Tender For Welcome Maintenance / Certain Repairs To Offrs Md Accn To B1 Area Of Age B/R-Ii Under Ge (W) Jrc
Tender Value
45 Lakhs
Estimated cost
Bid Submission
01 Sep 2026
9 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalandhar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Welcome Maintenance / Certain Repairs To Offrs Md Accn To B1 Area Of Age B/R-Ii Under Ge (W) Jrc
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water remove Dust, debries/ rubbish etc, complete all as specified and as directed. |
| 2 | M&L rendering (Internal) 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. |
| 3 | M & L for preparation of newly plastered surface of wall and apply two coats of oil bound distemper over a coat of 1mm average thick wall putty, all as specified & directed. |
| 4 | Material and labour for 15mm thick cement plaster on brick or concrete surfaces in cement mortar (1:4) mixed with integral water proofing compound in the proportion recommended by manufacturer, surfaces finished fair and even complete all as specified and directed. (WPC shall be measured and paid separately under appropriate item of this BOQ). |
| 5 | Supply only integral water proofing compound all as specified and directed. |
| 6 | M&L for preparation of new plastered surface of wall and applying two coat of cement base paint, complete all as specified and directed. |
| 7 | M&L 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement all as specified |
| 8 | M & L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed. |
| 9 | M&L for complete removal of existing treatment of old decorated wall scraping down smoke soot, moulds, moss and efflorescent and trading oil and greasy spots etc (Plastered or unplastered surfaces) etc and applying one coat of acrylic exterior emulsion paint applying by mechanical spray gun complete all as per manufacturer instruction and as specified and directed by Engr-in-Charge. (Note :- height for bldgs up to four storey) |
| 10 | Material and labour for preparation of old decorated surfaces of walls, washing rubbing down and stooping of distempered and painted surfaces and applying one coat of oil emulsion distemper complete all as specified and directed |
| 11 | Material and labour for preparation of old decorated surfaces of walls, washing rubbing down and stooping of distempered and painted surfaces and applying two coat of oil emulsion distemper complete all as specified and directed |
| 12 | M&L complete removal of existing treatment on wall and applying two coat of oil emulsion distemper on one coat of putty filling 1mm thick on walls (surface finished even and smooth ), complete all as specified and directed. |
| 13 | M&L for preparation of old surfaces of walls including brooming down or steel wire brushing; scraping down smoke soot, moulds, moss and efflorescent and trading oil and greasy spots etc (Plastered or unplastered surfaces) and applying one coat of white (lime) wash complete all as specified and directed. |
| 14 | All as per item No 13 above but one coat of white wash on ceiling . |
| 15 | M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 16 | M&L for preparation of old steel surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 17 | Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed |
| 18 | M &L for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under:-(i) Application of Two component acrylic modified cementitious coating(aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coating and achieve a gripping profile that is clean, dry and free from laitance and dry other form of surface contamination. The installation instructions in manufacture's published literature should be strictly complied with, including but not limited to the following:-(bb) Chipping out any visible cracks in \\"V-Groove\\" pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/Dr Fixit 302 SBR latex/ Perma latex SBR/FOSROC Nitabond SBR latex/Asian paint latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required.(cc) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of sika Top Seal-107/Brush Bond FOSROC/Dr Fixit/STP/CICO.(dd) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified cementitious coating of SIKA Top Seal-107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions. (ee) Apply glass fabric sheet of SIKA Fab 1/FOSROC/Dr Fixit/STP whilst the first coat is wet.(ff) Once touch dry, apply second coat of Acrylic modified cementitious coating of SIKA Top Seal -107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions on the entire area.(gg) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat.(hh) The waterproofing coating should be taken to a height minimum 300mm above the finished floor level on the vertical surfaces three sides including dismantling of existing tiles.(jj) It is essential to cure Acrylic modified cementitious coating immediately after application (minimum 6-8hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking.(kk) A protection plaster 12-15mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with SIKA Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645.(ll) All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of Make SIKA Seal Tape/FOSROC/Dr Fixit/STP.(mm) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations.(nn)Waterproofing treatment has to be carried out through applicators authorised by the respective manufacturer's and approved by GE.(ii) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant.(iii) All CI traps in sunken slab to be enclosed with PCC 1:1.5:3 (Min 15cm) all around.(iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified.(v) Providing drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall ( Approx 450mm to 600 mm long ) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.(vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note:-Item No 25 (iv), (v) &(vi) shall be measured and paid separately. |
| 19 | M & L Cement concrete 1:5:10 type E-2 (using 40mm stone aggregate) as in sunken flooring complete all as specified. |
| 20 | S & F drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall (Approx 450mm to 600 mm long ) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. |
| 21 | M & L 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. |
| 22 | Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and disposal of rubbish outside MD land complete all as specified |
| 23 | Material and labour for non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors set and jointed in neat cement slurry and pointed in while or coloured cement to match over and including 15mm thick bedding layer CM 1:6 in complete all as specified |
| 24 | Material and labour for coloured glazed tiles of size 450x 300x7 mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 25 | M&L Vitrified Ceramic tiles light shade, 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour tiles over and incl 15mm thick screed bed in CM 1:6 all as specified. |
| 26 | All as per srl item No.25 above here-in-before but in skirting and 10mm thick rendering as backing coat of CM 1:4 |
| 27 | M&L for 20 mm thick machine cut granite (of any type ) tiles stone jointed with neat cement slurry mixed with pigment to match the colour of stone incl cutting and polishing and making hole in stone and RCC shelves suitable for gas pipe, with round edges where required and incl 15mm screed bed with CM1:6 including dismentling of existing granite complete all as specified and directed. |
| 28 | Petty repair to Steel rolling shutters system of size up to 12 Sqm and any description including reparing of ball bearing, top cover, anchoring rod, hasp and staple,gear operated system,crank handle, chain wheel and hand chain including necessary welding, grreesing etc and making the shutters complete serviceable including taking down & refixing in same opening all as per existing pattern as specified |
| 29 | M&L for plastering in patches not exceeding 3 sqm in each patch, 15 mm thick in cement mortar 1:6, finished even and smooth (without using extra cement) including taking down plastering and three coats of white/colour wash maching with existing surface complete all as specified. |
| 30 | M&L for plastering in patches not exceeding 3 sqm in each patch, 5 mm thick in cement mortar 1:3 on ceiling , finished even and smooth (without using extra cement) including taking down plastering and three coats of white wash complete all as specified. |
| 31 | M&L for repairing of RCC projections, chajjas , roofs, facia etc. in patches not exceeding 3 Sqm in each patch by necessary preparation i.e. scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, sufaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregate and reinforced with welded mesh of weight exc 2kg per sqmtr but n.exc 3kg/sqm with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches are n.exc 70mm including applying two coats of finishes to match with the existing surfaces in at any height complete all as specified. Note:- Cost of formwork and welded mesh shall be deemed to be included in unit rate quoted by the contractor. |
| 32 | Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area not exc 1.5 Sqm each all as specified. |
| 33 | All as per srl item No 32.00 above here-in-before but area exc 1.5 Sqm and not exc 4 Sqm each. |
| 34 | Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed. |
| 35 | Material and labour for framed work as in doors or gates of angle or other section with gusset plates, hold fast rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and directed. |
| 36 | S & F pressed steel frames 125x60mm as per IS for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including PCC 1:5:10, type B0 (20mm aggregate) filling in steel frame complete all as specified |
| 37 | All as per srl item No 36.00 above but 105x60mm size |
| 38 | S&F for 35mm thickness of factory made flush shutter solid core construction with block board core & ply wood face panels, commercial type on both side including 35 x 6 thick 2nd class Hard wood lipping on edge, complete all as specified and directed. |
| 39 | Supply and fixing glazed and skelton shutters factory made 35mm thick open rebated and prepared to receive glass, gauge etc (without sash bars) edging of framing plain, chamfered or rounded with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24(a) complete all as specified and directed |
| 40 | S&F Plain framed panelled shutter (two planel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of the rail and stile as per IS:1003(Part I), kiln sseasoned and chemically pressure treated 35mm thick. |
| 41 | S & F mild steel framed work for such as guard bars/grills,grating atc with end of bars shouldered and/ or riveted forged into spikes, framed guard bars barred iron door ,railings and similar work complete conforming to Fe-290 Gde E 165 including one shop coat of zinc chromate primer complete all as specified and directed |
| 42 | Supply and fixing sheet glass ordinary quality 4.0 mm thick in square not exc 0.50 Sqm each pane glazing with oil putty, clip in metal frame and wooden beading in wooden frame complete all as specified |
| 43 | M&L in repair for 4 mm thick plain glass fixing and glazing with oil putty/nails wire including haking out old broken glass in wooden/steel frame complete all as specified and directed |
| 44 | Supply and fixing galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified and directed. |
| 45 | Supply and fixing in repair galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified and directed. |
| 46 | M&L preparing New Wood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Pink Primer, complete all as specified and as directed. |
| 47 | M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a cot of primer, complete all as specified and directed. |
| 48 | S&F powder coated aluminium frame for doors, windows, partitions, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified. |
| 49 | S&F powder coated of any colour aluminum door shutters , aluminium section weighing not less than 0.55 Kg/ RM including necessary jointing cleats, glazing clips, ruber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed. |
| 50 | S&F powder coated of any colour aluminum window and ventilator shutters, side hung type with sash bars, aluminium section weighing not less than 0.55 Kg/ Rm including necessary jointing cleats, glazing clips, ruber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. |
| 51 | M&L for 5.50 mm thick glass sheet, ordinary quality and glazing with oil putty in square complete all as specified. |
| 52 | S & F factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen/Balcony Doors & Cabinets. |
| 53 | S & F factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) One side Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer-In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen/Balcony Doors and Cabinets. |
| 54 | S&F in repair 18/19mm thick MDF board, exterior grade, prelaminated on both side with decorative choice lamination, fixed with screws to timber frame work, including 18/19mm wide, 6mm thick 2nd class HW lipping on edges complete all as specified and directed. |
| 55 | Resecuring or earsing and adusting without taking down of shutters of any description exc 1 sqm and n-exc 2 sqm each complete all as specified and directed. |
| 56 | S & F in repair 12 mm plywood, grade BWR type BB fixed with screw to timber frame work for shutter,shelves etc including removing old work from site any thickness complete all as specified |
| 57 | Petty repair to wooden/PVC Cup Board shutters by making minor adjustment to hinges etc easing shutter incl taking down of shutter if required and refixing in same position including welding to angle iron chowkhats |
| 58 | Petty repair to PVC door shutters by making minor adjustment to hinges etc easing shutter incl taking down of shutter if required and refixing in same position including welding to angle iron chowkhats |
| 59 | S & F in repair steel window handle MS painted with black japan left or right side complete fixed as directed by Engineer-in-Charge |
| 60 | Welding in repairs not exceeding 2.5 cm in length & thickness of metal to be welded not exceeding 6 mm complete all as specified including material & labour. |
| 61 | S&F 40mm wide 3 to 6 mm thick tappered rubber beading fixed to door shutter with nails as in repair all as specified. |
| 62 | S&F 2nd class hard wood plain fillets square or rectangular or tri angular in section and bull- nosed, splayed, chamfered or rounded on one edge or face, clean sawn planed on both sides secured with nails or beads in section exc 3 sq cm but not exc 6 sq cm including painting all as specifier and directed. |
| 63 | M&L in repair for stainless steel pipe 25 mm dia curtain rod fixed with finials including pair of decorative complete pair of side brackets (both side), shade as approved by GE all as specified. |
| 64 | S & F in repair 20mm dia curtain rails stainless steel , chromium plated fixing in cup board with brackets, stops, rollers etc, all as specified |
| 65 | S&F 50 X 15 mm size magnet door catcher for closing for PVC shutter/cupboard complete as specified and directed. |
| 66 | S&F 100 mm size MS mat / glossy finish handle complete as specified and dirceted. |
| 67 | S&F auto hinges for cabinet case (Make ; KARF/HETICH or equivalent) |
| 68 | S&F Mild steel rollers and plate suitable for sliding drawers, complete all as specified and directed. |
| 69 | Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing |
| 70 | Supply and fixing PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing |
| 71 | S&F 100mm size MS butt hinges medium weight , complete all as specified and directed. |
| 72 | S&F100mm size stainless steel butt hinges for fixing to PVC doors all as specified. |
| 73 | Supply and fixing aluminium anodised barrel tower bolts of extruded section 150mm long, complete all as specified and directed. |
| 74 | All as per item No.73 above but in repairs |
| 75 | Supply and fixing aluminium anodised barrel tower bolts of extruded section 200mm long, complete all as specified and directed. |
| 76 | All as per item No.75 above but in repairs |
| 77 | S&F Extruded aluminium alloy handles, fabricated type,anodised 100 mm in size, complete all as specified and directed. |
| 78 | All as per item No.77 above but in repairs |
| 79 | S&F Extruded aluminium alloy handles, fabricated type,anodised 150 mm in size, complete all as specified and directed. |
| 80 | All as per item No.79 above but in repairs |
| 81 | S&F Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 250mm long, complete all as specified and directed. |
| 82 | All as per item No.81 above but in repairs |
| 83 | S&Fin repair mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate in repair complete all as specified and directed. |
| 84 | Supply & fixed floor door stopper(double) of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door overall length of cover plate 140mm complete all as specified |
| 85 | All as per item No.84 above but in repairs |
| 86 | S&F continuous (Piano) hinges, mild steel, bright finish or electro galvanised width of flaps 40 mm when open complete all as specified. |
| 87 | S & F 100 mm Hasp & Staple extruded aluminium alloy , fabricated type, anodised including bolt to hinge plate and fixed with screws with Cup Board shutter, All as Specified |
| 88 | All as per item No.87 above but in repairs |
| 89 | S&F in replacement aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 Kg complete all as specified as directed. |
| 90 | S&F Rim latch 125 mm with two levers, of mild steel body stove enamelled finish; with brass knob or lever handle and fixed all as specified directed by Engr-in-Charge. |
| 91 | S&F in repairs 40 mm dia powder coated cup board knobs fixed with nut, screws and washer of mild steel bright finish complete all as specified. |
| 92 | Supply and fixing in repair Bib tap chromium plated, cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete all as specified and directed. |
| 93 | S&F in repair fancy CP center hole basin mixer (Swan Neck) of Make cera, Jaquar Cat No FLR-5167NB or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. |
| 94 | S&F in repair fancy CP pillar cock with lift type operating, chromium plated of make cera,Jaquar CAT No FLR-5015 or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. |
| 95 | S&F in repair fancy CP Concealed Stop Cock with Adjustable Wall Flange make,cera, Jaquar CAT No OPP-15083KPM or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. |
| 96 | S&F in repair fancy CP angular stop Cock with Wall Flange of make ,cera,Jaquar CAT No OPP-15053PM or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. |
| 97 | S&F in repair fancy CP 2 way angular stop Cock with Wall Flange Make,cera, Jaquar Cat No 6811 or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. |
| 98 | S&F in repair fancy Wall Mixer 3-in-1 with provision for both Over Head Shower and Hand Shower complete with 115mm long bend Pipe, connecting legs & wall flange of makes of Make cera,Jaquar Cat No FLR-5281N or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. |
| 99 | S&F in repair fancy CP Sink cock swinging spout (Wall mounted) with connecting legs & wall flanges of Make cera,Jaquar Cat No FLR-5347N or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed |
| 100 | S&F in repair fancy Over Head Shower square wall shower (Adjustable) of size 100mm including all fittings of Make cera.Jaquar Cat No OHS-1661 or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed |
| 101 | S&F in repair fancy Hand Shower 100mm round shape(ABS Body chrome plated with Gray face plate) with 1.50 Mtr flexible tube and hook of Make cera,Jaquar Cat No HSH-1937 or Kohler suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. |
| 102 | S&F in repair fancy towel rail/rod, D type, 600mm long of Make cera,Jaquar Cat No CAN-1111SM or Kohler fixing with Chromium plated Brass Screws and Wooden/Plastic Cleats, complete as all specified and as directed. |
| 103 | S&F in repair fancy towel ring square type flange of Make cera,Jaquar Cat No CAN-1121N or Kohler fixing with Chromium plated Brass Screws and Wooden/Plastic Cleats, complete as all specified and as directed. |
| 104 | S & F in repair health faucet 1.00mtr long flexible tube & wall hook of Make,cera, Prayag Cat No BEA-41 or Jaquar/Kohler suitable for 15mm dia for iron pipe or for brass ferrule all as specified & directed. |
| 105 | S & F in repair Jet spray with holder for EWC 1.00 mtr long of Make Prayag Cat No BEA-17 or equivalent makes of Group I of Appx “B” suitable for 15mm dia for iron pipe or for brass ferrule all as specified & directed. |
| 106 | S&F in repair, toilet paper holder of MAKE: cera,Jaquar CAT No. CAN-1153S or Kohler and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 107 | S & F in repair PVC connection, heavy duty 15 mm bore, 45 cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed. |
| 108 | S & F in repair new flexible PVC waste pipe of approved quality 32 mm bore, 75 cm long with one end socketed fixed to waste coupling including one PVC reducer 32mm complete all as specified and directed |
| 109 | S&F in repair, Coloured PVC bath Cabinet of size 450x450x90mm with Looking Mirror (as approved) fixing with Chromium plated Brass Screws and Wooden/Plastic Cleats, complete as all specified and as directed. |
| 110 | S&F in repairs bevelled edge looking mirror of selected quality glass, 5.5 mm thick of size 450 x 600 mm, PVC moulded case mounting on 6 mm thick AC building board or commercial ply wood on back and fixed to wooden plugs with chromium plated brass screws and cup washers, fixed in repairs, complete all as specified and directed |
| 111 | S&F in repair, Sheet Glass Shelf Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete all as specified and as directed. |
| 112 | S&F in repair, Sheet Glass Corner Shelves Assembly (Transparent), consisting of 5.5mm thick Sheet Glass Shelf with Chromium plated Bracket Guard and Railing, Make Jaquar CAT No CAN-1173 or kohler complete all as specified and as directed. |
| 113 | S&F in repair fancy chromium plated soap dish, complete all as specified and directed. Make : Prayag or equilvant |
| 114 | S&F Vitreous China White Wash Down Water Closet Pan (EWC) with Trap and Fixing Bolts (excluding Flushing Cistern and Flush Pipe) including connection to drain (or outgoing pipe) and to Flushing Pipe, Anti-syphonage Pipe, etc. and Making Good to Floor /distrubed surfaces including dismantling the existing unserviceable Water Closet complete all as specified and as directed. |
| 115 | S&F coloured vitreous china wash down one piece water closet with seat cover , hinges, Accessories set, size 380x655x765mm floor mounted of make cera,Jaquar CAT No-LYS-WHT-38751P180UFSMZ fitting with twin flush fitting with inlet ball valve float and handle, incl fixing bolt, with bottom and cover and mild steel chromimum plated hinging device with complete fixed in repairs all as specified and directed. |
| 116 | S&F Vitreous China White Squatting Pan, ‘ORISSA’ Pattern of size 580x440 mm with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces and fixed-in-repairs, complete all as specified and as directed. |
| 117 | S&F in repair, White Plastic Water Closet Seat Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device, complete all as specified and as directed. |
| 118 | S&F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, syphonic action type with Inlet, Ball Valve, Float and handle, a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including dismantling the existing unserviceable Cistern complete all as specified and as directed. |
| 119 | S&F Vitreous China Wash Hand Basin of size 550x400mm (Flat Back or Angle Back type) with pedestal including 32mm bore (dia) Brass Chromium plated Waste Fitting, a pair of Cast Iron Bracket duly painted / Erecting Stand including cutting and pinning in Ends Making Good disturbed Surfaces in Cement Mortar 1:3 including dismantling the existing unserviceable Wash Basin complete all as specified and as directed. |
| 120 | S&F in repair, Stainless Steel Sink with Drainage Board 1.0mm thick Over-all size 915x460mm and Bowl size 410x330x160mm for Kitchen or Laboratory with Plugs, Washers, Waste Fitting 32mm bore (dia) of Brass Chromium Plated, a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed. |
| 121 | S&F in repair sink made of stainless steel 1mm thick, kitchen or laboratory, with plugs, washers and wastes coupling, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm (minimum), complete all as specified and directed. |
| 122 | S&F in repair, Stainless Steel Kitchen Rack of size 750x800x200mm (Thickness of Sheet not less than 0.63mm) with Mild Steel Brackets and fixed to Wooden Plugs with Chromium Plated Brass Screws and Cup Washers, complete all as specified and as directed. |
| 123 | S&F chromium plated grating 100 mm dia circular of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap complete all as specified and directed. |
| 124 | S&F in repairs 32mm dia PVC waste coupling for WHB or Sink (half or full threaded) complete all as specified and directed |
| 125 | M&L for chromium plated peg set of 5 (PTMT), fixed with screws and plugging to rear side of door shutter in bath, complete all as specified and directed. |
| 126 | M&L dis-connecting existing PVC tank of any capacity, setting aside (or lowering, if required) for repairs, cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes etc and finally washing the internal surfaces with bleaching powder/soap solution etc, re-connecting and re-fixing in position including making connections complete all as specified and directed. |
| 127 | S & F rotational moulded synthetic (HDPE), UV Coating, water storage tank 500 litre capacity (cylinderical vertical with closed top,) hoisted & fixed in position all as specified in SSR Part-I, including dismantling of existing water tank, complete all as spfd & directed. |
| 128 | S & F rotational moulded synthetic (HDPE), UV Coating, water storage tank 1000 litre capacity (cylinderical vertical with closed top,) hoisted & fixed in position all as specified in SSR Part-I, including dismantling of existing water tank, complete all as spfd & directed. |
| 129 | S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 mm - 210 gms./ 25mm-455gms/ 40mm - 690 gms) complete all as specified. |
| 130 | S&F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 mm - 210 gms./ 25mm-455gms/ 40mm - 690 gms) complete all as specified. |
| 131 | S&F in repair 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 132 | S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 133 | Taking down old steel tubing & connection including cleaning for refixing for 15mm bore pipe complete all as specified |
| 134 | Taking down old steel tubing & connection including cleaning for refixing for 20mm bore pipe complete all as specified |
| 135 | M&L Galvanised iron water tubing 15 mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc complete all as specified |
| 136 | All as per srl item No. 135.00 here-in-before but for 20mm bore tube |
| 137 | M&L CPVC water tubing 20 mm outer dia, with & including all fittings fixed to wall, ceilings and or laid in floors etc, complete all as specified |
| 138 | All as per srl item No. 137.00 here-in-before but for 25mm bore tube |
| 139 | M&L in repair CPVC reducer 20mm to15mm, complete all as specified |
| 140 | S&F for PVC cover of water tank maching with existing water tank complete all as specified |
| 141 | Petty repair to leaking flushing cistern low/high level, incl adjustment in the internal fitting repair to PVC bends pipe, flush pipe etc all as per directed by Engineer-in-Charge |
| 142 | S&F in repair new ware PVC Syphon For Flush Tank (White) Cistern Part Flush Tank Lever as specified and directed by Engr -in-charge. |
| 143 | Petty Repair for stop leaking Bib tap/ Pillar tap/Stop cock by suitable jumper washer and etc, complete all as specified |
| 144 | Dismantling of brick work or stone/boulders masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars etc. and rubbish materials remove from site all as specified and directed |
| 145 | Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 |
| 146 | All as per Item No 145.00 above but except bricks |
| 147 | Demolition of reinforced cement concrete(reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for. Complete all as specified and directed by Engineer-In-Charge |
| 148 | M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engineer-in-Charge |
| 149 | Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal/sloping), fair finished surfaces concrete flat, complete all as specified and directed by Engineer-in-Charge |
| 150 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to. Complete all as specified and directed by Engineer-In-Charge |
| 151 | M&L for grubbing up bushes or trees trunk of girth n. exc. 10cm including cutting of tree/bushes grown in/over walls, digging out roots and making good the disturbed portion of wall with PCC (1:3:6) type C-1 using 20mm graded stone aggregate including matching the same complete all as specified & directed. |
| 152 | Cleaning of roof removing bushes, mud, debries, digging out Existing Surface roots and making good the disturbed portion of roof tiles with tiles including matching the same complete all as specified & directed. |
| 153 | Taking down eaves gutters and rainwater pipes/sewage pipe (any size or pattern ),including all fittings,heads,shoes,bends,swan necks etc.including cleaning or refixing or removal to store. |
| 154 | S&F 110 mm bore PVC pipes single socketed in any length with rubber ring joints fixed to walls or laid in floor, complete all as specified and directed. |
| 155 | S&F 75 mm bore PVC pipes single socketed in any length with rubber ring joints fixed to walls or laid in floor, complete all as specified and directed. |
| 156 | S&F 110 mm dia PVC (SWR ) bends any radius complete all as specified and as directed. |
| 157 | S&F 75 mm dia PVC (SWR ) bends any radius complete all as specified and as directed. |
| 158 | S&F 110 mm dia PVC (SWR ) branches piece,double (double Y) equal or unequal with rubber rings ljoits fixed to walls complete all as specified and as directed. |
| 159 | S&F 75 mm dia PVC (SWR ) branches piece,double (double Y) equal or unequal with rubber rings ljoits fixed to walls complete all as specified and as directed. |
| 160 | S&F 75mm dia PVC (SWR ) vent cowl complete all as specified and as directed. |
| 161 | M&L 75mm PVC (SWR) PVC (SWR) floor trap, plain with grating including jointing with solvent cement fixed in repairs complete all as specified and directed. |
| 162 | Demolition of cement concrete in ground floors and paving n. exc 15 cm thickness (below or above the ground level) complete all as specified and directed. |
| 163 | Material and labour for 75mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth with using extra cement complete all as specified and directed. |
| 164 | M&L for PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in roof padding ,Complete all as specified and directed by Engineer-In-Charge |
| 165 | M&L for 10mm thick screed bed or bedding layer of mortar in CM 1:4, using WPC. Complete all as specified and directed by Engineer-in-Charge. |
| 166 | M&L for painting the roof surface with a coat of hot blown paving industrial bitumen 85/25 at the rate of 1.20 kg/sq M over a coat of primer @ 0.3 litre per Sqm Complete all as specified and directed by Engineer-In-Charge |
| 167 | M&L for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick reinforced with five layer polyster non wove fabric (wi Not less than 150 gms/sqm) land on bitumen coted surface by forced application. Complete all as specified and directed by Engineer-In-Charge |
| 168 | M&L for applying two coats of aluminium paint over laid APP surface after proper cleaning complete all as specified and directed by Engineer-In-Charge |
| 169 | Taking down carefully aluminium / copper point wiring (light / fan / socket or power) while not disturbing existing conduit complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls and floors and one coat of putty and two coat of distemper as per existing colour complete all as directed . |
| 170 | Taking down sub main wiring of two single core PVC cable PVC insulated 4 / 6/10 sqmm including conduit or wooden batten and remove from the site of work and making good the disturbed surfaces of wall or floor etc. and one coat of putty and two coat of distemper as per existing colour complete all as directed by Engineer-in-Charge. |
| 171 | Taking down main switch / DB and making good the disturbed surface and one coat of putty and two coat of distemper as per existing colour complete all as directed by Engineer-In-Charge. |
| 172 | M&L for point wiring with 1.5 sqmm, PVC insulated but sheathed, stranded copper conductor single core FRLSH cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia (minimum) or higher size as specified and cutting chasing on wall/ground complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc/ fittings ISI marked for modular fittings and brass screws and cup washers including 1.5 sqmm stranded copper conductor PVC insulated FRLSH cable green in colour as continuous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed. Note : 1. Cost of Metal boxes and modular accessories like cover plates will be paid seprately in respective items) (a) Fan point/ exhaust fan point / one light point / bell/ buzzer controlled by one switch/ bell push. |
| 173 | (b) One socket outet point 5 amps on the same board. |
| 174 | (c) One socket outet point 5 amps on the independent board. |
| 175 | All as Ser item 172.00 here in before but with 2.5 sq mm wire and earth wire (green colour) of 2.5 sq mm for 3 Pin 15 Amp modular type socket outlet. |
| 176 | M& L for concealed point wiring complete with 4 sq mm single core multistranded copper conductor FRLSH, PVC insulated and unsheathed cable 1100 volt grade drawn through & including PVC conduit, medium grade with accessories like bends, tees, junction boxes etc for power point of AC all as specified including 4 sqmm, FRLSH type, copper multistranded cable as earth wire for AC socket complete all as directed by EIC |
| 177 | Supply and fixing modular metal flush box 1/2 module complete all as specified and directed. |
| 178 | Supply and fixing modular metal flush box 3 module complete all as specified and directed. |
| 179 | Supply and fixing modular metal flush box 6 module complete all as specified and directed. |
| 180 | Supply and fixing modular metal flush box 12 module complete all as specified and directed. |
| 181 | Supply and fixing modular white cover plate with frame, 1 module complete all as specified and directed. |
| 182 | Supply and fixing modular white cover plate with frame, 3 module complete all as specified and directed. |
| 183 | Supply and fixing modular white cover plate with frame, 6 module complete all as specified and directed. |
| 184 | Supply and fixing modular white cover plate with frame,12 module complete all as specified and directed. |
| 185 | Supply and fixing modular Dummy plate complete all as specified and directed. |
| 186 | Supply and fix in repair Modular switch 6 Amps single pole one way as per existing make & model/ as per sample . Note : All switches from 6 Amp to 25 Amp should be latest ISI marked as per IS 3854 : 2023 |
| 187 | Supply and fix in repair Modular switch 16 Amps single pole one way as per existing make & model/ as per sample . Note : All switches from 6 Amp to 25 Amp should be latest ISI marked as per IS 3854 : 2023 |
| 188 | Supply and fix Modular multi socket 3 pin and 2 pin 6 Amps round and flat as per existing make & model/ as per sample . Note : Sockets 6 Amp 3 Pin and 6/16 Amp 3 Pin combined should be latest ISI Marked as per IS 1293 : 2019 and should be supplied with shutters and shutters opening with phase and neutral simultaneously. The range should have all the types of Indian Standard or Multistranded International sockets range in their profile. |
| 189 | Supply and fix in repair Modular socket 6A /16 A Twin socket heavy duty as per existing make & model/ as per sample/EIC . Note : Sockets 6 Amp 3 Pin and 6/16 Amp 3 Pin combined should be latest ISI Marked as per IS 1293 : 2019 and should be supplied with shutters and shutters opening with phase and neutral simultaneously. The range should have all the types of Indian Standard or Multistranded International sockets range in their profile. |
| 190 | M&L for point wiring with PVC insulated, PVC sheathed cable single core stranded copper conductor FRLSH cable 1.5 sqmm size, 1100V grade, drawn into and including/Exixsting PVC rigid concealed conduit medium grade (ISI marked) with and including PVC unsheathed cable single core copper FRLSH conductor 1.5 Sqmm as continuous earth wire and including pressed MS sheet sunken box 1.6 mm thick with 3 mm thick laminated bakelite sheet all as specified & directed by EIC.for light/fan/call bell point |
| 191 | All as per Ser item No 190.00 above but for 5 amps switch socket combination on independent board |
| 192 | All as per Ser item No 190.00 above but for 5 amps switch socket combination on same board |
| 193 | All as per Ser item No 190.00 above but with 2.5 sq mm cable for 15 amps switch socket combination outlet on independent board complete all as specified and directed. |
| 194 | S&F switch piano flush type, 5 amps, 230V AC, single pole, one way. |
| 195 | S&F socket out let 5 amp 5 pin flush type. |
| 196 | S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type. |
| 197 | S&F bell push type 5 Amps. |
| 198 | S&F call bell ding dong AC 230 volts. |
| 199 | Supply & fixing ceiling roses surfaces bakelite two three terminals 65 x 50 mm all as specified. |
| 200 | Supply & fixing lamp holder PVC, insulated body with back plate suitable for batten fittings including LED lamp 9W BEE Energy star rating of five star all as specified. |
| 201 | Supply and fix in repair modular/BLDC fan regulator step type 240 V, 120 W , 2 modules all as as per existing make & model/ as per sample . |
| 202 | Supply and Fixed single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of cap 20A complete all as specified and directed. |
| 203 | Supply & fixing of 20 Watt Batten luminaire with Polycarbonate Housing with high quality opal finish diffuser. The luminaire should have a CRI > 80 and CCT of 6500K. The luminaire shall be compliant with IP20 and IK02 classification. Luminaire shall be designed to emit at least 2000 nominal lumens and an System efficacy of at least 100 lumen/watt and maximum system wattage of 20 Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 45 deg C. The electronic driver used shall have a power factor >0.95 and THD <10% and suitable for an operating voltage range of 140-270V AC. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. |
| 204 | SITC of high-quality integrated LED Street Light with a minimum system lumen of4750 Lm and system wattage not exceeding 45W with a nominal efficiency 105 lumen/watt. CCT of 5700K with SDCM of < 5 and CRI >70. The housing should be of non-corrosive high-pressure die-cast aluminum with high efficiency LEDs as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with PF > 0.95. Lifetime of 50K hours @L70. The Luminaire should have Powered by integral, Isolated LED electronic driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection (Operation at 440 V AC), Over Voltage protection, Surge Voltage protection upto 4 kV.Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/ULaccredited lab to verify above parameters complete all as specified and directed. |
| 205 | Supply & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type ,MCB should be having the Breaking Capacity of 10 kA and should be ISI marked as per IS/IEC 60898-1 2002 with “B” Curve Characteristics. Should have bi-connect terminals on the bottom terminals for looping and should have 35 sq mm termination capacity on both terminals with insulated sliding shutters for making it IP-20 protected & with two position DIN Rail Clamp for easy mounting. complete all as specified and directed. |
| 206 | S & F MCB SPN, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type ,MCB should be having the Breaking Capacity of 10 kA and should be ISI marked as per IS/IEC 60898-1 2002 with “B” Curve Characteristics. Should have bi-connect terminals on the bottom terminals for looping and should have 35 sq mm termination capacity on both terminals with insulated sliding shutters for making it IP-20 protected & with two position DIN Rail Clamp for easy mounting. complete all as specified and directed. |
| 207 | Supply and fix Sheet metal DB,double door, SPN 8 way for MCB, 240 volt with 200 amps rated bus bar , neutral bar / connectors suitable copper thimbles , lugs etc. Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 100 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed. |
| 208 | S & F MCB TPN, 240 volts, 40 Ampere, rupturing capacity 10 KA, ‘B’ curve type ,MCB should be having the Breaking Capacity of 10 kA and should be ISI marked as per IS/IEC 60898-1 2002 with “B” Curve Characteristics. Should have bi-connect terminals on the bottom terminals for looping and should have 35 sq mm termination capacity on both terminals with insulated sliding shutters for making it IP-20 protected & with two position DIN Rail Clamp for easy mounting. complete all as specified and directed. |
| 209 | Supply & fixing MCCB 4 pole of capacity 63 Amps with breaking capacity 16 Kilo Amps including all electrical connections and fixing arrangment complete all as specified and directed by EIC . Note- MCCB Should have reverse load and line termination, rotary handles – direct and variable depth and common auxiliaries for entire range. Should be CE marked and conform to IEC 60947-2. MCCB should have the maximum operational voltage ( Ue ) of 550 Volts (AC 50/60 Hz), Insulation Voltage ( Ui ) of 800 Volts and Rated Impulse Withstand Voltage (Uimp) not less than 8000 volts. The MCCB should have been designed at an ambient temperature of 50 degree centigrade. MCCBs shall be actuated by a rotary-handle that clearly indicates the three distinctive positions: ON, OFF and TRIPPED.For 16 – 125 A: Should have breaking capacity of min. 16 kA with thermal release adjustable from 80 to 100 % & fixed magnetic release and with Ics = 100% Icu. |
| 210 | Supply and fix MCB DB, TPN 4 way double door suitable for mounting of MCB TPN as incomer with suitable 200 amps rated bus bars , Neutral links , blanking plates. Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 200 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed by EIC . All 3 Phase horizontal distribution boards should have the provision to convert the distribution boards to Per Phase Isolation Distribution Board at site. |
| 211 | Supply and fix MCB DB, TPN 4 way double door Vertical type suitable for mounting of MCCB as incomer with suitable 200 amps rated bus bars , Neutral links , blanking plates. Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 200 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed by EIC . All 3 Phase horizontal distribution boards should have the provision to convert the distribution boards to Per Phase Isolation Distribution Board at site. All MCCB incomer distribution boards should be supplied with 250 Amp rated fully shrouded busbars. |
| 212 | Supply & fixing MCCB 4 pole of capacity 100 Amps with breaking capacity 16 Kilo Amps including all electrical connections and fixing arrangment complete all as specified and directed by EIC . Note- MCCB Should have reverse load and line termination, rotary handles – direct and variable depth and common auxiliaries for entire range. Should be CE marked and conform to IEC 60947-2. MCCB should have the maximum operational voltage ( Ue ) of 550 Volts (AC 50/60 Hz), Insulation Voltage ( Ui ) of 800 Volts and Rated Impulse Withstand Voltage (Uimp) not less than 8000 volts. The MCCB should have been designed at an ambient temperature of 50 degree centigrade. MCCBs shall be actuated by a rotary-handle that clearly indicates the three distinctive positions: ON, OFF and TRIPPED.For 16 – 125 A: Should have breaking capacity of min. 16 kA with thermal release adjustable from 80 to100 % & fixed magnetic release and with Ics = 100% Icu. |
| 213 | Supply and fix MCB DB, TPN 6 way double door Vertical type suitable for mounting of MCCB as incomer with suitable 200 amps rated bus bars , Neutral links , blanking plates Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 200 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed by EIC . complete all as specified and directed. All 3 Phase horizontal distribution boards should have the provision to convert the distribution boards to Per Phase Isolation Distribution Board at site. All MCCB incomer distribution boards should be supplied with 250 Amp rated fully shrouded busbars. |
| 214 | M & L for sub main wiring with 1100 volt grade two single core FRLSH Wire PVC insulated and unsheathed cable with stranded copper conductor 10 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 10 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed. Note : Four runs of 10 sqmm PVC FRLSH multi stranded copper cable wire and One run of 10 sqmm PVC FRLSH multi stranded copper cable earth wire and One run (01 meter) PVC conduit of suitable size ISI mark will be measured and one unit length. |
| 215 | All as per ser item No. 214.00 above but for sub main wiring with 2 run of 6 sqmm & 1 run of 6 sqmm as earth wire |
| 216 | All as per ser item No. 214.00 above but for sub main wiring with 2 run of 4 sqmm & 1 run of 4 sqmm as earth wire |
| 217 | SITC of new generation, post top, energy saving spun aluminium landscape luminaries with high power 40W LED , IP65 protection suitable for Pole dia 76mm pole complete with all accessories. Luminaire shall be made of pressure die cast/spun aluminium housing with high transmission clear diffuser, corrosion resistant powder coated finish, high efficiency LED driver with surge protection, minimum system efficacy 100 lm.W, CCT 3000K/4000K/6500k, CRI > 80, operating voltage 140-270 V AC complete all as directed by EIC. |
| 218 | Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circulat of size 10 Sqmm 2 Core complete. |
| 219 | Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circulat of size 6 Sqmm 2 Core complete. |
| 220 | S&F SITC of decorative wall light fixture made up of polycarbonate/glass die cast aluminium housing with poder coated finish 10 W to 15 W ,IP43 protection and BIS certified inbuilt LED driver, glare free uniform illumination complete with mounting base, hardware, lamp and connection as required at site all as specified and directed by EIC.Reputed make as approved by Engineer-in-charge before installation. |
| 221 | S & F 10W LED Bulk LED fitting and connecting electricity using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed |
| 222 | S & F LED Mirror light 10W connecting electricity using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed. |
| 223 | S&F SITC Bed side Reading light suitable for VIP room/Officer accomodation and residential bedroom application, 8-10 Watt, 800 to 1000 lumens , CRI > 80, 3000K/4000K/6000K, elegant design, energy efficient LED light source, manufactured from high quality and durable materials with focused glare-free illumination, flexible/adjustable arm or fixed modern arhitrctural pattern as approved by EIC and shall be made of high quality powder coated die cast aluminium/MS body with superior finish and polycarbonate/acrylic diffuser, conforming to latest IS standards with long life and superior illumination quality with all accessories and electrical connection as required & all as specified and directed by EIC. White/Black/ equivalent as approved. Please Enable Macros to View BoQ information |
| 224 | S&F SITC Bed side Reading light suitable for VIP room/Officer accomodation and residential bedroom application, 8-10 Watt, 800 to 1000 lumens , CRI > 80, 3000K/4000K/6000K, elegant design, energy efficient LED light source, manufactured from high quality and durable materials with focused glare-free illumination, flexible/adjustable arm or fixed modern arhitrctural pattern as approved by EIC and shall be made of high quality powder coated die cast aluminium/MS body with superior finish and polycarbonate/acrylic diffuser, conforming to latest IS standards with long life and superior illumination quality with all accessories and electrical connection as required & all as specified and directed by EIC. White/Black/ equivalent as approved. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysSep 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender