Tender For special Repair To Bldg No S-27 (Or Cook House) And Certain Revenue Work At Masimpur Mil Stn
Tender Value
43.30 Lakhs
Estimated cost
Bid Submission
12 Sep 2026
15 days left
EMD
86600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Cachar → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No S-27 (Or Cook House) And Certain Revenue Work At Masimpur Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of Concrete of any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 4 | Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 5 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 6 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. |
| 7 | Dismantling stone slabs of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar and disposing off complete all as specified and as directed |
| 8 | Demolition of reed lathing, single or double including battens and plaster or chiken wire lathing all as specified. |
| 9 | Dismantling mild steel work or wrought iron of any description and in any position complete all as specified and as directed. |
| 10 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 11 | Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work complete all as specified and directed. |
| 12 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 13 | Dismantling boarding any description fixed in any position with nails all as specified. |
| 14 | Dismantling SGW/asbestos cement/PVC pipe 50/75/100 mm dia including clamps complete all as specified and directed. |
| 15 | Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and as directed. |
| 16 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 17 | Taking down Chowkhats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 18 | Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 19 | Surface dressing n exc 15 cm deep and getting out in soft / lose soil complete all as specified |
| 20 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 21 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 22 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 23 | M&L for earth filling under floor incl spreading ,levelling & well ramming includuing watering as required n exc . 25 cm thick . (Note :- Earth obtained from respective execavation item is reused ) |
| 24 | M&L for Hardcore broken stone of gauge exc 40mm and n exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and directed. |
| 25 | M&L for PCC (1:4:8), Type D2 using 40 mm graded stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 26 | M&L for providing 75 mm thick cement concrete (1:4:8) type D-2 using (40mm graded stone aggregate) as in Sub base of floor rough surface for receiving tile complete all as specified. |
| 27 | M&L for providing 100 mm thick cement concrete (1:4:8) type D-2 using (40mm graded stone aggregate) as in Sub base of floor rough surface complete all as specified. |
| 28 | M & L for Plain Cement Concrete (1:3:6) type C1 using 20mm graded stone aggregate as in surface channel and drain all as specified and directed. |
| 29 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends for etc complete all as specified and directed. |
| 30 | M & L for 75mm thick cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection finished even and fair without using extra cement laid in panels and joints filled with bituminous mastic filling with 1 part of bitumen and 3 part of sand complete all as specified and directed. |
| 31 | M & L for plain cement concrete (1:2:4) type B1 using 20mm graded aggreagate as in bed blocks, coping , cills, steps, kneelers, bed plates, apex stones kerbs and similar works including necessary formwork complete all as specified and directed. |
| 32 | Material and labour for 50 mm thick Plain Cement concrete type B2 1:2:4 (40mm graded crushed stone aggregates) for sub base in floor fair and rough for receiving tiles, topping layer all as specified and directed. |
| 33 | M & L for forming contraction ( Dummy) joints 65mm deep X 10mm wide, filled with sealing compound of 'grade A' complete all as specified and directed by Engr-in-charge. |
| 34 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 35 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed. |
| 36 | Use and waste formwork to sides and soffits of floor or roof beam, beam hunching, girder, lintels, cantilever, shelves including supports etc for rough finished flat surfaces of concrete complete all as specified and directed |
| 37 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 38 | Use and waste formwork to edges of concrete flats,slabs etc incl fair finished surfaces exe 5cm but n.exe 10cm wide all as specified nd directed. |
| 39 | Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 40 | Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and directed. |
| 41 | Material and labour for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20mm aggregate as in slab supported on walls , beams, and column in floors, roof, landing, balconies, canopies, deck slab and in shelves and like etc comlpete all as specified and directed. |
| 42 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 43 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in column, pillars, piers, posts, and struts complete all as specified and directed. |
| 44 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5m complete all as specified and directed. |
| 45 | M & L for Mild Steel TMT Bar 10mm dia and over, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 46 | M & L for Mild Steel TMT Bar 6mm to 8mm dia, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 47 | M & L for Mild Steel TMT Bar 6mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed |
| 48 | M & L for brickwork with subclass 'B' or locally available best quality old size bricks, straight or curved on plan exc 6 m mean raduis, built in CM (1:6) complete all as specified and directed. |
| 49 | M & L for brick work as half brick thick wall in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks complete all as specified . |
| 50 | M & L rendering 10mm thick cement mortar (1:6) on other than fair faces of brick wall or concrete surfaces, finished fair and even without using extra cement complete all as specified. |
| 51 | M & L rendering 10mm thick in cement mortar 1:6 on other than fair faces of brick wall or concrete surfaces, finished even and smooth without using extra cement complete all as specified. |
| 52 | M & L 15 mm thick rendering in cement mortar (1:4) on fair faces of brick wall or concrete surfaces, in two layer each of 10+5 mm thick & water proofing compound mixed with second layer @ 3% finished fair and even complete all as specified. (Note :WPC measured separately). |
| 53 | Supply only integral water proofing compound WPC complete all as specified. |
| 54 | M & L Non Skid ceramic tiles coloured 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry as specified |
| 55 | M & L Non Skid ceramic tiles coloured 8 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm and not exceeding 0.18 sqm as in skirting including 10mm thick screed bed or backing coat in cement mortar 1:4 laying of skirting/dado on walls all as specified and directed. |
| 56 | M & L Non Skid ceramic paver tiles coloured 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry complete all as specified. |
| 57 | M & L Glazed ceramic coloured tiles in vertical surface size 450mm x 350mm x & ( 6mm to 7mm )mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick screed bed or backing coat in cement mortar 1:4 laying of skirting/dado on walls all as specified and directed. |
| 58 | M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid over 20mm thick screed bed in cm 1 : 3 with cement slurry @ 4 kg/sqm jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing to achieve mirror/granite finish complete all as specified and as directed. |
| 59 | M&L in repairs for 18-20mm thick granite stone slab, of any type, table rubbed and polished, in steps, jambs, pillars, window cills, cooking platforms and the like in laid over and including 15mm thick screed in cement mortar (1:4) (rate shall be included) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab and taking off old damaged slab and disposing off complete all as specified and as directed. |
| 60 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 61 | S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 62 | Supply and fix Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 63 | S & F of mild steel rolled sections (Fe-290, Gde E-165) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and other misc brackets ; fixed with angle cleats for fixing of eaves board or other connecting plates complete all as specified. |
| 64 | S&F Roof trusses (framed), trussed,purlins, crane gantries, rails ,posts and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats nuts bolts plates (plain or chequered) etc. |
| 65 | S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one or more rebates including hinges (100/50mm stainless steel),lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified. |
| 66 | S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates including hinges (100/50mm stainless steel),lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified. |
| 67 | M & L Plain Cement concrete (1:3:6), type C-0 using 12.5mm graded stone aggregate as in filling of steel chowkhats and concrete for fixing of holdfast including necessary form work complete all as specified. |
| 68 | S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, smooth finish with lipping of teak wood on edges all as specified and directed |
| 69 | M & L Second class hard wood as in 35 mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified & directed . |
| 70 | S&F 2nd class hard wood glazed and skeleton door shutters 35 mm thick open rebated and prepared to receive glass, guage etc (withoput sash bars), edge of framing plain chemfered ro rounded fitted with cut and mitred beds for securing glass etc size of members of shutter as specified in SSR Part I section 8 clause 8.20(a) |
| 71 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge |
| 72 | Supply and fix Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 73 | S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putting square nexc 0.5 sqm in each pane complete all as specified. |
| 74 | S & F 150 mm long aluminium anodised alloy handles fabricated type complete all as specified & directed . |
| 75 | Supply and fix 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 76 | S&F double action spring hinges, mild steel with steel wire spring, stove enamelled, black, size of spring hinge 150mm complete all as specified and as directed. |
| 77 | Supply and fix 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 78 | S&F as in repairs 25 mm dia and 1mm thick MS chromium plated curtain rods with fixing side fancy type brackets end knobs & steel screws etc all as specified and directed . |
| 79 | Supply and fix, as in repair, vitreous china wash basin, white flat back size 550mm X 400mm, excluding taps, waste chain, plug and porcelain stopper but including cp coupling, brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified. |
| 80 | S&F in repair PVC connections 15mm dia size with PTMT nuts of length 450mm fixed with pipeline complete in all respect as specified. |
| 81 | S & F soap dish chromium plated standerd quality fixed on wall with brass screw complete all as specified. |
| 82 | S & F in repairs 15mm bore pillar tap cast copper alloy with capstan head,chromium plated concealed screwed down high pressure with or without hot or cold with long shunk screwed shanks and fly nuts screwed for iron pipes and connecting to water pipe line complete all specified and directed. |
| 83 | S&F in repairs 15mm bore bib taps fancy type, long neck, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including accessories complete all as specified and directed. |
| 84 | Supply and fix in repairs 15mm bore stop valves/angle valve of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) fixed complete all as specified. |
| 85 | S & F as in repair bevelled edge mirror complete all as specified and directed.Make : Modiguard, Saint Gobain or equivalent |
| 86 | S & F in repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs complete all as specified. |
| 87 | Supply and fix stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc.,overall size 495mm x 420 mm with bowl size 410mm x 330mm x 160mm etc complete all as specified and as directed. |
| 88 | Supply and fix as in repairs, 40 mm dia and 800mm long PVC flexible corrugated waste pipe for wash basin/sink with fittings complete all as specified and as directed. |
| 89 | S & F 75mm bore PVC (SWR) pipes single socketed with rubber joint, in any length fixed to walls / floors or in trenches complete all as specified. |
| 90 | S & F 75mm bore PVC (SWR) bends suitable for pipe complete all as specified. |
| 91 | S&F 15mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed. |
| 92 | Cutting chases, pinning in, making good to facing where required and pointed in cement mortar 1:3 and making good cutting exceeding 10 cm girth complete all as specified. |
| 93 | Material and labour for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system) of grid size 600mmx600mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick high Pressure high pressure Non Asbestos Fiber Cement decorative Board (E-Board Classic) in a grid of GI system duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purline from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinkler, smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall, flush fiiting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, as to form 600 mm x 600 mm grid and incl apply coloured painting work with two coat of acrylic emulsion paint over a coat of cement primer before installing it on the grid all as specified and directed. Make : Everest Industries Ltd or equivalent as per IS 14862 all as specified and directed. |
| 94 | M & L for preparation of new or previously untreated wall surfaces and applying three coats of white wash complete all as specified and directed. |
| 95 | M & L preparation of new plastered surface of walls and applying two coat of oil emulsion distemper over one coat of primer with using roller complete all as specified. |
| 96 | Material & Labour for preparation of old plastered surface applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using roller complete all as specified and directed. |
| 97 | M & L preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 98 | M & L for preparation of new wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coat of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 99 | M & L preparation of old steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 100 | E & M Division items |
| 101 | Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed. |
| 102 | Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed. |
| 103 | Dismantling old unserviceable main switches, sheet metal enclosures DB including MCBs etc and removing from site for taking credit incl making good to disturbed surface of wall as per existing specification complete all as specified and as directed. |
| 104 | Dismantling of U/s GI pipe of size 40 mm/50mm bore complete all as specified and directed. |
| 105 | Taking out old U/s XLPE cable of any size/type taking out of olf bricks/cable cover complete all as specified and directed. (Excavation and earth work will be measured and paid separately under respective items) |
| 106 | Taking out old U/s GI PIPE of 25 to 32mm size/type including all GI fittings etc complete all as specified and directed. (Excavation and earth work will be measured and paid separately under respective items) |
| 107 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty,concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 108 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch 5 Amp. |
| 109 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on the same board. |
| 110 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on independent board. |
| 111 | M & L for point wiring with FRLSH stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for 3 pin, 15 Amp socket outlet, independent |
| 112 | M&L for point wiring with FRLSH stranded copper conductor 4.0 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit concealed type of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 4.0 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for one power point on independent board of AC/equipments etc controlled by one SP/SPN MCB. Note: The point wiring will be done from DBs to the switch sockets of any size with three wires running independently for each point and with no tappings. |
| 113 | S&F switch piano flush type button single pole one way 5 Amps all as specified and directed. |
| 114 | S&F socket outlet 2 in 1, 3 pin 5 Amp flush type all as specified and directed. |
| 115 | S&F switch socket combination 5 in 1 5/16 Amp flush type with all as specified and directed. |
| 116 | S&F ceiling rose surface bakelite with three terminals all as specified and directed |
| 117 | S&F ceiling fan regulator socketed, step type, flush type heavy duty suitable to work on 230 volts Ac supply complete all as specified. |
| 118 | S&F lamp angular holder insulated body with back plate complete all as specified. |
| 119 | M & L for submain wiring with two single core 6.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid Conduit conceled with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 6.0 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLSH connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 120 | Supply & Fix LED betten plastic type fitting of capacity 20W, wall mounted, operating on 230V, 50Hz, AC Supply having luminous efficiancy not less than 125 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long with decorative end caps elegently designed complete all as specified. |
| 121 | S & Fing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type down lighter with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 122 | S & F LED decorative light fitting made up of polycarbonate, suitable for 9W LED lamp B22 base, classic wal light suitable for living / bed room, antique surface sleek of approved design with 9W LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.Make: Cat Part No. LHDL06160099 of Havells or equivalent |
| 123 | S & Fing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.. |
| 124 | S&F LED bulb 9watt, BEE 5 star rated provide upto 4 hours power backup and connecting to lamp holder complete all as specified and directed.Make - B22/E27-CDL/WW 10 watt of Crompton or equivalent as approved list of make |
| 125 | S&F 25 watt bldg security light, LED luminaire IP 66 LED lamp, made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge. Make : Crompton Cat No- LSTS-25-CDL/NL-M of Crompton or equivalent as per approved make list. |
| 126 | Supply & fix Wall mounting fan 400 mm sweep, operating on single phase, 230V, AC, 50 Hz having speed of 1400 RPM, air delivery 115 CMM, power output of 100W star rated along with blade, canopy, mounting brackets, rubber insulator complete all as specified and directed. |
| 127 | S&F BLDC ceiling fan 1200mm sweep complete with blades, down rods and accessories, 230 V, min air delivery 210 CFM with service value 6.00 BEE 5 star rated & provn of ‘S’ type fan hook including taking down of old UNSV one and depositing to MES storeyard for keeping in safe custody complete all as specified and directed. |
| 128 | S&F plastic body exhaust fan 250mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed. |
| 129 | S&F Metal steel body exhaust fan 380 mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces including taking down of old UNSV one and depositing to MES storeyard for keeping in safe custody complete all as specified and as directed. |
| 130 | S & F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc complete all as specified and as directed. |
| 131 | S&F moduler type 3/5 pin socket with one single pole MCB 20Amp 230Volts including concealing in wall suitable for geyser, AC and domestic applianes complete all as specified and directed. |
| 132 | S&F sheet metal enclosure powder coated three phase and neutral (TPN) DB for fixing of MCBs, 4 way double door with aluminum bus bar 100 Amp including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 133 | S&F sheet metal enclosure powder coated single phase and neutral (SPN) DB for fixing of MCBs, 8 way double door with Aluminum bus bar 100 Amp including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 134 | S&F MCB TPN of capacity 63 Amps, 240 V, 10 KA 'B' curve complete all as specified and directed. |
| 135 | S&F MCB SPN of capacity 40-63 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 136 | S&F MCB SP of capacity 5-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 137 | Taking out old existing earthing and M & L for new earthing with galvanised steel earth plate electrode 600mm X 600mm X 6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed. |
| 138 | Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 35 sqmm 3.5 core laid in trenches/fixed to wall/under road/pipe etc with copper cable glands & copper thimbles complete all as specified and directed. |
| 139 | S & F GI tube light grade 40mm bore with fittings for protection of cable complete all as specified and directed. |
| 140 | S & F for steel water tubing 25mm dia, medium grade galvanised with new fitting laid in trenches or on wall complete all as specified and directed. |
| 141 | S&F gun metal gate valve 25mm dia, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed. |
| 142 | M & L PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate for flooring complete all as specified and directed. |
| 143 | M & L for cutting of existing GI pipe line 25mm dia for inserting Tee and reducer etc for taking 25mm dia branch pipe including fittings complete |
| 144 | Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed. |
| 145 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed. |
| 146 | Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed. |
| 147 | M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge.Note : Thickness of sand cushioning after punning down will be measured. |
| 148 | M&L for bricks sub-class 'B' laid in trenches in flat style (width portion in horizontal shape) for cable protection complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender