Tender For Provn Of 02X Combine Toilet Bathroom For Jcos Block, Bldg No Lp/294 And For Unit Location At Sikh Li , Mtn Arty Bde Camp And At Bomdila And 01 X Guard Room With Toilet At Rwa Upper Dahung Of Age B/R And Age E/M Under Ge Tenga
Tender Value
38.30 Lakhs
Estimated cost
Bid Submission
11 Sep 2026
19 days left
EMD
76600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kameng → Arunachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of 02X Combine Toilet Bathroom For Jcos Block, Bldg No Lp/294 And For Unit Location At Sikh Li , Mtn Arty Bde Camp And At Bomdila And 01 X Guard Room With Toilet At Rwa Upper Dahung Of Age B/R And Age E/M Under Ge Tenga
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard /dense soil |
| 2 | Excavation in trenches n,exc 1.5 m wide and n.exc 1.5 m deep for foundation and getting out in hard/dense soil. |
| 3 | All as per serial item No 2 above but exceeding 1.5meter but not exceeding 3.00 mtr in depth complete all as specified and directed.. |
| 4 | Excavation in trenches in any type of soil not exc 1.5 mtrs wide and not exc 1.5 mtr in depth for laying of pipe/ cables/ poles/fencing posts etc and getting out complete all as specified and as directed. |
| 5 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard/dense soil. |
| 6 | Excavation over areas n exc 1.5 m deep and getting out in hard/dense soil. |
| 7 | Returning/filling in including spreading, levelling, watering and well remming in hard/dense soil. |
| 8 | Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point. |
| 9 | M&L PCC 1:4:8 type D2(using 40mm graded aggregate)as in foundation filling and mass concrete etc. |
| 10 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete. |
| 11 | M&L for MS TMT bars 10mm dia and over, cut to lenth, bend to shape required, including cranking, bending, sprially for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. |
| 12 | M&L for MS TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to lenth, bend to shape required, including cranking, bending, sprially for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. |
| 13 | Use & waste Form work to soffits of suspended slabs such as roof slab. Floor slab, landings and similar work n.exc 200 mm thick for rough finish flat surface of concrete. |
| 14 | Use & waste Form work to edges of concrete flat, tread, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5 cm but n.exc 10 cm wide for rough finish surfaces of concrete. |
| 15 | M&L for Reinforcement cement concrete type B1 1:2:4 in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like |
| 16 | M&L rendering 15 mm thick in CM 1:4 over brick or concrete surfaces finished even and smooth without using extra cement . |
| 17 | M&L for newly plastered surfaces of walls and applying two coats of cement based paint, over a coat of primer complete all as specified and directed. |
| 18 | M&L for rendering 15 mm in CM (1:6) over brick or concrete wall surfaces finished even and smooth without using extra cement. |
| 19 | M&L Preparing newly plastered surfaces of walls and applying two coats of white wash. |
| 20 | M&L hard core of gauge n.exc 63mm, deposited, spread and levelled in layers nexc 15 cm thick, watered and rammed to a true surface. |
| 21 | M&L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as cement concrete in Sub-base floors, sub-bases floors and pavings etc complete all as specified. |
| 22 | M&L for 25 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) in sub base of floorings. |
| 23 | M&L for 15 mm thick screed bed in CM 1:4 for laying floor tiles . |
| 24 | M&L for 20 mm thick screed bed in CM 1:4 for laying floor tiles . |
| 25 | M & L for Non-skid ceramic tiles 7 to 8 mm thick coloured tiles( square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match. |
| 26 | M & L for Chequered cement concrete tiles 20cm x 20cm x 25mm/ 30cm x 30cm x 25mm thick,set, jointed and pointed in neat cement slurry in floors. set and jointed in grey cement and no pigments to match. |
| 27 | M & L for 10mm thick rendering in CM 1:3 on fair faces of brick work or concrete surfaces finshed rough to receive tiles . |
| 28 | M & L for 350 x 250 x 7 mm/450 x 350 x 7 mm thick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. |
| 29 | M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, (40mm graded stone aggregate) as in plinth protection, finishing the top surfaces even and smooth W/O using extra cement. |
| 30 | S & F 3mm thick figured glass, pin head glazing with oil putty /wooden beads in squares n exc 0.50 Sqm in each pane. |
| 31 | S&F Pre-Painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour havimg testile strenght of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified and directed. |
| 32 | S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying and fixing in opening as per specification and drawing. |
| 33 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing. |
| 34 | S&F 100mm size stainless steel butt hinges, medium weight, cold rolled complete with stainless steel screw etc. all as specified as directed. |
| 35 | S&F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin type B-21, anodised and fixed.complete all specified and directed |
| 36 | S& F Aluminium anodised barrel tower bolts 150mm long of extruded section and fixed |
| 37 | S & F 150mm size extruded aluminium alloy handles, fabricated type anodised |
| 38 | S&F vitreous china wash down water closet pan of pedestal pattern, white with 'P' or 'S' traps, including connecting to trap, seat cover and to flushing pipe etc complete all as specified. |
| 39 | S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed by Engr-in-Charge |
| 40 | S & F 10 litres PVC, Syphonic action type, Flushing cistern low level, white with inlet ball valve float chain and pull and brackets complete. |
| 41 | S&F PVC connection of 15 mm size with PTMT nuts of length 450 mm |
| 42 | S&F PVC connection of 15 mm size with PTMT nuts of length 600 mm |
| 43 | S&F PVC (SWR) pipes single socketed 110mm dia in any length with rubber ring joints fixed to walls |
| 44 | S&F PVC (SWR) pipes 110mm dia single sockted in any length with rubber ring joints laid in trenches or floors. complete all specified and directed |
| 45 | S&F PVC (SWR) junction single, (single T) equal or unequal with access door 110mm dia. |
| 46 | S&F PVC (SWR) bends any radius, bend 110mm dia. |
| 47 | S&F PVC (SWR) bends any radius with access door, 110mm dia.complete all specified and directed |
| 48 | S&F PVC (SWR) vent cowl 110mm dia |
| 49 | S&F PVC (SWR) vent cowl 75mm dia |
| 50 | S&F PVC (SWR) WC connector 110mm dia lip ring. |
| 51 | S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement. |
| 52 | S&F PVC (SWR) pipes 75mm dia single sockted in any length with rubber ring joints fixed to walls. |
| 53 | S&F PVC (SWR) pipes 75mm dia single sockted in any length with rubber ring joints laid in trenches or floors.complete all specified and directed |
| 54 | S&F PVC (SWR) bends any radius with access door, 75mm dia. |
| 55 | S&F in 15mm bore steel water tubes, medium grade, galvanised with all fittings and fixed complete to walls/ceilings or laid in trenches complete all specified and directed |
| 56 | S&F 15 mm dia bib taps, fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed. |
| 57 | Supply and fix chromium plated brass Bib taps,cast copper alloywith crutch or butterfly handle, screwed down for iron pipe for 15mm bore GI tubing complete all as specified and directed by Eng-in-charge. |
| 58 | S&F 15mm bore angle stop valves, fancy type chromium plated, screwed down, high pressure screwed both ends for iron pipe or for unions & fixed. |
| 59 | S&F brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between fllanges. |
| 60 | S&F 600mm x450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board fixed t wooden plugs with chromium plated brass screws and cup washers all as specified and directed |
| 61 | S&F vitreous china wash hand basin white flat back of size 550mmx400 mm including cutting for and pinning in ends of brackets or errecting stand but exclusive of fixing of waste pipe and CI brackets complete all as specified and directed. |
| 62 | S&F 32 mm bore Low density poly ethylene pipes of pressure rating 6kgf/cm2 fixed complete to walls,ceiling or in floors etc. |
| 63 | S&F 15 mm bore chromium plated fancy type pillar tap cast copper alloy with capstan heads, screwed down high pressure,with or without leterred \\"Hot ot Cold\\" with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed. |
| 64 | S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. |
| 65 | M&L for preparation of new wooden surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. |
| 66 | S&F 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc ; sizes of members of shutters as specified in SSR Part-I, section-8, clause 8.24(a). |
| 67 | S & F 30mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for window, ventilators etc are provided with stiles and rails as specified in SSR Part-1, section 8 clause 8.24(b).complete all specified and directed |
| 68 | S & F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. conforming to e 410-W (GdeE- 250) qualityA complete as specified. |
| 69 | S&F Rotational mounded polythene water storage tank of 1000 ltrs capacity, (multilayered, cylindrical, vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I. |
| 70 | S&F Rotational mounded polythene water storage tank of 500 ltrs capacity, (multilayered, cylindrical, vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I. |
| 71 | S&F ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipes of 20 mm dia or brass ferrule and fixed, all as directed. |
| 72 | S&F Gun metal globe or gate valve with Iron wheel head, screwed both ends for 20 mm dia of pipe and fixed. |
| 73 | S&F in 20mm bore steel water tubes, medium grade, galvanised with all fittings and fixed complete to walls/ceilings or laid in trenches complete all specified and directed |
| 74 | S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms). |
| 75 | M&L for construction of 1.20 m dia x 3.00 m deep soakage well, excavation in hard/dense soil foundation PCC 1:3:6 ,wells of honey combed solid block masonry wall, including intercepting chamber, screen chamber, RCC cover slab, filling with brick bats etc complete all as specified in drawing and respective PS. |
| 76 | M&L for cement concrete type D-2, 1:4:8 in Cement concrete in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) |
| 77 | M&L rendering 10mm thick in CM 1:6 on concrete inner surfaces finished even and smooth without using extra cement, complete all specified and directed |
| 78 | M&L for preparation of newly undecorated plastered surfaces of wall and applying 3 coats of white wash, complete all specified and directed. |
| 79 | M&L for PCC 100mm thick, type B-2, 1:2:4 (using 40mm graded sone agg) in sub-floors, sub-base, floors and pavings etc.complete all specified and directed |
| 80 | M & L for screed bed or bedding layer of 15 mm thick for laying floor finishes in CM (1:6 ) complete all specified and directed |
| 81 | S&F 32mm dia waste coupling of PTMT (half or full threaded). (Minimum weight 32mm- 45gms/40mm-60 gms). |
| 82 | M&L cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) to bed of drain pipes including packing under and haunching against the sides of pipes, after they are laid and tested for 110 mm bore pipe complete all as specified and directed |
| 83 | S&F Grating doom 100 mm dia with with waste hole of PTMT (mminium weight 25 gms) |
| 84 | M&L 2nd class hard wood in scantling clean swan timber fixed with frame work as directed. |
| 85 | M&L for Re-inforced cement concrete 1:2:4 type B-1 (20mm graded aggregate) as in Beams, cantilver, Lintel over 1.5m span complete. |
| 86 | Use & waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. |
| 87 | S&F of Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. coFe-410-W(Gde E-250) quality B |
| 88 | M & L for PCC (1:2:4) type B-2 (40 mm graded stone aggregate) Cement concrete in surface channels and drains with WPC 3% by weight of cement complete all specified and directed |
| 89 | Supply only Integrated water proofing compound |
| 90 | M&L precast solid block masonry of block 1:2:4 type B-1 (20 mm graded stone aggregate) wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed. |
| 91 | M&L Rendering 20mm thick on fair faces of brick work or concrete surface in cement plaster 1:4, with WPC 3% by weight of cement finished even and smooth without using extra cement completed all as specified and directed. |
| 92 | Use & waste flat Formwork to faces of Baffle walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all specified and directed |
| 93 | M&L for Precast cement concrete type B1 (20 mm graded stone aggregate) 1:2:4 in cover slabs (for man holes etc.) with plain faces complete all specified and directed |
| 94 | M&L for Reinforcement cement concrete type B1 (20 mm graded stone aggregate) 1:2:4 in Walls, retaining walls, basementwalls, ballast walls and the like;any thickness; above top of footings; including attachedpilaster and buttresses |
| 95 | M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips. |
| 96 | M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 |
| 97 | S&F Mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for Iron steps Fe-410-W (Gde.E-250) quality-A orFe 290 (Gde -E-165)complete all specified and directed. |
| 98 | M&L for Loose filling with broken bricks of gauge 80 to 150 mm in soakage pits, soakage wells |
| 99 | Material & Labour for Light/fan point wiring with 1.5 sq mm (nominal area), PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches ( Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (FRLSH)single core multi-stranded copper conductor cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed. |
| 100 | All as per item No. 99 here in before One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5sq. mm size |
| 101 | All as per item No. 99 here in before but for one 3 pin socket outlet 5 Amps three pin controlled by one switch on independent board complete all as specified directed. |
| 102 | All as per item No. 99 here in before but for one 5 pin socket outlet 15 Amp and 5 Amp Multipurpose independent using 2.5 Sqmm copper conductor cable (multi-strand) PVC insulated and unsheathed cable and 2.5 sqmm copper (multistrand) PVC insulated and unsheathed earth wire with terminal box of size 175mm x 100mm x 3.15mm complete all as specified. |
| 103 | S&F Switch socket combination 2 in 1, 3 pin, 6 Amp flush type |
| 104 | S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type |
| 105 | Supply & fixing switch piano flush type (ISI marked), single pole, one way 15 Amp, 240 Volts complete all as specified & directed. |
| 106 | Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed. |
| 107 | Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed. |
| 108 | S&F LED bulkhead fitting 10 watt (Endura Ruby) with all accessories and including connenting up with twin core twisted with flexible copper conductor cable with suitable size of 230 volts , 50 hz complete all as spicified and directed. |
| 109 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. |
| 110 | Supply and fixing LED light fitting 1 x 20 Watt 220 volt AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as directed. |
| 111 | Supply and fix LED light fitting 1 x10W bulkhead luminaires inculding LED light driver holder connecting up with three core flexible copper conductor cable of suitable size |
| 112 | Supply and fix sheet metal enclosures for DBs Double Door when MCBs to be used 230 volts 04 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board. |
| 113 | Supply and fix sheet metal enclosures for DBs Double Door when MCBs to be used 230 volts 08 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board. |
| 114 | Supply and fix sheet metal enclosures for DBs Double Door when MCBs to be used 230 volts 12 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board. |
| 115 | S&F MCB SPN having braking capacity 10KA, 40-63 Amps, 240 V complete all as specified and directed. |
| 116 | S&F MCB SPN having braking capacity 10KA, 32 Amps, 240 V complete all as specified and directed. |
| 117 | S&F MCB SP having braking capacity 10KA, 6 to 32 Amps, 240 V complete all as specified and directed. |
| 118 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm |
| 119 | Supply and fix exhaust fan,steel body AC single phase, 230V of size 250mm sweep heavy duty with blades, and frame and louvers complete all as specifed and directed. |
| 120 | S&F of new generation energy saving and environmental friendly long life LED building security light made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 power consumption 35 watt complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from ceiling rose to light length as required at site,GI bracket 32 mm dia pipe and 02 numbersclmaps, all fixing arrangements such as fastners, bilts, nuts washers etc all as specified and directed. |
| 121 | Supply and fix electric water heater(Geyser), storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 star rated adjustable temprature setting 0-90 degree C complete with accessories such as safety wall, thermostate, NRV indication lamps, inlet outlet connections,air vent connections, connection pieces including all fixing arrangements such as fastners, bilts, nuts washers etc including making good disturbed wall surfaces matching with the existing surface and finishing complete all as specified and directed by Engr in charge |
| 122 | Supply and fix electric water heater(Geyser), storage type steel body with copper inner tank and heating element up to 2 KW capacity 50 litre, BEE 5 star rated adjustable temprature setting 0-90 degree C complete with accessories such as safety wall, thermostate, NRV indication lamps, inlet outlet connections,air vent connections, connection pieces including all fixing arrangements such as fastners, bilts, nuts washers etc including making good disturbed wall surfaces matching with the existing surface and finishing complete all as specified and directed by Engr in charge. |
| 123 | S&F Stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of size 15 mm. |
| 124 | S&F Bib tap cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified & as directed by engr-in-charge. |
| 125 | M & L for laying of fine, clean sand (river sand) free from sharp materials and stone particals in trenches for cushioning of cable 8 cm thick under cable and 15 cm thick over the cable including gently punning complete all as specified and directed. Note:- The total thickness of sand shall be measured 18 cm after punning. |
| 126 | Supplying and laying un-reinforced precast concerete cable cover, class LV, type 1 flat size 250mm x150mm x 40mm for cable protection , laid flat ie length of cable cover shall be laid across the cable all as specified and directed |
| 127 | Supply, laying & testing in repalcement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 10 sqmm 2 core . |
| 128 | Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric cables with stranded aluminium conductor, 1100 volts grade, of 16 Sqmm 2 core inclduing protection pipe where required complete all as specified and directed. |
| 129 | Supply and laying galvanised tube light grade ISI marked of size 40 mm dia incl all fittings in trenches/fixed on pole/wall/floor or laid in position complete all as specified and directed. |
| 130 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer-in-Charge. |
| 131 | Supply and fixing, metal clad socket out let with MCB single pole 20 Amp, 240 V including sheet metal enclosure complete fixed on flat iron 32x6 mm or 2nd class hard wood wooden board including complete electrical connection by proper size of copper lugs complete all as specified. |
| 132 | S&F wire for circuit/sub main wiring with 1100 volts grade double core PVC insulated and unsheathed cable with multistranded FRLSH copper conductor 4 Sqmm, on surface or recessed or drawn in PVC casing capping/PVC Pipe along with 4 Sqmm single core copper conductor multi stranded (FRLSH ) cable as earth continuity conductor complete all as specified and as directed.(Note: One RM PVC casing capping/PVC conduit ,one run of 4 sqmm earth wire and 2 Run of 4 sqmm cable shall be measured as one run.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysSep 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender