core |
| 105 | 120 mm sq. 3 ½ core |
| 106 | Supplying and making end termination with Aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. |
| 107 | 16 sq. mm |
| 108 | 25 sq. mm |
| 109 | 50 sq. mm |
| 110 | 120 sq. mm |
| 111 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 150 A, 16 КА, ТРМССВ, with Outdoor type enclosure of 2mm thick CRCA Powder coated M.S Sheet. Complete Job, including Masonary work, as required. |
| 112 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part ll complete with fitting and cutting, jointing etc. in the existing trench, complete as required. |
| 113 | 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 114 | 200 mm dia (OD-200 mm & ID-175 mm nominal) |
| 115 | Supply, Installation, Testing & Commissioning, cubicle type compartmentalised board made out of 2mm thick CRCA sheet, totally enclosed, IP 62, floor mounted with channel base frame, dust and vermin proof, Out-door, suitable for operation on 415V, 50 Hz AC with control wiring with 2.5 sqmm size wires/cable, interconnection, including supply & installation of following switchgears, metering instruments, Bus Bars (min. 1.5 times the max. current), Indicator, Meters and accessories as per specifications, Complete job:Incomer MCCB 150 A, 35 КА, ТРМССВ,Adjustable Thermal & Adjustable Magnetic, Rated Ultimate Shortcircuit Breaking Capacity Icu at 415 V (kA rms): 50, 4Pole, icu= ics = icw=75%, 1no.Outgoing MCCB 100 A. 16 KA.ТРМССВ 4no.Outgoing FP MCB ‘C’ Curve 63A 4 no.Outgoing DP MCB ‘C’ Curve 25A 4 no. |
| 116 | Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoall coke and salt as required. |
| 117 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 118 | Supply and fixing of 8.0 mtr Long GI (65 micron DFT single dip) Octogonal poles uniformally tappered with thickness of 3mm with bottom/top Dia of 155 mm x 70mm & base plate of 260 x 260 x 16mm / pcd 250 mm provided with proper door opened gear box for connections on the bottom side with G.I. Foundation Bolts (J Type) M20x700 mm long (Set of 4 no.’s per pole) |
| 119 | Laying of RCC foundation for 8.0 mtr. Long Octagonal poles including proper curing. 0.585mX0.585mX1.0m (RCC with concrete ratio 1:1.5:3 with minimum 8 Nos. of 12 mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200 mm C.C for fixing the pole). |
| 120 | Supply and fixing of Earthing of Octagonal Pole Complete by GI Pipe 40 mm or GI Rod 20mm 3 mtr long through GI Strip (25x3)mm |
| 121 | Supply and fixing of Pre-fabricated galvanized double way top bracket (1500mm long with 48.3 OD GI Pipe) to be fitted on top of Octogonal pole for holding lighting |
| 122 | Supply and fixing of DK thermoplastic cable Junction/ Termination T boxes 8\\"x10\\"of class IP55/IP65 fitted with two 2-5 Amp MCB strip, 4-way terminal block / connectors including copper lugs, Clamps, Nuts & Bolts, Washers etc. or poles with two-way type bracket to be fitted properly inside the door opened gear box provided on the bottom side of the pole. |
| 123 | Supplying, Installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 Hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66/67 protection, IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & Electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). 120 - 150 Watt LED Luminaries |
| 124 | Supply and fixing of Surge Protector for the 120/190 watt LED type lighting fixture complete |
| 125 | Design, Fabrication, supply, installation testing & commissioning of Outdoor Type Electrical Panel of cubical construction, having 4 Nos. Angle-iron legs of suitable dimensions, to be sufficiently grouted (> 750mm depth), in 1:2:4 concrete mix, onto outdoor land / concrete as per site requirement, fabricated out of 2 mm thick sheet Steel, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated, cable alley, inter-connection with suitable size solid Aluminium strip, earth terminals and earthing, complete in all respects with following Incoming / Outgoings, suitable for operation on 415V, 3 phase, 50Hz, AC Supply with enclosure protection Class IP42 as required alongwith Digital Voltmeters / Ammeters / CT Coils of requisite Ratio / Selector Switches / LED Indications / with requisite glands as per the instructions of the Site Engineer: Incoming:(i) 100A, 50kA, 4-Pole MCCB : 1 Nos (ii) 200A, TPN, Aluminium Busbar : 1 SetOutgoing: (i) 63A, TPN, MCB : 2 Nos. (ii) 40A, DP, MCB : 10 Nos.The Panel is to be fitted with astronomical/Photovoltic switching with contactor(s) of required capacity. |
| 126 | Dust/rain/snow-proof canopy type mini-outdoor LT feeder panel of size 450 × 300mm with front door opening duly powdered colour coated with inbuilt 2Nos TPN 16-32 Amp MCCB,TPN busbars of same capacity installed on cement concrete block with 4 angle iron legs grouted in the cement concrete of termination of main 25sqmm cable and outgoing 25/16 sqmm cable circuits. |
| 127 | Supply, Installation, Testing and Commissioning of continuously tapered multifaceted and polygonal cross section High mast of height 12.5 Metres as per detailed specification & details given:-a) Dimensions:Top Dia-150mm, Bottom Dia-360mm, 2 sections (section Length-6500mm) making a final overlap of 1000mm, thickness- 3mm, Base Plate :- dia 520 mm x 25 mm, PCD 445mm having suitable sectional length with slip joints between sections without any circumpherencial welding.b) Double drum winch with separate handle for manual operation of winch with a torque limiting device for safe docking of carriage.c) Raising/lowering type lantern carriage designed to carry 6 Nos luminaries, 3 suspension head frame, L-Stopper (3 Nos), mounting plates, trailing cable; control gear box, junction box and top pulley assemble with weather proof cover.d) Necessary suitable length for lowering & rising of lantern carriage of stainless steel wire ropes of 7/19 construction (with minimum 6mm dia) and multicore flexible copper power cablee) Hinged service door in base section base plate earthing terminal.f) Suitable arrangement for supply distribution with termination of suitable size underground cable in high mast.g) Complete with other provision(s) for execution in the confirmation with detailed technical specifications.h) Lightning conductor finial made of 25mm dia 300 mm long G.I. tube having single prong.i) Integral single power tool (electrical) for lowering & raising of high mast with separate manually operated system.j) Anchor plate, templates, foundation bolts (M24 x 750mm x 6 Nos) manufactured from special steel along with nuts, washers etc. |
| 128 | Design & casting of RCC Foundation of 1500mm(H)X 750mm x 750 mm size with M-20 (1 Cement, 2 coarse, 4 Stone aggregate) complete with 10/12mm dia. M.S. bar for reinforcement( 50kg/cum) along with centering & shuttering i/c fixing 750mm long, 25 mm dia J type G.I, coated foundation bolt/ Anchor bolt with template suitable for 12.5 mtr polygonal pole complete with excavation the soil & refilling, ramming, curing etc. as reqd. |
| 129 | Providing and Installation of LED FLOOD light fixture IP65/66 powder coated with following specification1. Input voltage : 150 V to 270 V 2.Lumens : Min 200003. Power factor : >0.904. Life expecting : more than 50,000 hours5. No of hours usage / day : 10 to 12 hours/day6. Rated watt : 200-220 W7. Colour Temperature : 5,500 to 6,500 K with test certificate8. Ingress protection : IP 65/IP 66 as per IS/IEC60529-2001 with test certificate9. Total harmonic distortion (THD): <10%10. Working Temperature : 0 deg to 50 deg11. Luminary Casing : Pressure die cast Aluminum with toughened glass cover and water proof fixture |
| 130 | Supply and laying of following sizes of PVC insulated, overall PVC sheathed, FRLS, 1.1 kV grade, unarmoured, Copper wire, 1.5 sq. mm, 3-Core |
| 131 | Providing and laying in position cement concrete of specified grade excluding cost of centering and shuttering (All works up to plinth level) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender