Tender For Special Repair To Boundary Wall, Boundary Fence, Entrance Gate And Special Repair To Drainage And Sewerage System At Different Location And Repair Of Hardstanding At Lichubari Under Ge Jorhat.
Tender Value
39.63 Lakhs
Estimated cost
Bid Submission
12 Sep 2026
15 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jorhat → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Boundary Wall, Boundary Fence, Entrance Gate And Special Repair To Drainage And Sewerage System At Different Location And Repair Of Hardstanding At Lichubari Under Ge Jorhat.
BOQ
| Sl. No. | Item Description |
| 1 | NOTE:-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.(ii) It is highlighted that the certain condition of General Condition of Contracts (IAFW-2249) has been modified as per direction of MoD i.e. inclusssion of Performance Security, deletion of Risk & Cost Provisions and increase in defect liability period all as per tender documents. The tenderers should keep in mind while quoting their offer. (iii) (Applicable for all items/parts):- The bidders/contractors are advised to refer Notes on BOQ/SCH'A' before entry/quoting the rates. |
| 2 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 4 | Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and as directed. |
| 5 | Demolition of cement concrete (reinforced) of any description and any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) and removal of rubbish from the site complete all as specified and as directed. |
| 6 | Demolition of cement concrete of (unreinforced) any description and any position not otherwise specifically provided for and removal of rubbish from the site complete all as specified and as directed. |
| 7 | Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided for and segregating serviceable materials and keeping for reuse at site and removing unserviceable materials from site of work complete all as specified and as directed. |
| 9 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion from Concrete, brick work, masonry, etc. and making good to disturbed ground as in natural ground/ concrete level complete all as specified and as directed. |
| 10 | Dismantling fencing wire mesh, any type (Galvanised/ Steel barbed wire) complete all as specified and as directed. |
| 11 | Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundations or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10Sqm on plan and not exceeding 1.50m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 12 | Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50m and making good disturbed surface in any type of soil complete all as specified and as directed. |
| 13 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm on soft/loose soil complete all as specified and as directed. |
| 14 | Removing excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed. |
| 15 | Material and labour for hardcore of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 16 | Material and labour for providing cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 17 | Material and labour for providing cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 18 | Material and labour for providing cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 19 | Material and labour for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in surface channel, drains and like etc. complete all as specified and as directed. |
| 20 | Material and labour for plain cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in roof kerb or mud stops, rounded or chamfered on edges complete all as specified and as directed. |
| 21 | Material and labour for PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary use and waste of formwork complete all as specified and as directed. |
| 22 | Material and labour for reinforced cement concrete 1:2:4 type B1 (Nominal Mix) (using 20mm graded stone aggregate) as in footing, foundation beam, bases of column plinth beams, etc complete all as specified and as directed. |
| 23 | Material and labour for reinforced cement concrete 1:2:4 type B1 (Nominal Mix) (using 20mm graded stone aggregate) as in as in column, pillars, piers, posts and struts complete all as specified and as directed. |
| 24 | Material and labour for reinforced cement concrete 1:2:4 type B1 (Nominal Mix) (using 20mm graded stone aggregate) as in beams, cantilevers, lintel over 1.50m span complete all as specified and as directed. |
| 25 | Material and labour for providing precast cement concrete (1:2:4), type B-1, (using 20mm graded aggregate) as in landings, cover slabs(for manholes, etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:4) including necessary use and waste of form work complete all as specified and directed.Note: Reinforcement shall be measured and paid seperately under respective item. |
| 26 | Material and labour for 100mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base floring and finish the surface fair and even complete all as specified and as directed. |
| 27 | Material and labour required extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed. |
| 28 | .-Ditto- all as per item No 13.00 above but add or deduct for each 25mm girth or part there of over or under 30cm and -ditto-. |
| 29 | Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and as directed. |
| 30 | Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:4) complete all as specified and as directed. |
| 31 | Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter with rough finished flat surface complete all as specified and as directed. |
| 32 | Material and labour for flat formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished flat surface complete all as specified and as directed. |
| 33 | Materials and labour for use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bres-summers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished flat surfaces of concrete complete all as specified and as directed. |
| 34 | Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. |
| 35 | Material and labour for mild steel TMT bars 6 to 8mm dia, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. |
| 36 | Material and labour for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing, conforming to Fe 410 W (Gde-E-250) quality A complete all as specified and as directed. |
| 37 | Supply and fixing rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250 quality-A) complete all as specified and as directed. |
| 38 | Materials and labour for mild steel fencing posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 39 | Material & Labour for Mild steel screw bolts 5mm to 10mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm and not exceeding 10cm long complete all as specified and as directed. |
| 40 | Fixing only Chain link fencing 4mm dia galvanised steel wire,100x100mm mesh, made up into mattresses or cages, lapped, wired and laid/fixed in position, including line wires, any mesh, any size,any type of standards rails straining bolts etc including provisioning of binding wires complete all as specified and directed. |
| 41 | Supply only Chain link fencing 4mm dia GI wire netting having mesh size of 100x100mm, made up into mattresses or cages, lapped, wired and laid/fixed in position complete all as specified and directed. |
| 42 | Supply and fixing galvanised. 2 strand, steel barbed wire 2.24mm dia. barbed with 2mm dia. barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as in repair complete all as specified and as directed. |
| 43 | Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed. |
| 44 | Material and labour for glazed ceramic coloured tiles (Premium Quality) of size 350x250x7mm/ 450x350x 7mm thick as on vertical surfaces, set and jointed in neat cement slurry and pointed in white cement with pigment to match with the shade of tiles laid over and including 10mm thick cement plaster in CM (1:4) complete all as specified and as directed. |
| 45 | Material and labour for machine pressed precast cement concrete interlocking paver blocks 80mm thick and M 40 Grade confirming to IS-15658-2006 and laid over and including 25mm thick sand cushioning complete all as specified and as directed. |
| 46 | Material and labour for Granite work (of any type) 20 mm thick (table rubbed and polished) in slab, jambs,pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade complete all as specified and as directed. |
| 47 | Materials and labour for 15 mm thick rendering on brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 48 | Materials and labour for 15 mm thick rendering on fair faces of brick work in cement mortar (1:4) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 49 | Materials and labour for 15 mm thick rendering other than fair faces of brick work in cement mortar (1:4) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 50 | Material and labour for applying two coats of cement base paint over a coat of primer including preparation of newly plastered surfaces of wall complete all as specified and as directed. |
| 51 | Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 52 | Material and labour for preparation of new steel surfaces of any description not exceeding 10 cm width or girth and applying two coats of synthetic enaeal paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 53 | Material and labour for PCC 1:3:6, type C2, (using 40mm graded stone aggregate) as in concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 300mm bore of pipe complete all as specified and as directed.Note: Pipes shall be measured and paid seperately. |
| 54 | Material and labour for 300mm bore Reinforced concrete pipes, class NP2, laid and jointed with collars, laid in trenches on concrete bed to required slope complete all as specified and as directed.Note: Earthwork and concrete bed shall be measured and paid seperately. |
| 55 | Supply and fixing as in replacement 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 56 | Supply and fixing (3D) bright-finished stainless steel letters, fabricated from 1.0 mm thick Grade 304 stainless steel sheet, of required shape and size, 300 mm high and 250 mm wide, including cutting, forming, bending, welding/spot welding, grinding and finishing, necessary fixing brackets/fasteners, and securely fixing the letters to existing granite cladding in the required alignment and spacing, complete with all necessary materials, labour, tools and accessories, all as specified and as directed. |
| 57 | Supply and fixing (3D) aluminium anodised RHINO crest, approximately 600 mm diameter, fabricated from suitable aluminium sheet/section of adequate thickness and rigidity, in the required three-dimensional profile and finish, including cutting, forming, fabrication, necessary stiffening/supports, approved fixing accessories and securely fixing the crest to existing granite cladding with suitable concealed/approved mechanical fasteners, complete in all respects, all as specified and as directed. |
| 58 | Supply and fixing 5 mm thick rigid acrylic sheet, versatile, lightweight, shatter-resistant and impact-resistant, of approved make, colour and finish, cut to required size and shape, including drilling/cutting of holes, necessary edge finishing, and fixing to the existing MS framework with suitable approved screws, washers, spacers, clips or other fixing accessories, including all necessary cutting, fitting, alignment and making good, complete in all respects, all as specified and as directed. |
| 59 | Supply and fixing as in replacement MCB DB TPN 4 ways double door with MCB TPN incommer including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and as directed.Note:- MCB TPN, MCB SPN and MCB SP shall be measured and paid seperately under respective item. |
| 60 | Supply and fixing as in replacement MCB TPN, 240 Volts, of 63 amps current rating, 10 KA breaking capacity ‘C' series complete all as specified and as directed. |
| 61 | Supply and fixing as in replacement MCB SP, 240 Volts, of 6-32 amps current rating, 10 KA breaking capacity ‘C' series complete all as specified and as directed. |
| 62 | Supply and fixing sub-main wiring with PVC insulated & unsheathed two run of 2.5 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of 2.5 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly as earth continuity conductor, drawn through 20 mm conduit/ Casing Caping with all accessories and PVC rectangular boxes for mounting switch socket and fan regulator etc including taking down old sub-main wiring complete all as specified and as directed.Note : Three runs of 2.5 Sqmm cable and conduit shall be measured as one unit. |
| 63 | Supply and fixing as in replacement Compact street lighting luminaires with deep drawn housing for single 70 Watt LED, 5700K with toughened glass protection, pressure die cast aluminium housing IP66,with epoxy white powder coated and fixing bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length 1.2 mtr,fixed over the vertical wall through two numbers mild steel clamp of 25mm width, 3mm thick MS flat strip and four Nos nuts, bolts & washers of 12mm dia, 150mm long grouted into wall complete all as specified and as directed. |
| 64 | Supply and fixing as in replacement asymmetrical LED flood light luminaires, 200 watt, 230 Volt, 50 Hz, LED 5000K, IP66 Metal Halide, grey powder coated die-cast aluminium lamp housing, bult-in control gear, faceted anodised aluminium reflector heat resistant toughened clear glass cover complete including connecting and testing all as specified and as directed. |
| 65 | Supply and fixing as in replacement 20 Watt LED post top (white colour), 230 volt, 360 degree made in cast aluminium spigot housing with decorative opal acrylic diffuser and IP65 protection including fixing with LED driver and lamp complete all as specified and as directed. |
| 66 | Supply and fixing as in replacement 100 Watt LED High Bay Light, suitable for industrial/high-bay applications, comprising high-pressure die-cast aluminium housing with suitable heat-sink arrangement and integrated UV-stabilised polycarbonate optical lens/cover, having minimum IP66 degree of protection, complete with both cradle-type mounting bracket and eye-bolt suspension arrangement, including suitable additional safety chain/wire rope for secondary support. The luminaire shall have a system efficacy of not less than 130 lumens/Watt, with suitable LED optics for uniform illumination. The LED driver shall be BIS-approved, silicon-filled/potted type, with suitable built-in surge protection of minimum 4 kV and additional external surge protection of minimum 10 kV, or as recommended by the OEM, complete with all necessary internal wiring, connectors and accessories. The luminaire shall have THD ≤ 10%, power factor ≥ 0.95 and CCT 5700 K, unless otherwise specified. The make, model and unique identification details shall be permanently embossed/engraved or otherwise indelibly marked on the luminaire for traceability throughout its service life. The luminaire shall be supplied with a photometric test report conforming to LM-79, issued by an NABL-accredited laboratory or laboratory recognised by the competent authority, wherever specified. Relevant LED performance/test certificates and manufacturer's technical data shall also be submitted for approval. The item shall include OEM warranty for a minimum period of 5 years from the date of supply/commissioning, supported by a warranty certificate issued on the OEM's letterhead and submitted at the time of delivery. The rate shall also include provision of ladder/access equipment suitable for working up to 16 m height, including transportation, erection, fixing, alignment, testing and commissioning, all necessary tools, tackles, lifting arrangements, fasteners and accessories, complete in all respects, all as specified and as directed. |
| 67 | Supply and laying GI tubing 40mm bore light grade with fittings laid in trenches or for road crossing for protection of LT underground cables including taking up old unserviceable pipe complete all as specified and as directed. |
| 68 | Material and labour for HDPE pipe of pressure rating 10 kgf/cm² and dia 25 mm for passing of cable through PCC foundation from trench to distribution board with necessary clamp nuts and bolts complete all as specified and as directed. |
| 69 | Labour only for boring of hole under roads with mechanical arrangement upto 50 mm dia without disturbing the top surface of the road for passing the cable across the road complete all as specified and as directed. |
| 70 | Supply and laying under ground XLPE insulated PVC sheathed (Heavy duty) armoured 1100 volts grade aluminium conductor cable of size 35 Sqmm 3.5 core laid in trenches as per IS 7098 (Part I) including connection cable glands, aluminium lugs etc. and replaement of old unserviceable cable complete all as specified and as directed. |
| 71 | Supply and laying under ground XLPE insulated PVC sheathed (Heavy duty) armoured 1100 volts grade aluminium conductor cable of size 25 Sqmm 4 core laid in trenches as per IS 7098 (Part I) including connection cable glands, aluminium lugs etc. complete and replaement of old unserviceable cable complete all as specified and as directed. |
| 72 | Supply & fixing Three core 1.5sqmm (nominal area) service wire PVC insulated copper conductor FRLS, multi stranded, unsheathed 1100 volts grade IS-694 marked for connection from junction box to street light fitting through steel pole with necessary clamps, bolts, etc required for fixing complete all as specified and as directed. |
| 73 | Supply and fixing as in replacement steel tubular swaged poles, type 410 SP 31 (Overall length 9.00 meter) conforming to IS-2713 (Part 1 to 3) 1980 complete with cast iron base plate, finial taper plug, bolts, nuts and washers, screws. Pole shall be painted with two coat of black bituminous throughout internally and externally upto planting depth and the remaining external portion shall be painted with two coats of aluminum paints over a coat of red oxide primer, painting black & white alternate strips of 30cm each externally from ground level upto 1.2m with synthetic enamel paint, numbering of poles complete all as specified and as directed.Note: Excavation and earth work and PCC shall be measured and paid separately under respective items. |
| 74 | Supply and fixing as in replacement Polycarbonate weatherproof junction Box IP 69 thermoplastic with size 300mm x 300mm x 150 mm or nearest higher size made of polycarbonate with IP 65 degree of protection (EN60529), dust proof, water tight, shock proof, fire retardant, with internally embedded gasket fitted with heat treated Bakelite for terminals block and PVC Glands for cable entry complete all as specified and as directed. |
| 75 | Material and labour for sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 cm in depth after laying the Cable) and consolidated (punned) upto 18 cm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only shall be measured and paid for. |
| 76 | Material and labour for Brick with subclass 'B' bricks in cable protection, laying with built in each other complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysSep 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender