Tender For Addition / Alteration To Trg Shed Covered With Galvalume Sheet 25X 10 Mtr Near Basketball Court And Provn Of 01 X Modern Toilet Block At Lichubari Under Ge Jorhat.
Tender Value
45.36 Lakhs
Estimated cost
Bid Submission
12 Sep 2026
19 days left
EMD
91000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jorhat → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition / Alteration To Trg Shed Covered With Galvalume Sheet 25X 10 Mtr Near Basketball Court And Provn Of 01 X Modern Toilet Block At Lichubari Under Ge Jorhat.
BOQ
| Sl. No. | Item Description |
| 1 | NOTE:-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.(ii) It is highlighted that the certain condition of General Condition of Contracts (IAFW-2249) has been modified as per direction of MoD i.e. inclusssion of Performance Security, deletion of Risk & Cost Provisions and increase in defect liability period all as per tender documents. The tenderers should keep in mind while quoting their offer. (iii) (Applicable for all items/parts):- The bidders/contractors are advised to refer Notes on BOQ/SCH'A' before entry/quoting the rates. |
| 2 | Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc. complete all as specified and as directed. |
| 3 | Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. |
| 4 | Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed. |
| 5 | Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundations or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10Sqm on plan and not exceeding 1.50m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 6 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm on soft/loose soil complete all as specified and as directed. |
| 7 | Removing excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed. |
| 8 | Material and labour for hardcore of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 9 | Material and labour for moorum/red bajri, filling in road side berm laid in layers not exceeding 150mm spread thickness, spread, rolled and consolidated to gradient and camber required complete all as specified and directed. |
| 10 | Material and labour for providing cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 11 | Material and labour for PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary use and waste of formwork complete all as specified and as directed. |
| 12 | Material and labour for reinforced cement concrete 1:2:4 type B1 (Nominal Mix) (using 20mm graded stone aggregate) as in footing, foundation beam, bases of column plinth beams, etc complete all as specified and as directed. |
| 13 | Material and labour for reinforced cement concrete 1:2:4 type B1 (Nominal Mix) (using 20mm graded stone aggregate) as in as in column, pillars, piers, posts and struts complete all as specified and as directed. |
| 14 | Material and labour for reinforced cement concrete 1:2:4 type B1 (Nominal Mix) (using 20mm graded stone aggregate) as in beams, cantilevers, lintel over 1.50m span complete all as specified and as directed. |
| 15 | Material and labour for 100mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base floring and finish the surface fair and even complete all as specified and as directed. |
| 16 | Material and labour for 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in sub base floring and finish the surface even and smooth without using extra cement complete all as specified and as directed. |
| 17 | Material and labour for 40mm thick PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in sub base floring and finish the surface even and smooth without using extra cement complete all as specified and as directed. |
| 18 | Material and labour for 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, paving, footpath etc and finished the surface even and smooth without using extra cement laid in panels including joint filled with sealing compound complete all as specified and as directed. |
| 19 | Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and as directed. |
| 20 | Materials and labour for half brick thick brick work with old size sub class 'B' bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and as directed. |
| 21 | Material & labour for cutting chases for concealed water tubing, cutting not exceeding 10cm girth and make the surface good as per existing with cement morter 1:3 complete all as specified and as directed |
| 22 | Materials and labour for use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bres-summers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished flat surfaces of concrete complete all as specified and as directed. |
| 23 | Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter with rough finished flat surface complete all as specified and as directed. |
| 24 | Material and labour for flat formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished flat surface complete all as specified and as directed. |
| 25 | Supply and fix 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Sec-tion 8, clause 8.24 (a) complete all as specified and as directed. |
| 26 | Supply and fixing for 30mm thick factory made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified and as directed. |
| 27 | Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. |
| 28 | Material and labour for mild steel TMT bars 6 to 8mm dia, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. |
| 29 | Material and labour for mild steel works as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed. |
| 30 | Supply and fix framed work such as grills, grating, etc, with ends of bars shouldered and/or riveted or forged into spikes ; window framed gurad bars ; barred iron doors, laddrs, framed balasters, walk ways, railings framed work of water and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 31 | Supply and fixing steel work in tubular trusses i.e truss bottom, top bend, sides, side supports, holding plates, posts and base plate etc. including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 etc complete all as specified and as directed. |
| 32 | Supply and fixing rolled mild steel joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-410-W (Gde-E-250 quality-A) complete all as specified and as directed. |
| 33 | Supply and fixing rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250 quality-A) complete all as specified and as directed. |
| 34 | Material & Labour for Mild steel screw bolts 5mm to 10mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm and not exceeding 10cm long complete all as specified and as directed. |
| 35 | Supply and fixing steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, MS 10mm squrare guard bar, Glazing bar dovetailed or welded for receiving glass and including cutting holes in wall for fixing the window with hold fast in PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) and makding good the disturbed surfaces in CM (1:4) and with the existing finishes to match complete all as specified and as directed. |
| 36 | .-Ditto- all as per item No 34.00 above but without glazing bar and -ditto-. |
| 37 | Supply and fixing pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,complete all as specified and as directed. |
| 38 | Supply and fixing Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators etc with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed |
| 39 | Supply and fixing Anodised powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed. |
| 40 | Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed. |
| 41 | Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed. |
| 42 | Supply and fixing 4mm thick HSPC (High Pressure Steam Cured) board as in false ceiling with powder coated GI/aluminium snap grid/section of size 600mm x 600mm fixed to wall hanging from soffits/trusses using adjustable supporting hanger comprising of 4mm dia MS rod or wire ‘J’ type hook, nuts, bolts, holding down clips with GI/aluminium section of size 36.5mm x 25mm x 1.4mm (main tee) and 23.5mm x 26.4mm x 1.4mm (cross tee) and wall angle of size 25mm x 25mm x 1.4mm complete all as specified and as directed. |
| 43 | Supply and fixing 4.00 mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed. |
| 44 | Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed. |
| 45 | Supply and fixing Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing etc. complete all as specified and as directed. |
| 46 | Supply and fixing 100mm size stainless steel butt hinges complete all as specified and as directed. |
| 47 | Supply and fixing aluminium anodized, barrel tower bolts, 200mm long of extruded section complete all as specified and as directed. |
| 48 | Supply and fixing 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 49 | Supply and fixing 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 50 | Supply and fixing for 300mm long mild steel ordinary rat tail rod pattern springs for doors including roller and roller plate complete all as specified and as directed. |
| 51 | Supply and fixing friction less Stainless Steel Roller 304 grade for sliding Board/racks complete all as specified and as directed. |
| 52 | Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. |
| 53 | Material and labour for non skid ceramic coloured tiles (Premium Quality) 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 54 | Material and labour for non skid ceramic coloured tiles (Premium Quality) 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 55 | Material and labour for glazed ceramic coloured tiles (Premium Quality) of size 350x250x7mm/ 450x350x 7mm thick as on vertical surfaces, set and jointed in neat cement slurry and pointed in white cement with pigment to match with the shade of tiles laid over and including 10mm thick cement plaster in CM (1:4) complete all as specified and as directed. |
| 56 | Materials and labour for 15 mm thick rendering on brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 57 | Materials and labour for 5 mm thick rendering on concrete surfaces in ceiling in cement mortar (1:3) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 58 | Supply only integral water proofing compound conforming to IS-2645 complete all as specified and directed. |
| 59 | Material and labour for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade `A' complete all as specified and as directed. |
| 60 | Materials and labour for preparation of new plastered surfaces of walls and applying Acrylic Smooth exterior paint (Weather Coat) 1st quality of required shade (Two coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) over and including complete all as specified and as directed. |
| 61 | Materials and labour for preparation of newly plastered surfaces of wall and applying two coats of acrylic washable distemper over a coat of primer over and including 2mm thick wall care putty complete all as specified and as directed. |
| 62 | Material and labour for applying two coats of cement base paint over a coat of alkali resistant primer including preparation of newly plastered surfaces of wall complete all as specified and as directed. |
| 63 | Material and labour for applying two coats of cement base paint over a coat of primer including preparation of newly plastered surfaces of wall complete all as specified and as directed. |
| 64 | Material and labour for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 65 | Material and labour for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 66 | Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 67 | Material and labour for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 100mm dia of pipe complete all as specified and as directed. |
| 68 | Supply and laying 25mm bore galvanised steel water tubing medium grade including all fittings and laid in trenches complete all as specified and as direcetd. |
| 69 | Supply and fix 20mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd. |
| 70 | Supply and fix 15mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd. |
| 71 | Material and labour for Cutting existing steel tubing of 40mm dia for alterations or additions (Each cut measured) complete all as specified and as direcetd. |
| 72 | Supply and fixing 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 73 | Supply and fixing 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with suitable size of MS flat iron clamp complete all as specified and as directed. |
| 74 | Supply and fixing 110 mm bore PVC (SWR) bends any radius with oval access door complete all as specified and directed. |
| 75 | Supply and fixing 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, with oval access door complete all as specified and as directed. |
| 76 | Supply and fixing 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 77 | Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 1000 litres with and including 20mm bore PTMT float and ball valve set including providing necessary connections complete all as specified and as directed. |
| 78 | Supply and fixing vitreous China white wash down water closet pan (pedestal pattern) with ‘P’ or ‘S’ trap, front or back inlet, fixing bolts, with white PVC seat cover, jet spray and providing 32 mm dia PVC flush pipe and making all necessary connections complete as specified and as directed. |
| 79 | Supply and fixing Vitreous China urinals half stall type of size 460mm x 330mm x 250mm (minimum) with urinal spreader, grating and union for discharge pipe, 15mm dia PVC connection pipe 450mm long, CP waste coupling, 40mm dia waste pipe 600mm long high density polyethylene(HDPE) pipes of pressure rating 6 kgf/sq.cm complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinals to plugs with and including 60mm long brass screws, pointing around urinals back in cement complete all as specified and as directed. |
| 80 | Supply and fixing Vitreous china urinal partition white of size 310x700 mm complete all as specified and as directed. |
| 81 | Supply and fixing vitreoues china WHB, white, flat back, of size 550X400mm including CP brackets, CP waste coupling 32 mm bore, PVC waste pipe 32mm dia with and including 15mm bore PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and as directed. |
| 82 | Supply and fixing looking mirror of size 600mm x 450mm x 5mm thick bevelled edge of selected quality glass, decorative type mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 83 | Supply and fixing 15mm bore fancy type 2 way bib taps cast copper alloy chromium plated twin -leaver operated, with built in areator and wall flange screwed to pipe complete all as specified and as directed. |
| 84 | Supply and fixing 15mm bore stop valve, brass fancy type chromium plated, screwed down high pressure with crutch or butter fly handle screwed both ends fixed to GI pipe complete all as specified and as directed. |
| 85 | Supply and fixing 15mm bore fancy type angular stop cock made of brass chromium plated screwed both ends for pipe with crutch handle, screwed down, screwed for iron pipe complete all as specified and as directed. |
| 86 | Supply and fixing 15mm bore Chromium Plated pillar tap fancy type cast copper alloy, with capstan heads screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for pipe complete all as specified and as directed. |
| 87 | Supply and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed. |
| 88 | Supply and fixing soap dish holder brass chromium plated of approximate size 200x 200x90mm fixed to plugs with chromium plated brass screws complete all as specified and as directed. |
| 89 | Supply and fixing toilet paper holder brass chromium plated with stainless steel flap cover including necessary accessories complete all as specified and as directed. |
| 90 | Supply and fixing 25mm bore Gun metal Globe or gate valve with iron wheel head and gun metal spindle screwed both ends complete all as specified and as directed. |
| 91 | Supply and fixing 20mm bore Gun metal Globe or gate valve with iron wheel head and gun metal spindle screwed both ends complete all as specified and as directed. |
| 92 | Supply and 15mm dia PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed. |
| 93 | Material and labour for (concealed Type) point wiring including necessary chase cutting of wall for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit medium grade with all accessories and sunk modular GI box for mounting of fittings like switch, socket and fan regulator and making good the disturbed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge.Note: A. Red colored cable shall be used for live connection; black colored cable shall be used for neutral connection and green colored cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.B. The Rate of point wiring includes the following: - (i) Copper standard wire. (ii) PVC conduit with accessories. (iii) Chase cutting. |
| 94 | . -Ditto- all as per item No 92.00 here-in-before but for 3 pin 6 amps switch socket combination on the same board with 1.5 Sqmm cable and -ditto-. |
| 95 | . -Ditto- all as per item No 92.00 here-in-before but for 3 pin 6 amps switch socket combination on the independent board with 1.5 Sqmm cable and -ditto-. |
| 96 | . -Ditto- all as per item No 92.00 here-in-before but for one 6 pin multi, Modular socket outlet, 6/16 Amps, independent, with single core multi strand insulated unsheathed copper conductor 4.00 Sqmm FRLSH of size including single core multi strand unsheathed copper conductor 4.00 Sqmm FRLSH for earth continuity and connecting to common earth dolly and -ditto-. |
| 97 | Supply and fixing Metal flush box modular for 3 module complete all as specified and as directed. |
| 98 | Supply and fixing Metal flush box modular for 4 module complete all as specified and as directed. |
| 99 | Supply and fixing Metal flush box modular for 6 module complete all as specified and as directed. |
| 100 | Supply and fixing Metal flush box modular for 8 module complete all as specified and as directed. |
| 101 | Supply and fixing White cover plate with frame (both inner plate & outer plate cover),modular for 3 module complete all as specified and as directed. |
| 102 | Supply and fixing White cover plate with frame (both inner plate & outer plate cover),modular for 4 module complete all as specified and as directed. |
| 103 | Supply and fixing White cover plate with frame (both inner plate & outer plate cover),modular for 6 module complete all as specified and as directed. |
| 104 | Supply and fixing White cover plate with frame (both inner plate & outer plate cover),modular for 8 module complete all as specified and as directed. |
| 105 | Supply and fixing Modular type shuttered socket outlet 2/3 pin, 6 Amps, 230 volt, 2 Module complete all as specified and as directed. |
| 106 | Supply and fixing Modular type shuttered socket outlet 2/3 pin, 6/16 Amps, 230 volt, 2 Module complete all as specified and as directed. |
| 107 | Supply and fixing Modular switch single pole one way 6 Amps, 230 volt, 1 Module complete all as specified and as directed. |
| 108 | Supply and fixing Modular switch single pole one way 16 Amps, 230 volt, 1 Module complete all as specified and as directed. |
| 109 | Supply and fixing as in replacement step type electronic fan regulator 100/120 watt flush type AC 220 Volt complete all as specified and as directed. |
| 110 | Supply and fixing ceiling rose surface Bakelite three terminal complete all as specified and as directed. |
| 111 | Supply and fixing 1 X 12Watt, 230V LED Lamp with B-22 base, AC 230 Volt, 50HZ, 6500K suitable for holder fittings complete all as specified and as directed. |
| 112 | Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. minimum air delivery 210 CFM with service value 6.00 BEE. Five stars rated (Current Year) with brushless direct current motor (BLDC) (without Remote) complete all as specified and as directed. |
| 113 | Supply and fixing Exhaust fan steel body AC single phase 230 V of size 300 mm sweep with blades, frame & louvers including necessary hole for insertion of exhaust fan all as specified and directed.Note:– (i)The item rate is inclusive of making holes or making existing opening suitable for the installation of exhaust fan as per site condition all as specified and directed by Engr-in-chrg.(ii) The louvers for the exhaust fan shall be made of GI sheet suitable and properly fixed to the opening. |
| 114 | Supply and fixing MCB DB SPN 8 ways double door including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and as directed.Note:- MCB SPN and MCB SP shall be measured and paid seperately under respective item. |
| 115 | Supply and fixing MCB SPN, 240 Volts, of 32 amps current rating, 10 KA breaking capacity ‘C' series complete all as specified and as directed. |
| 116 | Supply and fixing MCB SP, 240 Volts, of 6-32 amps current rating, 10 KA breaking capacity ‘C' series complete all as specified and as directed. |
| 117 | Supply and fixing sub-main wiring with PVC insulated & unsheathed two run of 6 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of 6 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly as earth continuity conductor, drawn through 20 mm conduit/ Casing Caping with all accessories and PVC rectangular boxes for mounting switch socket and fan regulator etc. complete all as specified and as directed.Note : Three runs of 6 Sqmm cable and conduit shall be measured as one unit. |
| 118 | Supply and fixing as in replacement LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 119 | Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 120 | Supply and fixing LED mirror lights fitting 1x 10 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 121 | Supply and fixing Compact street lighting luminaires with deep drawn housing for single 35 Watt LED, 5700K with toughened glass protection, pressure die cast aluminium housing IP66,with epoxy white powder coated and fixing bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length 1.2 mtr,fixed over the vertical wall through two numbers mild steel clamp of 25mm width, 3mm thick MS flat strip and four Nos nuts, bolts & washers of 12mm dia, 150mm long grouted into wall complete all as specified and as directed. |
| 122 | Materials and labour as in replacement for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed. |
| 123 | Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed. |
| 124 | Materials and labour as in replacement for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised strip 25x4mm by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 40mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed. |
| 125 | Supply and laying GI tubing 40mm bore light grade with fittings laid in trenches or for road crossing for protection of LT underground cables including taking up old unserviceable pipe complete all as specified and as directed. |
| 126 | Supply and laying GI tubing 40mm bore light grade with fittings laid in trenches or for road crossing for protection of LT underground cables complete all as specified and as directed. |
| 127 | Labour only for boring of hole under roads with mechanical arrangement upto 50 mm dia without disturbing the top surface of the road for passing the cable across the road complete all as specified and as directed. |
| 128 | Supply and laying under ground XLPE insulated PVC sheathed (Heavy duty) armoured 1100 volts grade aluminium conductor cable of size 25 Sqmm 4 core laid in trenches as per IS 7098 (Part I) including connection cable glands, aluminium lugs etc. complete all as specified and as directed. |
| 129 | Supply and laying under ground XLPE insulated PVC sheathed (Heavy duty) armoured 1100 volts grade aluminium conductor cable of size 16 Sqmm 4 core laid in trenches as per IS 7098 (Part I) including connection cable glands, aluminium lugs etc. complete all as specified and as directed. |
| 130 | Supply & fixing Three core 1.5sqmm (nominal area) service wire PVC insulated copper conductor FRLS, multi stranded, unsheathed 1100 volts grade IS-694 marked for connection from junction box to street light fitting through steel pole with necessary clamps, bolts, etc required for fixing complete all as specified and as directed. |
| 131 | Supply , install, testing and commissioning as in replacement of cubical housing cabinet type CPRI approved Confirming to IP55 LT panel board outdoor type of size 0.75m x 0.60m x 0.60m, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 3.15 mm thick CRCA MS Sheet and built upon suitable size MS angle iron frame work, having front and rear hinged doors, lifting lugs (2 Nos), earthing strips at rear side, bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts, spring and washers. The cabinet and all members should be chemically treated with MSR solution for anticorrosive treatment and apply spray paint with two coat of synethetic enamel paint over a coat of red oxide primer. The panel should be suitable for 415 volts, 50Hz, 3 phase 4 wire system and internal connection should be provided with aluminium strips of suitable size and necessary foundation work and comprising following:-System Voltage-415V, 3-Ph, 4 wire, 50 HZAluminium BUSBAR rating -200 Amps, cable entry (incomming and outgoing ) form bottom with cable gland Incomming : 100 Amps MCCB TP, 36 KA of electric release with over load adjustment 0.4 to 1.0 In & short circuit electronic release adjustment 1.5 to 10.0 In (adjustment current with time), 415 Volts, 50 Hz-01 No Outgoing - (a) MCCB 4 pole 40 Amps 40 kA adjustable thermal release 0.64 to 10 In & adjustable magnetic release (3.5 to 10 In)- 01 Nos(b) MCCB 4 pole 40 Amps 63 kA adjustable thermal release 0.64 to 10 In & adjustable magnetic release (3.5 to 10 In)- 01 Nos-01 No (c) LED indicating lamps -03 Nos |
| 132 | Material and labour for sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 cm in depth after laying the Cable) and consolidated (punned) upto 18 cm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only shall be measured and paid for. |
| 133 | Material and labour for Brick with subclass 'B' bricks in cable protection, laying with built in each other complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysSep 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender